ALH415000VHF FM Transceiver

© B62-2182-00 (K, K2) 09 08 07 06 05 04 03 02 01 00 INSTRUCTION MANUAL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-2360/ TK-3360  Thank You We are grateful you have chosen Kenwood for your land moble rado applcatons. noTices To The user ◆ Government law prohbts the operaton of unlcensed rado transmtters wthn the terrtores under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. SAFETY: It s mportant that the operator s aware of and understands hazards common to the operaton of any transcever. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memores are reserved for Kenwood Corporaton.  One or more of the following statements may be applicable: FCC WARNING Ths equpment generates or uses rado frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the nstructon manual. The user could lose the authorty to operate ths equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC Ths equpment has been tested and found to comply wth the lmts for a Class B dgtal devce, pursuant to Part 15 of the FCC Rules. These lmts are desgned to provde reasonable protecton aganst harmful nterference n a resdental nstallaton. Ths equpment generates, uses and can generate rado frequency energy and, f not nstalled and used n accordance wth the nstructons, may cause harmful nterference to rado communcatons. However, there s no guarantee that the nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recepton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the followng measures: • Reorent or relocate the recevng antenna. • Increase the separaton between the equpment and recever. • Connect the equpment to an outlet on a crcut dfferent from that to whch the recever s connected. • Consult the dealer for techncal assstance.  The RBRC Recycle seal found on Kenwood nckel metal hydrde (N-MH) battery packs ndcates Kenwood’s voluntary partcpaton n an ndustry program to collect and recycle N-MH batteres after their operating life has expired. The RBRC program s an alternatve to dsposng N-MH batteres wth your regular refuse or n muncpal waste streams, whch s llegal n some areas. For nformaton on N-MH battery recyclng n your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s nvolvement n ths program s part of our commtment to preserve our envronment and conserve our natural resources. The RBRC Recycle seal found on Kenwood lthum-on (L-on) battery packs ndcates Kenwood’s voluntary partcpaton n an ndustry program to collect and recycle L-on batteres after their operating life has expired. The RBRC program s an alternatve to dsposng L-on batteres wth your regular refuse or n muncpal waste streams, whch s llegal n some areas. For nformaton on L-on battery recyclng n your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s nvolvement n ths program s part of our commtment to preserve our envronment and conserve our natural resources. v PrecauTions • Do not charge the transcever and battery pack when they are wet. • Ensure that there are no metallc tems located between the transcever and the battery pack. • Do not use options not specified by Kenwood. • If the de-cast chasss or other transcever part s damaged, do not touch the damaged parts. • If a headset or headphone s connected to the transcever, reduce the transcever volume. Pay attenton to the volume level when turnng the squelch off. • Do not place the mcrophone cable around your neck whle near machnery that may catch the cable. • Do not place the transcever on unstable surfaces. • Ensure that the end of the antenna does not touch your eyes. • When the transcever s used for transmsson for many hours, the radator and chasss wll become hot. Do not touch these locatons when replacng the battery pack. • Always swtch the transcever power off before nstallng optonal accessores. • The charger s the devce that dsconnects the unt from the AC mans lne. The AC plug should be readly accessble. v • Do not dsassemble or modfy the transcever for any reason. • Do not place the transcever on or near arbag equpment whle the vehicle is running. When the airbag inflates, the transceiver may be ejected and strke the drver or passengers. • Do not transmt whle touchng the antenna termnal or f any metallic parts are exposed from the antenna covering. Transmttng at such a tme may result n a hgh-frequency burn. • If an abnormal odor or smoke s detected comng from the transcever, swtch the transcever power off mmedately, remove the battery pack from the transcever, and contact your Kenwood dealer. • Use of the transcever whle you are drvng may be aganst traffic laws. Please check and observe the vehicle regulations n your area. • Do not expose the transceiver to extremely hot or cold condtons. • Do not carry the battery pack (or battery case) wth metal objects, as they may short the battery termnals. • Danger of explosion if the battery is incorrectly replaced; replace only wth the same type. Turn the transcever power off n the followng locatons: • Near blastng stes. • In arplanes. (Any use of the transcever must follow the nstructons and regulatons provded by the arlne crew.) • Where restrctons or warnngs are posted regardng the use of rado devces, ncludng but not lmted to medcal facltes. • Near persons usng pacemakers. v informaTion concerning The baTTerY Pack The batte…

Text truncated - open the document above for the full version.

January 25, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer Subject: Justify Extended Frequency Range for MODEL: TK-2360-K, TK-2360-M, FCC ID: ALH415000. To Whom It May Concern: This letter serves justification for extended frequencies This device has design capability to operate in the frequency band 150 to 174 MHz and complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transit frequencies using the normally accessible external controls. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of Kenwood approved Service Agents. In addition to Part 90 usage, this device is utilized in systems such as Federal and Public Safety agencies, e.g. police, fire, and emergency medical, etc. as indicated in the following table: Table 1 – Frequency Range and Rule Parts - (47 CFR Part 2.106) It is understood that a grant note code may be added to the grant, which indicates this required operation. Please contact me if you require any additional information. Sincerely, Freq. Range (MHz) Part 90 Federal Customers 150.0000-150.8000 x 150.8000-156.2475 x 156.2475-157.0375 x 157.0375-161.5750 x 161.5750-161.7750 x 161.7750-173.4000 x 173.4000-174.0000 x

TK-2360-K, TK-2360-M FCC ID: ALH415000 Front View Rear View TK-2360-K, TK-2360-M FCC ID: ALH415000 Left View Right View TK-2360-K, TK-2360-M FCC ID: ALH415000 Top View Bottom View

TK-2360-K, TK-2360-M FCC ID: ALH415000 TK-2360-K TK-2360-M

TK-2360-K, TK-2360-M FCC ID: ALH415000 Component Side View TK-2360-K, TK-2360-M FCC ID: ALH415000 Foil Side View TK-2360-K, TK-2360-M FCC ID: ALH415000 TK-2360-K, TK-2360-M FCC ID: ALH415000 Component Side View Foil Side View

Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 Date: October 13, 2009 Applicant: Kenwood USA Corporation Communications Division 3970 Johns Creek Court, Suite 100 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Equipment: TK-2360-K, TK-2360-M FCC ID: ALH415000 FCC Rules: Part 90 Gentlemen: Enclosed please find your copy of the Engineering Test Report for which you are subject to the restrictions as listed on the attached summary. Once a Telecommunication Certification Body (TCB) issues a Grant the Federal Communication Commission (FCC) has 30 days to review the application and request added information. It is your decision whether or not to market the equipment subject to a possible recall before the end of the 30 days. If your equipment is still retained by us, it will be returned to you 30 days after approval is achieved. Our invoice for services has been directed to your Accounts Payable Department. For any additional information please contact us. Thank you. Sincerely yours, John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 Summary of Restrictions 1. All submissions to the FCC are subject to their Examiner's interpretation. 2. Please allow from 60 to 90 days before hearing from the FCC with regard to any submission. 3. The FCC can set aside any action; modify or set aside any action, within 30 days. (FCC Rule 1.108, 1.113). 4. Under Rule 2.803, if device is not type accepted/certificated then it must not be sold, leased, offered for sale, imported, shipped or distributed or advertised for sale. 5. FCC can revoke its certificates at any time if the equipment does not meet or continue to meet their Rules. (Rule Parts 2.927, 2.939). 6. FCC can request a sample at any time (2.936). Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 Date: October 13, 2009 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: TK-2360-K, TK-2360-M FCC ID: ALH415000 FCC Rules: Part 90 Dear Gentleman: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Best regards, John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 Test Report for Model: TK-2360-K, TK-2360-M to Federal Communications Commission Rule Part 90 Date of report: October 13, 2009 On the Behalf of the Applicant: Kenwood USA Corporation At the Request of: Kenwood USA Corporation Communications Division 3970 Johns Creek Court, Suite 100 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Reviewed by: John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 Test Report Revision History Revision Date Revised By Reason for revision 1.0 11/13/2009 G. Corbin Original Document 2.0 12/24/2009 G. Corbin Updated Radiated Spurious Tables, pg 15-16 3.0 03/03/2010 G. Corbin Added dBm to Output Power table, pg 8 Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 List of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: Kenwood USA Corporation FCC ID: ALH415000 By Applicant: 1. Letter of Authorization 2. Confidentiality Request: 0.457 And 0.459 3. Identification Drawings, 2.1033(c)(11) Label Location of Label Compliance Statement Location of Compliance Statement 4. Photographs, 2.1033(c)(12) 5. Documentation: 2.1033(c) (3) User Manual (9) Tune Up Info (10) Schematic Diagram (10) Circuit Description Block Diagram Parts List Active Devices 6. MPE/SAR Report By Compliance Testing: A. Testimonial & Statement of Certification Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970013, d09a0005 Rev 3.0 The Applicant has been cautioned as to the following: 15.21 Information to the User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, s…

Text truncated - open the document above for the full version.

Page 1 of 3 Test Setup Photos: Kenwood USA – TK-2360-K, TK-2360-M Conducted Output Power Conducted Spurious Page 2 of 3 Emissions Mask Radiated Output Power Page 3 of 3 Radiated Output Power #2