AZ489FT4855Astro XTS 5000

ASTRO ® XTS ™ 5000 Digital Portable Radio, Model III Quick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupati onal use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 68P81095C98) to ensure compliance with RF energy exposure limits. Write your radio’s programmed features on the dotted lines. Radio On/OffZones/ChannelsReceive/TransmitSend Emergency Alarm Send Emergency CallSend Silent Emergency Alarm Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ! C a u t i o n 16-Position Select Knob _ _ _ _ _ _ _ Speaker/Mic Top Button _ _ _ _ _ _ _ Concentric Switch_ _ _ _ _ _ Display Keypad Menu Select ButtonsApp Button (for future use) Top Side Button_ _ _ _ _ _ _On/Off/Volume Knob Side Button 1_ _ _ _ _ _ _Side Button 2_ _ _ _ _ _ _ PTT Button 3-Position Switch _ _ _ _ _ _ _ 4-Way Navigation ButtonHome Button 1On - On/Off/Volume knob clockwise. 2Off - On/Off/Volume knob counterclockwise. 1 Zone - Zone switch to desired zone. 2 Channel - Channel switch to desired channel. 1 Radio on and select zone/channel. 2 Listen for a transmission. - or -Press and hold Volume Set button. - or -Press Monitor button and listen for activity. 3 Adjust volume, if necessary. 4Press PTT to transmit; release to receive. Radio on and press Emergency button. Display shows current zone/channel, andEMERGENCY . Red LED lights; you hear short, medium-pitched tone. Note: To exit emergency at any time, press and hold Emergency button. When acknowledgment is received, you hear four beeps; alarm ends; radio exits emer-gency. 1 Radio on and press Emergency button. Note: To exit emergency at any time, press and hold Emergency button. 2 Press and hold PTT . Announce your emergency into the microphone. 3 Release PTT to end call. 4 Press and hold Emergency button to exit emergency. 1 Radio on and press Emergency button. Display does not change; you see no LED; you hear no tone. Note: To exit emergency at any time, press and hold Emergency button. 2 Silent emergency continues until you: • Press and hold Emergency button to exit emergency state. - or - • Press and release PTT to exit silent emergency and enter regular emergency (alarm, call, or alarm with call). Display Status Symbols Menu Entries (Use With Menu Navigation) m Receiving an individual call p The radio is in the view or program mode; On Steady = view mode; Flashing = program mode s Received signal strength for the current site (trunking only). The more stripes in the symbol, the stronger the signal. b Flashes when the battery is low. r You are talking directly to another radio or through a repeater; On = direct; Off = repeater C This channel is being monitored. c Your radio is in secure operation; On = secure operation; Off = clear operation; Flashing = receiving an encrypted voice call T The radio is scanning a scan list S Priority 1 Channel during scan S Priority 2 Channel during scan Entry Menu Selection Page BATT Smart Battery 16 CALL Private Call /Selective Call 59/63 CHAN Select a Channel 22 CLCK Set the Time and Date 95 DIR Repeater/Direct 74 ERAS Key Zeroization 82 KEY Key Selection 79 KSET Keyset Selection 80 LOGF Radio Lock 31 MUTE Keypad Mute 32 NAME Text Select 42 NUM Number Select 41 Entry Menu Selection Page PAGE Call Alert Page 67 PHON Phone 55 PROG Editing 41 PSWD Password 30 PWR TX Power Level 27 REKY Rekey Request 85 RPGM Reprogram Request 88 SCAN Scan On/Off 51 SITE Site Lock/Unlock 92 STS Status Call 72 TGRP Talkgroup Call 70 VIEW View a List 40 ZONE Select a Zone 21 Menu Navigation U to find Menu Entry D , or E , or F directly below Menu Entry to select h to exit V or U to scroll through sub-list D , or E , or F directly below Menu Entry to select ASTRO ® XTS ™ 5000 Digital Portable Radio Model III User Guide 68P81094C27-C Motorola, Inc. 8000 West Sunrise Blvd. Ft. Lauderdale, FL 33322 Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 68P81095C98) to ensure compliance with RF energy exposure limits. Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examine…

Text truncated - open the document above for the full version.

English Product Safety and RF Exposure The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. For radios that have been approved as intrinsically safe, read the instructions and information on intrinsic safety on page 9 of this booklet. Compliance with RF Energy Exposure Standards NOTICE: This radio is intended for use in occupational/controlled applications where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ! C a u t i o n

68P81087C79-F © Motorola, Inc. 2002. Commercial, Government and Industrial Solutions Sector 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 Printed in U.S.A. 06/02. All Rights Reserved. 2 English Federal Communications Commission (FCC) Regulat ions The FCC has established limits for safe exposure to radio frequency (RF) emissions from portable two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before portable two-way radios can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of, and exercise control over, their exposure. Awareness of RF exposure can be accomplished by the use of labels, information and instructions in manuals or safety booklets, or by appropriate means. Your Motorola two-way radio has an RF exposure information label in the battery compartment. This user safety booklet includes useful information about RF exposure and helpful instructions on how to control your RF exposure. Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at usage factors of up to 50% talk–50% listen. In terms of measuring RF energy for compliance with FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved, supplied batteries for this radio are rated for a 5-5-90 duty cycle (5% talk–5% listen–90% standby), even though this radio complies with FCC occupational exposure limits at duty cycles of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 3 English • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation – Human Exposure) Standard, 2001 • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular and PCS product certification.” Compliance and Control Guidelines and Operating Instructions for Portable Two-Way Radios To control your exposure and ensure compliance with the occupational/ controlled environment exposure limits, always adhere to the following procedures: •Transmit no more than 50% of the time. To transmit (talk), push the Push- To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time or less is important since the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). •Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one to two inches (2.5 to 5 centimeters) away from the lips. Keeping the radio at a proper distance is important since RF exposures decrease with distance from the antenna. 4 English •For body-worn operation, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. Using non– Motorola-approved accessories may result in exposure levels which exceed the FCC’s occupational/controlled environment RF exposure limits. •If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, ensure the antenna and the radio are kept one inch (2.5 centimeters) from the body when transmitting. Keeping the radio at a proper distance is important since RF exposures decrease with distance from the antenna. •Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of non–Motorola-approved antennas, batteries and accessories may exceed FCC RF exposure guidelines. For a list of Motorola- approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://www.motorola.com/cgiss/portables/xts5000.shtml For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth . 5 English Electromagnetic Interference/Compatibility NOTE:Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. Facilities To avoid electromagnetic interference and/or compatibility conf…

Text truncated - open the document above for the full version.

English Product Safety and RF Exposure The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. For radios that have been approved as intrinsically safe, read the instructions and information on intrinsic safety on page 9 of this booklet. Compliance with RF Energy Exposure Standards NOTICE: This radio is intended for use in occupational/controlled applications where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ! C a u t i o n *6881087C79* 68P81087C79-F © Motorola, Inc. 2002. Commercial, Government and Industrial Solutions Sector 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 Printed in U.S.A. 06/02. All Rights Reserved. 2 English Federal Communication Commission (FCC) Regulations The FCC has established limits for safe exposure to radio frequency (RF) emissions from portable two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before portable two-way radios can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of, and exercise control over, their exposure. Awareness of RF exposure can be accomplished by the use of labels, information and instructions in manuals or safety booklets, or by appropriate means. Your Motorola two-way radio has an RF exposure information label in the battery compartment. This user safety booklet includes useful information about RF exposure and helpful instructions on how to control your RF exposure. Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at usage factors of up to 50% talk–50% listen. In terms of measuring RF energy for compliance with FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved, supplied batteries for this radio are rated for a 5-5-90 duty cycle (5% talk–5% listen–90% standby), even though this radio complies with FCC occupational exposure limits at duty cycles of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 3 English • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation – Human Exposure) Standard, 2001 • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular and PCS product certification.” Compliance and Control Guidelines and Operating Instructions for Portable Two-Way Radios To control your exposure and ensure compliance with the occupational/ controlled environment exposure limits, always adhere to the following procedures: •Transmit no more than 50% of the time. To transmit (talk), push the Push- To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time or less is important since the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). •Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one to two inches (2.5 to 5 centimeters) away from the lips. Keeping the radio at a proper distance is important since RF exposures decrease with distance from the antenna. 4 English •For body-worn operation, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness, if available, for this product. All Motorola-approved accessory, antenna and device combinations comply with FCC occupational/controlled environment RF exposure limits. Exposure information on various accessory, antenna and device combinations can be found under the Display Exhibit section of http:// www.fcc.gov/oet/fccid after searching on the FCC ID number, which can be obtained from the label of your radio. Use of non–Motorola-approved accessories may result in exposure levels which exceed the FCC’s occupational/controlled environment RF exposure limits. •If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, ensure the antenna and the radio are kept one inch (2.5 centimeters) from the body when transmitting. Keeping the radio at a proper distance is important since RF exposures decrease with distance from the antenna. •Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of non–Motorola-approved antennas, batteries and accessories may exceed FCC RF exposure guidelines. For a list of Motorola- approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://www.motorola.com/cgiss/portables/xts5000.shtml For additional information on expos…

Text truncated - open the document above for the full version.

Applicant: MOTOROLA INC FCC ID: AZ489FT4855 EXHIBIT 2 STATEMENT OF CERTIFICATION The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) MSEE Oklahoma State University MBA Oklahoma State University 2) 8 years experience in the development, testing and certification of Land Mobile Communications Products NAME: Stephen L. Kersten SIGNATURE: DATE: 16 September 2002 POSITION: Senior Staff Electrical Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME: Daniel Marks SIGNATURE: DATE: 16 September 2002 POSITION: Engineering Manager

Applicant: Motorola Inc. FCC ID: AZ489FT4855 Confidentiality Requested Description I. Transmitter Technical Characteristics -- Pursuant 2.1033 (c) A. RF Power Output 1 – 5.8 Watt (Variable Power) B. Frequency Range 380 - 470 MHz C. Frequency Stability 0.00020 % D. Emissions 11K0F3E, 16K0F3E, 8K10F1D, 8K10F1E, 20K0F1E E. Spurious Emissions - 75 dBc F. DC Voltage and Current into 7.5 Volts the final RF amplifier stage/stages 2.0 Amps II. Transmitter Application: This transmitter is primarily intended for use as a hand-held portable radio. The transmitter is characterized by the following features, options and accessories. A. Power Supply Available Ni-Cad Battery X , Mercury Battery , Alkaline Battery X , AC , Lead Acid Battery , Ni-MH Battery X ,Li-Ion X B. Antenna Available 1. Helical X , Telescopic , Whip X , Dipole , Dribble External , External . C. Squelch Types Available 1. Carrier Squelch X . 2. Tone "Private Line" X . 3. Digital "Private Line" X . D. Microphone - Control 1. Remote Speaker Microphone X 2. Wireline control . E. Maximum Transmit Channel Capability 512 . F. Housing The transmitter will be housed in the housing shown in the accompanying photographs. G. Other Options 1. Single Tone Encoder 2. Multiple Single Tone Encoder 3. Touch Code Encoder 4. Unit ID Encoder X 5. EMS Telemetry Encoder 6. Time out Timer X 7. Voice Encryption X 8. Digital Signaling X 9. Sel-Call Decode X 10. Trunking X 11. Conventional X 12. Digital Voice X _ EXHIBIT 12

______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. Confidentiality Request Date: 21 st November 2002 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4855. Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath FCC Liaison Tel: (954) 723-5793 E-mail: [email protected] EXHIBIT 13b

FCC ID: AZ489FT4855 Date: 28th February 2003 Diane Poole Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: Form 731 Confirmation Number: EA978518 with FCC ID: AZ489FT4855. Dear Miss Poole; Motorola Inc., 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322, herein submits it’s request to include FCC Rule Part 80 (Maritime Services) on the FCC Grant. All data submitted for the Part 90 application is also applicable for the Part 80. Contact me at (954) 723-5793 if you require any additional information. Sincerely, /s/ Mike Ramnath FCC Liaison Email: [email protected]

FCC ID: AZ489FT4855 Date: 26th March 2003 Richard Fabina Chief, Equipment Authorization Branch Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: Form 731 Confirmation Number: EA978518 with FCC ID: AZ489FT4855. Dear Mr. Fabina; Motorola Inc., 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322, herein submits its request to amend the highest reported Body-Worn SAR value from 7.41 W/kg as listed on the FCC Grant to 6.95 W/kg. Motorola will not be offering for sale the Public Safety Microphone kit as compatible with antenna NAE6546 which has a SAR value of 7.41 W/kg as reported on page 7 in the 18 th February 2003 response to the FCC’s correspondence number 24784. We have amended the Users Manual to reflect that only antennas NAE6547 and NAE6549 are approved with Public Safety Microphone kits, NMN6247, NMN6250 and NMN6251. Please update the FCC files and re-issue the grant with the reduced highest SAR value 6.95 W/kg for Body-Worn. Contact me at (954) 723-5793 if you require any additional information. Sincerely, /s/ Mike Ramnath FCC Liaison Email: [email protected]

Applicant: Motorola Inc. FCC ID: AZ489FT4855 EXTERNAL PHOTOGRAPHS The following photographs are attached. Exhibit 1. Front view. 3A 2. Back view with battery. 3B 3. Back view (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F EXHIBIT 3 Applicant: Motorola Inc. FCC ID: AZ489FT4855 FRONT VIEW EXHIBIT 3A Applicant: Motorola Inc. FCC ID: AZ489FT4855 BACK VIEW WITH BATTERY EXHIBIT 3B Applicant: Motorola Inc. FCC ID: AZ489FT4855 BACK VIEW (FCC LABELS) EXHIBIT 3C Applicant: Motorola Inc. FCC ID: AZ489FT4855 SIDE VIEW (RIGHT) EXHIBIT 3D Applicant: Motorola Inc. FCC ID: AZ489FT4855 SIDE VIEW (LEFT) EXHIBIT 3E Applicant: Motorola Inc. FCC ID: AZ489FT4855 TOP VIEW EXHIBIT 3F

Applicant: Motorola Inc. FCC ID: AZ489FT4855 IDENTIFICATION LABEL LOCATION See the Attached Photograph or Sketch X Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. EXHIBIT 1 Applicant: Motorola Inc. FCC ID: AZ489FT4855 GENERAL INFORMATION I. Production Plans -- Pursuant 2.1033 (c) Quantity production is planned. II. Application References -- Pursuant 2.1061 Reference is made to the following Motorola "Application References" 1. Portable Products and their application. 2. Portable Products Transmitter Modulations Methods. 3. Plantation, Florida Antenna Range. III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ rules. Necessary Bandwidth Computation for 8K10F1E Emission Designator The FCC Rule & Regulations Part 2, §2.202(b) defines Necessary Bandwidth as the minimum value of the occupied bandwidth sufficient to ensure that transmission of information at the rate and with the quality required for the system employed. §2.202(c) lists four methods of determining the necessary bandwidth, including the use of formulas in §2.202(g), and measurement in cases where the other methods of §2.202(c) do not apply. It is felt that while these formulas apply well to voice and many older digital modulation systems, the formulas do not apply to the high performance digital modulation employed in the system submitted for Certification because of difficulties determining representative values for the factors K and M. We have, therefore, used the measurement criteria of §2.202(c)(4). The value cited, 8K10, is the bandwidth that contains 99% of the total transmitted power. The 99% value was chosen because §2.202(b) defines Necessary Bandwidth as the minimum value of the occupied bandwidth . In turn, §2.202(b) defines Occupied Bandwidth as the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5% of the total mean power radiated by a given emission, i.e., contains 99% of the total transmitted power. IV. Applicable References: • Reference Certification FCC ID: AZ489FT3804 • EIA/TIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards • FCC Federal Regulations Part 47 Sec. 2.1033 – 2.1055 • FCC Federal Regulations Part 90 Sec. 90.210 EXHIBIT 1A

Applicant: Motorola Inc. FCC ID: AZ489FT4855 INTERNAL PHOTOGRAPHS The following photographs are attached. Exhibit 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D 5. Vocon board with Shields (Top). 9E 6. Vocon board without Shields (Top). 9F 7. Vocon board (Bottom). 9G EXHIBIT 9 Applicant: Motorola Inc. FCC ID: AZ489FT4855 RF board with Shields (Top) EXHIBIT 9A Applicant: Motorola Inc. FCC ID: AZ489FT4855 RF board without Shields (Top) EXHIBIT 9B Applicant: Motorola Inc. FCC ID: AZ489FT4855 RF board with Shields (Bottom) EXHIBIT 9C Applicant: Motorola Inc. FCC ID: AZ489FT4855 RF board without Shields (Bottom) EXHIBIT 9D Applicant: Motorola Inc. FCC ID: AZ489FT4855 Vocon board with Shields (Top) EXHIBIT 9E Applicant: Motorola Inc. FCC ID: AZ489FT4855 Vocon board without Shields (Top) EXHIBIT 9F Applicant: Motorola Inc. FCC ID: AZ489FT4855 Vocon board (Bottom)) EXHIBIT 9G

Certificate Number: 1449-02 CGISS EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 S.A.R. EME Compliance Test Report Part 1 of 2 Attention: FCC Date of Report: November 22, 2002 Report Revision: Rev. A Manufacturer: Motorola Product Description: Portable 380-470 MHz 1-5W; 3x6 keypad, 6 line display Digital 512 Channel FCC ID: AZ489FT4855 Device Model: H18QDH9PW7AN Form-SAR-Rpt-Rev. 1.00 Page 1 of 25 Test Period: 9/26/02,10/7/02-11/4/02 Test Engineer: Stephen Whalen Sr. Test engineer Author: Michael Sailsman EME Regulatory Affairs Note: Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 2.0 of this report. Signature on File 11/22/02 ____________________________________________________________ _________________________ Ken Enger Date Approved Senior Resource Manager, Laboratory Director, CGISS EME Lab Note: This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. TABLE OF CONTENTS 1.0 Introduction 2.0 Reference Standards and Guidelines 3.0 Description of Test Sample 3.1 Test Signal 3.2 Test Output Power 4.0 Description of Test Equipment 4.1 Description of S.A.R Measurement System 4.2 Description of Phantom 4.2.1 Flat Phantom 4.2.2 SAM phantom 4.3 Simulated Tissue Properties 4.3.1 Type of Simulated Tissue 4.3.2 Simulated Tissue Composition 4.4 Test condition 5.0 Description of Test Procedure 5.1 Device Test Positions 5.1.1 Abdomen 5.1.2 Head 5.1.3 Face 5.2 Test Position Photographs 5.3 Probe Scan Procedures 6.0 Measurement Uncertainty 7.0 S.A.R. Test Results 7.1 S.A.R. results 7.2 Peak S.A.R. location 7.3 Highest S.A.R. results calculation methodology 8.0 Conclusion Appendix A: Power Slump Data/Shortened scan Appendix B: Data Results Appendix C: Dipole System Performance Check Results Appendix D: Calibration Certificates Appendix E: Illustration of Body-worn Accessories Appendix F: Accessories and options test status and separation distances Form-SAR-Rpt-Rev. 1.00 Page 2 of 25 REVISION HISTORY Date Revision Comments 11/15/02 O Initial release Prototype results 11/22/02 A Changed the frequency range of the standard antenna from 380-470MHz to 380- 520MHz; Changed the length of the optiona…

Text truncated - open the document above for the full version.