AZ489FT5870Portable 2-way radio

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *NNTN7223G* NNTN7223G MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2013 Motorola Solutions, Inc. All rights reserved. ATTENTION! *6881095C98* 6881095C98-K 6881095C98-K_SafetyP.book Page 1 Tuesday, September 3, 2013 3:56 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C98-K_SafetyP.book Page 2 Tuesday, September 3, 2013 3:56 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C98-K_SafetyP.book Page 3 Tuesday, September 3, 2013 3:56 PM 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 6881095C98-K_SafetyP.book Page 4 Tuesday, September 3, 2013 3:56 PM 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. The PTT button may reside on the radio itself or may be hosted on approved wired or wireless (for example, a Bluetooth enabled remote Push-to-Talk button) accessories. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT5870 Motorola Solutions Inc. Exhibit 13b 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 CONFIDENTIALITY REQUESTED Date: March 31, 2015 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request Regarding Application for Transmitter with FCC ID: AZ489FT5870 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) is requesting for the following Exhibits be held as Permanently Confidential, and not be made routinely available for public inspection: Exhibit 4 Circuit Descriptions/Block diagrams Exhibit 5 Schematic Exhibit 10 Parts List and Tune Up Procedures Exhibit 12 Transmitter Description Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Sections 0.457(d), 0.459 and 552(b)(4) of the Freedom of Information Act. Please mark these Exhibits as “Confidential.” Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Tel: (954) 723-5422 E-mail: [email protected]

FCC Application for Motorola DLR Series FCC ID: AZ489FT5870/ IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 4 EXHIBIT 3: EXTERNAL PHOTOGRAPHS Figure 3-1.Front View Figure 3-2 Back View FCC Application for Motorola DLR Series FCC ID: AZ489FT5870/ IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 4 Figure 3-3 Top View Figure 3-4 Bottom View FCC Application for Motorola DLR Series FCC ID: AZ489FT5870/ IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 4 Figure 3-5 Side View Figure 3-6 Side View Figure 3-7 Side View Vol. & Monitor Button Accessory Jack Accessory Jack With Dust Cover FCC Application for Motorola DLR Series FCC ID: AZ489FT5870/ IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 4 Figure 3-8. Battery Compartment & Labels

FCC ID: AZ489FT5870/ IC 109U-89FT5870 IDENTIFICATION LABEL LOCATION X See the attached Photograph, and Exhibit 3-8 for the location of the Label on the device. Back of Radio Back of Radio under Belt Clip Please note that Motorola complies with FCC Rule Part 2.907(b) that the label is permanently affixed and is readily visible to the purchaser at the time of purchase. TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/ inch. The label is laser etched into the Urethane paint, exposing the Nickel plating on the Zamak casting substrate. Since no adhesive is required, the label is permanent and tamper-proof. (** - NOTE- The label attached below is a paper polyester film laminate, as described above. This is just for sample purposes, as the actual label is laser etched into the casting) MARKINGS (TEXT) See Photograph, Exhibit 1. EXHIBIT 1 TANAPA: HKUF4006A JAN, 5, 2015 FCC ID: AZ489FT5870 3.7VDC IC MODEL: DLR1020 IC: 109U-89FT5870 S/N: 550PRA0315 Motorola Solutions, Inc Made in China FCC ID: AZ489FT5870/ IC 109U-89FT5870 GENERAL INFORMATION I. Production Plans—Pursuant 2.907(b). Quantity production is planned. II. Application References Reference is made to the following Motorola “Application References” 1. Portable Products and their application. 2. Portable Products Transmitter Modulations Methods. III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ Rules. EXHIBIT 1A

FCC ID: AZ489FT5870/IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 4 EXHIBIT 9: INTERNAL PHOTOGRAPHS Figure 9-1 Bottom Side Internal photo with shields intact. Figure 9-2 Bottom Side Internal photo without shields. FCC ID: AZ489FT5870/IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 4 Figure 9-3 Top Side Internal photo with shields intact. Figure 9-4 Top Side Internal photo without shields. FCC ID: AZ489FT5870/IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 4 Figure 9-5 Top Side Internal photo W/Antenna Figure 9-6 Bottom Side Internal photo W/Antenna FCC ID: AZ489FT5870/IC:109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 4 Figure 9-7 Front Housing Figure 9-8 Board Assembly Figure 9-9 Back Housing

FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 1 of 62 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Motorola Solutions, Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: 04/22/2015 Report Revision: E Responsible Engineer: Deanna Zakharia (Global EME lab Director) Report Author(s): Veeramani Veerapan (Sr.EME Engineer) / William Elliott (Staff EME Engineer)/Jessica Zada (EME Engineer) Date/s Tested: 02/18/2015 – 02/19/2015, 04/03/2015, 04/08/2015 Manufacturer/Location: Hi-P Electronics Pte.Ltd, China Sector/Group/Div.: Others Date submitted for test: 02/12/2015 DUT Description: Handheld Portable , DLR1060 (HKUF4007A), 1watt, 900 MHz, 6CH (BRUS/ BRCAN) Test TX mode(s): CW (PTT) Max. Power output: 1.0 W Nominal Power: 1.0 W Tx Frequency Bands: 902-928 MHz Signaling type: FSK Model(s) Tested: DLR1060 (HKUF4007A) Model(s) Certified: DLR1060 (HKUF4007A) Serial Number(s): 550PRA0335 and 550PRA1033 Classification: General Population/Uncontrolled FCC ID: AZ489FT5870; (902-928 MHz) IC : 109U-89FT5870 The test results clearly demonstrate compliance with FCC General Population/Uncontrolled RF Exposure limits of 1.6 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 2 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 4.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EME Lab Senior Resource Manager, Laboratory Director Approval Date: 4/22/2015 Certification Date: 4/14/2015 Certification No. L1150419 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 2 of 62 Part 1 of 2 1.0 Introduction .................................................................................................................................. 4 2.0 FCC SAR Summary ..................................................................................................................... 4 3.0 Abbreviations / Definitions .......................................................................................................... 4 4.0 Referenced Standards and Guidelines ......................................................................................... 5 5.0 SAR Limits .................................................................................................................................. 6 6.0 Description of Device Under Test (DUT) ................................................................................... 6 7.0 Optional Acccessories and Test Criteria...................................................................................... 7 7.1 Antenna ............................................................................................................................... 7 7.2 Battery ................................................................................................................................. 7 7.3 Body worn Accessory ......................................................................................................... 7 7.4 Audio cable Accessories ..................................................................................................... 7 8.0 Description of Test System ......................................................................................................... 8 8.1 Descriptions of Robotics/Probes/Readout Electronics ....................................................... 8 8.2 Description of Phantom(s) .................................................................................................. 9 8.3 Description of Simulated Tissue ......................................................................................... 9 9.0 Additional Test Equipment ...................................................................................................... 10 10.0 SAR Measurement System Validation and Verification ......................................................... 11 10.1 System Validation ........................................................................................................... 11 10.2 System Verification ........................................................................................................ 11 10.3 Equivalent Tissue Test Results ....................................................................................... 11 11.0 Environmental Test Conditions ............................................................................................... 12 12.0 DUT Test Setup and Methodology ......................................................................................... 13 12.1 Measurements ................................................................................................................. 13 12.2 DUT Configuration(s) .................................................................................................... 13 12.3 DUT Positioning Procedures .....................................................…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Motorola Solutions, Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: 04/22/2015 Report Revision: E Responsible Engineer: Deanna Zakharia (Global EME lab Director) Report Author: Veeramani Veerapan (Sr.EME Engineer) / William Elliott (Staff EME Engineer)/Jessica Zada (EME Engineer) Date/s Tested: 02/18/2015 – 02/19/2015, 04/03/2015, 04/08/2015 Manufacturer/Location: Hi-P Electronics Pte.Ltd, China Sector/Group/Div.: Others Date submitted for test: 02/12/2015 DUT Description: Handheld Portable , DLR1060 (HKUF4007A), 1watt, 900 MHz, 6CH (BRUS/ BRCAN) Test TX mode(s): CW (PTT) Max. Power output: 1.0 W Nominal Power: 1.0 W Tx Frequency Bands: 902-928 MHz Signaling type: FSK Model(s) Tested: DLR1060 (HKUF4007A) Model(s) Certified: DLR1060 (HKUF4007A) Serial Number(s): 550PRA0335 and 550PRA1033 Classification: General Population/Uncontrolled FCC ID: AZ489FT5870; (902-928 MHz) IC : 109U-89FT5870 The test results clearly demonstrate compliance with FCC General Population/Uncontrolled RF Exposure limits of 1.6 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 2 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 4.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 4/22/2015 Certification Date: 4/14/2015 Certification No.: L1150419 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 1 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Appendix D System Verification Check Scans Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 2 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 3 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 4 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 5 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 6 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 7 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Appendix E DUT Scans Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 8 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Assessments at the Body with Body-worn HKLN4616A Table 17 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 9 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Assessments at the Face Table 19 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 10 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Appendix F Shortened Scan of Highest SAR configuration Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 11 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Shortened Scan Table 20 Shortened scan reflects highest SAR producing configuration and is compared to the full scan. Scan Description Referenced Table Test Time (min.) SAR 1g (W/kg) SAR 10g (W/kg) Shorten scan (zoom) 20 7 1.50 1.04 Full scan (area & zoom) 19 14 1.36 0.95 Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 12 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Appendix G DUT Test Position Photos Photos available in Exhibit 7B Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 13 of 14 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Report ID: P2279-EME-00002 Appendix H DUT, Body worn and audio accessories Photos Photos available in Exhibit 7B Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.5 Page 14 of 14

FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 1 of 17 Test Report MEASUREMENT EXHIBIT I Transmitter Output Power 6A II Occupied Bandwidth 6B III Radiated Spurious 6C IV ERP Measured Data 6D V Frequency Behavior 6E VI Frequency Stability 6F VII Test Set Up Photos 6G EXHIBIT 6 FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 2 of 17 EXHIBIT 6A: TRANSMITTER OUTPUT POWER – Pursuant 47 CFR 2.1041 6.1 ISM Band Transmitter Output Power -- Pursuant 47 CFR 2.1033(b)(6) and 15.247(b)(2) ( Test Conducted at Motorola EME accredited lab in FEB 2015) The ISM transmitter operating in the 902-928 MHz band is a frequency hopped, fixed output power type. Output power (as defined in 47 CFR 15.247) is controlled as described in Exhibit 7. Test Freq (MHz) Power (W) 902.525 0.961 915.525 0.995 927.475 0.962 Maximum peak output power rating: 1000 milliwatts (30 dBm), peak power. 6.2 DC Power Used by Final Amplifier Device -- Pursuant 47 CFR 2.1033(c)8) In order to prevent the malfunctions that can occur due to directly measuring the DC characteristics of the final RF amplifying stage, data was obtained by measuring the entire radio DC current and is reported herein for the entire radio. The DC current and the RF output power was a conducted measurement using a power supply set to supply the radio with the nominal battery voltage of 4.0 V. The characteristics were measured during a transmission pulse and are listed in the Table 6- 1: ISM Characteristics 902-928 MHz Power Setting maximum DC Voltage (Volts) 4 DC Current (A) 0.9 Output Power (W) 1.0 Table 6-1 Characteristics for ISM 900 MHz bands FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 3 of 17 EXHIBIT 6B: OCCUPIED BANDWIDTH – Pursuant 47 CFR 2.1041 6.3 900 MHz ISM Band Modulation Characteristics and Necessary Bandwidth In the 900 MHz ISM band, the subject radio makes use of Frequency Shift Keying. The modulation can vary from 2FSK, 4FSK, 6FSK or 8FSK. The data symbols are up-sampled to a rate Ns times the symbol rate, and pulse shaped by a filter having impulse response p n . The pulse shape filter is the cascade of a square pulse, of duration equal to one symbol interval, convolved with a Gaussian filter with 3 dB bandwidth equal to 8000 Hz or BT = 2.5. The pulse-shaped signal is integrated using a backward-summation, and then mapped to in-phase (I) and quadrature (Q) channels using the cosine and sine functions, respectively. A scaling factor of /Ns is required to convert the integrator output to modulated phase. This modulation is shown in Figure X. The pre-modulation filter has the continuous-time impulse response where t is time in seconds, T = 1/3200 is the symbol interval in seconds, B is the 8000 Hz 3-dB bandwidth, and Q(x) is the complimentary distribution function for a Gaussian random variable with zero mean and unit variance, given by The discrete-time impulse response is generated by sampling the continuous-time function. In theory, p(t) has infinite time span, but, for all practical purposes, it is time- limited to the interval Given this, the discrete-time version is generated as where t 0 is the time of the first sample, N s is the number of samples per second, and N p is the filter length. Figure 6-3A. FSK Modulator FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 4 of 17 OCCCUPIED BAND WIDTH (Measured with DLR1060 in December 2014 MSI Plantation Engineering Lab) Figure 6-3B shows the plot of the 8-FSK, traffic channel ISM Band spectrum with its 20 dB bandwidth of 25.65 kHz Figure 6-3B. Occupied bandwidth for 902.525MHz 8FSK Spectrum. FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 5 of 17 OCCCUPIED BAND WIDTH (Measured with DLR1060 in December 2014 MSI Plantation Engineering Lab) Figure 6-3C shows the plot of the 8-FSK, traffic channel ISM Band spectrum with its 20 dB bandwidth of 25.65 kHz Figure 6-3C. Occupied bandwidth for 927.475MHz 8FSK Spectrum The emission requirements specified for operation in the 902-928 MHz ISM Band include a requirement that there is no emission greater than –20 dBc detectable in a 100 KHz bandwidth at all frequencies outside the ISM band. For this measurement the transmitter is tuned to maximum output power at the lowest operating frequency. A similar measurement was made at the upper ISM band edge with the transmitter operating at the maximum ISM band operating frequency. FCC ID: AZ489FT5870/ IC: 109U-89FT5870 Motorola Inc., 8000 W. Sunrise Blvd. Plantation, FL 33322 Page 6 of 17 EXHIBIT 6C: RADIATED SPURIOUS – Pursuant 47 CFR 2.1041 6.4 Radiated Spurious Emissions -- Pursuant 47 CFR 2.1053, 2.1057, 15.247(d), 15.209 ( Test Conducted with DLR1040 at MSI EMC accredited Lab in November 2014) For Radiated Spurious Measurements from 19MHz to 1GHz please see attached TIMCO Folder (TIMCO testing 19MHz to 1GHz) 6.4.1 ISM Band Limits Per 15.247(d) the peak allowable emission shall be less than 10 dBm when measured in a 100 kHz band outside the ISM Band. Measurement Technique – 15.247 TX Spurious Restricted Band Emissions Frequency Hopping - Non-standardized testing Emissions at each freq were maximized by: Following guidelines specified in ANSI C63.4-2003 with regards to emission maximizations [rotation through three orthogonal axes, etc... Procedure for final emissions detection: Freq Span for each harmonic [e.g. 5th harmonic] Start Freq = low channel freq * harmonic# [e.g. 902*5= 4.51 GHz] Stop Freq = Hi Channel freq * harmonic# [e.g. 928*5=4.64 GHz] Detector function = peak Trace = max hold 1) Find an antenna height where the emissions can be discerned 2) Rotate the EUT in 15 deg increments and looking at the band of interest for over 10 sec [sweep time = 15 ms dwell time = 90 ms |10s peak hold observation assures full capture of all channels]. Ex…

Text truncated - open the document above for the full version.

FCC PART 15 ERP TEST REPORT Applicant MOTOROLA SOLUTIONS, INC. Address 8000 WEST SUNRISE BLVD FT. LAUDERDALE FL 33322-9947 USA FCC IC AZ489FT5870 Model Number DLR1060 Product Description 4 CH 900 MHZ FH RADIO Date Sample Received 3/2/2015 Date Tested 3/2/2015 Date Report Issued 3/2/2015 Tested By Cory Leverett Approved By Sid Sanders Test Results PASS FAIL Report Number Version Number Description Issue Date 418UT15TestReport_ERP.docx Rev.1 Initial Issue 3/2/2015 THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW State Road 45 Newberry, Fl 32669 USA Phone: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Table of Contents GENERAL REMARKS ........................................................................................ 3 TEST ENVIRONMENT ...................................................................................... 4 TEST SETUP SUMMARY ................................................................................... 4 EUT SPECIFICATION ....................................................................................... 5 EFFECTIVE RADIATED POWER ......................................................................... 6 TEST EQUIPMENT LIST ................................................................................... 7 APPLICANT: MOTOROLA SOLUTIONS, INC. FCC ID: AZ489FT5870 MODEL: DLR1060 REPORT: M\ MOTO SOL_AZ4\418UT15\418UT15TestReport.docx Page 3 of 7 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. The test results only relate to the item tested. ATTESTATIONS This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025: 2005 requirements. I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Cory Leverett Engineering Project Manager Date: 3/2/2015 TABLE OF CONTENTS APPLICANT: MOTOROLA SOLUTIONS, INC. FCC ID: AZ489FT5870 MODEL: DLR1060 REPORT: M\ MOTO SOL_AZ4\418UT15\418UT15TestReport.docx Page 4 of 7 TEST ENVIRONMENT Test Facility Timco Engineering, Inc. 849 NW State Road 45 Newberry, FL 32669 USA. Test Condition in the laboratory T…

Text truncated - open the document above for the full version.