AZ489FT3833Portable 2-Way Radio

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *6881095C98* 6881095C98-H *NNTN7223E* NNTN7223E MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2012 Motorola Solutions, Inc. All rights reserved. ATTENTION! 6881095C98-H_SafetyP_Eng.fm Page 1 Tuesday, July 24, 2012 1:43 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C98-H_SafetyP_Eng.fm Page 2 Tuesday, July 24, 2012 1:43 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C98-H_SafetyP_Eng.fm Page 3 Tuesday, July 24, 2012 1:43 PM 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 6881095C98-H_SafetyP_Eng.fm Page 4 Tuesday, July 24, 2012 1:43 PM 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front of the face. Hold the radio in a vertical position with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the n…

Text truncated - open the document above for the full version.

M MOTOTRBO XPR TM 7150 Non-Display Portable User Guide 68009677001-A NAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PM draft NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PM draft Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: XPR 7150 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this dev ice complies with Part 15 of the FCC Ru les. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the fo llowing two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PM draft Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PM draft Contents English iii ContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR 7150 Digital Portable Radio.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . vi Product Safety and RF Exposure Compliance . . .vi Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . viComputer Software Copyrights . . . . . . . . . . . . . . . vii Handling Precautions . . . . . . . . . . . . . . . . . . . . . . viiiGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Universal Con nector Cover (Dust Cover) 4 Attaching the Accessory Connector . . . . . . . . . . . . . 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5 Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6 Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 8 Assignable Radio Functions . . . . . . . . . . . . . . . . . 8Assignable Settings or Utility Functions . . . . . . . . . 9 Push-To-Talk (PTT) Bu tton . . . . . . . . . . . . . . . . . . . . 9 Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 12 Identifying Status Indicators . . . . . . . . . . . . . . . . . . 15 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Receiving and Making Calls . . . . . . . . . . . . . . . . . . 18 Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 18Receiving and Responding to a Radio Call . . . . . . 19 Receiving and Responding to a Group Call . . . . . 19Receiving and Responding to a Private Call . . . 20 Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 21Receiving and Responding to a Phone Call . . . . 22 Phone Call as a Private Call or Group Call . . . 22Phone Call as an All Call . . . . . . . . . . . . . . . . . 22 NAG-LACR.book Page iii Tuesday, March 12, 2013 3:37 PM draft Contents English iv Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 23 Making a Call with the Channel Selector Knob . . 23 Making a Group Call . . . . . . . . . . . . . . . . . . . . 23Making a Private Call . . . . . . . . . . . . . . . . . . . 24 Making a Selective Call . . . . . . . . . . . . . . . . . . . 25 Making an All Call . . . . . . . . . . . . . . . . . . . . . . 25 Making a Phone Call with the Programmable Phone Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 26Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

FCC ID: AZ489FT3833 EXHIBIT 13A ________________________________________________________________________________________ Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida May 14 th , 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT3833, MOTOTRBO VHF (136 – 174 MHz), 5 Watts Rated Power, 6 Watts Max Power Gentlemen: Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Portable Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency ranges: 136 – 174 MHz : 1-5 Watts (Nominal) To aid equipment authorization in foreign countries which accept United States FCC Grant for equipment authorization, Motorola Solutions is requesting that the FCC lists 136 – 174 MHz on the FCC Grant for equipment authorization. We are requesting Certification under Part 80, 90.210 and 90.210(e) of the Commission’s Rules to allow operation of this equipment in 136 – 174 MHz. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. This transmitter also complies with § 80.203(b) in that this transmitter is not capable of being programmed by station operators using the external controls to transmit on channels other than those programmed by the manufacturer, service or maintenance personnel. In addition, this transmitter is intended for work-related occupational use only under Part 80 and Part 90 of the FCC rules. Additionally, the radio is equipped with a Bluetooth transmitter capable of clear communication with fixed power operating within the following frequency ranges: 2.402-2.480 GHz: 5-10 mW The Bluetooth transmitter complies with the requirements of FCC Part 15 subpart C. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793. Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ489FT3833 EXHIBIT 13B ________________________________________________________________________________________ Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida CONFIDENTIALITY REQUEST May 14 th , 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality for Transmitter with FCC ID:AZ489FT3833 Dear Sir / Madam, Motorola Solutions Inc is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola Solutions considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Please contact me if you require any additional information. Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ489FT3833 EXHIBITS 13C _________________________________________________________________________________ Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida May 14 th , 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Dear Sir/Madam: The Mototrbo VHF Portable 2-Way radio was designed to operate in the frequency bands 136- 174 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola is requesting that the FCC lists the frequencies 136-174MHz under FCC Rule Parts 90 on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Part 80 Federal Emission Designator Rule 136-150.8 x 11K0F3E/ 16K0F3E**/ 7K60F1E/ 7K60F1D/ 7K60F1W/ 7K60FXE/ 7K60FXD 150.8-161.6250 x x 161.6250-161.7750* 161.7750-173.4 x x 173.4-174 x * Canada ** Canada and Rule Part 80 Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3A SHEET 2 OF 7 Exhibit 3A BACK VIEW WITH BATTERY Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3B SHEET 3 OF 7 Exhibit 3B FRONT VIEW Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3C SHEET 4 OF 7 Exhibit 3C BACK VIEW (FCC LABELS) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3D SHEET 5 OF 7 Exhibit 3D SIDE VIEW (RIGHT) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3E SHEET 6 OF 7 Exhibit 3E SIDE VIEW (LEFT) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 3F SHEET 7 OF 7 Exhibit 3F TOP VIEW

Applicant: Motorola Solutions Inc FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or Sketch Top of Radio X Back of Radio Back of Radio under Belt Clip TYPE X The label is a polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with the minimum peel strength of 32 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. Figure 1: FCC IC Label for Non Key Pad model (AAH69JDC9KA2AN)

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 1 OF 7 Internal Photographs The following photographs are attached. Exhibit 1. RF board without & with Shields (Top) 9A 2. RF board without & with Shields (Bottom) 9B 3. Chassis and housing (front side) 9C 4. Chassis and housing (back side) 9D 5. GOB board 9E Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 2 OF 7 Exhibits 9A RF board with and without Shields (Top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 3 OF 7 Exhibit 9B RF board with and without Shields (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 4 OF 7 Exhibit 9C PCB board with chassis and housing (Top) RF Port (For conducted measurement) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 5 OF 7 Exhibit 9D PCB board with chassis and housing (Bottom) Bluetooth Antenna Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 6 OF 7 Exhibit 9E GOB board (Top) GOB board with shield (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 EXHIBIT 9 SHEET 7 OF 7 GOB board without shield (Bottom)

FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: Certification Date Certification No.: FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Part 1 of 2 APPENDICES FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Part 2 of 2 Report Revision History DateRevision Comments FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 1.0 Introduction example 2.0 Abbreviations / Definitions 3.0 Referenced Standards and Guidelines FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 4.0 SAR Limits TABLE 1 EXPOSURE LIMITS SAR (W/kg) (General Population / Uncontrolled Exposure Environment) (Occupational / Controlled Exposure Environment) Spatial Average - ANSI - (averaged over the whole body) 0.08 0.4 Spatial Peak - ANSI - (averaged over any 1-g of tissue) 1.6 8.0 Spatial Peak – ICNIRP/ANSI - (hands/wrists/feet/ankles averaged over 10-g) 4.0 20.0 Spatial Peak - ICNIRP - (Head and Trunk 10-g) 2.0 10.0 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 5.0 SAR Result Scaling Methodology: DC P P measSARCalcMax Drift 6.0 Description of Device Under Test (DUT): FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 7.0 Optional Accessories and Test Criteria: 7.1 Antennas: TABLE 2 Antenna Models Description Selected for Test Tested *Note: Antenna PMAD4119A bandwidth is outside FCC Part 90. 7.2 Battery: TABLE 3 Battery Models Description Selected for Test TestedComments 7.3 Body worn Accessories: TABLE 4 Body worn Models Description Selected for Test TestedComments FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 7.4 Audio Accessories: TABLE 5 Audio Acc. Models Description Selected for Test TestedComments FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 TABLE 5 Audio Acc. Models Description Selected for Test TestedComments 8.0 Description of Test System: 8.1 Descriptions of Robotics/Probes/Readout Electronics: TABLE 6 Disometric System Type System Version DAE Type Probe Type FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 8.2Description of Phantom(s) TABLE 7 Phantom Type Phantom ID(s) Material Parameters Phantom Dimensions LxWxD (mm) Material Thickness (mm) Support Structure Material Loss Tangent (wood) 8.3Description of Simulated Tissue: Simulated Tissue Composition (by mass) TABLE 8 Reference Standards % of Listed Ingredients 300 MHz 2450 MHz Head Body Head Body FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 9.0 Additional Test Equipment: TABLE 9 Equipment Type Model Number Serial Number Calibration Date Calibration Due Date Temperature Recording Equipment Tissue Station Dipole DAE Probe * Calibration is not required by the OEM. The dielectric probe kit is used in conjunction with a calibrated network analyzer. The dielectric probe kit is calibrated for short, open, and load using the calibrated network analyzer. A saline solution is routinely measured as an additional check point. FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 10.0 SAR Measurement System Verification: 10.1 Equivalent Tissue Test Results: TABLE 10 Frequenc y (MHz) Tissue Type Conductivity Target & Range (S/m) Dielectric Constant Target & Range Conductivity Meas. (S/m) Dielectric Constant Meas.Tested Date FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 10.2System Check Test Results: TABLE 11 Probe Serial # Tissue Type Dipole Kit / Serial # Reference SAR @ 1W (W/kg) System Check Results Measured (W/kg) System Check Test Results when normalized to 1W (W/kg) Tested Date 11.0Environmental Test Conditions: TABLE 12 Ambient Temperature TargetMeasured Relative Humidity Tissue Temperature FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 12.0DUT Test Methodology 12.1Measurements 12.2DUT Configuration(s) 12.3DUT Positioning Procedures 12.3.1 Body 12.3.2 Head 12.3.3 Face 12.4DUT Test Channels: clowhighc fffroundupN FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 12.5DUT Test Plan: 13.0DUT Test Data 13.1Assessment at the Body for 150.8-173.4 MHz Band: TABLE 13 Test Freq (MHz) Power (W) 13.1.1 Assessment at the Body with Body worn PMLN6545A: TABLE 14 Assessments at the Body (CW mode) AntennaBattery Carry Accessory Cable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g-SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g- SAR (W/kg) Max Calc. 10g- SAR (W/kg)Run# 1.20 0.75 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 13.1.2 Assessment of wireless BT configuration at the Body: TABLE 15 Assessments at the Body (CW mode) AntennaBattery Carry Accessory Cable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g-SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g- SAR (W/kg) Max Calc. 10g- SAR (W/kg)Run# 0.87 0.57 13.1.3 Assessment of other audio accessories at the body: 13.2Assessment outside FCC Part 90 at the Body: TABLE 16 Assessments at the Body (CW mode) AntennaBattery Carry Accessory Cable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g-SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g- SAR (W/kg) Max Calc. 10g- SAR (W/kg)Run# 0.37 0.26 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 13.3Assessment at the Face: TABLE 17 Test Freq (MHz) Power (W) TABLE 18 Assessments at the Face (CW mode) AntennaBattery Carry AccessoryCable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g- SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g- SAR (W/kg) Max Calc. 10g- SAR (W/kg)Run# 0.550.42 13.4Assessment outside FCC Part 90 at the Face: TABLE 19 Assessments at the Body (CW mode) AntennaBattery Carry Accessory Cable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g-SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g- SAR (W/kg) Max Calc. 10g- SAR (W/kg)Run# 0.44 0.34 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 13.5Assessment for Industry Canada frequency range: 13.6Assessment for Bluetooth TABLE 20 BT Assessments at the Body (CW mode) AntennaBatteryCarry Accessory Cable Accessory Test Freq. (MHz) Initial Power (W) SAR Drift (dB) Meas. 1g-SAR (W/kg) Meas. 10g- SAR (W/kg) Max Calc. 1g-SAR (W/kg) Ma…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: Certification Date Certification No.: FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 APPENDIX A Measurement Uncertainty Table 1: Uncertainty Budget for Device Under Test, for 100 MHz to 300 MHz abcde = f(d,k) fg h = c x f / e i = c x g / e k Uncertainty Component IEEE 1528 section Tol. (± %) Prob Dist Div. c i (1 g) c i (10 g) 1 g u i (±%) 10 g u i (±%) v i Measurement System Test sample Related Phantom and Tissue Parameters Combined Standard Uncertainty Expanded Uncertainty k FCD-0558 Uncertainty Budget Rev.8.1 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Table 2: Uncertainty Budget for System Verification (dipole & flat phantom) for 300 MHz to 550 MHz abcde = f(d,k) fg h = c x f / e i = c x g / e k Uncertainty Component IEEE 1528 section Tol. (± %) Prob. Dist. Div. c i (1 g) c i (10 g) 1 g u i (±%) 10 g u i (±%) v i Measurement System Dipole Phantom and Tissue Parameters Combined Standard Uncertainty Expanded Uncertainty k FCD-0558 Uncertainty Budget Rev.8.1 ak ci ui vi FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Table 3: Uncertainty Budget for Device Under Test, for 800 MHz to 3 GHz abcde = f(d,k) fg h = c x f / e i = c x g / e k Uncertainty Component IEEE 1528 section Tol. (± %) Prob Dist Div. c i (1 g) c i (10 g) 1 g u i (±%) 10 g u i (±%) v i Measurement System Test sample Related Phantom and Tissue Parameters Combined Standard Uncertainty Expanded Uncertainty k FCD-0558 Uncertainty Budget Rev.8.1 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Table 4: Uncertainty Budget for System Verification (dipole & flat phantom) for 800 MHz to 3 GHz abcde = f(d,k) fg h = c x f / e i = c x g / e k Uncertainty Component IEEE 1528 section Tol. (± %) Prob. Dist. Div. c i (1 g) c i (10 g) 1 g u i (±%) 10 g u i (±%) v i Measurement System Dipole Phantom and Tissue Parameters Combined Standard Uncertainty Expanded Uncertainty k FCD-0558 Uncertainty Budget Rev.8.1 ak ci ui vi FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 APPENDIX B Probe Calibration Certificates FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124

FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: Certification Date Certification No.: FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 APPENDIX C Dipole Calibration Certificates FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 SR11124 FCC ID: AZ489FT3833 / IC: 109U-89FT3833 S…

Text truncated - open the document above for the full version.