AZ489FT5798Hand Held Portable Transmitter

1 English CONTENTS Computer Software Copyrights . . . . . . . . . . 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety and General Information . . . . . . . . . 5 RF Operational Characteristics . . . . . . . 5Exposure To Radio Frequency Energy . 5 Portable Radio Operation and EME Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Antenna Care . . . . . . . . . . . . . . . . . . . . . 6Two-Way Radio Operation. . . . . . . . . . . 6Body-Worn Operation . . . . . . . . . . . . . . 6Data Operation. . . . . . . . . . . . . . . . . . . . 6Approved Accessories . . . . . . . . . . . . . . 7 Electromagnetic Interference/Compatibility . . . . . . . . . . . . . . . . . . . . . . . . 7Safety and General . . . . . . . . . . . . . . . . . . . 8Operational Warnings . . . . . . . . . . . . . . . . . 8Operational Cautions . . . . . . . . . . . . . . . . . 9Intrinsically Safe Radio Information. . . . . . 10 FMRC Approved Equipment . . . . . . . . 10Repair of FMRC Approved Products . . 11 Radio Overview . . . . . . . . . . . . . . . . . . . . 15 Parts of the Radio . . . . . . . . . . . . . . . . . . . 15 PRO7550™ and PRO7650™ Models . 15 On/Off/Volume Knob . . . . . . . . . . . . . . 16Mode Selector Knob . . . . . . . . . . . . . . 16LED Indicator. . . . . . . . . . . . . . . . . . . . 16Push-to-Talk (PTT) Button . . . . . . . . . 16Microphone . . . . . . . . . . . . . . . . . . . . . 16Keypad Keys . . . . . . . . . . . . . . . . . . . . 16Menu Keys . . . . . . . . . . . . . . . . . . . . . 18Selecting a Feature . . . . . . . . . . . . . . . 18Menu Display. . . . . . . . . . . . . . . . . . . . 19LCD Screen and Icons . . . . . . . . . . . . 19Alert Tone Indications . . . . . . . . . . . . . 20Programmable Buttons . . . . . . . . . . . . 22 Trunked Radio Systems . . . . . . . . . . . . . . 24 Getting Started . . . . . . . . . . . . . . . . . . . . 25 Battery Information . . . . . . . . . . . . . . . . . . 25 Charging the Battery . . . . . . . . . . . . . . 25Battery Charge Status . . . . . . . . . . . . . 26Attaching the Battery . . . . . . . . . . . . . . 27Removing the Battery . . . . . . . . . . . . . 27 Accessory Information . . . . . . . . . . . . . . . 28 Removing the Antenna . . . . . . . . . . . . 28Attaching the Belt Clip . . . . . . . . . . . . . 29Removing the Belt Clip . . . . . . . . . . . . 29Attaching the Side Connector Cover . . 30Turning The Radio On or Off . . . . . . . . 30 Receiving a Trunked Call . . . . . . . . . . . . . 30 CONTENTS 2 English CONTENTS Radio Self Test . . . . . . . . . . . . . . . . . . . . . 31 Radio Calls (Trunked Operation Only) . 33 Selecting a Zone and Mode . . . . . . . . . . . 33 Selecting a Zone . . . . . . . . . . . . . . . . . 33Selecting a Mode. . . . . . . . . . . . . . . . . 34 Receiving a Call . . . . . . . . . . . . . . . . . . . . 34Making a Call . . . . . . . . . . . . . . . . . . . . . . 34 Conventional Modes . . . . . . . . . . . . . . 34Trunked Modes . . . . . . . . . . . . . . . . . . 35Low-Battery Alert . . . . . . . . . . . . . . . . . 35Coded Squelch Operation . . . . . . . . . . 35Variable RF Power Level (SelectedModels Only) . . . . . . . . . . . . . . . . . . . . 35 Failsoft Operation (Trunked SystemsOnly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Muting the Keypad Tones. . . . . . . . . . . . . 36 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Scan Operation. . . . . . . . . . . . . . . . . . . . . 37 Turning Scan On or Off with theKeypad) . . . . . . . . . . . . . . . . . . . . . . . . 37Deleting Nuisance Modes . . . . . . . . . . 38Viewing a Scan List . . . . . . . . . . . . . . . 38Programming a Scan List . . . . . . . . . . 39 Trunked Features . . . . . . . . . . . . . . . . . . 41 Viewing Your Radio’s ID Number. . . . . . . 41Enhanced Private Call Operation. . . . . . . 41 Answering a Private Call . . . . . . . . . . . 42Making a Private Call . . . . . . . . . . . . . 43 Call Alert™ Operation . . . . . . . . . . . . . . . 46 Answering a Call Alert™ Page with a Group Call . . . . . . . . . . . . . . . . . . . . 46Making a Call Alert™ . . . . . . . . . . . . . 46Initiating a Call Alert . . . . . . . . . . . . . . 46Sending the Call Alert . . . . . . . . . . . . . 48 Programming the Radio’s Lists . . . . . . . . 49 Programming the Telephone ListNumbers . . . . . . . . . . . . . . . . . . . . . . . 49Programming the Call List. . . . . . . . . . 50 Trunked Telephone Operation . . . . . . . . . 52 Answering a Telephone Call . . . . . . . . 52Making a Telephone Call . . . . . . . . . . 53 Automatic Multiple Site Selection (AMSS) (PRO7650 Only). . . . . . . . . . . . . . . . . . . . 56 Forcing a Site Change . . . . . . . . . . . . 56Locking and Unlocking a Site . . . . . . . 56 Conventional Call. . . . . . . . . . . . . . . . . . 57 Selecting a Conventional Channel . . . . . . 57Sending a Conventional Call . . . . . . . . . . 57Repeater or Talkaround Mode . . . . . . . . . 57 3 English CONTENTS Smart PTT. . . . . . . . . . . . . . . . . . . . . . . . . 58 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 59 Limited Warranty . . . . . . . . . . . . . . . . . . . . 59 Accessories . . . . . . . . . . . . . . . . . . . . . . . 65 Carry Cases . . . . . . . . . . . . . . . . . . . . . . . 65Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . 65Headsets . . . . . . . . . . . . . . . . . . . . . . . . . . 65Remote Speaker Microphones . . . . . . . . . 66Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . 66Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 66Miscellaneous . . . . . . . . . . . . . . . . . . . . . . 66Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 67 COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and oth-er countries preserve for Motorola certain ex-clusive righ…

Text truncated - open the document above for the full version.

Guía del usario Manual do usuário User Guide contacto control Radios Profesionales Tan Dedicado Como Lo Es Usted C A, Motorola, Radios Profesionales, Serie PRO, PRO7550, PRO7650, Tan Dedicado Como Lo Es Usted, Privacy Plus, y Call Alert son marcas de Motorola, Inc. © 2000 Motorola, Inc. Todos los derechos reservados. Impreso en los EE.UU. A, Motorola, Rádios Profissionais, Série PRO, PRO7550, PRO7650, Tão Dedicado Quanto É Você, Privacy Plus, e Call Alert são marcas de Motorola, Inc. © 2000 Motorola, Inc. Todos os direitos reservados. Impresso nos EUA. A, Motorola, Professional Radio, PRO Series, PRO7550, PRO7650, As Dedicated As You Are, Privacy Plus, and Call Alert are trademarks of Motorola, Inc. © 2000 Motorola, Inc. All rights reserved. Printed in U.S.A. *6881093C86* 68P81093C86-A contacto control PRO7550 PRO7550™ and PRO7650™ Radio Portátil Rádio Portátil Portable Radio 1 English CONTENTS Computer Software Copyrights . . . . . . . . . . 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety and General Information . . . . . . . . . 5 RF Operational Characteristics . . . . . . . 5Exposure To Radio Frequency Energy . 5 Portable Radio Operation and EME Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Antenna Care . . . . . . . . . . . . . . . . . . . . . 6Two-Way Radio Operation. . . . . . . . . . . 6Body-Worn Operation . . . . . . . . . . . . . . 6Approved Accessories . . . . . . . . . . . . . . 7 Electromagnetic Interference/Compatibility . . . . . . . . . . . . . . . . . . . . . . . . 7Safety and General . . . . . . . . . . . . . . . . . . . 8Operational Warnings . . . . . . . . . . . . . . . . . 8Operational Cautions . . . . . . . . . . . . . . . . . 9Intrinsically Safe Radio Information. . . . . . 10 FMRC Approved Equipment . . . . . . . . 10Repair of FMRC Approved Products . . 11 Radio Overview . . . . . . . . . . . . . . . . . . . . 15 Parts of the Radio . . . . . . . . . . . . . . . . . . . 15 PRO7550™ and PRO7650™ Models . 15On/Off/Volume Knob . . . . . . . . . . . . . . 16 Mode Selector Knob . . . . . . . . . . . . . . 16LED Indicator. . . . . . . . . . . . . . . . . . . . 16Push-to-Talk (PTT) Button . . . . . . . . . 16Microphone . . . . . . . . . . . . . . . . . . . . . 16Keypad Keys . . . . . . . . . . . . . . . . . . . . 16Menu Keys . . . . . . . . . . . . . . . . . . . . . 18Selecting a Feature . . . . . . . . . . . . . . . 18Menu Display. . . . . . . . . . . . . . . . . . . . 19LCD Screen and Icons . . . . . . . . . . . . 19Alert Tone Indications . . . . . . . . . . . . . 20Programmable Buttons . . . . . . . . . . . . 22 Trunked Radio Systems . . . . . . . . . . . . . . 24 Getting Started . . . . . . . . . . . . . . . . . . . . 25 Battery Information . . . . . . . . . . . . . . . . . . 25 Charging the Battery . . . . . . . . . . . . . . 25Battery Charge Status . . . . . . . . . . . . . 26Attaching the Battery . . . . . . . . . . . . . . 27Removing the Battery . . . . . . . . . . . . . 27 Accessory Information . . . . . . . . . . . . . . . 28 Removing the Antenna . . . . . . . . . . . . 28Attaching the Belt Clip . . . . . . . . . . . . . 29Removing the Belt Clip . . . . . . . . . . . . 29Attaching the Side Connector Cover . . 30Turning The Radio On or Off . . . . . . . . 30 Receiving a Trunked Call . . . . . . . . . . . . . 30Radio Self Test . . . . . . . . . . . . . . . . . . . . . 31 CONTENTS 2 English CONTENTS Radio Calls (Trunked Operation Only) . 33 Selecting a Zone and Mode . . . . . . . . . . . 33 Selecting a Zone . . . . . . . . . . . . . . . . . 33Selecting a Mode. . . . . . . . . . . . . . . . . 34 Receiving a Call . . . . . . . . . . . . . . . . . . . . 34Making a Call . . . . . . . . . . . . . . . . . . . . . . 34 Conventional Modes . . . . . . . . . . . . . . 34Trunked Modes . . . . . . . . . . . . . . . . . . 35Low-Battery Alert . . . . . . . . . . . . . . . . . 35Coded Squelch Operation . . . . . . . . . . 35Variable RF Power Level (SelectedModels Only) . . . . . . . . . . . . . . . . . . . . 35 Failsoft Operation (Trunked SystemsOnly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Muting the Keypad Tones. . . . . . . . . . . . . 36 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Scan Operation. . . . . . . . . . . . . . . . . . . . . 37 Turning Scan On or Off with theKeypad) . . . . . . . . . . . . . . . . . . . . . . . . 37Deleting Nuisance Modes . . . . . . . . . . 38Viewing a Scan List . . . . . . . . . . . . . . . 38Programming a Scan List . . . . . . . . . . 39 Trunked Features . . . . . . . . . . . . . . . . . . 41 Viewing Your Radio’s ID Number. . . . . . . 41Enhanced Private Call Operation. . . . . . . 41 Answering a Private Call . . . . . . . . . . . 42Making a Private Call . . . . . . . . . . . . . 43 Call Alert™ Operation . . . . . . . . . . . . . . . 46 Answering a Call Alert™ Page with a Group Call . . . . . . . . . . . . . . . . . . . . 46Making a Call Alert™ . . . . . . . . . . . . . 46Initiating a Call Alert . . . . . . . . . . . . . . 46Sending the Call Alert . . . . . . . . . . . . . 48 Programming the Radio’s Lists . . . . . . . . 49 Programming the Telephone ListNumbers . . . . . . . . . . . . . . . . . . . . . . . 49Programming the Call List. . . . . . . . . . 50 Trunked Telephone Operation . . . . . . . . . 52 Answering a Telephone Call . . . . . . . . 52Making a Telephone Call . . . . . . . . . . 53 Automatic Multiple Site Selection (AMSS) (PRO7650 Only). . . . . . . . . . . . . . . . . . . . 56 Forcing a Site Change . . . . . . . . . . . . 56Locking and Unlocking a Site . . . . . . . 56 Conventional Call. . . . . . . . . . . . . . . . . . 57 Selecting a Conventional Channel . . . . . . 57Sending a Conventional Call . . . . . . . . . . 57Repeater or Talkaround Mode . . . . . . . . . 57Smart PTT . . . . . . . . . . . . . . . . . . . . . . . . 58 3 English CONTENTS Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 59 Limited Warranty . . . . . . . . . . . . .…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 2 STATEMENT OF CERTIFICATION The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: I have received a B.Sc. degree in Electrical Engineering from the University of Toronto, Toronto, Canada. I have more than 10 years of Product Development experience in the field of two-way radio communication. NAME: Jim Kenning SIGNATURE: Jim Kenning DATE: 29th. September, 2000 POSITION: Engineering Group Leader I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME: Matt Gimpelj SIGNATURE: Matt Gimpelj DATE: 29th. September, 2000 POSITION: Engineering Manager

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 11 RF EXPOSURE INFORMATION In accordance with 47 CFR 2.1093 (c), this transmitter has been subject to routine environmental evaluation for RF exposure and found to be compliant with the limits specified 47 CFR 2.1093 (d).

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 4 EXHIBIT 4 CIRCUIT DESCRIPTION 4.1. Carrier Frequency Generation and Stabilization A 16.8 MHz reference frequency is generated and stability is maintained with +/- 1.5 ppm temperature stability from -30 to +60 degrees Celsius by a purchased, self contained temperature compensated crystal oscillator (TCXO) reference oscillator. The reference frequency is multiplied up to the carrier frequency by a custom fractional-N synthesizer IC and voltage controlled oscillator (VCO) forming a phase-locked loop. 4.2. Digital Modulation Techniques The transmitter is capable of the following types of modulation: i) Voice 300Hz to 3kHz ii) Modulation of PL (Private Line) - Direct FM tone modulation of 67 Hz to 250.3 Hz at 15% of full system deviation. iii) Modulation of DPL (Digital Private Line) - Direct FM modulation at 134 BPS at 15% of full system deviation. iv) Modulation of DTMF tones at nominally 60% of full system deviation. v) Trunking High Speed Data. Direct FM of PL or DPL is generated by a 6-bit D/A converter contained within U404. The frequency-determining clock signal is generated by the radio microcomputer. The modulation signal is processed through a five pole switched capacitor filter. The output of the filter is input to the electronic attenuator circuit. The microcomputer adjusts the attenuator to compensate for modulation sensitivity variations of the synthesizer & channel bandwidth ensuring 15% of full system deviation for PL and DPL. DTMF tones are generated by the audio processing IC, U404 . The tones are routed and processed in the same manner as the voice signals 4.3. Modulation Limiting and Post Limiter Filter Modulation limiting is accomplished within the custom IC, U404. The limiting action itself occurs at the rails (i.e., 3.3V and ground). Using an opamp with feedback, very hard limiting is obtained. The limited modulation signal is then input through a low-pass splatter filter then to an electronic attenuator within U404 in order to adjust for variations in modulation sensitivities of the frequency synthesizer. The electronic attenuator is controlled by the radio’s micro-processor, U409. To keep the deviation constant over the RF frequency range & channel bandwidth, the microcomputer adds the proper correction factor to the attenuator. 4.4. Means for Output Power Limiting The radio utilizes a current sense ALC IC U102 to regulate its output power. The current sensing resistor R102 provides a feedback signal to U102. This signal is then compared to the preprogrammed current reference and the error signal is amplified and used to generate a control voltage to control the bias for Driver U101 and final stage RF Power Amplifier, Q110. 4.5. Spurious and Harmonic Emissions Suppression Modulation limiting is accomplished within the custom IC, U404. The limiting action itself occurs at the rails (i.e., 3.3V and ground). Using an opamp with feedback, very hard limiting is obtained. The limited modulation signal is then input through a low-pass splatter filter then to an electronic attenuator within U404 in order to adjust for variations in modulation sensitivities of the frequency synthesizer.

FCC ID: AZ489FT5798 Date: September 29, 2000 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: APPLICATION FOR CERTIFICATION OF TRANSMITTER WITH FCC ID: AZ489FT5798 Attention: Frank Coperich Gentlemen: Motorola Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits it’s application for Certification of the subject transmitter. This transmitter is primarily intended for use as a Portable radio with capabilities for clear communications with a variable transmit power of 1 to 2.5 Watts. The subject transmitter complies with Section 90.203 of the rules in that the operator cannot directly program transmit frequencies using only the unit's normally accessible external controls. Enclosed is a complete Type Acceptance Application. Contact me (954) 723-5793 if you require any additional information. Sincerely, Mike Ramnath FCC Liaison Email: [email protected] EXHIBIT 13

Applicant: Motorola Inc FCC ID: AZ489FT5798 Motorola Inc., 8000 W. Sunrise Blvd., Plantation, FL 33322 Page: 13- 1 Date: December 13, 2000 Mr. Joe Dichoso and Mr. Kwok Chan Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: Response to Correspondence 16937, EA98914, for Transceiver with FCC ID: AZ489FT5798 Dear Mr. Dichoso and Mr. Chan, Motorola Inc herein submits its response to your request for information via correspondence number 16937. Q1. Part 90 SMR devices are required to perform routine RF exposure evaluation according to 2.1091 or 2.1093 to demonstrate compliance. Please submit the test data for the required evaluation. A1. The SAR Test Report, dated 12/12/00, revision A, is submitted at this time. Q2. Page 6 of the safety instruction, in the manual, indicates the antenna should be at least one inch from a person's body when the device is not body-worn, while transmitting. This statement is only applicable when the SAR is due to the antenna and it must also be consistent with the submitted SAR test results. A2. The manual has been revised to reflect ‘If you do not use a body-worn accessory, ensure the antenna and radio product is at least one inch (2.5 cm) from your body when transmitting.’ (See page 6-7 in the attached Users M anual). Q3. The manual indicated numerous accessories, please confirm if all of these accessories are applicable for this device, including carry cases, headsets, antennas etc. A3. All of the accessories listed in the Users Manual, except the antennas, are applicable to this device. Of the 15 antennas listed, only the last two, NAF5037_ and NAF5042_R, are applicable to this device. The SAR report attached reflects the worst case SAR data for the accessories listed in the Users Manual. Contact me at (954) 723-5793 if you require any additional information. Regards, Mike Ramnath FCC Liaison Email: [email protected]

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3 EXTERNAL PHOTOGRAPHS 1EXHIBIT 3-AFront View 3EXHIBIT 3-BBack View 4EXHIBIT 3-CTop View 5EXHIBIT 3-D Side View (PTT Lever ) 6EXHIBIT 3-ESide View (External Mic & Speaker and SCI Jacks) 7EXHIBIT 3-FView Of Battery Contact & FCC Label Location Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-A Front View Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-B Back View Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-C Top View Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-D Side View (PTT Lever) Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-E Side View (External Mic, Speaker & SCI Jacks) Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 3-F View of Battery Contact & FCC Label Location Battery Contact FCC LABEL

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 1 LIST OF EXHIBITS DESCRIPTIONEXHIBITFCC REFERENCE 1.Identification label information12.983-(f) & General Information1A2.981-(c) & 2.1061 1. Production Plans 2. Application References 3. Data Submittal Procedures llCertification Of Data22.907 IIIExternal Photographs32.983-(g) IVBlock Diagrams or Circuit Descriptions42.983-(d)-10,11 1. Carrier Frequency generation and Stabilization 2. Digital Modulation Limiting 3. Modulation Limiting and Post Limiter Filter 4. Means for Output Power Limiting 5. Spurious and Harmonic Emissions Suppression VSchematic Diagrams52.983-(d)-7 VITest Report6 1. Data Index6 2. RF Output Data6A2.985 (a) 3. Modulation Characteristics2.987 (a) a) Audio Response6B b) Low Pass Filter Response6C c) Modulation Limiting6D 4. Occupied Bandwidth6E2.989 5. Conducted Spurious Emissions6F2.991 6. Radiated Spurious Emissions6G2.993 7. Frequency Stability (Temp. & Supply Voltage)6H & 6I2.995 VIITest Set-Up Procedures7 a) Test Equipment Used b) Method Of Measurements c) Emission Designator Information VIIIInstruction Manual82.983-(g) IXInternal Photographs9 XParts List & Tune-up Procedures10 & 10A2.983-(d)-6 & 2.983-(d)-9 XIRF Exposure Information11 XIIOperational Description12 a) Technical Characteristics2.983-(d)-1,2,3,4,5 b) Application XIIICover Letter132.1033 Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 1 IDENTIFICATION LABEL LOCATION XSee the Attached Photograph or Sketch Back Of Radio Back Of Radio Under Belt Clip TYPE XThe label is a paper polyester firm laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 40 inches/oz. The label is laser etched into Urethane paint, exposing the Nickel plating on the Zamak casting substrate. Since no adhesive is required, the label is permanent and tamper proof. MARKINGS (TEXT) XSee the Attached Photograph Refer to Exhibit 3 See Attached Drawing Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 1A GENERAL INFORMATION I.Production Plans -- Pursuant 2.981 Quantity production is planned II.Application References -- Pursuant 2.1061 Reference is made to the following Motorola “Application References” 1. Portable Products and their application 2. Portable Products Transmitter Modulations Methods IIData Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ Rules.

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 9 INTERNAL PHOTOGRAPHS 1EXHIBIT 9-AView of Front Housing Open up 2EXHIBIT 9-BView of Back Casting Open up 3EXHIBIT 9-CView of Top (Front Housing) Side of RF/Controller Board With Shields Removed. 4EXHIBIT 9-DView of Bottom (Casting) Side Of RF/Controller Board With Shields Removed. Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 9-A View With Front Housing Open up Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 9-B View With Back Casting Open up Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 9-C Top (Front Housing) Side of RF/Controller Board with Shields Removed. Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 9-D Bottom (Casting) Side of RF/Controller Board with Shields Removed.

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 12 TRANSMITTER DESCRIPTION 12.1.Transmitter Technical Characteristics -- Pursuant 2.983 (d) a. RF Power Out: 1W to 2.5W Variable Power b. Transmit Frequency Range:806--869 MHz c. Receive Frequency Range:851-869 MHz d. Frequency Stability:1.5 PPM e. Emissions16K0F3E, 14K0F3E f. Spurious Emissions0.31uW g. DC Voltage and Current into7.5 VDC, 1.07 Amps the final RF amplifier stage/stages 12.2.Transmitter Application This transmitter is primarily intended for use in a portable environment. The following features, options, and accessories characterize the Transmitter: a. Power Supply Available: i. NiCd Rechargeable Low Capacity Battery ii. NiCd Rechargeable High Capacity Battery iii. Alkaline Battery iv. NiMH Rechargeable Ultra High Battery v. Lithium Ion Battery b. Antenna Available: i. Helical Antenna ii. Whip antenna c. Squelch Type Available: i. Carrier Squelch ii. Tone “Private Line” iii. Digital “Private Line” iv. DTMF v. MDC vi. Quick Call II d. Microphone - Control: I. Handset/Palm Microphone e. Maximum Transmit Channel Capability: i. 16 Channel f. Housing: i. The transmitter will be housed in the housing shown in the accompanying photographs g. Other Options: i. Time out Timer

Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 10.1 FUNCTION OF RF SEMICONDUCTORS AND OTHER ACTIVE DEVICES Reference Designator Motorola Part no. DescriptionCircuit Application Operating Frequency Radio Circuit Y004802245J68TCXOReference Frequency16.8 MHzFRACN CR2034862824C031SV232TX VCO FREQ806-870MHzFRACN D2014802233J09IMN10Synthesizer Circuit16.8MHzFRACN D2024802233J09IMN10Synthesizer Circuit16.8MHzFRACN Q2004802245J50UMC5NDC SwitchDCFRACN Q2104802245J50UMC5NDC SwitchDCFRACN U2015185963A2763A27FGU16.8MHzFRACN U2475105739X05ADP33005V Voltage RegulatorDCFRACN U2485102463J58LP29803.3 Voltage RegulatorDCFRACN CR2514862824C011SV229VARACTOR806-870MHzVCO CR2524862824C011SV229VARACTOR806-870MHzVCO CR2534862824C011SV229VARACTOR806-870MHzVCO Q2514805218N63BFQ67WRF Transistor806-870MHzVCO Q2524802245J50UMC5NDC SwitchDCVCO U2054802245J58RESONATORResonator900 MHzVCO U2064802245J57RESONATORResonator1.2GHzVCO U2505105750U5450U54Buffer IC740-870MHzVCO CR1014880973Z02MA4PH261Diode Switch806-870MHzPA CR1024880973Z02MA4PH261Diode Switch806-870MHzPA Q1015105385Y7385Y73PA DEVICE806-870MHzPA U1015102463J66RF2103PA DRIVER IC806-870MHzPA U1025185765B01H99S-4Power ControlDCPA U1035185963A15LM50Temperature sensingDCPA CR4404813833C02MMBD6100Reverse Current Protection DCCONTRL Q4004809579E18TP0101TDC SwitchDCCONTRL Q4034880214G02MMBT3904DC SwitchDCCONTRL Q4054802245J54UMG5DC SwitchDCCONTRL Q4104802245J54UMG5DC SwitchDCCONTRL Q4114802245J54UMG5DC SwitchDCCONTRL Q4164809579E18TP0101TDC SwitchDCCONTRL U4005102463J40LP2951ACMM-3.33.3 Voltage RegulatorDCCONTRL U4095102226J55MC68HC11FL0Micro Processor1.83MHzCONTRL U4105102463J57ILC7062CM-33Voltage RegulatorDCCONTRL U4205102463J44TDA8547Audio AmplifierAUDIOCONTRL VR4324805656W08MMQA5V6T1ESD Protection DiodeAUDIOCONTRL VR4334805656W08MMQA5V6T1ESD Protection DiodeAUDIOCONTRL VR4344802245J51BZX284ESD Protection DiodeDCCONTRL VR4454802245J53BZX284ESD Protection DiodeDCCONTRL VR4464802245J53BZX284ESD Protection DiodeDCCONTRL VR4474802245J53BZX284ESD Protection DiodeDCCONTRL Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 10.2 TUNING PROCEDURE Table for tuning frequencies. Test/Tune Freq800 MHz F1805.975 F2815.525 F3825.025 F4838.025 F5850.075 F6860.525 F7870.025 TABLE 1 1.0Reference oscillator warping (Final warp) a) Use SBEP command to adjust warp dac setting to get frquency F7 of table 1. b) Use SBEP command to save warp dac setting in codeplug Dac sensitivity measurement a) Program radio to rx/tx mode, freq=MHz, DAC setting=127 b) Measure if radio lock, Vctrl c) Measure frequency and DAC voltage d) Program DAC=97, measure freq and DAC voltage e) Program DAC=157, measure freq and DAC voltage 2.0TRANSMITTER POWER ADJUSTMENT 2.1General description of PA bias adjustment. Tuning of the PA Bias is required to compensate for FET device tolerances due to lot to lot variation during the FET die fabrication process. To obtain optimum power and efficiency, the bias should be tuned in the factory after it is built or after a repair. a) Program the FRACN to switch off the RF signal by setting VCO IC to battery saver mode. If this is not possible for hardware reasons, set the VCO to RX mode. This step should be performed by setting the bias tuning environment. b) If the VCO IC can’t be set to battery saver mode, set the receive frequency to F1. This should be done automatically by the radio when entering the bias tuning environment. Previous radios required frequency setting by the tuning system. c) Initialize the PCIC for bias tuning by setting the following parameters TX mode switch on the PIN diodes (RX to low, ANO on) set power D2A (D2A#1) to maximum set voltage limit D2A (D2A#2) to minimum set PA bias D2A (D2A#3) to minimum This allows controlling the power control voltage by the voltage limit D2A. The PIN diodes should be on to avoid instabilities. For the same reason the antenna output must be terminated with 50 Ohm termination. In case of PA oscillation an RF induced additional current would lead to tuning inaccuracies. d) Measure the dc current the radio draws from the voltage supply. Note the measured value as VL0 B0 CURRENT. e) Increase the voltage limit D2A (D2A#2) until the dc current exceeds the “VL0 B0 CURRENT“ as specified in table 2 “VL CURRENT“. Note the measured value as “VL B0 CURRENT“. The additional current is drawn by the driver. Applicant: Motorola Inc.FCC ID: AZ489FT5798 EXHIBIT 10.2 f) Increase the PA bias D2A (D2A#3) until the dc current exceeds the “VL B0 CURRENT“ as specified in table 2 “ B CURRENT “ . The additional current is drawn by the FET. After this step a balance between the FET current (gain) and the driver current (gain) has been achieved. The balance is maintained when the RF output power is altered. g) Store the PA bias D2A value in the PA bias softpot. 2.2Transmitter PA bias adjustment procedure a) Set radio environment for PA bias tuning. This relates to steps a)-c) of section 2.1. b) Measure the radio dc current and note the value as “ VL0 B0 CURRENT“. This relates to step d) of section of 2.1. c) Increase the voltage limit D2A (D2A#2) until the dc current exceeds the „VL0 B0 CURRENT“ as specified in table 2 “VL CURRENT“ . Note the measured current as “ VL B0 CURRENT“. This relates to steps e) of section 2.1. d) Increase the PA bias D2A (D2A#3) until the dc current exceeds the „VL B0 CURRENT“ as specified in table 2 “ B CURRENT“. This relates to steps f) of section 2.1. e) Store the PA bias D2A value in the …

Text truncated - open the document above for the full version.