ALH415100UHF FM TRANSCEIVER

© B62-2182-00 (K, K2) 09 08 07 06 05 04 03 02 01 00 INSTRUCTION MANUAL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-2360/ TK-3360  Thank You We are grateful you have chosen Kenwood for your land moble rado applcatons. noTices To The user ◆ Government law prohbts the operaton of unlcensed rado transmtters wthn the terrtores under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. SAFETY: It s mportant that the operator s aware of and understands hazards common to the operaton of any transcever. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memores are reserved for Kenwood Corporaton.  One or more of the following statements may be applicable: FCC WARNING Ths equpment generates or uses rado frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the nstructon manual. The user could lose the authorty to operate ths equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC Ths equpment has been tested and found to comply wth the lmts for a Class B dgtal devce, pursuant to Part 15 of the FCC Rules. These lmts are desgned to provde reasonable protecton aganst harmful nterference n a resdental nstallaton. Ths equpment generates, uses and can generate rado frequency energy and, f not nstalled and used n accordance wth the nstructons, may cause harmful nterference to rado communcatons. However, there s no guarantee that the nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recepton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the followng measures: • Reorent or relocate the recevng antenna. • Increase the separaton between the equpment and recever. • Connect the equpment to an outlet on a crcut dfferent from that to whch the recever s connected. • Consult the dealer for techncal assstance.  The RBRC Recycle seal found on Kenwood nckel metal hydrde (N-MH) battery packs ndcates Kenwood’s voluntary partcpaton n an ndustry program to collect and recycle N-MH batteres after their operating life has expired. The RBRC program s an alternatve to dsposng N-MH batteres wth your regular refuse or n muncpal waste streams, whch s llegal n some areas. For nformaton on N-MH battery recyclng n your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s nvolvement n ths program s part of our commtment to preserve our envronment and conserve our natural resources. The RBRC Recycle seal found on Kenwood lthum-on (L-on) battery packs ndcates Kenwood’s voluntary partcpaton n an ndustry program to collect and recycle L-on batteres after their operating life has expired. The RBRC program s an alternatve to dsposng L-on batteres wth your regular refuse or n muncpal waste streams, whch s llegal n some areas. For nformaton on L-on battery recyclng n your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s nvolvement n ths program s part of our commtment to preserve our envronment and conserve our natural resources. v PrecauTions • Do not charge the transcever and battery pack when they are wet. • Ensure that there are no metallc tems located between the transcever and the battery pack. • Do not use options not specified by Kenwood. • If the de-cast chasss or other transcever part s damaged, do not touch the damaged parts. • If a headset or headphone s connected to the transcever, reduce the transcever volume. Pay attenton to the volume level when turnng the squelch off. • Do not place the mcrophone cable around your neck whle near machnery that may catch the cable. • Do not place the transcever on unstable surfaces. • Ensure that the end of the antenna does not touch your eyes. • When the transcever s used for transmsson for many hours, the radator and chasss wll become hot. Do not touch these locatons when replacng the battery pack. • Always swtch the transcever power off before nstallng optonal accessores. • The charger s the devce that dsconnects the unt from the AC mans lne. The AC plug should be readly accessble. v • Do not dsassemble or modfy the transcever for any reason. • Do not place the transcever on or near arbag equpment whle the vehicle is running. When the airbag inflates, the transceiver may be ejected and strke the drver or passengers. • Do not transmt whle touchng the antenna termnal or f any metallic parts are exposed from the antenna covering. Transmttng at such a tme may result n a hgh-frequency burn. • If an abnormal odor or smoke s detected comng from the transcever, swtch the transcever power off mmedately, remove the battery pack from the transcever, and contact your Kenwood dealer. • Use of the transcever whle you are drvng may be aganst traffic laws. Please check and observe the vehicle regulations n your area. • Do not expose the transceiver to extremely hot or cold condtons. • Do not carry the battery pack (or battery case) wth metal objects, as they may short the battery termnals. • Danger of explosion if the battery is incorrectly replaced; replace only wth the same type. Turn the transcever power off n the followng locatons: • Near blastng stes. • In arplanes. (Any use of the transcever must follow the nstructons and regulatons provded by the arlne crew.) • Where restrctons or warnngs are posted regardng the use of rado devces, ncludng but not lmted to medcal facltes. • Near persons usng pacemakers. v informaTion concerning The baTTerY Pack The batte…

Text truncated - open the document above for the full version.

Radio FRequency eneRgy SaFety inFoRmation This Kenwood transceiver has been tested and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute. • FCC OET Bulletin 65 Edition 97-01 Supplement C • American National Standards Institute (C95.1 – 1992) • American National Standards Institute (C95.3 – 1992) This Kenwood transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric & Magnetic Energy) has the potential to cause slight thermal, or heating effects to any part of your body less than the recommended distance from this radio transmitter’s antenna. RF energy exposure is determined primarily by the distance to and the power of the transmitting device. In general, RF exposure is minimized when the lowest possible power is used or transmission time is kept to the minimum required for consistent communications, and the greatest distance possible from the antenna to the body is maintained. The transceiver has been designed for and is classified for Occupational Use Only. Occupational/ controlled exposure limits are applicable to situations in which persons are exposed to RF energy as a consequence of their employment, and such persons have been made aware of the potential for exposure and can exercise control over their exposure. This means you can use the transceiver only if you are aware of the potential hazards of operating a transceiver and are familiar in ways to minimize these hazards. This transceiver is not intended for use by the general public in uncontrolled environments. Uncontrolled environment exposure limits are applicable to situations in which the general public may be exposed to RF energy, or in which the persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. The following list provides you with the information required to ensure that you are aware of RF exposure and of how to operate this transceiver so that the FCC RF exposure limitations are not exceeded. • While transmitting (holding the PTT switch or speaking with VOX enabled), always keep the antenna and the radio at least 3 cm (1 3/16 inches) from your body or face, as well as from any bystanders. A LED on the top of the radio shows red when the transmitter is operating in both PTT and VOX modes. • Do not transmit for more than 50% of the total transceiver use time; transmitting over 50% of the total use time may exceed the limits in accordance to the FCC RF exposure requirements. Nominal transceiver operation is 5% transmission time, 5% reception time, and 90% stand-by time. • Use only the specified antenna for this transceiver; this may be either the antenna provided with the transceiver or another antenna authorized by Kenwood . Use only Kenwood authorized accessories (antennas, battery packs, belt clips, Speaker/ Mics or headsets etc.): When worn on the body, always place the radio in a Kenwood recommended clip or carrying case meant for this product. The use of other than recommended or approved body- worn accessories may result in RF exposure levels which exceed the FCC’s occupational/ controlled environment RF exposure limits. To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points. Electromagnetic Interference Compatibility Electronic devices are susceptible to electromagnetic interference (EMI) if they are not adequately shielded or designed for electromagnetic compatibility. Because this transceiver generates RF energy, it can cause interference to such equipment. • Turn OFF your transceiver where signs are posted to do so. Hospitals and health care facilities use equipment that is sensitive to electromagnetic radiation. • Turn OFF your transceiver while on board an aircraft when so instructed. Use of the transceiver must be in accordance with airline regulations and/or crew instructions. B59-2546-00

October 28, 2009 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer Subject: Justify Extended Frequency Range for MODEL: TK-3360-K, TK-3360-X, FCC ID: ALH415100. To Whom It May Concern: This letter serves justification for extended frequencies This device has design capability to operate in the frequency band 450 to 512 MHz and complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transit frequencies using the normally accessible external controls. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of Kenwood approved Service Agents. In addition to Part 90 usage, this device is utilized in systems such as Federal and Public Safety agencies, e.g. police, fire, and emergency medical, etc. as indicated in the following table: Table 1 – Frequency Range and Rule Parts - (47 CFR Part 2.106) It is understood that a grant note code may be added to the grant which indicates this required operation. Please contact me if you require any additional information. Sincerely, Freq. Range (MHz) Part 90 Federal Customers 450.0000-454.0000 x 454.0000-456.0000 x 456.0000-462.5375 x 462.5375-462.7375 x 462.7375-467.5375 x 467.5375-467.7375 x 467.7375-512.0000 x

Page 1 of 2 FCC ID: ALH415100 – Kenwood (TCB-p0970014) Date: February 18, 2010 To: Steve Schafer - [email protected] From: Tim Harrington - [email protected] Correspondence Ref Number: 81357 Form 731 Confirmation Number: TC765740 Response noted: Blue lettering is from John Erhard, Engineering Manager for Compliance Testing Red lettering is from Jon Hughes, Project Manager for Celltech 1) Per 2.962(f)(1), applications processed by TCB must be in accordance with FCC rules, policies, and procedures. For this filing, the line-entry part 90-frequency listings encompass frequencies not authorized for part 90 - therefore filing does not appear to be in accordance with KDB pub. 634817. Please explain and/or revise all applicable parts of filing where appropriate. The frequency band of this device does encompass small sections of bands that are available for use by and subject to other rule sections, however this application is for Part 90 only and the final sale and licensing of these radios will be under that rule section as stated on the grant and application. 2) Basic SAR evaluation considerations for PTT portable devices: a) SAR evaluations must address all device configuration options including all antennas, body-worn accessories, audio accessories, batteries, for each transmission band of all antenna options. See also KDB 447498 item 6). b) Note that the majority of procedures in OET B 65 Supplement C 01-01, especially Appendix D, are intended for cellphone SAR evaluations; similar considerations for test reduction based on SAR levels are available in KDB 447498 item 1) for certain other device configurations. These types of test reductions are applicable only for full and complete device test conditions, without application of other types of test reductions such as under KDB 447498 item 6) or certain similar reductions described in other KDB publications for specific devices. c) Provisions for "a priori" omitting some transmission-band channels for each antenna based on initial tests for the mid-band (and/or highest output) channel, have not been established for higher-output devices using mid-band and reduced testing of multiple accessory combinations and configurations; KDB 447498 item 1) e) i), for example, is not directly applicable for devices operating under higher occupational exposure limits. Reduction of number of test channels on top of reduction for certain accessory configurations requires beforehand FCC test plan approval; requests for such consideration must clearly explain device and configuration details and proposed subset of tests relative to full test requirements matrix. d) For belt-clips and/or body-worn accessories having a body-facing surface that is not parallel with main enclosure of the device, and/or having features or protrusions causing relative tilt of device housing and/or antenna, filing must clearly document all spacings to phantom / body along length of device, and provide details and rational how and why SAR positions hold either enclosure parallel to phantom, or antenna parallel, or whatever feature establishes the body spacing and aspect angle and how that represents intended and expected use. The SAR evaluations for this radio were performed on October 14-15, 2009. The test reduction provisions and requirements specified in KDB 447498 Section 6 were not mandated until the release of D01v04 on November 13, 2009. Prior to this KDB release date the FCC requirements as stated above for applying appropriate procedures were not evidently clear as they are being stated now after the fact. At the time when the SAR evaluations were performed there were no apparent guidance documents specifically addressed for PTT Radios in the Occupational Page 2 of 2 category and therefore procedures in OET B 65 Supplement C 01-01 and IEEE 1528-2003 were implemented. It is understood that the specific requirements stated in item 2) above are now in force and have been since the release of KDB 447498 D01v04; however prior to that it was not evidently clear at the time of the SAR evaluation of this device that these specific procedures should have been applied for a higher-output device and that the existing procedures in OET B 65 Supplement C 01-01 and IEEE 1528-2003 were not necessarily appropriate for this evaluation. 3) TCB please explain how KDB 447498 items 6) a) and 6) b) were addressed during this application review; otherwise test reduction considerations may remain to be addressed under this instant 2.962(f)(6) / 2.962(f)(5)(i) / 2.947(e) process. The test reduction procedures of KDB 447498 Section 6) a) and b) were not released until November 13, 2009 and the SAR evaluations were performed in October 2009. At the time of the SAR evaluations it was not evidently clear that the 3 dB mid channel only provision should not apply to high power radios. 4) If not in SAR report already, TCB please coordinate with test lab / applicant to address the following concerning appropriate spacing positioning and reporting for belt-clip and different batteries: - applicant / test lab must clearly identify and justify whatever reference points along device are used - for example if body-worn setup photos may indicate that some unspecified point along the antenna is being held at some X.X cm spacing while the belt-clip rocks front or back versus battery thickness - typically a flat belt-clip and specific battery will determine unambiguous device tilt - however in case of curved-surface belt-clip, device tilt and spacing at various reference points along length of device and antenna must be identified - other disambiguated positioning schemes might be antenna parallel to phantom, or battery surface parallel to phantom - where appropriate please revise test setup and/or setup photos accordingly The body-worn SAR evaluations were performed with the flat center section of the belt-clip parallel to the planar phantom (note: only the center section of the belt-clip is flat; the…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: ALH415100 – Kenwood (TCB-p0970014) Date: February 18, 2010 To: Steve Schafer - [email protected] From: Tim Harrington - [email protected] Correspondence Ref Number: 81357 Form 731 Confirmation Number: TC765740 Response noted: Blue lettering is from John Erhard, Engineering Manager for Compliance Testing Red lettering is from Jon Hughes, Project Manager for Celltech 1) Per 2.962(f)(1), applications processed by TCB must be in accordance with FCC rules, policies, and procedures. For this filing, the line-entry part 90-frequency listings encompass frequencies not authorized for part 90 - therefore filing does not appear to be in accordance with KDB pub. 634817. Please explain and/or revise all applicable parts of filing where appropriate. The frequency band of this device does encompass small sections of bands that are available for use by and subject to other rule sections, however this application is for Part 90 only and the final sale and licensing of these radios will be under that rule section as stated on the grant and application. 2) Basic SAR evaluation considerations for PTT portable devices: a) SAR evaluations must address all device configuration options including all antennas, body-worn accessories, audio accessories, batteries, for each transmission band of all antenna options. See also KDB 447498 item 6). b) Note that the majority of procedures in OET B 65 Supplement C 01-01, especially Appendix D, are intended for cellphone SAR evaluations; similar considerations for test reduction based on SAR levels are available in KDB 447498 item 1) for certain other device configurations. These types of test reductions are applicable only for full and complete device test conditions, without application of other types of test reductions such as under KDB 447498 item 6) or certain similar reductions described in other KDB publications for specific devices. c) Provisions for "a priori" omitting some transmission-band channels for each antenna based on initial tests for the mid-band (and/or highest output) channel, have not been established for higher-output devices using mid-band and reduced testing of multiple accessory combinations and configurations; KDB 447498 item 1) e) i), for example, is not directly applicable for devices operating under higher occupational exposure limits. Reduction of number of test channels on top of reduction for certain accessory configurations requires beforehand FCC test plan approval; requests for such consideration must clearly explain device and configuration details and proposed subset of tests relative to full test requirements matrix. d) For belt-clips and/or body-worn accessories having a body-facing surface that is not parallel with main enclosure of the device, and/or having features or protrusions causing relative tilt of device housing and/or antenna, filing must clearly document all spacings to phantom / body along length of device, and provide details and rational how and why SAR positions hold either enclosure parallel to phantom, or antenna parallel, or whatever feature establishes the body spacing and aspect angle and how that represents intended and expected use. The SAR evaluations for this radio were performed on October 14-15, 2009. The test reduction provisions and requirements specified in KDB 447498 Section 6 were not mandated until the release of D01v04 on November 13, 2009. Prior to this KDB release date the FCC requirements as stated above for applying appropriate procedures were not evidently clear as they are being stated now after the fact. At the time when the SAR evaluations were performed there were no apparent guidance documents specifically addressed for PTT Radios in the Occupational Page 2 of 2 category and therefore procedures in OET B 65 Supplement C 01-01 and IEEE 1528-2003 were implemented. It is understood that the specific requirements stated in item 2) above are now in force and have been since the release of KDB 447498 D01v04; however prior to that it was not evidently clear at the time of the SAR evaluation of this device that these specific procedures should have been applied for a higher-output device and that the existing procedures in OET B 65 Supplement C 01-01 and IEEE 1528-2003 were not necessarily appropriate for this evaluation. 3) TCB please explain how KDB 447498 items 6) a) and 6) b) were addressed during this application review; otherwise test reduction considerations may remain to be addressed under this instant 2.962(f)(6) / 2.962(f)(5)(i) / 2.947(e) process. The test reduction procedures of KDB 447498 Section 6) a) and b) were not released until November 13, 2009 and the SAR evaluations were performed in October 2009. At the time of the SAR evaluations it was not evidently clear that the 3 dB mid channel only provision should not apply to high power radios. 4) If not in SAR report already, TCB please coordinate with test lab / applicant to address the following concerning appropriate spacing positioning and reporting for belt-clip and different batteries: - applicant / test lab must clearly identify and justify whatever reference points along device are used - for example if body-worn setup photos may indicate that some unspecified point along the antenna is being held at some X.X cm spacing while the belt-clip rocks front or back versus battery thickness - typically a flat belt-clip and specific battery will determine unambiguous device tilt - however in case of curved-surface belt-clip, device tilt and spacing at various reference points along length of device and antenna must be identified - other disambiguated positioning schemes might be antenna parallel to phantom, or battery surface parallel to phantom - where appropriate please revise test setup and/or setup photos accordingly The body-worn SAR evaluations were performed with the flat center section of the belt-clip parallel to the planar phantom (note: only the center section of the belt-clip is flat; the…

Text truncated - open the document above for the full version.

TK-3360-K, TK-3360-X FCC ID: ALH415100 Front View Rear View TK-3360-K, TK-3360-X FCC ID: ALH415100 Left View Right View TK-3360-K, TK-3360-X FCC ID: ALH415100 Top View Bottom View

TK-3360-K, TK-3360-X FCC ID: ALH415100 TK-3360-K TK-3360-X

TK-3360-K, TK-3360-X FCC ID: ALH415100 Component Side View TK-3360-K, TK-3360-X FCC ID: ALH415100 Foil Side View TK-3360-K, TK-3360-X FCC ID: ALH415100 TK-3360-K, TK-3360-X FCC ID: ALH415100 Component Side View Foil Side View

Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 Date: October 13, 2009 Applicant: Kenwood USA Corporation Communications Division 3970 Johns Creek Court, Suite 100 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Equipment: TK-3360-K, -X FCC ID: ALH415100 FCC Rules: Part 90 Gentlemen: Enclosed please find your copy of the Engineering Test Report for which you are subject to the restrictions as listed on the attached summary. Once a Telecommunication Certification Body (TCB) issues a Grant the Federal Communication Commission (FCC) has 30 days to review the application and request added information. It is your decision whether or not to market the equipment subject to a possible recall before the end of the 30 days. If your equipment is still retained by us, it will be returned to you 30 days after approval is achieved. Our invoice for services has been directed to your Accounts Payable Department. For any additional information please contact us. Thank you. Sincerely yours, John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 Summary of Restrictions 1. All submissions to the FCC are subject to their Examiner's interpretation. 2. Please allow from 60 to 90 days before hearing from the FCC with regard to any submission. 3. The FCC can set aside any action; modify or set aside any action, within 30 days. (FCC Rule 1.108, 1.113). 4. Under Rule 2.803, if device is not type accepted/certificated then it must not be sold, leased, offered for sale, imported, shipped or distributed or advertised for sale. 5. FCC can revoke its certificates at any time if the equipment does not meet or continue to meet their Rules. (Rule Parts 2.927, 2.939). 6. FCC can request a sample at any time (2.936). Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 Date: October 13, 2009 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood USA Corporation Equipment: TK-3360-K, -X FCC ID: ALH415100 FCC Rules: Part 90 Dear Gentleman: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Best regards, John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 Test Report for Model: TK-3360-K, -X to Federal Communications Commission Rule Part 90 Date of report: October 13, 2009 On the Behalf of the Applicant: Kenwood USA Corporation At the Request of: Kenwood USA Corporation Communications Division 3970 Johns Creek Court, Suite 100 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 Reviewed by: John Erhard, Engineering Manager Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 Test Report Revision History Revision Date Revised By Reason for revision 1.0 October 13, 2009 G. Corbin Original Document 2.0 November 04, 2009 G. Corbin Updated sections for Modulation Limiting and Frequency Stability Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 List of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: Kenwood USA Corporation FCC ID: ALH415100 By Applicant: 1. Letter of Authorization 2. Confidentiality Request: 0.457 And 0.459 3. Identification Drawings, 2.1033(c)(11) Label Location of Label Compliance Statement Location of Compliance Statement 4. Photographs, 2.1033(c)(12) 5. Documentation: 2.1033(c) (3) User Manual (9) Tune Up Info (10) Schematic Diagram (10) Circuit Description Block Diagram Parts List Active Devices 6. MPE/SAR Report By Compliance Testing: A. Testimonial & Statement of Certification Compliance Testing 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 (866) 311-3268 phone, (480) 926-3598 fax p0970014, d09a0006 Rev 2.0 The Applicant has been cautioned as to the following: 15.21 Information to the User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsibl…

Text truncated - open the document above for the full version.