AZ489FT4926Portable 2-way Radio

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *NNTN7223G* NNTN7223G MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2013 Motorola Solutions, Inc. All rights reserved. ATTENTION! *6881095C98* 6881095C98-K 6881095C98-K_SafetyP.book Page 1 Tuesday, September 3, 2013 3:56 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C98-K_SafetyP.book Page 2 Tuesday, September 3, 2013 3:56 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C98-K_SafetyP.book Page 3 Tuesday, September 3, 2013 3:56 PM 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 6881095C98-K_SafetyP.book Page 4 Tuesday, September 3, 2013 3:56 PM 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. The PTT button may reside on the radio itself or may be hosted on approved wired or wireless (for example, a Bluetooth enabled remote Push-to-Talk button) accessories. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front…

Text truncated - open the document above for the full version.

1 *6864110W15* 6864110W15-D Models CLS1110 and CLS1410 SERIES TWO-WAY RADIO User's Guide 2 Contents i Introduction ...................................... 1FCC Licensing Information ............. 3RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use ........................ 5 Radio Controls ............................... 18Getting Started ............................... 19 Installing the Swivel Belt Holster .. 19Installing the Batteries .................. 20Charging the Battery .................... 21Turning Your Radio On and Off .... 24Adjusting the Volume ................... 25Reading the Display ..................... 25 Talking and Receiving ................... 26 Basic Radio Operation ................. 26Signal Strength and Channel Busy Indicators .......................... 26 Talk Range ................................... 27Handsfree Use (VOX) (CLS1410 only) ......................... 27 Locking the Keypad ...................... 28Monitoring a Channel .................... 29Scanning (CLS1410 Only) ............ 29 Programming Mode ........................ 31 Factory Default Settings ............... 32Entering Programming Mode ........ 33 Cloning Radio Settings .................. 37Advanced Features ........................ 38Troubleshooting ............................ 40Use and Care .................................. 43Frequencies and Bandwidths ....... 44Spirit GT Series Programming ...... 50Warranty .......................................... 51 Contents ii Notes Introduction 1 Introduction Thank you for purchasing a Motorola _ Series Radio. Your radio is a product of Motorola’s 85 plus years of experience as a world leader in designing and manufacturing communications equipment. The _ Series radios provide cost- effective communications for businesses such as retail stores, restaurants, hotels, and schools. Motorola professional two- way radios are the perfect communications solution for all of today’s fast-paced industries.Please read this guide carefully so you know how to properly operate the radio before use. Package Contents • _ Series Radio • Swivel Belt Holster• Lithium Ion Battery • Drop-In Charger with Transformer• User's Guide Introduction 2 For product-related questions, please call: 1-800-448-6686 in the USA 1-888-390-6456 TTY (Text Telephone) On the Web: www.motorolasolutions.com/CLS ATTENTION Before using this product, read the RF energy awareness information and operating instructions in the Safety and General Info rmation section of this guide to ensure compliance with RF energy exposure limits. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.© 2003 – 2010, 2014 Motorola Solutions, Inc.All rights reserved FCC Licensing Information 3 FCC Licensing Information Interference InformationThis device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference._ Series™ Business two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159.To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed or have questions, use the following contact information.Before filling out your application, you must decide which frequency(ies) you can operate on. See “Frequencies and Code Charts”. For questions on determining the radio frequency, call Motorola Product Services at: 1-800-448-6686 Faxed contact the Fax-On- Demand system at: Mailed call the FCC forms hotline at: Questions regarding FCC license contact the FCC at: 1-202-418-0177 1-800-418-FORM 1-800-418-3676 1-888-CALL-FCC1-888-225-5322Or: http://www.fcc.gov FCC Licensing Information 4 Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comp ly with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semi conductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use 5 RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a di stance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one fo rm of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF ener gy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, ca n damage tissues and genetic material. …

Text truncated - open the document above for the full version.

FCC ID: AZ489FT4926 Motorola Solutions Inc. Exhibit 13c 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Date: June 29, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: AZ489FT4926 Dear Sir or Madam: This transmitter was design to operate in the following frequency ranges: To aid equipment authorization in other countries that accept the United States FCC Grant for Certification, Motorola (Motorola Solutions Inc) is requesting that the FCC list the above frequency/frequencies under FCC Rule Parts 90 on the Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Emission Designator 450-454 x 11K0F3E 454-456* 456-460 x 460-462.5375 x 462.5375-462.7375* 462.7375-467.5375 x 467.5375-467.7375* 467.7375-470 x *Canada Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ489FT4926 Motorola Solutions Inc. Exhibit 13b 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 CONFIDENTIALITY REQUESTED Date: June 29, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request Regarding Application for Transmitter with FCC ID: AZ489FT4926 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) is requesting for the following Exhibits be held as Permanently Confidential, and not be made routinely available for public inspection: Exhibit 4 Circuit Descriptions/Block diagrams Exhibit 5 Schematic Exhibit 10 Parts List and Tune Up Procedures Exhibit 12 Transmitter Description Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Sections 0.457(d), 0.459 and 552(b)(4) of the Freedom of Information Act. Please mark these Exhibits as “Confidential.” Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ489FT4926 Motorola Solutions Inc. Exhibit 13a 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Date: June 29, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT4926 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) herein submits application for certification of the subject transmitter. This transmitter is intended for use in a Portable Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency ranges: Frequency Rated Power FCC Rule Parts 450-470 MHz 1.0 W 90 We are requesting certification under Part(s) of the Commission’s Rules listed above to allow operation of this equipment. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 6 EXHIBIT 3: EXTERNAL PHOTOGRAPHS Figure 3-1 CLS1410 Front View Figure 3-2 CLS1410 Back View (FCC MODEL) (FCC MODEL) FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 6 Figure 3-3 CLS1413 Front View Figure 3-4 CLS1413 Back View (IC MODEL) (IC MODEL) FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 6 Figure 3-5 Top View (Both Models) Figure 3-6 Bottom View (Both Models) FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 6 Figure 3-7 Side View Figure 3-8 Side View Figure 3-9 Side View Power/Volume Knob & Accessory Jack Accessory Jack Call Button with Dust Cover (Both Models) FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 5 of 6 (Both Models) (Both Models) Figure 3-10 CLS1410 Battery Compartment & Labels (FCC Model) FCC ID: AZ489FT4926/ IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 6 of 6 Figure 3-11 CLS1413 Battery Compartment & Labels (IC Model)

FCC ID: AZ489FT4926/ IC:109U-89FT4926 EXHIBIT 1: IDENTIFICATION LABEL LOCATION X See the attached Photograph, and Exhibit 3-8 for the location of the Label on the device. Back of Radio Back of Radio under Belt Clip Please note that Motorola complies with FCC Rule Part 2.907(b) that the label is permanently affixed and is readily visible to the purchaser at the time of purchase. TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/ inch. The label is laser etched into the Urethane paint, exposing the Nickel plating on the Zamak casting substrate. Since no adhesive is required, the label is permanent and tamper-proof. (** - NOTE- The label attached below is a paper polyester film laminate, as described above. This is just for sample purposes, as the actual label is laser etched into the casting) MARKINGS (TEXT) See Photograph, Exhibit 1. US Model CU1410BKV4BA Canada Model CU1413BKV4BA S/N: 134TQA0327 Made in Malaysia MAR, 5, 2015 Tnp: HCUE1081F FCC ID: AZ489FT4926 Mdl: CU1410BKV4BA S/N: 134TQA0227 Made in Malaysia MAR, 5, 2015 Tnp: HCUE1082F IC: 109U-89FT4926 Mdl: CU1413BKV4BA FCC ID: AZ489FT4926/ IC:109U-89FT4926 Exhibit 1A GENERAL INFORMATION I. Production Plans—Pursuant 2.907(b). Quantity production is planned. II. Application References Reference is made to the following Motorola “Application References” 1. Portable Products and their application. 2. Portable Products Transmitter Modulations Methods. III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ Rules.

FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 8 EXHIBIT 9: INTERNAL PHOTOGRAPHS Figure 9-1 Internal Top Side Photo. FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 8 Figure 9-2 Internal Bottom Side Photo with Shields. FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 8 Figure 9-3 Internal Bottom Side Photo without Shields. FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 8 Figure 9-4 Internal Photo Antenna Ring FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 5 of 8 Figure 9-5 Front Housing FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 6 of 8 Figure 9-6 Back Housing FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 7 of 8 Figure 9-7 Back Housing W/Antenna FCC ID: AZ489FT4926/IC:109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 8 of 8 Figure 9-8 Board Assembly

FCC ID: AZ489FT4926/ IC: 109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 9 EXHIBIT 7: MEASUREMENT PROCEDURES – Pursuant 47 CFR 2.947 Except where otherwise stated, all measurements are made following the Electronic Industries Association (EIA) Minimum Standard for Portable/Personal Land Mobile Communications FM or PM Equipment 25-1000 MHz-(TIA/EIA-603-D) and RSS-119 Issue 11. This exhibit presents a brief summary of how the measurements were made, the required limits, and the test equipment used. The following procedures are presented with this application. 7.1 RF Power Output 7.2 Modulation Characteristics A. Modulation Limiting B. Audio Response 7.3 Occupied Bandwidth & Emission Mask A. Occupied Bandwidth B. Emission Mask 7.4 Radiated Spurious Emissions 7.5 Frequency Stability A. Vs. Temperature B. Vs. Supply Voltage 7.6 Transient Frequency Behavior 7.7 Measurement Equipment List & Lab Information 7.8 List of FCC and IC references EXHIBIT 7 FCC ID: AZ489FT4926/ IC: 109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 9 7.1 RF Output Power -- Pursuant 47 CFR 2.1046 & 90.205 ( Test Conducted at Motorola EME accredited lab in May 2015) The RF power output is measured with the value of voltage and current as required by 2.1046. A 50 ohm RF attenuator of proper power rating was used as a load for making these measurements. For Transmitter having output impedance other than 50 ohm, a suitable matching network is placed between the transmitter and the load. 7.2 Modulation Characteristics -- Pursuant 47 CFR 2.1047 & 90.207 (Measured in June 2015 @ MSI Plantation Eng. Lab) Procedure: A. Modulation Limiting: a. Configure the EUT as shown in figure 1, adjust the audio input for 60% of rated system deviation at 1 KHz audio input using this level as a reference (0dB) and vary the input level from rated to +20dB. Record the frequency deviation obtained as a function of the input level. b. 2 Sweep audio input frequency from 100 HZ to 5KHz for all three audio levels and record the deviation. Figure 1. Modulation limiting setup Minimum Standard The transmitter modulation must not exceed maximum system deviation at any audio frequency input or reasonable change in input level. EXHIBIT 7 FCC ID: AZ489FT4926/ IC: 109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 9 B. Audio Response: a. Configure the EUT as shown in figure 2, adjust the audio input for 20% of rated system deviation at 1 KHz audio frequency input using this level as a reference (0dB). b. Vary the Audio frequency from 100 Hz to 3 KHz and record the frequency deviation. 4 Audio Frequency Response =20log10 (Deviation of test frequency/Deviation of 1 KHz reference). Figure 2. Audio Response setup Minimum Standard The audio frequency response shall not vary more than +1 or -3 dB from 300 to 3000 Hz as referenced to 1000 Hz level (with the exception of a permissible 6 dB/octave roll off from 2500 to 3000 Hz) 7.3 Occupied Bandwidth and Emission Mask – Pursuant 47 CFR 2.1049 & 90.209, 90.210 (Measured in June 2015 @ MSI Plantation Eng. Lab) A. Occupied Bandwidth Data on occupied bandwidth is presented in the form of a spectrum analyzer photograph, which illustrates the transmitter sidebands. A photograph is taken of the spectrum with the carrier modulated with a 2500 Hz tone at a level 16 dB greater than that required to produce 50 percent modulation As shown in figure 2, the EUT was connected to the audio signal generator and the spectrum analyzer via the main RF connector, and through an appropriate attenuator. The EUT was controlled to transmit its maximum power. Then the bandwidth of 99% power can be measured by the spectrum analyzer. FCC Limits - According to FCC Part 90.209, equipment with 12.5KHz channel bandwidth will be authorized 11.25 KHz bandwidth. Equipment with 25 KHz channel bandwidth will be authorized 20KHz bandwidth. EXHIBIT 7 FCC ID: AZ489FT4926/ IC: 109U-89FT4926 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 9 B. Emission Mask A plot is generated of the unmodulated carrier, for reference, to which is superimposed the sideband display generated by modulating the carrier with a 2500 Hz tone at a level 16 dB greater than that required to produce 50 percent modulation. If tone or digital coded squelch is indicated, plots are generated using both the 2500 Hz tone and the indicated squelch signal to modulate the transmitter. During these measurements, the instantaneous Deviation Control is set for a maximum of +2.5 kHz. As shown in figure 2, the EUT was connected to the audio signal generator and the spectrum analyzer via the main RF connector, and through an appropriate attenuator. The EUT was controlled to transmit its maximum power. Then the bandwidth of 99% power can be measured by the spectrum analyzer. FCC Limits - Per FCC 47 CFR, 90.210: Emission Mask D, 12.5 kHz channel bandwidth equipment: For transmitters designed to operate with a 12.5 kHz channel bandwidth, any emission must be attenuated below the power (P) of the highest emission contained within the authorized bandwidth as follows: (1) On any frequency from the center of the authorized bandwidth f0 to 5.625 kHz removed from f0: Zero dB. (2) On any frequency removed from the centre of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 5.625 kHz but no more than 12.5 kHz: At least 7.27(fd -2.88 kHz) dB. (3) On any frequency removed from the center of the authorized bandwidth by a displacement frequency (fd in kHz) of more than 12.5 kHz: At least 50 + 10 log (P) dB or 70 dB, whichever is the lesser attenuation. Figure 2. Occupied Bandwidth and Emission Mask Setup EXHIBIT 7 7.4 Transmit Radiated Spurious Emissions -- Pursuant 47 CFR 2.1051, 2.1053, 90.210. (Test Conducted at Timco Engineering Inc in June 2015) Please see attached TIMCO Radiated Spurious Emissions test report as part of the package for full test method details. FCC I…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 1 of 11 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Motorola Solutions Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: 07/02/2015 Report Revision: B Responsible Engineer: Jessica Zada (EME Engineer) Report Author: Jessica Zada (EME Engineer) Date/s Tested: 5/20/2015-5/21/2015 Manufacturer/Location: Motorola Solutions Inc., Penang Sector/Group/Div.: Business Light Date submitted for test: 05/14/2015 DUT Description: CLS1410 Black; 450-470 MHz at 1.0W Test TX mode(s): CW (PTT) Max. Power output: 1.0 W for 450-470 MHz Nominal Power: 1.0 W for 450-470 MHz Tx Frequency Bands: 450-470 MHz Signaling type: FM Model(s) Tested: HCUE1081F (CU1410BKV4BA) Model(s) Certified: HCUE1081F (CU1410BKV4BA), HCUE1082F (CU1413BKV4BA) Serial Number(s): 134TQA0248, 134TQA0327 Classification: Occupational/Controlled FCC ID: AZ489FT4926; 450-470 MHz IC: 109U-89FT4926 The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of OET Bulletin 65. The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 4.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 7/2/2015 Certification Date: 6/2/2015 Certification No.: L1150534 FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 2 of 11 Appendix D System Verification Check Scans FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 3 of 11 FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 4 of 11 FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 5 of 11 Appendix E DUT Scans FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 6 of 11 Assessments at the Body - Table 17 FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 7 of 11 Assessments at the Face - Table 19 FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.13 Page 8 of 11 APPENDIX F Shortened Scan of Highest SAR configuration FCC ID: AZ489FT4926 / IC: 109U-89FT4926 Report ID: P2969-EM…

Text truncated - open the document above for the full version.