AZ489FT4906PORTABLE 2-WAY RADIO

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *6881095C98* 6881095C98-G *NNTN7223C* NNTN7223C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2011 Motorola Solutions, Inc. All rights reserved. ATTENTION! 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front of the face. Hold the radio in a vertical position with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips. Keeping the radio at a proper distance is important to ensure compliance. NOTE:RF exposures decrease with increasing distance from the antenna. • Body Worn Operation. When worn on the body, always place the radio in a Motorola-approved clip, holder, h…

Text truncated - open the document above for the full version.

APX 7000 User Guide Top Display 6875952M01-G Front_Covers.fm Page 1 Monday, January 16, 2012 4:19 PM APX_7000_TopD.book Page 2 Wedne sday, November 2, 2011 5:31 PM Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: APX 7000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. APX_7000_TopD.book Page i Wedne sday, November 2, 2011 5:31 PM Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. APX_7000_TopD.book Page ii Wedn esday, November 2, 2011 5:31 PM Declaration of Conformity English iii Additional FCC Note to Users The following FCC information applies to Bluetooth radio optionsModel Name: MNUK6000 Description: APX 7000 Bluetooth Option Board FCC ID: AZ489FT6000 IC: 109U-89FT6000 Conforms to the following regulations: FCC Part 15, Section 15.19, 15.21, and 15.105 Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the FCC, to operate this device and should not be made. See 47 CFR Part 15.21. Information to the user. The user manual or instruction manual for an intentional or unintent ional radiator shall caution the user that changes or modifications not expressly approved by the party responsib le for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operati on is subject to the following two conditions: (1 ) This device may not cause harmful interference, and (2 ) this device must accept any interferenc e received, including interference that may cause undesired operation. See 47 CFR Part. 15.19(3).This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for equipment compliance should note that the limits specified in this part will not prevent harmful interference under all circumstances.This equipment has been tested and found to comply with the limi ts for a Class B digital device, pursuant to part 15 of the FCC Rules. See Part 15.105b These limits are designed to provide reasonable protection agains t harmful interference in a residential installation. This equipmen t generates, uses and can radiate radio fr equency energy and, if not installed and used in accordance with the instructions, may c ause harmful interference to radio communications. APX_7000_TopD.book Page iii We dnesday, November 2, 2011 5:31 PM Declaration of Conformity English iv However, there is no guarantee that interference will not occu r in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experi enced radio/TV technician for help. Industry Canada (IC) Statements:This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210. Note: If the customer is purchasing the Bluetooth Option Board fo r the first time and their radios are FM approved, please send the radios back to the service center in order to keep the certification. If customer already purchased the radio with the Bluetooth Option Board as part of the tanapa and they need to replace (repair) the option board, they are able to send the radio to any Motorola FM audited location. APX_7000_TopD.book Page iv We dnesday, November 2, 2011 5:31 PM Contents English iii ContentsThis User Guide contains all the information you need to use the APX™ 7000 Series Digital Portable Radios. Declaration of Conformity . . . . . . . . . . . . . . . . .iImportant Safety Information . . . . . . . . . . . . . vii Product Safety and RF Exposure Compliance . . . . vii Software Version . . . . . . . . . . . . . . . . . . . . . . . vii Notice to Users (FCC and Industry Canada) . . . . . vii Informations importantes sur la sécurité . . .viii Sécurité du produit et respect des lignes directrices concer…

Text truncated - open the document above for the full version.

EXHIBIT 13B SHEET 1 FCC ID: AZ489FT4906 REQUEST FOR CONFIDENTIALITY January 04, 2012 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality for Transmitter with FCC ID:AZ489FT4906 Dear Sir / Madam, Motorola Solutions is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected]

FCC ID: AZ489FT4906 EXHIBITS 13C _________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. January 04, 2012 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX7000 Portable 2-Way radio was designed to operate in the frequency band 380-470 and 470-520 MHz To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola is requesting that the FCC lists the frequencies 380-470 MHz and 470- 520 MHz under FCC Rule Parts 90 on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, “as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Federa l Emission Designator Rule Part 90 380- 406* x 11K0F3E, 8K10F1D, 8K10F1E, 8K10F1W 406.1-454 x “”” 454- 456* “”” 467.7375-470 x “”” 470-512 x “”” 512-520 x “”” * Canada Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

EXHIBIT 13A SHEET 1 FCC ID: AZ489FT4906 March 28, 2012 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4906, APX7000 Gentlemen: Motorola Solutions Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Portable Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency range: 380 - 520 MHz: 1.0 – 5.7 Watts (30 – 37.6 dBm) We are requesting Certification under 90.210 and 90.210e of the Commission’s Rules to allow operation of this equipment. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. Please note that Motorola Solutions had added a Bluetooth Module, certified under FCC ID: AZ489FT6000, to this transmitter which satisfies the requirements for a Class 1 Permissive Change. We attest that the Bluetooth Module is identical to the original design and that there is no reportable performance degradation, including RF Exposure, found when adding the module to the host transmitter. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793. Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 1 OF 8 EXHIBIT 3 The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View with Display and Keypad. 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F 7. Antenna 3G Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 2 OF 8 BACK VIEW WITH BATTERY EXHIBIT 3A Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 3 OF 8 FRONT VIEW WITH DISPLAY AND KEYPAD Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 4 OF 8 EXHIBIT 3B BACK VIEW (FCC LABELS) EXHIBIT 3C Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 5 OF 8 SIDE VIEW (RIGHT) EXHIBIT 3D Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 6 OF 8 SIDE VIEW (LEFT) EXHIBIT 3E Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 7 OF 8 TOP VIEW EXHIBIT 3F Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 3 SHEET 8 OF 8 UHF1-UHF2 Antennas EXHIBIT 3G

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or Sketch X Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing.

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 1 OF 11 EXHIBIT 9 Internal Photographs The following photographs are attached. Exhibit 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D 5. Vocon board with Shields (Top). 9E 6. Vocon board without Shields (Top). 9F 7. Vocon board with Shields (Bottom). 9G 8. Vocon board without Shields (Bottom). 9H 9. Expander board with Shields (Top). 9I 10. Expander board without Shields (Top). 9J 11. Expander board with Shields (Bottom). 9K 12. Expander board without Shields (Bottom). 9L 13. Bluetooth option board with Shields (Bottom) 9M 14. Bluetooth option board without Shields (Bottom) 9N 15. Bluetooth option board with Shields (Top) 9O 16. Bluetooth option board without Shields (Top) 9P 17. Bluetooth Antenna Distance from Radio Antenna 9Q 18. RF, Vocon and Expander board with chassis and housing (front side) 9R 19. RF, Vocon and Expander board with chassis and housing (back side) 9S Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 2 OF 11 EXHIBIT 9A RF board with Shields (Top) EXHIBIT 9B Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 3 OF 11 RF board without Shields (Top) EXHIBIT 9C RF board with Shields (Bottom) EXHIBIT 9D Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 4 OF 11 RF board without Shields (Bottom) EXHIBIT 9E Vocon board with Shields (Top) EXHIBIT 9F Vocon board without Shields (Top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 5 OF 11 EXHIBIT 9G Vocon board with shields board (Bottom) EXHIBIT 9H Vocon board without shields board (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 6 OF 11 EXHIBIT 9I Expander board with shieldMs board (top) EXHIBIT 9J Expander board without shields board (top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 7 OF 11 EXHIBIT 9K Expander board with shields board (Bottom) EXHIBIT 9L Expander board without shields board (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 8 OF 11 EXHIBIT 9M Bluetooth option board with Shields (Top) EXHIBIT 9N Bluetooth option board without Shields (Top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 9 OF 11 EXHIBIT 9O Bluetooth option board with Shields (Bottom) EXHIBIT 9P Bluetooth option board without Shields (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 10 OF 11 EXHIBIT 9Q Bluetooth Antenna Distance from Radio Antenna Bluetooth Antenna Radio Antenna Applicant: Motorola Solutions Inc. FCC ID: AZ489FT4906 EXHIBIT 9 SHEET 11 OF 11 EXHIBIT 9R RF, Vocon and Expander with chassis and housing (front side) EXHIBIT 9S RF, Vocon and Expander with chassis and housing (back side)

FCC ID: AZ489FT4906 Bluetooth Antenna Distance from Radio Antenna (54.4114mm) Bluetooth Antenna Launch Radio Antenna Launch

SR 9408 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.01 Page 1 of 162 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 3 Motorola Solutions Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322. Date of Report: 3/22/2012 Report Revision: B Report ID: SR9408 APX7000 U1/U2 BT Rev B 120322 Responsible Engineer: Deanna Zakharia ( Lab Senior Resource Manager /Laboratory Director ) Kim Uong (Principal Staff Engineer) Report Author: Kim Uong (Principal Staff Engineer) Date/s Tested: 5/28/2011-6/17/2011, 10/19/2011 – 12/15/2011 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: G&PS Date submitted for test: 04/18/2011 DUT Description: 380-470MHz 1-5W, 470-520MHz 1-5W, 6.25kHz/12.5kHz/25kHz, Basic Top Display Model-1, W/GPS & with Bluetooth. Capable of digital and analog FM transmission. Also capable of TDMA transmission. Test TX mode(s): CW (PTT); CW (BlueTooth) Max. Power output: 5.7W (UHF R1) & 5.6W (UHF R2), 12mW (Bluetooth) Nominal Power: 5.0W (UHF R1) & 5.0W (UHF R2), 12mW (Bluetooth) Tx Frequency Bands: 380-406 MHz (UHF R1) & 406.1-470 MHz (UHF R1) & 470-520 MHz (UHF R2), 2.402-2.480 GHz (Bluetooth) Signaling type: FM, TDMA, FHSS (Bluetooth) Model(s) Tested: H97TGD9PW1AN (NUE3622) Model(s) Certified: H97TGD9PW1AN (NUE3622) Serial Number(s): Q0SOM063 and Q0SOM064 Classification: Occupational/Controlled FCC ID: AZ489FT4906; Rule part 90 (406.1 – 512 MHz); Rule part 15 (2402 – 2480 MHz) Results outside FCC bands are not applicable for FCC compliance demonstration. * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 3/22/2012 Certification Date: Certification No.: SR 9408 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.01 Page 2 of 162 Part 1 of 3 1.0 Introduction ................................................................................................................................. 5 2.0 Abbreviations / Definitions ......................................................................................................... 5 3.0 Referenced Standards and Guidelines ........................................................................................ 5 4.0 SAR Limits ................................................................................................................................. 6 5.0 SAR Result Scaling Methodology .............................................................................................. 7 6.0 Description of Device Under Test (DUT) .................................................................................. 7 7.0 Optional Accessories and Test Criteria ...................................................................................... 8 7.1 Antennas ......................................................................................................................... 8 7.2 Batteries .......................................................................................................................... 9 7.3 Body worn Accessories ................................................................................................ 10 7.4 Audio Accessories ........................................................................................................ 11 8.0 Description of Test System ....................................................................................................... 13 8.1 Descriptions of Robotics/Probes/Readout Electronics ................................................. 13 8.2 Description of Phantom(s) ............................................................................................ 13 8.2.1 Dual Flat Phantom ......................................................................................... 13 8.2.2 SAM Phantom ................................................................................................ 13 8.2.3 Elliptical Phantom ......................................................................................... 14 8.3 Description of Simulated Tissue ................................................................................... 14 9.0 Additional Test Equipment ....................................................................................................... 15 10.0 SAR Measurement System Verification ................................................................................... 16 10.1 Equivalent Tissue Test Results ..................................................................................... 16 10.2 System Check Test Results ........................................................................................... 21 11.0 Environmental Test Conditions .....................................…

Text truncated - open the document above for the full version.

SR 9408 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.01 Page 1 of 60 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 3 Motorola Solutions Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322. Date of Report: 3/22/2012 Report Revision: B Report ID: SR9408 APX7000 U1/U2 BT Rev B 120322 Responsible Engineer: Deanna Zakharia ( Lab Senior Resource Manager /Laboratory Director ) Kim Uong (Principal Staff Engineer) Report Author: Kim Uong (Principal Staff Engineer) Date/s Tested: 5/28/2011-6/17/2011, 10/19/2011 – 12/15/2011 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: G&PS Date submitted for test: 04/18/2011 DUT Description: 380-470MHz 1-5W, 470-520MHz 1-5W, 6.25kHz/12.5kHz/25kHz, Basic Top Display Model-1, W/GPS & with Bluetooth. Capable of digital and analog FM transmission. Also capable of TDMA transmission. Test TX mode(s): CW (PTT); CW (BlueTooth) Max. Power output: 5.7W (UHF R1) & 5.6W (UHF R2), 12 mW (Bluetooth) Nominal Power: 5.0W (UHF R1) & 5.0W (UHF R2), 12 mW (Bluetooth) Tx Frequency Bands: 380-406 MHz (UHF R1) & 406.1-470 MHz (UHF R1) & 470-520 MHz (UHF R2), 2.402-2.480 GHz (Bluetooth) Signaling type: FM, TDMA, FHSS (Bluetooth) Model(s) Tested: H97TGD9PW1AN (NUE3622) Model(s) Certified: H97TGD9PW1AN (NUE3622) Serial Number(s): Q0SOM063 and Q0SOM064 Classification: Occupational/Controlled FCC ID: AZ489FT4906; Rule part 90 (406.1 – 512 MHz); Rule part 15 (2402 – 2480 MHz) Results outside FCC bands are not applicable for FCC compliance demonstration. * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 3/22/2012 Certification Date: Certification No.: SR 9408 Motorol…

Text truncated - open the document above for the full version.