ALH378400VHF Digital Transceiver

NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 INSTRUCTION MANUAL NX-200/300 TK-5220/5320 THANK YOU! We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. NOTICES TO THE USER WARNING: • GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. • ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. • REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. • DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.). • TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE STATIONS. SAFETY: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. WARNING: EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn off your transceiver while taking on fuel, or while parked in gasoline service stations. One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer for technical assistance. NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 ATTENTION (U.S.A. Only): The RBRC Recycle seal found on KENWOOD nickel-cadmium (Ni-Cd) battery packs indicates KENWOOD’s voluntary participation in an industry program to collect and recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste streams, which is illegal in some areas. For information on Ni-Cd battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). KENWOOD’s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. § Accessories Quantity Item Part Number K Belt Clip J29 - 0730 -*5 1 Screw N30 - 3008 - 60 2 Cap B09 - 0717 - *3 1 Screw N08 - 0564 - *4 1 NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 Installing/ Removing the Optional Battery Pack PREPARATION The battery pack is not charged at the factory; charge it before use. CAUTION: • DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE HE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED. • AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER. IF THE CHARGER POWER IS RESET (TURNED ON AFTER BEING TURNED OFF), RECHARGING WILL START AGAIN AND THE BATTERY PACK WILL BECOME OVERCHARGED. • DO NOT SHORT THE BATTERY TERMINALS OR DISPOSE OF THE BATTERY BY FIRE. • NEVER ATTEMPT TO REMOVE THE CASING FROM THE BATTERY PACK. 1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver, then firmly press the battery pack t 2 Flip the safety catch into place to prevent accidentally pressing the release latch and removing the battery. 3 To remove the battery pack, lift the safety catch, press the release latch,then pull the battery pack away from the transceiver. NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 Installing the Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Installing the Belt Clip If necessary, attach the belt clip using the two supplied 3 x 6 mm screws. Notes: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 Installing the Cap over the Speaker/Microphone Jacks If you are not using an optional KMC-25 speaker/ microphone, install the cover over the univeral connector using the supplied 4 x 6 mm screw. Installing the Optional Speaker/ Microphone 1 Insert the guide of the speaker/ microphone connector into the groove of the universalconn…

Text truncated - open the document above for the full version.

Attestation_FCC Part 90 7.10.07 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Gentlemen: Reference: ALH378400, NX-200 K, K2 & TK-5220 K, K2 This equipment meets the requirements of the FCC Rules, Parts 90.203(e) and (g), as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely. Kenwood USA Corporation Joel E. Berger Joel Berger, Engineer

June 20, 2007 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Gentlemen: This letter will authorize the appointment of FLOM TEST LAB to act as our Agent in all FCC matters. This appointment is affective until otherwise notified by us. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The Applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 USC 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. Kenwood USA Corporation Joel Berger

June 27, 2007 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: NX-200-K, NX-200-K2, TK-5220-K and TK-5220-K2, FCC ID: ALH378400 To Whom It May Concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, Active Devices and Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that should never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Joel Berger

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 May 12-16, 2003 ¾TCB Training Course - Columbia, MD Session 3a Slide 23 Bessel Function Analysis July 2, 2007 RE: Kenwood USA Corporation FCC ID: ALH378400 After a review of the submitted information, I have a few comments on the above referenced Application. Depending on your responses, kindly understand there may be additional comments. 1) For internal photographs, only a few photos of circuit boards were provided. Part 2.1033(b)(12) cites photos should include: “sufficient views of the internal construction to define component placement and chassis assembly.” (i.e. showing placement of boards in the chassis, shields present, etc.). Typically a few additional photographs are show with the case opened and in such a way to show internal layout/construction. Please provide additional photographs as necessary.” 2) Please note that IC requires 3 items on the label, (model, applicant, and Certification No. as Certified). Devices not properly labeled are not considered Certified. The model number on the label does not appear to match the model number(s) being certified. By placing the information on 2 lines is misleading and uncertain as to the actual complete model number. Please review/correct. 3) Limits for spurious emissions are not correctly calculated. Information on page 16 (labeled 4 of 28) of the report shows: 43 + 10 log (37) = 58.68 dB 43 + 10 log (36.8) = 58.65 dB Note that this equation is not utilized properly. The equation expects conducted power to be in Watts (i.e. see 90.210). This yields: 43 + 10 log (5.0119) = 50 dB 43 + 10 log (1.230) = 43.9 dB This affects presentation of data throughout the report. Please correct. 4) Radiated spurious emissions must follow substitution methods as specified by EIA/TIA 603. A test measurement procedure was not provided for this data nor reference to procedure used. Please update the report. 5) Regarding occupied bandwidth, normally a second trace is shown that shows that the top grat. line to show that the 0 dB reference is appropriately set to the total unmodulated carrier power (P). Please confirm or correct as necessary. As an example, note both traces for the following from FCC training: z Page 2 July 2, 2007 6) FYI...It does not appear that the least stringent masks were applied in cases where the limites are attenuated based on 10 log (P). However device still appears to show compliance. 7) For IC, kindly explain which bandwidths utilize which modulations so that REL listing and certificate can be properly done. IC form simply sites 3 types of modulations. Ideally a complete list of emissions designators like on the 731 form should be provided (utilizing appropriate 99% bandwidths). 8) Please update the modulation limiting plots with higher resolution or provide separate pages of higher resolution. 9) Modulation limiting should be supplied for 12.5 kHz. Please provide. 10) It is unsure if this device uses scrambling techniques and subject to 90.212. Additionally, typically bandwidth plots should be provided for both normal and scrambled modes if relevant. 11) Pages 42-43 (labeled 27 – 28 of 28) does not appear to match the 731 form for 8KXX emissions. On the 731 some are 8K10 or 8K30, while the report is citing 8K0 or 8K1 for different designators. This information should be consistent. Please correct. 12) Use of this type of device under Part 74 is unusual. Please explain compliance and use under Part 74. Additionally, it would appear that only 74 subpart D would possibly apply. 74E doesn’t cover the appropriate frequencies and devices exceeds 74H power limitations. 13) Part 74 does not appear to allow F7W emissions. Additionally per 74.462 – it appears only a few emissions designators may apply for Part 74. Please comment and explain which emissions designators are requested for Part 74. 14) 90.203 attestation listed in report was not found. Please provide. 15) The current version of RSS-119 is Issue 9, issued in June 2007. Please review and ensure the device meets this new version. Additionally, please update the IC form for the proper version. 16) Operational description cites 136 – 174 MHz. IC form cites 138 – 174 MHz. Please explain compliance to RSS-119, section 3.4. 17) Because the Test report itself does not cover RSS-119, even if the requirements are the same – a cross reference showing appropriate FCC sections compared to IC sections should be provided. See following page as an example. Note there are additions in RSS-119 not covered by the report. 18) RX spurious emissions (RSS-119 section 5.11) do not appear to have been provided. Please provide. 19) The connector appears to contain capability of serial connection. Please explain if this is intended for this device to be able to be used as a data-modem. Note that there are many specific requirements under RSS-119 for data-modems which appear to not have been provided. 20) For tests such as power, spurious, etc., it does not appear that RSS-GEN 4.3(g) was followed. Please review/correct. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender. z Page 3 July 2, 2007

From: Jackie Pillai <[email protected]> Subject: Kenwood ALH378400 ATCB005114 To: Tim Johnson <[email protected]> Dear Tim, In response to your questions: 1. Client has been submitting these types of photos for all previous applications. Client has been advised that, in the future, he provides more photos. 2. Client has been submitting same type of label for years. Unless there are new IC requirements, there is no need to change them. 3. See revised report - uploaded. 4. See revised report - uploaded. 5. See revised report - uploaded. 6. Is an FYI only. 7. See revised IC application. 8. See revised report - uploaded. 9. See revised report - uploaded. 10. No, the device does not use any scrambling techniques. 11. Form 731 is correct, typo in test report corrected. See revised report - uploaded. 12. Client has been submitting applications for years using these rules sections. 13. Same answer as #12. 14. 90.203 attestation uploaded. 15. Cross reference uploaded. 16. User programming is not accessible. See exhibit from #14. 17. Cross reference uploaded. 18. Waiting for TCB response. 19. Device connector is not used as a data modem. 20. Waiting for TCB response. If you have any questions, please feel free to contact us. Regards, Jackie Pillai Administration Phone: (480) 926-3100 Confidential - The information in this message is only intended for the person(s) or organization(s) to whom it is addressed. If you are not that person, please contact the sender, and destroy this copy.

NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400 NX-200-K, NX-200-K2, TK-5220-K, TK-5220-K2 FCC ID: ALH378400 IC: 282D-378400

Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Date: June 26, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: NX-200 FCC ID: ALH378400 FCC Rules: 22,74,90 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab Director enclosure(s) cc: Applicant HSB/je Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Date: June 26, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: NX-200 FCC ID: ALH378400 FCC Rules: 22,74,90 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown i.e.: a) Application Form b) Test Report (if applicable) c) Filing Fees d) Copy of Original Grant e) Photos (if applicable) f) Label Drawing (if changes have been made) We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab Director enclosure(s) cc: Applicant HSB/je Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Transmitter Certification of FCC ID: ALH378400 Model: NX-200 to Federal Communications Commission Rule Part(s) 22,74,90 Date of report: June 26, 2007 On the Behalf of the Applicant: Kenwood USA Corporation At the Request of: Kenwood USA Corporation Communications Division 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Supervised by: Hoosamuddin S. Bandukwala, Lab Director Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 List of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: Kenwood USA Corporation FCC ID: ALH378400 By Applicant: 1. Letter of Authorization 2. Confidentiality Request: 0.457 And 0.459 3. Part 90.203(e) & (g) Attestation 4. Identification Drawings, 2.1033(c)(11) Label Location of Label Compliance Statement Location of Compliance Statement 5. Photographs, 2.1033(c)(12) 6. Documentation: 2.1033(c) (3) User Manual (9) Tune Up Info (10) Schematic Diagram (10) Circuit Description Block Diagram Parts List Active Devices 7. MPE/SAR Report By M.F.A. Inc.: A. Testimonial & Statement of Certification Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 The Applicant has been cautioned as to the following: 15.21 Information to the User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Table of Contents Rule Description Page 2.1033(c)(14) Rule Summary 2 . Standard Test Conditions and Engineering Practices 3 2.1033(c) General Information Required 4 2.1046(a) Carrier Output Power (Conducted) 6 2.1046(a) ERP Carrier Power (Radiated) 8 2.1051 Unwanted Emissions (Transmitter Conducted) 10 2.1053(a) Field Strength of Spurious Radiation 14 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 18 99% Bandwidth 21 90.214 Transient Frequency Behavior 24 2.1047(a) Audio Low Pass Filter (Voice Input) 29 2.1047(a) Audio Frequency Response 31 2.1047(b) Modulation Limiting 33 2.1055(a)(1) Frequency Stability (Temperature Variation) 37 2.1055(b)(1) Frequency Stability (Voltage Variation) 39 Flom Test Labs 3356 North San Marcos Place, Suite 107 Page 1 of 42 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Required …

Text truncated - open the document above for the full version.

Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Date: June 26, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: NX-200 FCC ID: ALH378400 FCC Rules: 22,74,90 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab Director enclosure(s) cc: Applicant HSB/je Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Date: June 26, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: NX-200 FCC ID: ALH378400 FCC Rules: 22,74,90 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown i.e.: a) Application Form b) Test Report (if applicable) c) Filing Fees d) Copy of Original Grant e) Photos (if applicable) f) Label Drawing (if changes have been made) We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab Director enclosure(s) cc: Applicant HSB/je Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Transmitter Certification of FCC ID: ALH378400 Model: NX-200 to Federal Communications Commission Rule Part(s) 22,74,90 Date of report: June 26, 2007 On the Behalf of the Applicant: Kenwood USA Corporation At the Request of: Kenwood USA Corporation Communications Division 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Supervised by: Hoosamuddin S. Bandukwala, Lab Director Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 List of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: Kenwood USA Corporation FCC ID: ALH378400 By Applicant: 1. Letter of Authorization 2. Confidentiality Request: 0.457 And 0.459 3. Part 90.203(e) & (g) Attestation 4. Identification Drawings, 2.1033(c)(11) Label Location of Label Compliance Statement Location of Compliance Statement 5. Photographs, 2.1033(c)(12) 6. Documentation: 2.1033(c) (3) User Manual (9) Tune Up Info (10) Schematic Diagram (10) Circuit Description Block Diagram Parts List Active Devices 7. MPE/SAR Report By M.F.A. Inc.: A. Testimonial & Statement of Certification Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 The Applicant has been cautioned as to the following: 15.21 Information to the User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Flom Test Labs 3356 North San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Table of Contents Rule Description Page 2.1033(c)(14) Rule Summary 2 . Standard Test Conditions and Engineering Practices 3 2.1033(c) General Information Required 4 2.1046(a) Carrier Output Power (Conducted) 6 2.1046(a) ERP Carrier Power (Radiated) 8 2.1051 Unwanted Emissions (Transmitter Conducted) 10 2.1053(a) Field Strength of Spurious Radiation 19 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 23 99% Bandwidth 26 90.214 Transient Frequency Behavior 29 2.1047(a) Audio Low Pass Filter (Voice Input) 34 2.1047(a) Audio Frequency Response 36 2.1047(b) Modulation Limiting 38 2.1055(a)(1) Frequency Stability (Temperature Variation) 42 2.1055(b)(1) Frequency Stability (Voltage Variation) 44 Flom Test Labs 3356 North San Marcos Place, Suite 107 Page 1 of 47 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax MFA p0750001, d0760027 Required …

Text truncated - open the document above for the full version.