AZ489FT4891PORTABLE TRANSMITTER (CLP)

M Congratulations on your new radio! Your radio is ready to use after a fully-charged battery has been installed and it is connected to an appropriate audio accessory. Please refer to www.motorola.com for information on approved accessories. CLP Series professional two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission (FCC). In order to transmit on these frequencies, you are required to have a license issued by the FCC. http://www.fcc.gov This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. GETTING STARTED 1. INSTALL THE BATTERY • Push up the latch at the bottom of the battery door and lift the battery door off the radio. • Align the battery contacts with tabs in the battery compartment. Insert the contact side of the battery first, then press the battery down to secure in place. • Put the battery door back on the radio. Push down the latch to lock. 2. CHARGE THE BATTERY Connect the power supply to the drop-in charging tray or multi-unit charger and insert the radio into the tray. The light on the charger is red when the radio is charging. It turns to green once the radio is fully charged. QUICK REFERENCE CLP SERIES™ PORTABLE RADIO Push-to-Talk (PTT) Button Menu Button Power/Battery Button Accessory Connecto r Volume Control (+/-) Smart Status Glow 3. CONNECT AN AUDIO ACCESSORY Connect a wired audio accessory or pair with a wireless accessory (select models only). 4. TURN THE RADIO ON Press and hold the Power/Battery button until you hear a short tone and the Smart Status Glow lights up. (To turn off, press and hold the button until you hear a short tone.) 5. CHECK BATTERY STATUS When powered on, short press and release the Power/Battery button, the Smart Status Glow gives you the battery status: Green – high level Yellow – medium level Red – low level Red blink – critical After the Smart Status Glow indicates the BATTERY STATUS, it will return to the current channel color. TRANSMITTING AND RECEIVING 1. Turn radio on and set volume level by pressing volume control. A total of 16 volume levels are available from 1 to 16. 2. To talk, press and hold the PTT button on the front of the radio. Speak clearly into the microphone on the audio accessory. When finished talking, release the PTT to listen. 3. To receive, listen through the earpiece at the volume level you have set. Press the PTT to respond. NOTE: CLP Series radios always require the use of an audio accessory with microphone and speaker. OPERATION WITH DEFAULT MENU SETTING: Menu Item 1: Channel Menu Item 2: Monitor Menu Item 3: Scan Menu Item 4: Call Tone (OFF is default) NOTE: For single channel models, only Monitor is available from Menu list. To activate, press and hold the Menu Button; to deactivate, press and hold the Menu Button again. For further information, refer to your specific product User Guide. For product-related questions, please call: 1-800-448-6686 or visit www.motorola.com ATTENTION Before using this product, read the RF energy awareness information and operating instructions contained in the Safety and RF Energy Exposure Booklet enclosed with your radio package. MOTOROLA, the Stylized M Logo, are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. 2009. All rights reserved. Printed in Malaysia.

FCC ID: AZ489FT4891 GENERAL INFORMATION I. Production Plans—Pursuant 2.983 (c). Quantity production is planned. II. Application References -- Pursuant 2.1061 Reference is made to the following Motorola “Application References” 1. Portable Products and their application. 2. Portable Products Transmitter Modulations Methods. III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ Rules. EXHIBIT 1B

FCC ID: AZ489FT4891 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 29 th December 2009. Authorization and Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia. MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4891. Gentlemen: Motorola Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is primarily intended to be use in a portable radio application with capabilities for clear communications with transmit output power of 1.0 Watts (Nominal). The Comfortable, Lightweight, and Portable (CLP) UHF model is as follows: 4 channels with a fixed internal antenna, no-display, and available in colors Black or Red. The subject transmitter complies with Section 90.203 of the rules in that the operator cannot directly program transmit frequencies using only the unit’s normally accessible external controls. Enclosed is a complete Certification Application. Contact me (954) 723-5793, if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Mgr, Regulatory Compliance Mail: [email protected]

EXHIBIT 13B FCC ID: AZ489FT4891 REQUEST FOR CONFIDENTIALITY Date: 29 th December 2009 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4891 Dear Sir / Madam, Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune-Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits should be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ489FT4891 EXTERNAL PHOTOGRAPHS: 1 Front view of Radio 2 Rear view of radio without battery cover. 3 Magnified view of FCC Label. EXHIBIT 3 FCC ID: AZ489FT4891 EXHIBIT 3-A FCC ID: AZ489FT4891 EXHIBIT 3-B FCC ID: AZ489FT4891 EXHIBIT 3-C

FCC ID: AZ489FT4891 IDENTIFICATION LABEL LOCATION X See the attached photograph, and Exhibit 3-D for the location of the Label on the device. Back of Radio Back of Radio under Belt Clip Please note that Motorola complies with FCC Rule Part 2.925 (d) that the label is permanently affixed and is readily visible to the purchaser at the time of purchase. TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/ inch. The label is laser etched into the Urethane paint, exposing the Nickel plating on the Zamak casting substrate. Since no adhesive is required, the label is permanent and tamper-proof. (** - NOTE- The label attached below is a paper polyester film laminate, as described above. This is just for sample purposes, as the actual label is laser etched into the casting) MARKINGS (TEXT) See Photograph, Exhibit 1. EXHIBIT 1

FCC ID: AZ489FT4891 INTERNAL PHOTOGRAPHS: Printed Circuit Board 1 Component (Front side) 2 components (Rear) EXHIBIT 9 FCC ID: AZ489FT4891 EXHIBIT 9-A FCC ID: AZ489FT4891 EXHIBIT 9-B

FCC ID: AZ489FT4891 In accordance with FCC KDB 447498 D01 V04 section 5b Table 1 threshold guidelines for controlled environments, reporting of test results is not required given the separation distances and max power characteristics of the radio as compared to the threshold table. The radio is 1.1 Watt maximum power and with a 50% duty cyle the power would be 550mW which meets the “Body-worn> 1.5 cm” requirements of the table below. Please note that a separation distance of 1.4 - 2.0cm is measured when using the offered belt clip with this radio. b) Portable PTT devices i) The power thresholds and operating conditions in Table 1 are used to determine SAR test requirements for PTT radios required to comply with the general population exposure limit. When the occupational exposure limit applies, these power thresholds are increased by a factor of five (5) to determine the test requirements. SAR is required for PTT devices with maximum output power greater than these thresholds. Table 1 - SAR Evaluation Power Thresholds for PTT devices, f ≤ 0.5 GHz Exposure Conditions mW Held to face ≥ 2.5 cm 250 Body-worn ≥ 1.5 cm 200 Body-worn ≥ 1.0 cm 150 Notes: 1. The time-averaged output power, corresponding to the required PTT duty factor, is compared with these thresholds. 2. The closest distance between the user and the device or its antenna is used to determine the power thresholds. Exhibit 11

FCC ID: AZ489FT4891 Test Report MEASUREMENT EXHIBIT NUMBER OF PAGES I RF Power Output 6A 1 II Audio Response 6B 1 A. 1 Watt 12.5/25 kHz III Modulation Limiting 6C 1 A. 1 Watt 12.5/25 kHz I V Occupied Bandwidth 6D 1-4 5 V Radiated Spurious Emission 1Watt A. TX Vertical / Horizontal 6E 1-4 4 VI Frequency Stability 2 A. Temperature 6F 1 B. Frequency vs. Voltage 6F 2 VII Transient Frequency Behavior 6G1-4 4 EXHIBIT 6 FCC ID: AZ489FT4891 RF POWER OUTPUT DATA The RF power output was measured with the indicated voltage applied to and current into the final RF amplifying device. 1.0 Watt Frequency 464.5500 MHz Measured Conducted RF output* 1. 0 Watts Normal DC Voltage 3.70 Volts Normal DC Current 750 milli amps Primary Supply Voltage 3.80 Volts *Note: RF Conducted output power measured at 3.80Volts EXHIBIT 6A FCC ID: AZ489FT4891 Audio Response 12.5/25 kHz Tx Audio Response (Black Diam ond UHF 1W, Rev A, 12.5kHz chsp) -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 100100010000 Audio Freq (Hz) deviation ratio (dB) Data LL UL 12.5 kHz Tx Audio Response (Black Diam ond UHF, Rev A, 25kHz chsp) -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 100100010000 Audio Freq (Hz) deviation ratio (dB) Dat a LL UL 25 kHz EXHIBIT 6B FCC ID: AZ489FT4891 MODULATION LIMITING 12.5/25 kHz Modulation Limiting (Black Diamond UHF 1W, Rev A, 12.5kHz chsp) 0 500 1000 1500 2000 2500 -25-20-15-10-50510152025 input le ve l (dB) Deviation (Hz) 300Hz 1kHz 3kHz UL 12.5 kHz Modulation Limiting(Black Diamond UHF 1W, Rev A, 25kHz chsp) 0 1000 2000 3000 4000 5000 6000 -25-20-15-10-50510152025 input level (dB) Deviation (Hz) 300Hz 1kHz 3kHz UL 25 kHz EXHIBIT 6C FCC ID: AZ489FT4891 OCCUPIED BANDWIDTH DATA 1 Watt 12.5/25 kHz Channel Spacing EXHIBIT 6D-1 2500 Hz Audio Modulation Emission Type: 11K0F3E Specification Mask D, 90.210 – 12.5 kHz EXHIBIT 6D-2 2500 Hz Audio Modulation Emission Type: 16K0F3E Specification Mask B, 90.210 – 25 kHz EXHIBIT 6D-3 2500 Hz & 77Hz Tone “PL” Modulation Emission Type: 11K0F3E Specification Mask D, 90.210 – 12.5 kHz EXHIBIT 6D-4 2500 Hz & 77Hz Tone “PL” Modulation Emission Type: 16K0F3E Specification Mask B, 90.210 – 25 kHz CARSON’S RULE: 11K0F3E BW= 2(M+D) BW=2 (3 kHz maximum modulation frequency +2.5 kHz deviation) BW=2 (5.5) BW= 11K0 CARSON’S RULE: 16K0F3E BW= 2(M+D) BW=2 (3 kHz maximum modulation frequency +5 kHz deviation) BW=2 (8) BW= 16K0 EXHIBIT 6D FCC ID: AZ489FT4891 1- Watt 12.5 kHz Mask D, Rule Part: 90.210 Emission Type: 11K0F3E Sideband Spectrum 2.5kHz tone mod -no PL (Black Diamond UHF Re v A 1W, 12.5k Hz chs p ) span 110kHz, res bw==100Hz, video bw=3kHz -50.00 -45.00 -40.00 -35.00 -30.00 -25.00 -20.00 -15.00 -10.00 -5.00 0.00 5.00 10.00 15.00 20.00 25.00 30.00 449.9450449.9500449.9550449.9600449.9650449.9700449.9750449.9800449.9850449.9900449.9950450.0000450.0050450.0100450.0150450.0200450.0250450.0300450.0350450.0400450.0450450.0500450.0550 frequency (MHz) Power (dBm) unmodulated 2.5kHz tone SPECS EXHIBIT 6D-1 FCC ID: AZ489FT4891 1- Watt 25 kHz Mask B, Rule Part: 90.210 Emission Type: 16K0F3E Sideband Spectrum 2.5kHz tone mod no PL (Black Diamond UHF Rev A , 1W, 25kHz chsp ) span 110kHz, res BW=100Hz, video BW=3kHz -50.00 -45.00 -40.00 -35.00 -30.00 -25.00 -20.00 -15.00 -10.00 -5.00 0.00 5.00 10.00 15.00 20.00 25.00 30.00 449.9450449.9500449.9550449.9600449.9650449.9700449.9750449.9800449.9850449.9900449.9950450.0000450.0050450.0100450.0150450.0200450.0250450.0300450.0350450.0400450.0450450.0500450.0550 frequency (MHz) Power (dBm) unmodulated 2.5kHz tone SPECS EXHIBIT 6D-2 FCC ID: AZ489FT4891 1- Watt 12.5 kHz 2500 Hz & 77Hz Tone “PL” Modulation Mask D, Rule Part: 90.210 Emission Type: 11K0F3E Sideband Spectrum 2.5kHz tone mod with PL (Black Diamond UHF Rev A , 1W, 12.5kHz chs p ) span 110kHz, res bw=300Hz, v ideo bw=3kHz -50.00 -45.00 -40.00 -35.00 -30.00 -25.00 -20.00 -15.00 -10.00 -5.00 0.00 5.00 10.00 15.00 20.00 25.00 30.00 449.9450449.9500449.9550449.9600449.9650449.9700449.9750449.9800449.9850449.9900449.9950450.0000450.0050450.0100450.0150450.0200450.0250450.0300450.0350450.0400450.0450450.0500450.0550 frequency (MHz) Power (dBm) unmodulated 2.5kHz tone SPECS EXHIBIT 6D-3 FCC ID: AZ489FT4891 1- Watt 25 kHz 2500 Hz & 77 Hz Tone “PL” Modulation Mask B, Rule Part: 90.210 Emission Type: 16K0F3E Sideband Spectrum 2.5kHz tone mod with PL (Black Diamond UHF Rev A , 1W, 25k Hz chs p ) span 110kHz, res BW=100Hz, video BW=3kHz -50.00 -45.00 -40.00 -35.00 -30.00 -25.00 -20.00 -15.00 -10.00 -5.00 0.00 5.00 10.00 15.00 20.00 25.00 30.00 449.9450449.9500449.9550449.9600449.9650449.9700449.9750449.9800449.9850449.9900449.9950450.0000450.0050450.0100450.0150450.0200450.0250450.0300450.0350450.0400450.0450450.0500450.0550 frequency (MHz) Power (dBm) unmodulated 2.5kHz tone SPECS EXHIBIT 6D-4 FCC ID: AZ489FT4891 1Watt Motorola Inc. Transmit Radiated Spurious Emissions: CLP with Battery BT60 Tx Power: 1.1 Watts 451.1875 MHz Frequency (MHz)FCC Failing Limit (dBm) Horizontal Measured Emission Equiv. Pwr Into Ideal Dipole (dBm) Vertical Measured Emission Equiv Pwr Into Ideal Dipole (dBm) 902.3750 -20-53.43-49.55 1353.5625-20-42.10-41.52 1804.7500-20-63.90-56.63 2255.9375-20-65.94-61.77 2707.1250-20-62.54-59.49 3158.3125-20-65.24-59.57 3609.5000-20-60.71-56.55 4060.6875-20-63.32-57.25 4511.8750-20-61.73* CLP with Battery BT60 Tx Power: 1.1 Watts 461.0625 MHz Frequency (MHz)FCC Failing Limit (dBm) Horizontal Measured Emission Equiv. Pwr Into Ideal Dipole (dBm) Vertical Measured Emission Equiv Pwr Into Ideal Dipole (dBm) 922.1250 -20** 1383.1875-20-60.33-57.79 1844.2500-20-63.33-63.39 2305.3125-20-58.75-53.29 2766.3750-20-56.45-51.71 3227.4375-20-63.88-57.43 3688.5000-20-55.32-54.89 4149.5625-20-60.16-54.40 4610.6250-20** * Indicates the spurious emission could not be detected due to noise limitations or ambients. The data presented here was taken using the substitution method as found in the TIA/EIA-603 document. Motorola Plantation EMC Lab – Test Performed by: Curt Mc Lennan FCC Registration: 91932 / Indu…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT4891 TEST SET- UP PROCEDURES Except where otherwise stated, all measurements are made following the Electronic Industries Association (EIA) Minimum Standard for Portable/Personal Land Mobile Communications FM or PM Equipment 25-1000 MHz-(TIA/EIA-603). This exhibit presents a brief summary of how the measurements were made, the required limits, and the test equipment used. The following procedures are presented with this application. 1. RF Power Output X 2. Audio Response X 3. Low Pass Filter Response X 4. Modulation Limiting X 5. Occupied Bandwidth X 6. Radiated Spurious Emissions X 7. Conducted Spurious Emissions X 8. Frequency Stability X 9. Transient Frequency Behavior X EXHIBIT 7 FCC ID: AZ489FT4891 TEST EQUIPMENT LIST Pursuant To FCC Rules 2.999 1. Spectrum Analyzer A. HP 8591E B. HP 8566 C. HP35665A 2. RF Signal Generators A. HP 8665 B. HP 8642 C. HP 8656 3. RF Millivoltmeter A. Boonton 4200 B. Boonton 4210 4. RF Loads A. WEINSCHEL M1418 5. Dipole Antenna Set A. Singer DM-105A series B. EMCO Model 3120 6. RF Power Meters A. HP 436A B. 8482B Power Sensor C. 30 dB High Power Pad 7. Monitor Receivers A. Motorola Comm Syst Analyzer B. HP8901 8. Tenny Temperature Chamber 9. Frequency Counters a. HP 5385A 10. Audio Analyzer a. HP8903B 11. AC/DC Voltmeters a. Fluke8012A Digital Multimeter 12. HP8901B Modulation Analyzer EXHIBIT 7 FCC ID: AZ489FT4891 RF POWER OUTPUT Pursuant to FCC Rules 2.985 (a) Method of Measurement The RF power output is measured with the value of voltage and current specified in Exhibit 3 as required by 2.983(d) (5). A 50 ohm RF attenuator of proper power rating was used as a load for making these measurements. For Transmitter having output impedance other than 50 ohm, a suitable matching network is placed between the transmitter and the load. The power measurements are made using a Hewlett Packard series HP 436A power meter and a 30 dB attenuator or a HP 437B power meter. AUDIO FREQUENCY RESPONSE Pursuant FCC Rules 2.987 (a) Method of Measurement Operate the transmitter under standard test conditions and monitor the output with a frequency deviation meter or calibrated test receiver. With 1000 Hz sine wave audio input applied through a dummy microphone circuit, adjust the audio input to give 30% of full rated system deviation maintaining constant deviation, vary the input frequency from 100 to 5000 Hz, and observe the level necessary to maintain a constant 30% modulation. Minimum Standard The audio frequency response shall not vary more than +1 or -3 dB from 300 to 3000 Hz as referenced to 1000 Hz level (with the exception of a permissible 6 dB/octave roll off from 2500 to 3000 Hz) POST LIMITER FILTER FREQUENCY RESPONSE Pursuant FCC Rules 2.987 (a) EXHIBIT 7 FCC ID: AZ489FT4891 FCC Limits —per applicable rule parts. A. 25 to 450 MHz Frequencies between 3 kHz and 15 kHz shall be attenuated greater than the attenuation at 1 kHz by 40 log 10 (f/3) dB. Frequencies above 15 kHz shall be attenuated 28 dB. B. 450 to 866 MHz Frequencies between 3 kHz and 20 kHz shall be attenuated greater than the attenuation at 1 kHz by 60 1og 10 (f/3) dB. Frequencies above 20 kHz shall be attenuated at least 50 dB. MODULATION LIMITING Pursuant FCC Rules 2.987 (a) Method of Measurement The transmitter shall be adjusted for full rated system deviation. Adjust the audio input for 60% of rated system deviation at 1000 Hz. Using this level as a reference (0 dB) vary the audio input level from the reference to a level 20 dB above it for modulation frequencies of 300, 1000 and 3000 Hz. Record the system deviation obtained as a function of the input level. FCC Limits Minimum Standard - The transmitter modulation must not exceed rated system deviation at any audio frequency input or reasonable change in input level. OCCUPIED BANDWIDTH Pursuant to FCC Rules 2.989 Method of Measurement Data on occupied bandwidth is presented in the form of a spectrum analyzer photograph, which illustrates the transmitter sidebands. A photograph is taken of the unmodulated carrier, for reference, to which is superimposed the sideband display generated by modulating the carrier with a 2500 Hz tone at a level 16 dB greater than that required to produce 50 percent modulation. If tone or digital coded squelch is indicated, photographs using both the 2500 Hz tone and the indicated squelch signal are used to modulate the transmitter. During these measurements, the instantaneous Deviation Control is set for a maximum of +2.5 kHz. EXHIBIT 7 FCC ID: AZ489FT4891 FCC Limits - Per Applicable Rule Parts. Measured Data: On any frequency removed from the assigned frequency up to 5.625 kHz, the spec is 0 dB. On any frequency removed from the assigned frequency from 5.625 kHz up to and including 12.5 kHz, the spec is at least 7.27(fd-2.88 kHz) dB down. On any frequency removed from the assigned frequency by more than 12.5 kHz, the spec is at least 50+10log(P) dB (mean output power in watts) or 70 decibels whichever is the lesser attenuation. RADIATED SPURIOUS EMISSIONS Pursuant to FCC Rules 2.993 Test Site: The site, located at Plantation, Florida in a region, which is reasonably free from RF interference and has been approved by the Commission for Spurious Measurements. The equipment is placed on the turntable and then placed in normal operation using the intended power source. A broadband receiving antenna located 15 ft. from the transmitter picks up any signal radiated from the transmitter and its operation accessories. The antenna is adjustable in height and can by horizontally and vertically polarized. A spectrum analyzer covering the necessary frequency range is used to detect and measure any radiation picked up by the antenna. CONDUCTED SPURIOUS EMISSIONS Pursuant to FCC Rule 2.991 Method of Measurement: The transmitter is terminated into a 50 ohm load and interfaced with a spectrum analyzer, which allows the spurious emission level relative to the carrier level to be measured directly. Modulate the transmitter w…

Text truncated - open the document above for the full version.