ALH35573110VHF FM REPEATER

TKR-751 FCC ID: ALH35573110 TKR-851-1 FCC ID: ALH35583110 INSTRUCTION MANUAL TKR-751/TKR-851-1 THANK YOU! We are grateful you purchased this KENWOOD repeater. We believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency. KENWOOD incorporates the latest in advanced technology into all of our products. As a result, we feel strongly that you will be pleased with the quality and features of this product. FEATURES • You can easily program channel data using the KPG-91D software on a PC. • You can recall 1 of 16 preset channels using either a PF key or the external control line. • The firmware can be written to the Flash memory through an external source. • QT/DQT signalling can be programmed on each channel. It simultaneously decodes up to 16 different QT/DQT tones. • Air Remote Control Function. • The interface port can be used with external equipment, such as a repeater controller. • The repeater has multi-mode capability. Wide: 30 kHz / Narrow: 15 kHz (TKR-751; K type only) Wide: 25 kHz/ Narrow: 12.5 kHz (TKR-751/TKR-851) • You can adjust the following functions from a PC: • Squelch • RX Audio Signal Output (RA) • RX Detector Signal Output (RD) • RX Frequency • RF Output Power • Maximum Deviation • TX Audio Input (TA) • Signaling Deviation (TD) • DQT Balance • QT Deviation • DQT Deviation • Test Tone Deviation • CW ID Deviation • Repeat Gain • TX Frequency • DTMF Deviation • Courtesy Tone Deviation • Battery Operating Tone Deviation • Battery Warning Tone Deviation • Power Down Detect • 5 Tone Deviation (M type only) TKR-751 FCC ID: ALH35573110 TKR-851-1 FCC ID: ALH35583110 PRECAUTIONS • Do not expose the unit to rain or moisture; to prevent fire or electric shock. • Do not open the unit under any circumstances; to avoid risk of electric shock. • Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. • Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. • If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your KENWOOD service center or dealer. NOTICES TO THE USER UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking information is for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Item Part Number Quantity Hardware fixture J21-8402-#4 1 Front Glass B10-2635-#4 1 Filter B11-1259-#4 1 Cushion G13-1801-#4 4 Cushion G13-1802-#4 4 Foot J02-0475-#5 2 Foot J02-0492-#4 2 Grommet J59-0302-#5 2 Handle K01-0418-#5 1 Screw N30-4006-46 2 Screw N35-3006-45 5 DC Cord E30-3427-#5 1 Connector Cable E31-3228-#5 1 Fuse F06-1032-#5 1 Instruction Manual B62-1775-## 1 Warranty Card 1 FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. ** GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ** ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. ** REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. CAUTION: This repeater is intended for use as a fixed base station with the antenna located outdoors on the rooftop or on antenna tower. TKR-751 FCC ID: ALH35573110 TKR-851-1 FCC ID: ALH35583110 INSTALLATION To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws. Please consult your dealer for installing the repeater and antenna. MICROPHONE Connect an optional KMC-30, KMC-27A, KMC-27B, or KMC-9C KENWOOD microphone to the MIC jack on the front panel. CONTROLS AND FUNCTIONS ** Front Panel 1 Speaker 2 CH/STATUS Display Two, 7-segment digits display the channel number or status. 3 VOLUME control Rotate to adjust the volume. 4 DC SOURCE switch 5 Power indicator Lights green when power is applied from the DC 13.6V jack. Lights red when power is applied from the BACKUP battery terminal. 6 Mic jack Connect a microphone to this 8-pin modular jack. 7 Programmable Function keys Press these keys to activate their programmable functions. 8 BUSY indicator Lights green while a signal is being received. 9 TX indicator Lights red while transmitting. ** Rear Panel 1 TX OUT jack Connect a TX antenna or a duplexer ti this receptacle. 2 CONTROL I/O jack Connect an external programming device or repeater controller to this DB-25 interface. 3 FUSE Insert 10 A blade fuses into these fuse holders. 4 RX IN jack Connect a RX antenna or a duplexer to this BNC receptacle. 5 DC 13.6V jack Connect a 13.6 V DC power supply to this jack. 6 BACKUP battery terminal 7 TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack. TKR-751 FCC ID: ALH35573110 TKR-851-1 FCC ID: ALH35583110 REPEATER OPERA TION Note: Please consult your dealer for programming the repeater. When power is applied to the unit, the POWER indicator lights. • Green when using the main DC jack. • Red when using the Backup terminal. Rotate the VOLUME control to adjust the volume. The BUSY indicator lights green while receiving a signal and the TX indicator lights red while transmitting. TRANSCEIVER OPERA TION ** Receive Adjust the volume to your desired level. You may need to readjust the volume when you receive a message from your dispatcher or another member in your fleet. • The BUSY indicator lights green while a signal is being received. ** Transmit 1 Listen to the channel before transmi…

Text truncated - open the document above for the full version.

January 21, 2004 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Reference: This equipment meets the requirements of FCC Rules, Parts 90.203(e) and (g) as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely yours, Morton Flom, P. Eng.

1/21/2004 Federal Communications Commission EQUIPMENT APPROVAL SERVICES P.O. Box 358315 Pittsburgh, PA 15251-5315 Attention: Authorization and Evaluation Division Reference: FCC ID: ALH35573110 Model: TKR-751 Dear Sir: Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of some of the information accompanying this Application, as listed below: Block Diagram Schematic Diagrams Circuit Description Parts List Active Devices Tuning Procedure These materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457 (d)(1)(ii), disclosure of the Application and all accompanying documentation will not be made before the date of Grant for the Application. Sincerely yours, Morton Flom, P. Eng.

TKR-751 FCC ID: ALH35573110 Rear View Front View TKR-751 FCC ID: ALH35573110 Top View Bottom View TKR-751 FCC ID: ALH35573110 Left View Right View

TKR-751 FCC ID: ALH35573110 Label Location

TKR-751 FCC ID: ALH35573110 Display Component Side View Display Foil Side View TKR-751 FCC ID: ALH35573110 TX-RX A/2 Component Side View TX-RX A/2 Foil Side View TKR-751 FCC ID: ALH35573110 TX-RX B/2 Component Side View TX-RX B/2 Foil Side View TKR-751 FCC ID: ALH35573110 Final Component Side View Final Foil Side View

FCC ID: ALH35573110 Environmental Assessment for Mobiles/Fixed Base Station for FCC ID: FCC ID: ALH35573110 Model:TKR-751 to Federal Communications Commission 47 Cfr 1.1310 (MPE) Radiofrequency Radiation Exposure Limits Date Of Report: January 13, 2004 On the Behalf of the Applicant: Kenwood USA Corporation At the Request of: P.O. JB-F-006 Kenwood USA Corporation Communications Division 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Supervised By: Morton Flom, P. Eng. MFA p03c0006, d0410013 FCC ID: ALH35573110 Table of Contents Rule Description Page . Test Report 1 . Identification of the Equipment Under Test 2 . Standard Test Conditions and Engineering Practices 4 1.1310 Environmental Assessment 5 MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 1 of 7. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) Test Report (Supplemental) b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0410013 d) Client: Kenwood USA Corporation Communications Division 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 e) Identification: TKR-751 FCC ID: ALH35573110 Description: VHF FM Repeater f) EUT Condition: Not required unless specified in individual tests. g) Report Date: January 13, 2004 EUT Received: December 18, 2003 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 2 of 7. Identification of the Equipment Under Test (EUT) Name and Address of Applicant: Kenwood USA Corporation Communications Division 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 Manufacturer: Kenwood Electronics Technologies PTE Ltd. 1 Ang Mo Kio Street 63 Singapore 569110 FCC ID: ALH35573110 Model Number: TKR-751 Description: VHF FM Repeater Type of Emission: 16K0F3E, 11K0F3E Frequency Range, MHz: 146 to 174 Power Rating, Watts: 1 to 25 Switchable x Variable N/A Modulation: AMPS TDMA CDMA x OTHER Antenna: Helical Monopole Whip x Other Note: For RF Safety test antenna gain taken at the upper range of expected gain (i.e. 0 dBd) and RF Power set to highest nominal power across all channels. MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 3 of 7. M. Flom Associates, Inc. is accredited by the American Association for Laboratory Association (A2LA) as shown in the scope below. "This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this report have been determined in accordance with the laboratory's terms of accreditation unless stated otherwise in the report." Should this report contain any data for tests for which we are not accredited, or which have been undertaken by a subcontractor that is not A2LA accredited, such data would not covered by this laboratory's A2LA accreditation. MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 4 of 7. Standard Test Conditions and Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.4-1992/2000, section 6.1.9, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104 °F) unless the particular equipment requirements specify testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Prior to testing, the EUT was tuned up in accordance with the manufacturer's alignment procedures. All external gain controls were maintained at the position of maximum and/or optimum gain throughout the testing. Measurement results, unless otherwise noted, are worst-case measurements. MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 5 of 7. Name of Test: Environmental Assessment Specification: FCC: 47 CFR 1.1310 Measurement Guide: ANSI/IEEE C95.1 1992 Test Equipment: Maximum Permissible Exposure (MPE) measurement system, consisting of: Narda 8717-1174R, Radiation meter Narda 8761D, E-field probe (300 kHz – 3 GHz) (Calibrated Nov-98) Measurement Procedure: 1. The following measurements were performed with a Narda probe using ANSI/IEEE C95.1 as a guide. 2. Prior to making any measurements, the measurements system was calibrated in accordance with the manufacturer’s procedures. 3. The EUT’s radiating element (antenna) was placed on a 1 m tall table for ease of testing. For equipment normally operated on a metal surface, a ground plane was used. 4. The remaining equipment necessary to operate the EUT was maintained at a distance from the measurement arrangement suitable to minimize interference with the measurements. 5. The minimum safe distance was calculated from the formula Power Density = EIRP / 4πR 2 (Peak Watts/m 2 ). The calculation is shown with the measurement data. 6. With the EUT operating at maximum power, a search was initiated for worst case emissions with the probe raised and lowered over a range of 0.2 to 2 meters in height and over a horizontal plane of 0 o to 360 o . 7. Average values were calculated for the whole body (0.2- 2.0m), lower body (0.2-0.8m) and upper body (1.0-2.0m). Results: Attached. MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 6 of 7. Test Setup: Maximum Permissible Exposure (MPE) MFA p03c0006, d0410013 FCC ID: ALH35573110 Page Number 7 of 7. Name of Test: R.F. Radiation Exposure FCC Rules: 1.1307, 1.1310, 1.1311, 2.1091 Description, EUT: See page 2 of Test Report 0.3-3.0 MHz: Limit [ mW/cm 2 ] =…

Text truncated - open the document above for the full version.

FCC ID: ALH35573110 Page Number 18 of 52. AMENDED January 29, 2004 Name of Test: Field Strength of Spurious Radiation MFA p03c0006, d0410011