ALH36413110VHF FM Transceiver

KENWOOD CORPORATION FCC ID: ALH36413110/ALH36423110 INSTRUCTION MANUAL TK-2160/TK-3160-1 THANK YOU! We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. NOTICES TO THE USER WARNING: GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.). TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE STATIONS. SAFETY: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. WARNING: EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn off your transceiver while taking on fuel, or while parked in gasoline service stations. One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for technical assistance. KENWOOD CORPORATION FCC ID: ALH36413110/ALH36423110 ATTENTION (U.S.A. Only): The RBRC Recycle seal found on KENWOOD nickel-cadmium (Ni-Cd) battery packs indicates KENWOOD ’s voluntary participation in an industry program to collect and recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste streams, which is illegal in some areas. For information on Ni-Cd battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). KENWOOD ’s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Accessories Quantity Item Part Number K Instruction Manual B62 -1716 - *0 1 Belt Hook J29 –0701-05 1 Screw N35-3004-45 1 Cap B09 - 0676 - *3 1 Hardware Fixture J21 – 8464 - 04 1 KENWOOD CORPORATION FCC ID: ALH36413110/ALH36423110 Installing/ Removing the Optional Battery Pack PREPARATION The battery pack is not charged at the factory; charge it before use. CAUTION: DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED. AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER. IF THE CHARGER POWER IS RESET (TURNED ON AFTER BEING TURNED OFF), RECHARGING WILL START AGAIN AND THE BATTERY PACK WILL BECOME OVERCHARGED. DO NOT SHORT THE BATTERY TERMINALS OR DISPOSE OF THE BATTERY BY FIRE. NEVER ATTEMPT TO REMOVE THE CASING FROM THE BATTERY PACK. 1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver, then firmly press the battery pack t 2 Flip the safety catch into place to prevent accidentally pressing the release latch and removing the battery. 3 To remove the battery pack, lift the safety catch, press the release latch,then pull the battery pack away from the transceiver. KENWOOD CORPORATION FCC ID: ALH36413110/ALH36423110 Installing the Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Installing the Belt Clip 1 Remove the two screws from the rear of the transceiver, then remove the small, plastic black covering that was held in place. 2 Insert the belt clip mount into the space on the rear of the transceiver. 3 Using the 2 screws, affix the belt clip in place. Note: Do not dispose of the plastic black covering. If you remove the belt clip, replace the covering into the space on the rear of the transceiver. Either this covering or the belt clip must be in place, otherwise the battery pack may not remain installed properly. KENWOOD CORPORATION FCC ID: ALH36413110/ALH36423110 Installing the Cap over the Speaker/Microphone Jacks If you are not using an optional speaker/ microphone, install the cap over the SP/MIC jacks usi…

Text truncated - open the document above for the full version.

May 29, 2003 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Reference: This equipment meets the requirements of FCC Rules, Parts 90.203(e) and (g) as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel. E. Berger Staff Engineer Kenwood Communications Corporation Research & Development Department

5/29/2003 Federal Communications Commission EQUIPMENT APPROVAL SERVICES P.O. Box 358315 Pittsburgh, PA 15251-5315 Attention: Authorization and Evaluation Division Reference: FCC ID: ALH36413110 Model TK-2160 Dear Sir: Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of some of the information accompanying this Application, as listed below: Block Diagram Schematic Diagrams Circuit Description Parts List Active Devices Tuning Procedure These materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457 (d)(1)(ii), disclosure of the Application and all accompanying documentation will not be made before the date of Grant for the Application. Sincerely yours, Morton Flom, P. Eng., President M. Flom Associates, Inc. Agent for Applicant

The Modulation Limiting as shown on the referenced page does not exceed the limit. The test method (EIA/TIA603 2.2.3) requires that a 1000Hz modulating signal is applied to the transmitter and the level adjusted to obtain 60% of the full rated system deviation. In this case the maximum deviation is 2.5kHz therefore 60% is 1.5kHz. The level is then to be increased 20dB. At the increased level the input is varied between 300Hz and 3kHz and the modulation must remain between 60% and 100% of rated value. I have superimposed these reference points on one of the referenced plots. The plot extends beyond the limits of interest of the test. For input between 300Hz and 3kHz modulation must not be above rated value or below 60% of rated value 20dB level increase Point at which 1000Hz modulates at 60% rated value (1.5kHz)

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Bottom View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Front View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Left View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Rear View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Right View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Top View

Caution LabelFCC ID:ALH36413110 Model Name:TK-2160 Caution Label Label Location

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 Name Plate

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 PC Board Top View

ALH36413110 FCC ID:ALH36413110 Model Name:TK-2160 PC Board Bottom View

Test Report S/N: 042803-371ALH Test Date(s): May 05, 2003 FCC/IC SAR Evaluation © 2003 Celltech Labs Inc. 1 of 21 Celltech Labs Inc. declares under its sole responsibility that this device was found to be in compliance with the Specific Absorption Rate (SAR) RF exposure requirements specified in FCC 47 CFR §2.1093 and Health Canada’s Safety Code 6. The device was tested in accordance with the measurement standards and procedures specified in FCC OET Bulletin 65, Supplement C (Edition 01-01) and Industry Canada RSS-102 Issue 1 (Provisional) for the Occupational / Controlled Exposure environment. I attest to the accuracy of data. All measurements were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. This test report shall not be reproduced partially, or in full, without the prior written approval of Celltech Labs Inc. The results and statements contained in this report pertain only to the device(s) evaluated. Russell W. Pipe Senior Compliance Technologist Celltech Labs Inc. DECLARATION OF COMPLIANCE SAR EVALUATION Test Lab CELLTECH LABS INC. Testing and Engineering Lab 1955 Moss Court Kelowna, B.C. Canada V1Y 9L3 Phone: 250-448-7047 Fax: 250-448-7046 e-mail: [email protected] web site: www.celltechlabs.com Applicant Information KENWOOD USA CORPORATION 3975 John Creek Court, Suite 300 Suwanee, GA 30024 Rule Part(s): FCC 47 CFR §2.1093; IC RSS-102 Issue 1 (Provisional) Test Procedure(s): FCC OET Bulletin 65, Supplement C (01-01) FCC ID: ALH46413110 Model: TK-2160 EUT Type: Portable VHF PTT Radio Transceiver Modulation: FM (VHF) Tx Frequency Range: 136 - 174 MHz Max. RF Output Power Tested: 5.33 Watts (Conducted) Antenna P/N(s): KRA-26M3 (136-150 MHz) KRA-26M (146-162 MHz) KRA-26M2 (162-174 MHz) KRA-22M3 (136-150 MHz) KRA-22M (146-162 MHz) KRA-22M2 (162-174 MHz) KRA-25 (148-162 MHz) Battery Type(s): 7.2V NiMH, 2000mAh (P/N: KNB-26N) Body-Worn Accessories: Belt-Clip, Speaker-Microphone (P/N: KMC-17) Max. SAR Measured: 0.840 W/kg - Face-held (50% Duty Cycle) 0.895 W/kg - Body-worn (50% Duty Cycle) Test Report S/N: 042803-371ALH Test Date(s): May 05, 2003 FCC/IC SAR Evaluation © 2003 Celltech Labs Inc. 2 of 21 TABLE OF CONTENTS 1.0 INTRODUCTION..................................................................... 3 2.0 DESCRIPTION OF EUT............................................................ 3 3.0 SAR MEASUREMENT SYSTEM ............................................... 4 4.0 MEASUREMENT SUMMARY..................................................... 5 5.0 DETAILS OF SAR EVALUATION............................................... 6 6.0 EVALUATION PROCEDURES................................................... 6-7 7.0 SYSTEM PERFORMANCE CHECK............................................. 8 8.0 SIMULATED TISSUE MIXTURES............................................... 9 9.0 SAR LIMITS........................................................................... 9 10.0 SYSTEM SPECIFICATIONS...................................................... 10 11.0 PROBE SPECIFICATION......................................................... 11 12.0 PLANAR PHANTOM................................................................ 11 13.0 VALIDATION PHANTOM........................................................... 11 14.0 DEVICE HOLDER.................................................................... 11 15.0 TEST EQUIPMENT LIST........................................................... 12 16.0 MEASUREMENT UNCERTAINTIES............................................ 13-14 17.0 REFERENCES........................................................................ 15 APPENDIX A - SAR MEASUREMENT DATA............................................... 16 APPENDIX B - SYSTEM PERFORMANCE CHECK DATA............................ 17 APPENDIX C - SYSTEM VALIDATION PROCEDURES................................. 18 APPENDIX D - PROBE CALIBRATION...................................................... 19 APPENDIX E - MEASURED FLUID DIELECTRIC PARAMETERS................... 20 APPENDIX F - SAR TEST SETUP & EUT PHOTOGRAPHS.......................... 21 Test Report S/N: 042803-371ALH Test Date(s): May 05, 2003 FCC/IC SAR Evaluation © 2003 Celltech Labs Inc. Kenwood USA Corporation FCC ID: ALH46413110 3 of 21 Portable VHF PTT Radio Transceiver (136-174MHz) 1.0 INTRODUCTION This measurement report demonstrates compliance of the Kenwood USA Corp. Model: TK-2160 Portable VHF PTT Radio Transceiver FCC ID: ALH46413110 with the RF exposure requirements specified in FCC 47 CFR §2.1093 (see reference [1]) and Health Canada Safety Code 6 (see reference [2]) for the Occupational / Controlled Exposure environment. The test procedures described in FCC OET Bulletin 65, Supplement C (Edition 01-01) (see reference [3]) and IC RSS-102 Issue 1 (Provisional) (see reference [4]), were employed. A description of the product and operating configuration, detailed summary of the test results, methodology and procedures used in the evaluation, equipment used, and the various provisions of the rules are included within this test report. 2.0 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) FCC Rule Part(s) FCC 47 CFR §2.1093 IC Rule Part(s) RSS-102 Issue 1 (Provisional) Test Procedure(s) FCC OET Bulletin 65, Supplement C (Edition 01-01) Device Type Portable VHF PTT Radio Transceiver FCC ID ALH46413110 Model No. TK-2160 Serial No. Pre-production unit Modulation AMPS Tx Frequency Range 136 - 174 MHz Max. RF Output Power Tested 5.33 Watts (Conducted) Battery Type(s) 7.2V NiMH, 2000mAh (P/N: KNB-26N) Antenna Type(s) KRA-26M3 (136-150 MHz) Length: 168 mm KRA-26M (146-162 MHz) Length: 168 mm KRA-26M2 (162-174 MHz) Length: 168 mm KRA-22M3 (136-150 MHz) Length: 112 mm KRA-22M (146-162 MHz) Length: 112 mm KRA-22M2 (162-174 MHz) Length: 112 mm KRA-25 (148-162 MHz) Length: 252 mm Body-Worn Accessories Tested Belt-…

Text truncated - open the document above for the full version.

Test Report S/N: 042803-371ALH Test Date(s): May 05, 2003 FCC/IC SAR Evaluation © 2003 Celltech Labs Inc. Kenwood USA Corporation FCC ID: ALH46413110 17 of 21 Portable VHF PTT Radio Transceiver (136-174MHz) APPENDIX B - SYSTEM PERFORMANCE CHECK DATA System Performance Check - 300MHz Dipole Large Planar Phantom; Planar Section Probe: ET3DV6 - SN1387; ConvF(7.90,7.90,7.90); Crest factor: 1.0; 300 MHz Brain: σ = 0.89 mho/m ε r = 45.5 ρ = 1.00 g/cm 3 Cube 5x5x7: Peak: 1.29 mW/g, SAR (1g): 0.794 mW/g, SAR (10g): 0.520 mW/g, (Worst-case extrapolation) Penetration depth: 12.2 (10.2, 14.8) [mm]; Powerdrift: 0.02 dB Ambient Temp 23.3 °C; Fluid Temp 22.8 °C Forward Conducted Power: 250 mW Date Tested: May 05, 2003 SAR Tot [mW/g] 8.17E-2 1.63E-1 2.45E-1 3.27E-1 4.08E-1 4.90E-1 5.72E-1 6.54E-1 7.35E-1 8.17E-1 05/05/03 Celltech Labs Inc. Test Report S/N: 042803-371ALH Test Date(s): May 05, 2003 FCC/IC SAR Evaluation © 2003 Celltech Labs Inc. Kenwood USA Corporation FCC ID: ALH46413110 18 of 21 Portable VHF PTT Radio Transceiver (136-174MHz) APPENDIX C - SYSTEM VALIDATION Celltech Research Inc. 1955 Moss Court, Kelowna, B.C. Canada V1Y 9L3 Tel. 250-448-7047• Fax. 250-448-7046• e-mail: [email protected] www.celltechlabs.com 300MHz SYSTEM VALIDATION DIPOLE Type: Serial Number: Place of Calibration: Date of Calibration: Celltech Research Inc. hereby certifies that this device has been calibrated on the date indicated above. Calibrated by: Approved by: 300MHz Validation Dipole 135 Celltech Research Inc. October 15, 2002 1. Dipole Construction & Electrical Characteristics The validation dipole was constructed in accordance with the IEEE Std “Recommended Practice for Determining the Spatial-Peak Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques”. The electrical properties were measured using an HP 8753E Network Analyzer. The network analyzer was calibrated to the validation dipole N-type connector feed point using an HP85032E Type N calibration kit. The dipole was placed parallel to a planar phantom at a separation distance of 15.0mm from the simulating fluid using a loss-less dielectric spacer. The measured input impedance is: Feed point impedance at 300MHzRe{Z} = 47.639Ω Im{Z} = 0.5781Ω Return Loss at 300MHz-32.091dB Validation Dipole Dimensions Frequency (MHz)L (mm)h (mm)d (mm) 300420.0250.06.2 450288.0167.06.2 835161.0 89.83.6 900149.0 83.33.6 1450 89.1 51.73.6 1800 72.0 41.73.6 1900 68.0 39.53.6 2000 64.5 37.53.6 245051.8 30.63.6 300041.5 25.03.6 2. Validation Phantom The validation phantom was constructed using relatively low-loss tangent Plexiglas material. The dimensions of the phantom are as follows: Length: 83.5 cm Width:36.9 cm Height: 21.8 cm The bottom of the phantom is constructed of 6.2 ± 0.1mm Plexiglas. Dimensions of Plexiglas Planar Phantom 2.3 cm 83.5 cm 36.9 cm 99.7 cm 50 cm 19.5 cm 86 cm 0.5 cm 0.62 cm 39.3 cm 21.8 cm 300MHz System Validation Setup 300MHz System Validation Setup 3. Measurement Conditions The planar phantom was filled with brain simulating tissue having the following electrical parameters at 300MHz: Relative Permittivity:45.3 Conductivity:0.90 mho/m Ambient Temperature:23.3°C Fluid Temperature:23.0°C Fluid Depth:≥ 15cm The 300MHz simulating tissue consists of the following ingredients: IngredientPercentage by weight Water37.56% Sugar55.32% Salt5.95% HEC0.98% Dowicil 750.19% 300MHzTarget Dielectric Parameters at 22°C ε r = 45.3 σ = 0.87 S/m 4. SAR Measurement The SAR measurement was performed with the E-field probe in mechanical detection mode only. The setup and determination of the forward power into the dipole was performed using the following procedures. PM1 Att1 x Dipole 3D Probe positioner Flat Phantom Field probe Signal Generator AmpLow Pass 3dB Att3 Dir.Coupler Att2 PM2 Cable PM3 d First the power meter PM1 (including attenuator Att1) is connected to the cable to measure the forward power at the location of the dipole connector (X). The signal generator is adjusted for the desired forward power at the dipole connector (taking into account the attenuation of Att1) as read by power meter PM2. After connecting the cable to the dipole, the signal generator is readjusted for the same reading at power meter PM2. If the signal generator does not allow adjustment in 0.01dB steps, the remaining difference at PM2 must be taken into consideration. PM3 records the reflected power from the dipole to ensure that the value is not changed from the previous value. The reflected power should be 20dB below the forward power. Ten SAR measurements were performed in order to achieve repeatability and to establish an average target value. Validation Dipole SAR Test Results Validation Measurement SAR @ 0.25W Input averaged over 1g SAR @ 1W Input averaged over 1g SAR @ 0.25W Input averaged over 10g SAR @ 1W Input averaged over 10g Peak SAR @ 0.25W Input Test 10.7553.020.4961.981.21 Test 20.7573.030.4971.991.22 Test 30.7503.000.4931.971.21 Test 40.7633.050.5002.001.23 Test 50.7693.080.5052.021.24 Test 60.7553.020.4961.981.21 Test 70.7182.870.4721.891.16 Test 80.7302.920.4791.921.18 Test 90.7172.870.4711.881.15 Test100.7262.900.4771.911.17 Average Value0.7442.980.4881.951.20 The results have been normalized to 1W (forward power) into the dipole. Averaged over 1cm (1g) of tissue:2.98 mW/g Averaged over 10cm (10g) of tissue:1.95 mW/g Dipole 300 MHzFrequency: 300 MHz; Conducted Input Power: 250 [mW]Large Planar Phantom; Planar SectionProbe: ET3DV6 - SN1387; ConvF(8.00,8.00,8.00); Crest factor: 1.0; 300 MHz Brain: V = 0.9 0 mho/m H r = 45. 3 U = 1.00 g/cm 3 Cubes (10): Peak: 1.20 mW/g ± 0.16 dB, SAR (1g): 0.744 mW/g ± 0.15 dB, SAR (10g): 0.488 mW/g ± 0.15 dB, (Worst-case extrapo lation) Penetration depth: 12.3 (10.4, 14.7) [mm]; Powerdrift: 0.01 dB; Ambient Temp.: 23.3°C; Fluid Temp.: 23.0°C Calibration Date: October 15, 2002 SAR Tot [mW/g] 8.21E-21.64E-12.46E-13.28E-14.11E-14.93E-15.75E-16.57E-17.39E-18.21E-1 10/15/02Celltech R…

Text truncated - open the document above for the full version.

RADIO FREQUENCY ENERGY SAFETY INFORMATION _____ This KENWOOD transceiver has been tested and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute. • FCC OET Bulletin 65 Edition 97-01 Supplement C • American National Standards Institute (C95.1 – 1992) • American National Standards Institute (C95.3 – 1992) WARNING This KENWOOD transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric & Magnetic Energy) has the potential to cause slight thermal, or heating effects to any part of your body less than the recommended distance from this radio transmitter’s antenna. This means you can use the transceiver only if you are aware of the hazards of operating a transceiver and are familiar in ways to minimize these hazards. The transceiver has been designed for and is classified for Occupational Use Only. Occupational/ controlled exposure limits are applicable to situations in which persons are exposed to RF energy as a consequence of their employment, and such persons have been made aware of the potential for exposure and can exercise control over their exposure. This transceiver is not intended for use by the general public in uncontrolled environments. Uncontrolled environment exposure limits are applicable to situations in which the general public may be exposed to RF energy, or in which the persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. The following list provides you with the information required to ensure that you are aware of RF exposure and of how to operate this transceiver so that the FCC RF exposure limitations are not exceeded. • While transmitting (holding the PTT switch), always keep the antenna at least 3 cm (1 3/16 inches) from your body, as well as from any bystanders. • Do not transmit for more than 50% of the total transceiver use time; transmitting over 50% of the total use time may exceed the limits in accordance to the FCC RF exposure requirements. Nominal transceiver operation is 5% transmission time, 5% reception time, and 90% stand-by time. • Use only the specified antenna for this transceiver; this may be either the antenna provided with the transceiver or another antenna authorized by KENWOOD. Use only KENWOOD authorized accessories (antennas, battery packs, belt clips, etc.): When worn on the body, always place the radio in a KENWOOD recommended clip or carrying case meant for this product. The use of other than recommended or approved body- worn accessories may result in RF exposure levels which exceed the FCC’s occupational/ controlled environment RF exposure limits. CAUTION To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points. Electromagnetic Interference Compatibility Electronic devices are susceptible to electromagnetic interference (EMI) if they are not adequately shielded or designed for electromagnetic compatibility. Because this transceiver generates RF energy, it can cause interference to such equipment. • Turn OFF your transceiver where signs are posted to do so. Hospitals and health care facilities use equipment that is sensitive to electromagnetic radiation. • Turn OFF your transceiver while on board an aircraft when so instructed. Use of the transceiver must be in accordance with airline regulations and/or crew instructions. RADIO FREQUENCY SAFETY INFORMATION.doc 8/19/2003 © Kenwood U.S.A. Corp jeb

RADIO FREQUENCY ENERGY SAFETY INFORMATION _____ This KENWOOD transceiver has been tested and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute. • FCC OET Bulletin 65 Edition 97-01 Supplement C • American National Standards Institute (C95.1 – 1992) • American National Standards Institute (C95.3 – 1992) WARNING This KENWOOD transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric & Magnetic Energy) has the potential to cause slight thermal, or heating effects to any part of your body less than the recommended distance from this radio transmitter’s antenna. This means you can use the transceiver only if you are aware of the hazards of operating a transceiver and are familiar in ways to minimize these hazards. The transceiver has been designed for and is classified for Occupational Use Only. Occupational/ controlled exposure limits are applicable to situations in which persons are exposed to RF energy as a consequence of their employment, and such persons have been made aware of the potential for exposure and can exercise control over their exposure. This transceiver is not intended for use by the general public in uncontrolled environments. Uncontrolled environment exposure limits are applicable to situations in which the general public may be exposed to RF energy, or in which the persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. The following list provides you with the information required to ensure that you are aware of RF exposure and of how to operate this transceiver so that the FCC RF exposure limitations are not exceeded. • While transmitting (holding the PTT switch), always keep the antenna at least 3 cm (1 3/16 inches) from your body, as well as from any bystanders. • Do not transmit for more than 50% of the total transceiver use time; transmitting over 50% of the total use time may exceed the limits in accordance to the FCC RF exposure requirements. Nominal transceiver operation is 5% transmission time, 5% reception time, and 90% stand-by time. • Use only the specified antenna for this transceiver; this may be either the antenna provided with the transceiver or another antenna authorized by KENWOOD. Use only KENWOOD authorized accessories (antennas, battery packs, belt clips, etc.): When worn on the body, always place the radio in a KENWOOD recommended clip or carrying case meant for this product. The use of other than recommended or approved body- worn accessories may result in RF exposure levels which exceed the FCC’s occupational/ controlled environment RF exposure limits. CAUTION To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points. Electromagnetic Interference Compatibility Electronic devices are susceptible to electromagnetic interference (EMI) if they are not adequately shielded or designed for electromagnetic compatibility. Because this transceiver generates RF energy, it can cause interference to such equipment. • Turn OFF your transceiver where signs are posted to do so. Hospitals and health care facilities use equipment that is sensitive to electromagnetic radiation. • Turn OFF your transceiver while on board an aircraft when so instructed. Use of the transceiver must be in accordance with airline regulations and/or crew instructions. RADIO FREQUENCY SAFETY INFORMATION.doc 8/19/2003 © Kenwood U.S.A. Corp jeb

DRAFT DRAFT RADIO FREQUENCY ENERGY SAFETY INFORMATION _____ This KENWOOD transceiver has been tested and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute. • FCC OET Bulletin 65 Edition 97-01 Supplement C • American National Standards Institute (C95.1 – 1992) • American National Standards Institute (C95.3 – 1992) WARNING This KENWOOD transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric & Magnetic Energy) has the potential to cause slight thermal, or heating effects to any part of your body less than the recommended distance from this radio transmitter’s antenna. RF energy exposure is determined primarily by the distance to and the power of the transmitting device. In general, RF exposure is minimized when the lowest possible power is used or transmission time is kept to the minimum required for consistent communicatio…

Text truncated - open the document above for the full version.