AZ489FT4873PMUE2384A-PORTABLE 2-WAY RADIO

PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure require- ments. Before using this product, read the RF energy awareness information and operating instruc- tions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6804110J47) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://ap.cgiss.motorola.com/AAD/index.html. © 2004 by Motorola, Inc. Motorola Technology Sdn. Bhd. (Co. No. 455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D.,11900 Penang, Malaysia Printed in Malaysia. 11/04. All Rights Reserved. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. Attaching and Removing the Antenna To Remove Antenna To Attach Antenna 1.Turn the antenna in a counter-clockwise direction until it disengages from the radio. 1.Fasten the antenna to the radio by placing the threaded end of the antenna into the Antenna Connector. 2.Rotate the antenna clockwise until tight. Antenna Connector Threaded End of Antenna Attaching and Removing the Battery To Remove Battery To Attach Battery 1.Slide the battery clasp away from the radio. 2.Slide the battery downwards. 3.Pull the battery away from the radio. 1.Fit the battery slots with the grooves on the radio. 2.Slide the battery upwards until a click is heard. Battery Clasp Grooves Attaching and Removing the Belt Clip To Remove Belt Clip To Attach Belt Clip 1.Insert the end of a key between the release tab and the back surface of the radio. 2.Lift the release tab. 3.Slide the belt clip upwards. 1.Align mounting rails of the radio with the grooves of the belt clip. 2.Slide the belt clip downwards until it clicks into place. Release Tab Mounting Grooves Charging your Radio 1.Turn off your radio and the A/C power sup- ply to your charger (if they are turned on). 2.Place your radio in the charger pocket. 3.Turn on the charger’s A/C power supply. 4.Charge your radio until the charger’s LED shows a steady green light (around 2 hours later). 5.Turn off the charger’s A/C power supply, and remove the radio from the charger pocket. 6.Turn on your radio; you should see all 3 bars of the Battery Level Indicator illumi- nated. Charger Pocket *6804113J11* 6815549H01-O Text.fm Page 1 Tuesday, December 28, 2004 12:21 PM LED Indicators LED ColourStateIndication RedIlluminatedRadio is transmitting. BlinkingBattery voltage is low. GreenIlluminatedRadio is receiving with PL/DPL disabled. BlinkingRadio is in active scanning mode. OrangeIlluminatedRadio is receiving with PL/DPL enabled. BlinkingAn error has occured. On/Off and Volume Knob • If the radio is off, turn this knob clockwise to turn the radio on. • If the radio is on, turn this knob counter-clockwise to turn the radio off. • Turn this knob clockwise to increase the volume. • Turn this knob counter-clockwise to decrease the volume. Push-to-Talk (PTT) button • Press and speak to microphone to send message. • Release and listen to receive messages. Programmable Buttons • The following functions are assigned as short press (press and release) or long press (press and hold for 1 second). • The default functions assigned to your radio are described in the table below. • If your dealer has re-programmed your radio’s programmable buttons, please enter the new functions in the table below. ButtonFunction High/Low PowerSelects desired power level to High or Low. Volume SetAllows you to check the audio and alert tone volume level. MonitorAllows you to monitor the current channel for activity; disables squelch. Sticky MonitorThe radio monitors continually until you press this button again. ScanStarts or stops channel scan. Nuisance Channel Delete Removes unwanted channel(s) temporarily from scan list during scan. Repeater/TalkaroundToggles your radio between functioning in Repeater mode or Talkaround mode. PL/DPLEnables or disables your radio from requiring matching PL/DPL to receive messages. Button LockLocks or unlocks all buttons except PTT and On/Off/Volume Knob. Battery Save ModeToggles your radio between functioning with Battery Saver ON or Battery Saver OFF. Squelch Selects desired squelch level: Normal or Tight. UnassignedNo function is programmed to this button. Press TypeProgrammable Button 1Programmable Button 2 Short PressMonitorScan Long PressSticky MonitorNuisance Channel Delete Press TypeProgrammable Button 1Programmable Button 2 Short Press Long Press Speaker • You will hear received messages through the speaker. Microphone • Speak into the microphone when send- ing message. Accessory Connector • Used to connect compatible accessories to your radio. Programming Port • Lower port of radio. • Use by your dealer to program your radio. Text.fm Page 2 Tuesday, December 28, 2004 12:21 PM

1-1 English Product Safety and RF Energy Exposure Booklet for Portable Two-Way Radios The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/ controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population or consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRISINIC SAFETY ON PAGE 9 OF THIS BOOKLET. © 1998, 2001, 2002, 2004 by Motorola, Inc. All rights reserved. Motorola Technology Sdn. Bhd. (Co. No. 455657-H), Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D., 11900 Penang, Malaysia Printed in Malaysia 06/04
 6804110J47-F 6804110j47_01_EN.fm Page 1 Tuesday, September 7, 2004 4:43 PM 1-2 English Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission (FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/ controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. 6804110j47_01_EN.fm Page 2 Tuesday, September 7, 2004 4:43 PM 1-3 English In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: ï United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J ï American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 ï Institute of Electrical and Electronic Engineers (IEEE) C95.1- 1999 Edition ï International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 ï Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 ï Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003 ï ANATEL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300 GHz" and "Attachment to resolution # 303 from July 2, 2002" "Additional Requirements for SMR, Cellular and PCS Product Certification" 6804110j47_01_EN.fm Page 3 Tuesday, September 7, 2004 4:43 PM 1-4 English RF Exposure Compliance and Control Guidelines and Operating In…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT4873 ______________________________________________________________________________ Motorola Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. CONFIDENTIALITY AND SHORT-TERM CONFIDENTIALITY REQUESTED Date: 29 th December 2004 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ489FT4873. Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. We are also requesting that the FCC mark Exhibit 3 (External Photos), 8a and 8b (Users Manual) and Exhibit 9, (Internal Photos) as Temporary or Short-Term Confidentiality as outlined in Public Notice DA 04-1705, dated June 15, 2004. This provision will give Motorola temporary confidentiality prior to product launch. Please mark Exhibits 4, 5, 10, and 12 as “Confidential” and Exhibit 3 (External Photos), 8a (Users Manual) and 9 (Internal Photos) as “Short- Term Confidential”. Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected] Exhibit 13b

Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 (Confidential Requested) EXTERNAL PHOTOGRAPHS Pursuant to 47 CFR 2.1033(c) 12 Figure 3-1: Front view of complete radio. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 2 OF 7 Figure 3-2: Back view of complete radio. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 3 OF 7 Figure 3-3: Right side (side connector) view of complete radio. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 4 OF 7 Figure 3-4: Left side (PTT) view of complete radio. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 5 OF 7 Fcc Label Location RF Safety Label Location Figure 3-5: Rear view of complete radio showing FCC Label & RF Safety Label location. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 6 OF 7 Figure 3-6: Top view of complete radio. Figure 3-7: Close-up view of RF Safety Label Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 3 SHEET 7 OF 7 Figure 3-8: Type of Antenna; Helical Antenna (PMAE2384A) Model List: Model Name Plate Tanapa Number Description - - PMUE2384A MagOne 450-470MHz 1 & 4W; 8 & 16 channels; Dell Navy

Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 1 SHEET 1 OF 1 EXHIBIT 1 IDENTIFICATION LABEL Pursuant to 47 CFR 2.925(a), 2.1033(c), 2.0165 EXHIBIT 1A - LABEL LOCATION A nameplate of the type presented below will be affixed to every transmitter. It will be placed on the bottom of the unit near the front. Shown below is a photo of the actual label affixed to the cast chassis of the transmitter. Figure 1-1: FCC Label EXHIBIT 1B - GENERAL INFORMATION 1. Application References: TIA/EIA-603B Land Mobile FM or PM Communications Equipment Measurement and Performance Standards Code of Federal Regulations Title 47, Part 2, Sec. 2.1033-2.1057, Sec. 2.1077(a) and Part 90, Section 90.210. 2. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commission’s rules. The intended use of this transceiver includes applications covered in the Code of Federal Regulations Title 47 and Part 90. Maximum transmitter power shall not be adjustable by the user. 3. Applicable Reference • Reference Certification FCC ID: AZ489FT4873 • EIA/TIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards. • FCC Federal Regulations Part 47 Sec. 2.1033-2.1057 • FCC Federal Regulations Part 90 Sec.90.210

Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 9 SHEET 1 OF 3 EXHIBIT 9 (Confidential Requested) INTERNAL PHOTOGRAPHS Pursuant to 47 CFR 2.1033(c)12 Figure 9-1: Top Side of PCB. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 9 SHEET 2 OF 3 Figure 9-2: Bottom Side of PCB. Figure 9-3: Top View of chassis. Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 9 SHEET 3 OF 3 Figure 9-4: Bottom View of chassis.

SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 1 of 11 Certificate Number: 1449-01 FCC ID: AZ489FT4873 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 CGISS EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: December 17, 2004 Report Revision: Rev. O Report ID: FCC rpt_AlphaL UHF_Rev O_041217 SR1761 Responsible Engineer: Jim Fortier (Elect. Principal Staff Eng.) Date/s Tested: 12/8/04 -12/9/04 Manufacturer/Location: Motorola Sector/Group/Div.: CGISS/GTDG DUT Description: Portable, PTT, Alpha L UHF 4W 450-470Mhz, 16ch, Black Test TX mode(s): CW Max. Power output: 4.5 Watts Nominal Power: 4.0 Watts Tx Frequency Bands: 450-470 MHz Signaling type: FM Model(s) Tested: PMUE2384A Model(s) Certified: PMUE2384A Serial Number(s): 027YEU0107 Classification: Occupational/Controlled Rule Part(s): 90.210 Approved Accessories: Antenna(s): PMAE4020A (Alpha L antenna 450-470MHZ ¼ wave, 9cm, -3dBi) Battery(ies): PMNN4071A (NiMH battery) Body worn accessory: RLN5644A (Spring Belt clip); PMLN4691A (Standard Belt clip) Audio Accessories: PMMN4008A (RSM); PMLN4442A (Earbud w/ in-line mic & PTT/VOX switch); PMLN4443A (Ear receiver w/ in-line mic & PTT/VOX switch; PMLN4444A (Earphone Boom mic w/ in-line mic & PTT/VOX switch); PMLN4445A (Ultra lightweight headset w/ in-line PTT/VOX switch) Max. Calc. 1-g/10-g Avg. SAR: 5.38/3.91 W/kg (Head/Face); 7.37/5.19 W/kg (Body) Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 2.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. This reporting format is consistent with the test report guidelines of the TIA TSB-150 December 2004 The results and statements contained in this report pertain only to the device(s) evaluated. Signature on file Ken Enger CGISS EME Lab Senior Resource Manager, Laboratory Director, Certification Date: 12/17/04 PRFEECT Certificate No.: L1041245 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 2 of 11 Part 1 of 2 Introduction and Overview ................................................................................................ 3 2.0 References, Standards, and Guidelines ........................................................................ 3 2.1 SAR Limits ............................................................................................................... 4 3.0 Description of Device Under Test (DUT).................................................................... 4 4.0 Description of Test System .......................................................................................... 5 4.1 Description of Robotics/Probes/Readout Electronics ............................................... 5 4.2 Description of Phantom(s) ........................................................................................ 5 4.3 Description of Equivalent Tissues ............................................................................ 6 5.0 Additional Test Equipment ......................................................................................... 6 6.0 SAR Measurement System Verification ..................................................................... 7 6.1 Equivalent Tissue Test results.................................................................................. 7 6.2 System Check Test results ....................................................................................... 7 7.0 DUT Test Strategy and Methodology ......................................................................... 8 7.1 Test Plan................................................................................................................... 8 7.2 Device Positioning Procedures ................................................................................ 9 8.0 Environmental Test Conditions................................................................................... 9 9.0 Test Results Summary................................................................................................. 9 9.1 Highest S.A.R. results calculation methodology.................................................... 11 10.0 Conclusion ...............................................................................................................11 Part 2 of 2 Appendices A. Measurement Uncertainty.............................................................2 B. Probe Calibration Certificates........................................................5 C. Dipole Calibration Certificates.......................................................15 D. Test System Verification Scans......................................................20 E. DUT Scans (Shortened scans & highest SAR configurations)..................25 F. DUT Supplementary Data (e.g. Power Slump)....................................30 G. DUT Test Position Photos............................................................31 H. DUT & Accessory Photos............................................................34 I. DUT Body-worn Separation Distances.............................................35 REVISION HISTORY Date Revision Comments 12/17/04 O Release of Prototype results SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 3 of 11 1.0 Introduction and Overview This report details the utilization, test setup, test equipment, and test results of the Specific Absorption Rate (S.A.R.) measurements performed at the CGISS EME Test Lab for model number PMUE2384A, FCC ID: AZ489FT4873. The test results presented herein clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8.0 mW/g per the requirements of 47 CFR 2.1093(d). 2.0 Reference Standards and Guidelines This product is designed to comply with the following national and international standards …

Text truncated - open the document above for the full version.

SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 1 of 35 Certificate Number: 1449-01 FCC ID: AZ489FT4873 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 CGISS EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: December 17, 2004 Report Revision: Rev. O Report ID: FCC rpt_AlphaL UHF_Rev O_041217 SR1761 Responsible Engineer: Jim Fortier (Elect. Principal Staff Eng.) Date/s Tested: 12/8/04 -12/9/04 Manufacturer/Location: Motorola Sector/Group/Div.: CGISS/GTDG DUT Description: Portable, PTT, Alpha L UHF 4W 450-470Mhz, 16ch, Black Test TX mode(s): CW Max. Power output: 4.5 Watts Nominal Power: 4.0 Watts Tx Frequency Bands: 450-470 MHz Signaling type: FM Model(s) Tested: PMUE2384A Model(s) Certified: PMUE2384A Serial Number(s): 027YEU0107 Classification: Occupational/Controlled Rule Part(s): 90.210 Approved Accessories: Antenna(s): PMAE4020A (Alpha L antenna 450-470MHZ ¼ wave, 9cm, -3dBi) Battery(ies): PMNN4071A (NiMH battery) Body worn accessory: RLN5644A (Spring Belt clip); PMLN4691A (Standard Belt clip) Audio Accessories: PMMN4008A (RSM); PMLN4442A (Earbud w/ in-line mic & PTT/VOX switch); PMLN4443A (Ear receiver w/ in-line mic & PTT/VOX switch; PMLN4444A (Earphone Boom mic w/ in-line mic & PTT/VOX switch); PMLN4445A (Ultra lightweight headset w/ in-line PTT/VOX switch) Max. Calc. 1-g/10-g Avg. SAR: 5.38/3.91 W/kg (Head/Face); 7.37/5.19 W/kg (Body) Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 2.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. This reporting format is consistent with the test report guidelines of the TIA TSB-150 December 2004 The results and statements contained in this report pertain only to the device(s) evaluated. Signature on file Ken Enger CGISS EME Lab Senior Resource Manager, Laboratory Director, Certification Date: 12/17/04 Certification No.: L1041245 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 2 of 35 APPENDIX A Measurement Uncertainty SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 3 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 4 of 35 Notes for Tables 1 and 2 a) Column headings a-k are given for reference. b) Tol. - tolerance in influence quantity. c) Prob. Dist. – Probability distribution d) N, R - normal, rectangular probability distributions e) Div. - divisor used to translate tolerance into normally distributed standard uncertainty f) ci - sensitivity coefficient that should be applied to convert the variability of the uncertainty component into a variability of SAR. g) ui – SAR uncertainty h) vi - degrees of freedom for standard uncertainty and effective degrees of freedom for the expanded uncertainty. SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 5 of 35 Appendix B Probe Calibration Certification SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 6 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 7 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 8 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 9 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 10 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 11 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 12 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 13 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 14 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 15 of 35 Appendix C Dipole Calibration Certificates SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 16 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 17 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 18 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 19 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 20 of 35 Appendix D Test System Verification Scans SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 21 of 35 SPEAG 450 MHz Dipole; Model D450V2, SN 1001; Test Date: 12/08/04 Motorola CGISS EME Lab Run #: Sys Perf-R1-041208-01 TX Freq: 450 MHz Sim Tissue Temp: 20.6 C Start Power: 250mW SAR target at 1W is 4.58 mW/g (1g avg, including drift) SAR target at 1W is 3.13 mW/g (10g avg, including drift) SAR calculated 1g is 4.50 mW/g percent from target (including drift) is - 1.76 % SAR calculated 10g is 2.97 mW/g Percent from target (including drift) is - 4.98 % Flat Phantom; Probe: ET3DV6 - SN1547(Cal Date 29 Sept 2004); ConvF(7.10,7.10,7.10); Probe cal date: 29/9/04; Crest factor: 1.0; FCC Body 450 MHz: σ = 0.92 mho/m εr = 55.6 ρ = 1.00 g/cm3; DAE3: SN:363 (5/26/04) Cubes (2): SAR (1g): 1.13 mW/g ± 0.04 dB, SAR (10g): 0.747 mW/g ± 0.04 dB, (Worst-case extrapolation) Coarse: Dx = 15.0, Dy = 15.0, Dz = 10.0; Max at 33.0, 75.0, 4.7 Power drift: 0.02 dB SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 22 of 35 SPEAG 450 MHz Dipole; Model D450V2, SN 1001; Test Date: 12/09/04 Motorola CGISS EME Lab Run #: Sys Perf-R1-041209-01 TX Freq: 450 MHz Sim Tissue Temp: 20.6 C Start Power: 250mW SAR target at 1W is 4.58 mW/g (1g avg, including drift) SAR target at 1W is 3.13 mW/g (10g avg, including drift) SAR calculated 1g is 4.59 mW/g percent from target (including drift) is + 0.21 % SAR calculated 10g is 2.97 mW/g Percent from target (including drift) is - 3.3 % Flat Phantom; Probe: ET3DV6 - SN1547(Cal Date 29 Sept 2004);Probe Cal Date: 29/9/04ConvF(7.10,7.10,7.10); Crest factor: 1.0; FCC Body 450 MHz: σ = 0.92mho/m ε r = 55.4 ρ = 1.00 g/cm3; DAE3: SN:363 (5/26/04) Cubes (2): Peak: 1.77 mW/g ± 0.02 dB, SAR (1g): 1.15 mW/g ± 0.02 dB, SAR (10g): 0.759 mW/g ± 0.03 dB, (Worst-case extrapolation)Penetration depth: 12.7 (11.4, 14.3) [mm] Power drift: 0.01 dB SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 23 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 24 of 35 SR1761 CGISS EME Form-SAR-Rpt-Rev. 4.00 Page 25 of 35 Appendix E DUT Scans (Shortened scans & Highest SAR configurations) SR1761 CGISS EME Form-SAR-Rpt…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: AZ489FT4873 EXHIBIT 6 SHEET 1 OF 26 EXHIBIT 6 INDEX OF SUBMITTED MEASURED DATA This exhibit contains the measured data for this equipment as follows: EXHIBIT 6A – RF Power Output (Table) EXHIBIT 6B – Transmit Audio Frequency Response (2 Graphs) 6B-1 –12.5 kHz Channel Spacing 6B-2 –25 kHz Channel Spacing EXHIBIT 6C – Transmit Audio Low Pass Filter Response (2 Graphs) 6C-1 –12.5 kHz Channel Spacing 6C-2 –25 kHz Channel Spacing EXHIBIT 6D – Modulation Limiting (6 Graphs) 6D-1 –12.5 kHz Channel Spacing, Carrier Squelch (CSQ) Mode 6D-2 –12.5 kHz Channel Spacing, Tone Private Line (TPL) Mode 6D-3 –12.5 kHz Channel Spacing, Digital Private Line (DPL) Mode 6D-4 –25 kHz Channel Spacing, Carrier Squelch (CSQ) Mode 6D-5 –25 kHz Channel Spacing, Tone Private Line (TPL) Mode 6D-6 –25 kHz Channel Spacing, Digital Private Line (DPL) Mode EXHIBIT 6E – Occupied Bandwidth (6 Spectrum Analyzer Plots) 6E-1 –12.5 kHz Channel Spacing, 2500 Hz Audio Modulation Only 6E-2 –12.5 kHz Channel Spacing, 2500 Hz Audio and PL Tone Modulation 6E-3 –12.5 kHz Channel Spacing, 2500 Hz Audio and DPL Tone Modulation 6E-4 –25 kHz Channel Spacing, 2500 Hz Audio Modulation Only 6E-5 –25 kHz Channel Spacing, 2500 Hz Audio and PL Tone Modulation 6E-6 –25 kHz Channel Spacing, 2500 Hz Audio and DPL Tone Modulation EXHIBIT 6F – Conducted Spurious Emissions (12 Tables) 6F-1 - 1 Watts Harmonic of Carrier 450.025 MHz, 12.5 kHz Channel Spacing 6F-2 - 1 Watts Harmonic of Carrier 460.025 MHz, 12.5 kHz Channel Spacing 6F-3 - 1 Watts Harmonic of Carrier 469.975 MHz, 12.5 kHz Channel Spacing 6F-4 – 4 Watts Harmonic of Carrier 450.025 MHz, 12.5 kHz Channel Spacing 6F-5 – 4 Watts Harmonic of Carrier 460.025 MHz, 12.5 kHz Channel Spacing 6F-6 – 4 Watts Harmonic of Carrier 469.975 MHz, 12.5 kHz Channel Spacing 6F-7 - 1 Watts Harmonic of Carrier 450.025 MHz, 25 kHz Channel Spacing 6F-8 - 1 Watts Harmonic of Carrier 460.025 MHz, 25 kHz Channel Spacing 6F-9 - 1 Watts Harmonic of Carrier 469.975 MHz, 25 kHz Channel Spacing 6F-10 – 4 Watts Harmonic of Carrier 450.025 MHz, 25 kHz Channel Spacing 6F-11 – 4 Watts Harmonic of Carrier 460.025 MHz, 25 kHz Channel Spacing 6F-12 – 4 Watts Harmonic of Carrier 469.975 MHz, 25 kHz Channel Spacing EXHIBIT 6G – Radiated Spurious Emissions (12 Graphs) 6G-1 – 4 Watts, 450.025 MHz, 12.5 kHz Channel Spacing 6G-2 – 4 Watts, 465.025 MHz, 12.5 kHz Channel Spacing 6G-3 – 4 Watts, 469.975 MHz, 12.5 kHz Channel Spacing 6G-4 – 4 Watts, 450.025 MHz, 25 kHz Channel Spacing 6G-5 - 4 Watts, 460.025 MHz, 25 kHz Chan…

Text truncated - open the document above for the full version.