AZ489FT4892PORTABLE 2-WAY RADIO WITH BT

APX 6000 User Guide Model 1.5 68012001081-A English mASTRO ® APX™ 6000 Series Digital Portable RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. Radio Controls Radio On/OffZones and Channels Receiving and TransmittingSending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. !  PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 • On – On/Off/Volume knob clockwise. • Off – On/Off/Volume knob counterclockwise. • Zone – Zone switch to desired zone. • Channel – Channel switch to desired channel. PICTURE TO BE REPLACED WITH APX 6000 MODEL 1.5 1 Select zone/channel. 2 Listen for a transmission.ORPress and hold Volume Set button. ORPress Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. 1 Press the Emergency button. 2 The display shows EMERGNCY and the current zone/channel. A short, medium-pitched tone sounds, and the LED rapidly blinks red. 3 When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency. *PMLN5715A* PMLN5715A © 2010 by Motorola, Inc. All Rights Reserved. 06/101301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A. English Sending an Emergency Call To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call To exit emergency at any time, press and hold the Emergency button. Display Status Icons 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency c ontinues until you: Press and hold the Emergency button to exit emergency state.ORPress and release the PTT button to exit silent emergency mode and enter regular emergency (alarm, call, or alarm with call) mode. Blinks when the battery is low.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. The vote scan feature is enabled. U vV O M H OR L i j k On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode Zone Bank 1A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Zone Bank 2D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. m A or B or C D or E or F Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: APX 6000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. Contents English iii ContentsThis User Guide contains all the information you need to use the AP X™ 6000 Series Digital P ortable Radios.Declaration of Conformity . . . . . . . . . . . . . . . . . .iImportant Safety Information . . . . . . . . . . . . . vii P roduct Safety and RF Exposure Compliance . . . vii Software Version . . . . . . . . . . . . . . . . . . . . . . . viiComputer Software Copyrights . . . . . . . . . . .viiiDocumentation Copyrights . . . . . . . . . . . . . . .viiiDisclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viiiGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . .…

Text truncated - open the document above for the full version.

Applicant: Motorola FCC ID: AZ489FT4892 SHEET 1 of 1 EXHIBIT 2 Exhibit 2: Statement of Certification — Pursuant to 47 CFR 2.907 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received an Electrical Engineering degree from Holon Institute of Technology, Israel. 2) I have 3 years experience in developing, testing, and certifying Land Mobile Communications Products. NAME: Borokhovich Eli SIGNATURE: /s/ Eli Borokhovich (signed) DATE: 01/13/2011 POSITION: Electrical Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Bitton Gaby SIGNATURE: /s/ Gaby Bitton (signed) DATE: 01/13/2011 POSITION: Engineering Manager

8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA FCC ID: AZ489FT4892 Date: 25 th January 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4892 Dear Sir or Madam: Motorola, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Portable Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency range: 380 - 470 MHz: 1-5.0 Watts (Nominal) The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. Additionally, the radio is equipped with a Bluetooth transmitter capable of clear communication with fixed power operating within the following frequency ranges: 2.402-2.480 GHz: 7.25 dBm (Nominal) The Bluetooth transmitter complies with the requirements of FCC Part 15 subpart C. A complete application for certification is enclosed; please contact me if you require any additional information. Sincerely, Mike Ramnath /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected] EXHIBIT 13a

8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA REQUEST FOR CONFIDENTIALITY Date: 25 th January 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitters with FCC ID: AZ489FT4892 Dear Sir/Madam: Motorola is requesting that Exhibit 4 (Block Diagram), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune-Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to CFR 47 Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected] EXHIBIT 13b

FCC ID: AZ489FT4892 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 25 th January 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX6000 Portable 2-Way radio was designed to operate in the frequency bands 380-470 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola is requesting that the FCC lists the frequencies 380-470 MHz under FCC Rule Parts 90 on the FCC Grant For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC-OET KDB Publication 634817 guidance, the grantee acknowledges that a device operating on unauthorized frequencies is a violation of the FCC Rules. Frequency Range (MHz) Part 90 Feds 380-406 x 406.1-454 x x 454-456* 467.7375-470 x *Canada Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected] Exhibit 13c

Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 1 of 19 Exhibit 3: External Photographs -- Pursuant to 47 CFR 2.1033(c)(12) The following photographs are attached. H98QDH9PW7AN H98QDF9PW6AN H98QDD9PW5AN (FULL KEYPAD/DISPLAY) (LIMITED KEYPAD) (NO KEYPAD/DISPLAY) 1. Front view. 3A 3.1A 3.2A 2. Back view with battery. 3B 3.1B 3.2B 3. Back view (FCC label location). 3C 3.1C 3.2C 4. Side view (Right). 3D 3.1D 3.2D 5. Side view (Left). 3E 3.1E 3.2E 6. Top view (Controls). 3F 3.1F 3.2E - - Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 2 of 19 1. Front view. 3A Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 3 of 19 2. Back view with battery. 3B Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 4 of 19 3. Back view (FCC label location). 3C Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 5 of 19 4. Side view (Right). 3D Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 6 of 19 5. Side view (Left). 3E Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 7 of 19 6. Top view (Controls). 3F Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 8 of 19 1. Front view. 3.1A Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 9 of 19 2. Back view with battery. 3.1B Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 10 of 19 3. Back view (FCC label location). 3.1C Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 11 of 19 4. Side view (Right). 3.1D Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 12 of 19 5. Side view (Left). 3.1E Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 13 of 19 6. Top view (Controls). 3.1F Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 14 of 19 1. Front view. 3.2A Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 15 of 19 2. Back view with battery. 3.2B Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 16 of 19 3. Back view (FCC label location). 3.2C Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 17 of 19 4. Side view (Right). 3.2D Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 18 of 19 5. Side view (Left). 3.2E Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 3 SHEET 19 of 19 6. Top view (Controls). 3.2E

Applicant: Motorola FCC ID: AZ489FT4892 SHEET 1 of 2 Identification Label LOCATION See the Attached Photograph or Sketch X Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. Applicant: Motorola FCC ID: AZ489FT4892 SHEET 2 of 2 General Information I. Production Plans Quantity production is planned. II. Application References Reference is made to the following Motorola "Application References" 1. Portable Products and their application. 2. Portable Products Transmitter Modulations Methods. 3. Motorola EMC Laboratory-Plantation, Florida III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Subpart J of the Commissions’ rules. IV. Applicable References: • Reference Certification FCC ID: AZ489FT4892 • RSS Gen, RSS102, RSS 119, RSS 210. • EIA/TIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards • CFR 47, Rule Part 2, 15 and 90

Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 1 of 7 Internal Photographs The following photographs are attached. Exhibit 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D 5. Vocon board with Shields (Top). 9E 6. Vocon board without Shields (Top). 9F 7. Vocon board with Shields (Bottom). 9G 8. Vocon board without Shields (Bottom). 9H 9. Expander board with Shields (Top). 9I 10. Expander board without Shields (Top). 9J 11. Expander board with Shields (Bottom). 9K 12. Expander board without Shields (Bottom). 9L Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 2 of 7 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 3 of 7 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 4 of 7 5. Vocon board with Shields (Top). 9E 6. Vocon board without Shields (Top). 9F Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 5 of 7 7. Vocon board with Shields (Bottom). 9G 8. Vocon board without Shields (Bottom). 9H Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 6 of 7 9. Expander board with Shields (Top). 9I 10. Expander board without Shields (Top). 9J Applicant: Motorola FCC ID: AZ489FT4892 EXHIBIT 9 SHEET 7 of 7 11. Expander board with Shields (Bottom). 9K 12. Expander board without Shields (Bottom). 9L Bluetooth chip Bluetooth Antenna

SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 1 of 11 TESTING CERT # 2518.01 Exhibit 7B: SAR Test Report Photographs EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Signature on file – Deanna Zakharia Deanna Zakharia EME Lab Senior Resource Manager, Laboratory Director Approval Date: 1/21/2011 SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 2 of 11 Report Revision History Date Revision Comments 1/21/11 O Initial release SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 3 of 11 1.0 Highest SAR Test Position per body location 1.1 Body PSM PMMN4059A w/ antenna FAF5259A, and 4205823V01 PSM Belt clip against the phantom. Similar position for other PSM and antenna. Separation Distances (mm) PSM kit # Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 12 20 23 PMNN4403A 12 20 23 FAF5259A NNTN7034A 12 19 25 NNTN7038A 12 20 26 PMNN4403A 12 20 26 PMMN4059A PMAE4065A NNTN7034A 12 19 26 NNTN7038A 12 19 25 PMNN4403A 12 19 25 FAF5259A NNTN7034A 12 19 25 NNTN7038A 12 19 26 PMNN4403A 12 19 26 PMMN4061A PMAE4065A NNTN7034A 12 19 26 SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 4 of 11 1.2 Face DUT w/ front side separated 2.5cm from phantom with antenna FAF5259A, and battery PMNN4403A. Similar position for other batteries and antenna. Separation Distances (mm) Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 25 41 43 PMNN4403A 26 35 37 FAF5259A NNTN7034A 26 40 43 NNTN7038A 26 40 42 PMNN4403A 26 36 43 PMAE4065A NNTN7034A 26 40 44 1.3 Head Not applicable. 1.4 Hand Not applicable. 2.5cm SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 5 of 11 2.0 Other SAR tested positions at the body 2.1 Body worn DUT w/ antenna FAF5259A, battery NNTN7038A, audio cable RMN5058A, and body worn HLN6875A against the phantom. Similar position for other batteries, antenna, and without audio cable attached. Separation Distances (mm) Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 0 44 65 PMNN4403A <1 44 65 FAF5259A NNTN7034A 0 43 58 NNTN7038A 0 43 69 PMNN4403A <1 43 69 PMAE4065A NNTN7034A 0 42 68 SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 6 of 11 DUT w/ antenna FAF5259A, battery NNTN7038A, audio cable RMN5058A, and body worn NTN9179A against the phantom. Similar position for other batteries, antenna, and without audio cable attached. Separation Distances (mm) Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 0 66 96 PMNN4403A 0 66 96 FAF5259A NNTN7034A 0 55 75 NNTN7038A 0 67 117 PMNN4403A 0 65 114 PMAE4065A NNTN7034A 0 55 91 SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 7 of 11 2.2 Front Side against phantom Not applicable. 2.3 Back side against phantom Not applicable. 3.0 Other SAR tested position at the face 3.1 Back of DUT at 2.5cm separation DUT w/ back side separated 2.5cm from phantom with antenna FAF5259A, and battery PMNN4403A. Similar position for other batteries and antenna. Separation Distances (mm) Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 28 41 46 PMNN4403A 28 41 46 FAF5259A NNTN7034A 29 42 46 NNTN7038A 29 42 45 PMNN4403A 29 42 45 PMAE4065A NNTN7034A 30 42 48 2.5cm SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 8 of 11 3.2 Front of PSM at 2.5cm separation PSM PMMN4059A with antenna FAF5259A w/ front side of PSM separated 2.5cm from phantom. Similar position for other batteries, antenna, and PSM. Separation Distances (mm) PSM kit # Antenna kit # Battery kit # @ bottom surface of the DUT @ antenna’s base @ antenna’s tip NNTN7038A 27 35 40 PMNN4403A 27 35 40 FAF5259A NNTN7034A 26 34 38 NNTN7038A 26 34 40 PMNN4403A 26 34 40 PMMN4059 A PMAE4065A NNTN7034A 26 34 38 NNTN7038A 26 34 38 PMNN4403A 26 34 38 FAF5259A NNTN7034A 26 34 38 NNTN7038A 26 34 38 PMNN4403A 26 34 38 PMMN4061 A PMAE4065A NNTN7034A 26 34 38 2.5cm SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 9 of 11 4.0 Other SAR tested positions at the head 4.1 Left ear touch Not applicable. 4.2 Left ear tilt Not applicable. 4.3 Right ear touch Not applicable. 4.4 Right ear tilt Not applicable. 5.0 Other SAR tested positions at the hand 5.1 Left side Not applicable. 5.2 Right side Not applicable. 5.3 Top side Not applicable. 5.4 Bottom side Not applicable. 5.5 Back side Not applicable. SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 10 of 11 6.0 DUT and Accessory Photos The purpose of these photos is to illustrate the offered antenna and belt clip accessories. 6.1 Antenna photo: . From left to right: PMAE4065A and FAF5259A 6.2 Body worn accessories DUT Back View Belt Clip NTN9179A Battery NNTN7038A DUT Side View Belt Clip NTN9179A Battery NNTN7038A DUT Back View Belt Clip HLN6875A Battery NNTN7038A DUT Side View Belt Clip HLN6875A Battery NNTN7038A SR8653/8903/8425 EMS EME Form-SAR-Rpt Ex7B-Rev. 2.01 Page 11 of 11 6.3 Tested audio accessories The following pictures represent the samples of the PSM and audio accessories. 6.4 Tested battery accessories Headset RMN5058A From left to right: PMNN4403A, NNTN7038A, NNTN7034A PSM PMMN4061A PSM PMMN4059A

SR8653/8903/8425 EME Form-SAR-Rpt-Rev. 10.03 Page 1 of 84 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1of 2 EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322. Date of Report: 1/21/2011 Report Revision: O Report ID: SAR rpt_H98QDD9PW5AN (MNUE1005A/MNUE1006A) _Rev.O_110121_ SR8653/8903/8425 * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Responsible Engineer: Kim Uong (Principal Staff Eng.) Report Author: Kim Uong (Principal Staff Eng.) Date/s Tested: 7/27/10 - 9/20/10, 10/5/10 – 10/7/10, 10/8/10 – 1/13/11 Manufacturer/Location: Motorola, Reynosa/Schaumburg Sector/Group/Div.: G&PS Date submitted for test: 7/23/10, 8/6/2010 DUT Description: APX6000 UHF R1 380 – 470 MHz, 3-5.7W, 6.25kHz/12.5kHz/25kHz, Basic Top Display Model. Capable of digital and analog FM transmission. Also capable of TDMA transmission and Bluetooth equipped. Test TX mode(s): CW (PTT) for UHF; CW (76.1% duty cycle for Bluetooth) Max. Power output: 5.7 W for UHF; 10 mW for Bluetooth Nominal Power: 5.0 W for UHF; 10 mW for Bluetooth Tx Frequency Bands: 380 - 470 MHz; 2402 – 2480 MHz Signaling type: FM and TDMA (UHF); FHSS (Bluetooth) Model(s) Tested: H98QDD9PW5AN (MNUE1005A/MNUE1006A) Model(s) Certified: H98QDD9PW5AN (MNUE1006A) Serial Number(s): NUE1006A0052, NUE1006A0043, CAI1006KW2 Classification: Occupational/Controlled FCC ID: AZ489FT4892 FCC Rule Part(s): 90 (406.1 - 470 MHz) IC: 109U-89FT4892 IC standard(s): RSS 102 issue 4; Safety Code 6 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Signature on file – Deanna Zakharia Deanna Zakharia EME Lab Senior Resource Manager, Laboratory Director Approval Date: 1/21/2011 Certification Date: Certification No.: SR8653/8903/8425 EME Form-SAR-Rpt-Rev. 10.03 Page 2 of 84 Part 1 of 2 1.0 Introduction.........................................................................................4 2.0 Abbreviations / Definitions.................................................................4 3.0 Referenced Standards and Guidelines ................................................4 4.0 SAR Limits .........................................................................................5 5.0 SAR Result Scaling Methodology ......................................................6 6.0 Description of Device Under Test (DUT) ..........................................6 7.0 Optional Accessories and Test Criteria ..............................................7 7.1 Antennas ....................................................................................7 7.2 Batteries .....................................................................................7 7.3 Body worn Accessories .............................................................8 7.4 Audio Accessories .....................................................................8 8.0 Description of Test System.................................................................8 8.1 Description of Robotics/Probes/Readout Electronics................9 8.2 Description of Phantom(s) .........................................................9 8.2.1 Dual Flat Phantom .........................................................9 8.2.2 SAM Phantom................................................................9 8.2.3 Elliptical Flat Phantom ..................................................9 8.3 Description of Simulated Tissue ..............................................10 9.0 Additional Test Equipment ...............................................................11 10.0 SAR Measurement System Verification ...........................................12 10.1 Equivalent Tissue Test Results ................................................12 10.2 System Check Test Results ......................................................16 11.0 Environmental Test Conditions ........................................................17 12.0 DUT Test Methodology ....................................................................17 12.1 Measurements ..........................................................................17 12.2 DUT Configuration(s)..............................................................17 12.3 DUT Positioning Procedures ...................................................17 12.3.1 Body .............................................................................17 12.3.2 Head .............................................................................18 12.3.3 Face ..............................................................................18 12.4 DUT Test Channels..................................................................18 12.5 DUT Test Plan .........................................................................18 12.5.1 General Test Flowchart................................................19 13.0 DUT Test Data ...…

Text truncated - open the document above for the full version.

SR8653/8903/8425 EME Form-SAR-Rpt-Rev. 10.03 Page 1 of 101 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2of 2 EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322. Date of Report: 1/21/2011 Report Revision: O Report ID: SAR rpt_H98QDD9PW5AN (MNUE1005A/MNUE1006A) _Rev.O_110121_ SR8653/8903/8425 * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Responsible Engineer: Kim Uong (Principal Staff Eng.) Report Author: Kim Uong (Principal Staff Eng.) Date/s Tested: 7/27/10 - 9/20/10, 10/5/10 – 10/7/10, 10/8/10 – 1/13/11 Manufacturer/Location: Motorola, Reynosa/Schaumburg Sector/Group/Div.: G&PS Date submitted for test: 7/23/10, 8/6/2010 DUT Description: APX6000 UHF R1 380 – 470 MHz, 3-5.7W, 6.25kHz/12.5kHz/25kHz, Basic Top Display Model. Capable of digital and analog FM transmission. Also capable of TDMA transmission and Bluetooth equipped Test TX mode(s): CW (PTT) for UHF; CW (76.1% duty cycle for Bluetooth) Max. Power output: 5.7 W for UHF; 10 mW for Bluetooth Nominal Power: 5.0 W for UHF; 10 mW for Bluetooth Tx Frequency Bands: 380 - 470 MHz; 2402 – 2480 MHz Signaling type: FM and TDMA (UHF); FHSS (Bluetooth) Model(s) Tested: H98QDD9PW5AN (MNUE1005A/MNUE1006A) Model(s) Certified: H98QDD9PW5AN (MNUE1006A) Serial Number(s): NUE1006A0052, NUE1006A0043, CAI1006KW2 Classification: Occupational/Controlled FCC ID: AZ489FT4892 FCC Rule Part(s): 90 (406.1 - 470 MHz) IC: 109U-89FT4892 IC standard(s): RSS 102 issue 4; Safety Code 6 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Signature on file – Deanna Zakharia Deanna Zakharia EME Lab Senior R…

Text truncated - open the document above for the full version.