AZ489FT58682 Way Portable Radio

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *NNTN7223G* NNTN7223G MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2013 Motorola Solutions, Inc. All rights reserved. ATTENTION! *6881095C98* 6881095C98-K 6881095C98-K_SafetyP.book Page 1 Tuesday, September 3, 2013 3:56 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C98-K_SafetyP.book Page 2 Tuesday, September 3, 2013 3:56 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C98-K_SafetyP.book Page 3 Tuesday, September 3, 2013 3:56 PM 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 6881095C98-K_SafetyP.book Page 4 Tuesday, September 3, 2013 3:56 PM 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. The PTT button may reside on the radio itself or may be hosted on approved wired or wireless (for example, a Bluetooth enabled remote Push-to-Talk button) accessories. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front…

Text truncated - open the document above for the full version.

MN001810A01- A *MN001810A01* March 2015 EN © 2015 Motorola Solutions, Inc. All rights reserved. Mobile Release 14.0 MTP3250 FEATURE USER GUIDE - USA and Canadian version Contents List of Figures............................................................................................................13 List of Tables.............................................................................................................15 Copyrights.................................................................................................................17 Chapter 1: General Information..............................................................................19 Icon Conventions.........................................................................................................................19 Declaration of Conformity............................................................................................................ 19 Important Safety Information....................................................................................................... 20 Informations importantes sur la sécurité......................................................................................21 Using this Guide.......................................................................................................................... 21 Feature and Service Availability.................................................................................................. 21 Chapter 2: Getting Started.......................................................................................23 Product Technical Information.....................................................................................................23 Before Power On......................................................................................................................... 23 Attaching the Antenna.......................................................................................................24 Inserting the SIM Card......................................................................................................24 Installing the Battery......................................................................................................... 25 Removing the Battery....................................................................................................... 25 Charging the Battery.........................................................................................................26 Charging the Battery By Using a USB Cable....................................................................26 Charging Indicators...........................................................................................................27 Low Battery Indication.......................................................................................................28 Controls and Indicators................................................................................................................28 Display.........................................................................................................................................30 Configurable Idle Screen.................................................................................................. 31 Status Icons.................................................................................................................................31 Powering On the Radio................................................................................................................34 Unlocking Your Radio..................................................................................................................35 Unblocking Your Radio..................................................................................................... 35 Locking/Unlocking the Keys/Buttons........................................................................................... 35 Holding Your Radio......................................................................................................................35 Entering TMO / DMO Mode.........................................................................................................36 Transmit Inhibit Mode.................................................................................................................. 36 Selecting Talkgroups................................................................................................................... 37 Talkgroup Icon Selection............................................................................................................. 37 Activating Talkgroup Scanning.................................................................................................... 38 Contents Send Feedback 3 Broadcast Call............................................................................................................................. 38 Ambience Listening (AL) Call...................................................................................................... 38 One-Touch Button Feature..........................................................................................................38 Terminal Temporary Disable/Enable........................................................................................... 40 Terminal Permanent Disable....................................................................................................... 40 High/Low Audio Toggle................................................................................................................40 Using High Audio.............................................................................................................. 40 Using Low Audio...............................................................................................................41 During the Call..............................................................................................................…

Text truncated - open the document above for the full version.

Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 2 SHEET 1 OF 1 EXHIBIT 2 STATEMENT OF CERTIFICATION – Pursuant to 47 CFR 2.907 and 2.908 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received a Bachelor degree of Computer Science Majoring in Software Engineering from University of Science Malaysia (USM), Malaysia. 2) I have 3 years experience in developing, testing, and certifying Land Mobile Communications Products. NAME: Mohamad Hafiz Abu Hassan SIGNATURE: DATE: 17 th December 2014 POSITION: Electrical Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Gan Chin Kuan SIGNATURE: _ ____ DATE: 17 th December February 2014 POSITION: Senior Staff Engineer

FCC ID: AZ489FT5868 Motorola Solutions Inc. Exhibit 13a 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Date: March 20, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT5868 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) herein submits application for certification of the subject transmitter. This transmitter is primarily intended for use in a portable radio application with capabilities for conventional and 4 to 1 TDMA digital communications (TETRA) with a conducted transmit power listed below: Frequency Rated Power FCC Rule Parts 806-824 MHz 851-869 MHz 1.8 W (Rated power) 2.0 W (Max power) 90 2402 – 2480 MHz 2.0 mW (Rated power) 4.61 mW (Max power) 15C We are requesting certification under Part(s) of the Commission’s Rules listed above to allow operation of this equipment and reference to Report & Order FCC 12-114A1 to permit TETRA certification. In addition, this transmitter is intended for work-related occupational use only under Part 90 of the FCC Rules. MTP3100 series Model (does not offer Bluetooth) and MTP3200 series Model (offers Bluetooth) are identical in hardware except the software controls the mode to turn on / turn off the Bluetooth option. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ489FT5868 Motorola Solutions Inc. Exhibit 13b 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 CONFIDENTIALITY REQUESTED Date: January 2 nd , 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request Regarding Application for Transmitter with FCC ID: AZ489FT5868 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) is requesting for the following Exhibits be held as Permanently Confidential, and not be made routinely available for public inspection: Exhibit 4 Block diagrams Exhibit 5 Schematic Diagrams Exhibit 10 Parts List and Tune Up Procedures Exhibit 12 Operation Description Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Sections 0.457(d), 0.459 and 552(b)(4) of the Freedom of Information Act. Please mark these Exhibits as “Confidential.” Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ489FT5868 Motorola Solutions Inc. Exhibit 13c 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Date: April 20, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: AZ489FT5868 Dear Sir or Madam: This transmitter was design to operate in the following frequency ranges: To aid equipment authorization in other countries that accept the United States FCC Grant for Certification, Motorola (Motorola Solutions Inc) is requesting that the FCC list the above frequency/frequencies under FCC Rule Part 90 on the Grant. For the FCC’s Rule Part 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Federal Emission Designator 806-809* 22K0D1D 22K0D1E 22K0D1W 809-824 x 851-854* 854-869 x *Canada Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 EXTERNAL PHOTOGRAPHS The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View with Display and Keypad. 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view. 3F 7. Bottom view. 3G Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 2 OF 7 Exhibit 3A MTP3100 / MTP3200 / MTP3250 / MTP3150 BACK VIEW WITH BATTERY Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 3 OF 7 Exhibit 3B MTP3100 / MTP3200 MTP3150 / MTP3250 FRONT VIEW Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 4 OF 7 Exhibit 3C MTP3100 / MTP3200 / MTP3150 / MTP3250 BACK VIEW (FCC LABELS) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 5 OF 7 Exhibit 3D MTP3100 / MTP3200 / MTP3250 / MTP3150 SIDE VIEW (RIGHT) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 6 OF 7 Exhibit 3E MTP3100 / MTP3200 / MTP3250 / MTP3150 SIDE VIEW (LEFT) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 3 SHEET 7 OF 7 Exhibit 3F MTP3100 / MTP3200 / MTP3250 / MTP3150 TOP VIEW Exhibit 3G MTP3100 / MTP3200 / MTP3250 / MTP3150 BOTTOM VIEW

Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 1 EXHIBIT 1 IDENTIFICATION LABEL LOCATION See the Attached Photograph or Sketch X Bottom of Radio Top of Radio Back of Radio Back of Radio under Belt Clip TYPE X The label is a polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with the minimum peel strength of 32 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3 for the actual location of the FCC label on the device. X Label Attached Below. See Attached Drawing. MTP3100 model MTP3200 model MTP3250 mode MTP3150 model Figure 1: FCC/IC label

Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 1 OF 7 EXHIBIT 9 INTERNAL PHOTOGRAPHS The following photographs are attached. Exhibit 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D 5. Interface board (Top). 9E 6. Interface board (Bottom) 9F 7. Housing (Front) 9G 8. PCB board with housing (Back) 9H Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 2 OF 7 Exhibits 9A MTP3100 / MTP3200 / MTP3250 / MTP3150 RF board with Shields (Top) Exhibit 9B MTP3100 / MTP3200 / MTP3250 / MTP3150 RF board without Shields (Top) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 3 OF 7 Exhibit 9C MTP3100 / MTP3200 / MTP3250 / MTP3150 RF board with Shields (Bottom) Exhibit 9D MTP3100 / MTP3200 / MTP3250 / MTP3150 RF board without Shields (Bottom) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 4 OF 7 Exhibit 9E MTP3100 / MTP3200 MTP3250 / MTP3150 Interface board (Top) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 5 OF 7 Exhibit 9F MTP3100 / MTP3200 / MTP3250 / MTP3150 Interface board (Bottom) Bluetooth antenna Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 6 OF 7 Exhibit 9G MTP3100 / MTP3200 MTP3250 / MTP3150 Housing (Front) Motorola Solutions Inc FCC ID: AZ489FT5868 / IC: 109U-89FT5868 EXHIBIT 9 SHEET 7 OF 7 Exhibit 9H MTP3100 / MTP3200 / MTP3250 / MTP3150 PCB board with housing (Back)

FCC ID: AZ489FT5868/ IC: 109U-89FT5868 Report ID: SR11933 & SR11932 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Motorola Solutions Inc. EME Test Laboratory Motorola Solutions Malaysia Sdn. Bhd. (455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D. 11900 Bayan Lepas, Penang, Malaysia. Date of Report: 03/24/2015 Report Revision: C Responsible Engineer: Tan CheeChin (EME Section Manager) Report Author: Tan CheeChin (EME Section Manager) Date/s Tested: 01/03/14-03/26/14 Manufacturer/Location: Motorola Solutions Inc., Penang Sector/Group/Div.: EMS Date submitted for test: 12/05/13 DUT Description: Handheld Portable MTP3100 800MHz LKP CLR ROM MTP3250 800MHz FKP GPS/BT CLR ROM Test TX mode(s): TDMA (PTT); CW (Bluetooth) Max. Power output: 2.0W (800 band), 4.62 mW (Bluetooth) Nominal Power: 1.8W (800 band), 2.0 mW (Bluetooth) Tx Frequency Bands: 806 -870 MHz, 2.402 - 2.48GHz Bluetooth Signaling type: TDMA & PI/4DQPSK ; FHSS (Bluetooth) Model(s) Tested: PMUF1620A, PMUF1619A Model(s) Certified: PMUF1620A(H61UCF6TZ1AN), PMUF1619A(H63UCH6TZ7AN) Serial Number(s): 409TNZ0019 Classification: Occupational/Controlled FCC ID: AZ489FT5868; 809- 824MHz, 854-869MHz; 2402-2480MHz IC : 109U-89FT5868; 806-824MHz, 851-869MHz; 2402-2480MHz The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EME Lab Senior Resource Manager, Laboratory Director Approval Date: 3/24/2015 Motorola Solutions Inc. EME Form-SAR -Rpt- Rev. 13.4 Page 1 of 82 FCC ID: AZ489FT5868/ IC: 109U-89FT5868 Report ID: SR11933 & SR11932 Part 1 of 2 1.0 Introduction .................................................................................................................................. 4 2.0 FCC SAR Summary ..................................................................................................................... 4 3.0 Abbreviations / Definitions .......................................................................................................... 4 4.0 Referenced Standards and Guidelines ......................................................................................... 5 5.0 SAR Limits .................................................................................................................................. 6 6.0 Description of Device Under Test (DUT) ................................................................................... 6 7.0 Optional Acccessories and Test Criteria ...................................................................................... 7 7.1 Antennas ............................................................................................................................. 7 7.2 Batteries................................................................................................8 7.3 Body worn Accessories ....................................................................................................... 8 7.4 Audio/ Data cable Accessories ........................................................................................... 8 8.0 Description of Test System ....................................................................................................... 10 8.1 Descriptions of Robotics/Probes/Readout Electronics .................................................... 10 8.2 Description of Phantom(s) ................................................................................................ 11 8.3 Description of Simulated Tissue ....................................................................................... 11 9.0 Additional Test Equipment ...................................................................................................... 12 10.0 SAR Measurement System Validation and Verification ......................................................... 12 10.1 System Validation ........................................................................................................... 12 10.2 System Verification ........................................................................................................ 13 10.3 Equivalent Tissue Test Results ....................................................................................... 13 11.0 Environmental Test Conditions ............................................................................................... 15 12.0 DUT Test Setup and Methodology ......................................................................................... 15 12.1 Measurements ................................................................................................................. 15 12.2 DUT Configuration(s) ..................................................................................................... 16 12.3 DUT Positioning Procedures ....................…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT5868/ IC: 109U-89FT5868 Report ID: SR11933 & SR11932 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Motorola Solutions Inc. EME Test Laboratory Motorola Solutions Malaysia Sdn. Bhd. (455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D. 11900 Bayan Lepas, Penang, Malaysia. Date of Report: 03/24/2015 Report Revision: C Responsible Engineer: Tan CheeChin (EME Section Manager) Report Author: Tan CheeChin (EME Section Manager) Date/s Tested: 01/03/14-03/26/14 Manufacturer/Location: Motorola Solutions Inc., Penang Sector/Group/Div.: EMS Date submitted for test: 12/05/13 DUT Description: Handheld Portable MTP3100 800MHz LKP CLR ROM MTP3250 800MHz FKP GPS/BT CLR ROM Test TX mode(s): TDMA (PTT); CW (Bluetooth) Max. Power output: 2.0W (800 band), 4.62 mW (Bluetooth) Nominal Power: 1.8W (800 band), 2.0 mW (Bluetooth) Tx Frequency Bands: 806 -870 MHz, 2.402 - 2.48GHz Bluetooth Signaling type: TDMA & PI/4DQPSK ; FHSS (Bluetooth) Model(s) Tested: PMUF1620A, PMUF1619A Model(s) Certified: PMUF1620A(H61UCF6TZ1AN), PMUF1619A(H63UCH6TZ7AN) Serial Number(s): 409TNZ0019 Classification: Occupational/Controlled FCC ID: AZ489FT5868; 809-824MHz, 854-869MHz; 2402-2480MHz IC : 109U-89FT5868; 806-824MHz, 851-869MHz; 2402-2480MHz The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EME Lab Senior Resource Manager, Laboratory Director Approval Date: 3/24/2015 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.4 Page 1 of 34 FCC ID: AZ489FT5…

Text truncated - open the document above for the full version.