AZ489FT4893Portable Multi-Band 2-way Radio

APX 7000 User Guide Top Display 6875952M01-D English mASTRO ® APX™ 7000 Series Digital Portable RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. Radio Controls Radio On/OffZones and Channels Receiving and TransmittingSending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. !  Top (Orange) Button__________ 2-Position Concentric Switch______________ 3-Position A/B/C Switch __________________ Accessory Connector • On – On/Off/Volume knob clockwise. • Off – On/Off/Volume knob counterclockwise. • Zone – Zone switch to desired zone. • Channel – Channel switch to desired channel. Battery Side Button 1__________Side Button 2__________ PTT Button On/Off/Volume Control Knob 16-Position Select Knob __________ Top Side (Select) Button__________ Main Speaker Top Display Antenna 1 Select zone/channel. 2 Listen for a transmission.ORPress and hold Volume Set button. ORPress Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. 1 Press the Emergency button. 2 The display shows EMERGNCY and the current zone/channel. A short, medium-pitched tone sounds, and the LED rapidly blinks red. 3 When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency. *68007024033* 68007024033-A © 2009 by Motorola, Inc. All Rights Reserved. 03/101301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A. English Sending an Emergency Call To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call To exit emergency at any time, press and hold the Emergency button. Display Status Icons 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency c ontinues until you: Press and hold the Emergency button to exit emergency state.ORPress and release the PTT button to exit silent emergency mode and enter regular emergency (alarm, call, or alarm with call) mode. Blinks when the battery is low.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. The vote scan feature is enabled. U vV O M H OR L i j k On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode Zone Bank 1A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Zone Bank 2D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. m A or B or C D or E or F Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: APX 7000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. Contents English iii ContentsThis User Guide contains all the information you need to use the APX™ 7000 Series Digital Portable Radios. Declaration of Conformity . . . . . . . . . . . . . . . . . .iImportant Safety Information . . . . . . . . . . . . . vii Product Safety and RF Exposure Compliance . . . . vii Software Version . . . . . . . . . . . . . . . . . . . . . . . viiComputer Software Copyrights . . . . …

Text truncated - open the document above for the full version.

English Product Safety and RF Energy Exposure Booklet for Portable Two-Way Radios The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRINSIC SAFETY ON PAGE 10 OF THIS BOOKLET. !  © 2007 by Motorola, Inc. 02/07 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. *6881095C98* 6881095C98-D *NNTN7223A* NNTN7223A 95C98-D.book Page 1 Tuesday, February 27, 2007 4:36 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 95C98-D.book Page 2 Tuesday, February 27, 2007 4:36 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission (FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. 95C98-D.book Page 3 Tuesday, February 27, 2007 4:36 PM 4 English Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation – Human Exposure) Standard, 2003 • ANATEL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300 GHz" and "Attachment to resolution # 303 from July 2, 2002" RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. Guidelines: • DO NOT remove the RF Exposure Label from the …

Text truncated - open the document above for the full version.

APX 7000 User Guide Top Display 6875952M01-D 6875952M01-D_TopD.book Page 1 Tuesday, April 27, 2010 4:32 PM 6875952M01-D_TopD.book Page 2 Tuesday, April 27, 2010 4:32 PM English mASTRO ® APX™ 7000 Series Digital Portable RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. Radio Controls Radio On/OffZones and Channels Receiving and TransmittingSending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. !  Top (Orange) Button__________ 2-Position Concentric Switch______________ 3-Position A/B/C Switch __________________ Accessory Connector • On – On/Off/Volume knob clockwise. • Off – On/Off/Volume knob counterclockwise. • Zone – Zone switch to desired zone. • Channel – Channel switch to desired channel. Battery Side Button 1__________Side Button 2__________ PTT Button On/Off/Volume Control Knob 16-Position Select Knob __________ Top Side (Select) Button__________ Main Speaker Top Display Antenna 1 Select zone/channel. 2 Listen for a transmission.ORPress and hold Volume Set button. ORPress Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. 1 Press the Emergency button. 2 The display shows EMERGNCY and the current zone/channel. A short, medium-pitched tone sounds, and the LED rapidly blinks red. 3 When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency. *68007024033* 68007024033-A © 2009 by Motorola, Inc. All Rights Reserved. 1301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A. 6875952M01-D_TopD.book Page 3 Tuesday, April 27, 2010 4:32 PM English Sending an Emergency Call To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call To exit emergency at any time, press and hold the Emergency button. Display Status Icons 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency c ontinues until you: Press and hold the Emergency button to exit emergency state.ORPress and release the PTT button to exit silent emergency mode and enter regular emergency (alarm, call, or alarm with call) mode. Blinks when the battery is low.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. The vote scan feature is enabled. U vV O M H OR L i j k On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode Zone Bank 1A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Zone Bank 2D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. m A or B or C D or E or F 6875952M01-D_TopD.book Page 4 Tuesday, April 27, 2010 4:32 PM Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: APX 7000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 6875952M01-D_TopD.book Page i Tuesday, April 27, 2010 4:32 PM Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. 6875952M01-D_TopD.book Page ii Tuesday, April 27, 2010 4:32 PM Contents English iii ContentsThis User Guide c…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 2 SHEET 1 OF 1 EXHIBIT 2 CERTIFICATION OF DATA - Pursuant to 47 CFR 2.907 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received an Electrical Engineering degree from University of Technology Malaysia, Malaysia. 2) I have 3 years experience in developing, testing, and certifying Land Mobile Communications Products. NAME: Diong Kah Chen SIGNATURE: /s/ Diong Kah Chen (signed) DATE: March, 02, 2010 POSITION: Electrical Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Ernest Lean SIGNATURE: /s/ Ernest Lean (signed) DATE: March, 02, 2010 POSITION: Engineering Manager

EXHIBIT 13A SHEET 1 FCC ID: AZ489FT4893 25 th March 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4893 Dear Sir or Madam: Motorola Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Type Acceptance of the subject transmitter. This transmitter is intended for use in a Portable 2-Way Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency ranges: 136 - 174 MHz, 1.0 – 6.0 Watts (Nominal) 450 - 520 MHz, 1.0 - 5.0 Watts (Nominal) The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete application for certification is enclosed. If you require any additional information contact Mike Ramnath at (954) 723-5793. Sincerely, /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected]

EXHIBIT 13B SHEET 1 FCC ID: AZ489FT4893 REQUEST FOR CONFIDENTIALITY Date: 23 rd March 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4893 Dear Sir / Madam, Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ489FT4893 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. EXHIBIT 13c 25 th March 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX7000 Portable 2-Way VHF/UHF Range 2 radio was designed to operate in the frequency bands 136-174 and 450-520 MHz. To aid equipment authorization in other countries that accept the United States FCC Grant for Certification, Motorola is requesting that the FCC list the frequencies 136-174 MHz and 450-520 MHz under FCC Rule Parts 80 and 90 on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. In addition, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, “as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Part 80 Feds Grant Notes Emission Designators Rule Part 80 and 90 136-150.8* x EF, BE 11/16K0F3E, 8K10F1D/F1E/F1W and 20K0F1E 150.8-161.6250 x x EF, BE """ 161.6250-161.7750* EF, BE """ 161.7750-173.4 x x EF, BE """ 173.4-174 x EF, BE """ 380-406 x EF, BE """ 406.1-454 x EF, BE """ 454-456* EF, BE """ 467.7375-470 x EF, BE """ 470-512 x EF, BE """ 512-520 x EF, BE """ *Canada Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

8000 West Sunrise Blvd. Plantation. Fl 33322 Page 1 5 th May 2010 Andrew Leimer Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: Form 731 Confirmation Number: EA496374 with FCC ID: AZ489FT4893 Dear Mr. Leimer; Motorola Inc., 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits its response to the 23 rd April 2010 for information in Correspondence Number 38789. Q1) "Ex 1 FCC Label" has the following text: "Application References -- Pursuant 2.1061 Reference is made to the following Motorola “Application References" 1. Portable Products and their application 2. Portable Products Transmitter Modulations Methods 3. Plantation, Florida Antenna Range " FYI 2.1061 was deleted from FCC rules some time ago, therefore to avoid possible misunderstandings about records that should not be listed in modern applications if those three "References" contain info relevant for documenting compliance, please incorporate details within this application (and future filings) accordingly R1) Rule Part 2.1061 was removed from Exhibit 1. Q2) "Ex 1 FCC Label" has the following text: "FCC Federal Regulations Part 47 Sec. 2.1033 – 2.1055" note also per 2.1033(c)(14) relevant data requirements are 2.1046 to 2.1057 - for this and future filings please revise to clarify R2) Replaced Rule Part “2.1033 – 2.1055" with "2.1046 to 2.1057" in Exhibit 1. Q3) EMC / radio report mentions 2.1047 for "Frequency Stability" - however modern 47 CFR has "Modulation characteristics" at 2.1047, and "Frequency stability" at 2.1055 - please revise document (and future filings) to cite 2.1055 not 2.1047 where appropriate AND check / update ALL rule section cites to ensure proper rule is listed with corresponding data 8000 West Sunrise Blvd. Plantation. Fl 33322 Page 2 R3) Exhibit 6 was corrected to reflect the applicable Rule Parts. • Exhibit 6F: Pursuant 47 CFR 2.1047 had changed to Pursuant 47 CFR 2.1053 • Exhibit 6G: Pursuant 47 CFR 2.1047 had changed to Pursuant 47 CFR 2.1055 • Exhibit 6H: Pursuant 47 CFR 2.1047 had changed to Pursuant 47 CFR 2.1051 Q4) op. desc. indicates four different model versions - two are dual-band, one single- band for 450-520MHz only, and one single-band for 136-174MHz only - please explain whether both single-band versions contain identical component population as dual-band versions - if not identical hardware and component-population / BOMs etc across all four versions, if not in filing already separate test data is likely needed for different versions R4) The transmitter for all the models is the same (electrically identical) and only differences are for non-transmitter related items, regardless of frequency band configurations. Q5) concerning further two single-band versions under same FCC ID as dual-band versions, and noting also that user manual does list this FCC ID as "UHF2/VHF", what are means if any in end-use / field-use to ascertain by inspection what bands are in each device? R5) Authorized Service Personnel could determine the frequency bands programmed in the each device through CPS (Customer Programming Software) which has capability to retrieve the frequency bands available for that particular device. Please note these radios are mainly Public Safety Radios. Q6) user manual mentions "FCC type acceptance labeling" - FCC rules were changed some years ago to rename from "type acceptance" to "certification" - please revise this and/or future filings to include reflect modern FCC rule provisions R6) Modification completed. Q7) cover page of SAR mentions model tested: H97TGD9PW1AN + QA00570AA + QA00576AA op. desc. exhibit includes one more "component", i.e. "... + QA00576AA + QA00 ..." please explain whether / what are differences if any R7) The differences between these options is on single/dual bands combination as per above explanation are how these bands are configured. In term of hardware, there are no differences among these options as noted in Response 4. Exhibit 12 was amended and attached. Option: (a) H97TGD9PW1AN + QA00572AA + QA00574AA: UHF2 Only (Single band) (b) H97TGD9PW1AN + QA00570AA + QA00576AA: VHF Only (Single band) (c) H97TGD9PW1AN + QA00572AA + QA00574AA + QA00579: UHF2 [primary band]; VHF [secondary band] (Dual band enable) (d) H97TGD9PW1AN + QA00570AA + QA00576AA + QA00579: VHF [primary band]; UHF2 [secondary band] (Dual band enable) Q8) SAR pg 6 has "If P_int > P_max" - this seems confusing, i.e. said condition seems to indicate that incorrect value is being used for P_max (whereas higher power is indeed capable) - please adjust text in report to further explain as appropriate 8000 West Sunrise Blvd. Plantation. Fl 33322 Page 3 R8) Typically, the device is tuned at the nominal power. For SAR testing purposes, the radio is manually tuned to as close as possible to the max power indicated for each band. The tuning capability of the software does not allow for exact tuning due to it is limited to step-sizes, and when the power is tuned for one channel it is typically affects the adjacent channels. Therefore, the initial conducted power measurements, in some cases, are slightly above the stated maximum power but not to exceed that by more than 5%. This is the condition indicated “P_int > P_max”. Q9) SAR report table 2 has 26-75mm as distance range for PMAE4065A w/ carry- acc.; the SAR setup photos do agree with 26mm as minimum spacing, but we did not 75mm max. spacing - please explain and/or revise where appropriate R9) The following table includes separation distances for the antenna PMAE4065A and PMAT4001A when tested with each of the offered batteries (NNTN7038A or NNTN7034A) and body-worn accessories (NTN8266B or HLN6875A). TABLE R9: Separation distances between DUT antenna and phantom surface (mm) Antenna Battery Carry Accessory @ Antenna’s base @ Antenna’s tip PMAE4065A NNTN7038A NTN8266B 26 35 PMAE4065A NNTN7034A NTN8266B 26 35 PMAE4065A NNTN7038A HLN6875A 43 75 PMAE4065A NNTN7…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View with Display and Keypad. 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 2 OF 7 Exhibit 3A BACK VIEW WITH BATTERY Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 3 OF 7 Exhibit 3B FRONT VIEW WITH DISPLAY AND KEYPAD Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 4 OF 7 Exhibit 3C BACK VIEW (FCC LABELS) Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 5 OF 7 Exhibit 3D SIDE VIEW (RIGHT) Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 6 OF 7 Exhibit 3E SIDE VIEW (LEFT) Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 3 SHEET 7 OF 7 Exhibit 3F TOP VIEW

Applicant: Motorola Inc. FCC ID: AZ489FT4893 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or…

Text truncated - open the document above for the full version.