AZ489FT7006FLN3135A & FLN3134A

68P02966C56-A Please retain for future use BEFORE USING THIS RADIO TERMINAL, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STAN-DARDS. The information provided in this document supersedes information contained in user guides published prior to February 2002. For radio terminals that have been approved as intrinsically safe, read the instruc-tions and information on intrinsic safety in this booklet.Caution: changes or modifications made in the radio terminal, not expressly ap- proved by Motorola, will void the user's authority to operate the equipment. Compliance with RF Energy Exposure StandardsNotice: This radio terminal is intended for use in general population exposure appli-cations, where users have been made aware of the potential for exposure and can exercise control over their exposure. Federal Communication Commission Regulations: The FCC established limits for safe exposure to radio frequency (RF) emissions from portable two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before portable two-way radios can be market-ed in the U.S. When two-way radios are approved for general population exposure environment limits, the FCC requires users to be fully aware of and exercise control over their exposure. Awareness and control of RF exposure can be accomplished by the use of labels, or by education or training through appropriate means, such as information and instructions in user manuals or safety booklets. Your Motorola two-way radio terminal has a RF exposure information label in the battery compart-ment. This user safety booklet includes useful information about RF exposure and helpful instructions on how to control your RF exposures. Your Motorola two-way radio terminal is designed and tested to comply with a num-ber of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio terminal complies with the IEEE (FCC) and ICNIRP exposure limits for general population exposure RF environment. This radio terminal complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re-ceived, including interference that may cause undesired operation.In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio terminal radiates measurable RF energy only while it is transmitting, not when it is receiving or in standby mode. Note: that the approved batteries, supplied with this radio terminal are rated for a 5-5-90 duty cycle (5% transmit-5% receive - 90% standby), even though this radio terminal complies with the FCC general pop-ulation exposure limits at usage factors of up to 50% transmit. Your Motorola two-way radio terminal complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regula- tions; 47CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Elec- tronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radio communications (Electromagnetic Radiation - Human Exposure) Standard 2001. • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) "addi- tional requirements for SMR, cellular and PCS product certification." Compliance and Control Guidelines and Operating Instructions for portable two-way radio terminals To control your exposure and ensure compliance with the general population expo-sure environment limits always adhere to the following Procedures. • If you are not using a body-worn accessory and are not using the radio termi- nal in the intended use position in front of the face, then ensure the antenna MW800 DISPLAYTERMINAL ab

Applicant: Motorola, Inc. FCC ID: AZ489FT7006 Exhibit 8 Exhibit 8 User Manual User Manual MW 800 Display 28 PDF pages total, 22 numbered pages Please find the information required by Part 15.19, 15.21 & 15.105 on page 4 of this PDF file. Note: The Item above follow this cover page a Ownerís Manual MW 800 Display 68P02969C35-O DRAFT March 06 2003 68P02969C35-O @6802969C35@ Owner'sManual800.book Page 1 Tuesday, March 11, 2003 12:19 PM Owner'sManual800.book Page 2 Tuesday, March 11, 2003 12:19 PM MW-800 Display Ownerís Manual COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this instruction manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained In the Motorola products described in this instruction manual may not be copied or reproduced in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product. EPS ñ 34440- B This warranty applies within the fifty (50) United States, the District of Columbia and Canada. LIMITED WARRANTY MOTOROLA COMMUNICATION PRODUCTS If the affected product is being purchased pursuant to a written Communications System Agreement signed by Motorola, the warranty contained in that written agreement will apply. Otherwise, the following warranty applies. I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: Motorola Inc. or, if applicable, Motorola Canada Limited ("Motorola") warrants the Motorola manufactured radio com- munications product, including original equipment crystal devices and channel elements ("Product"), against material defects in material and workmanship under normal use and service for a period of One (1) Year from the date of ship- ment. Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it with the same or equivalent Product (using new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided purchaser notifies Motorola according to the terms of this warranty. Repaired or replaced Product is warranted for the balance of the original applicable warranty period. All replaced parts of the Product shall become the property of Motorola. This express limited warranty is extended by Motorola to the original end user purchaser purchasing the Product for purposes of leasing or for commercial, industrial, or governmental use only, and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by Motorola. Motorola assumes no obliga- tions or liability for additions or modifications to this warranty unless made in writing and signed by an officer of Motor- ola. Unless made in a separate written agreement between Motorola and the original end user purchaser, Motorola does not warrant the installation, maintenance or service of the Product. Motorola cannot be responsible in any way for any ancillary equipment not furnished by Motorola which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equip- ment is expressly excluded from this warranty. Because each system which may use the Product is unique, Motorola disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS: This warranty sets forth the full extent of Motorolaís responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at Motorolaís option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. MOTOROLA DISCLAIMS ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVE- NIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. III. HOW TO GET WARRANTY SERVICE: Purchaser must notify Motorolaís representative or call Motorolaís Customer Response Center at 1-800-247-2346 within the applicable warranty period for information regarding warranty service. IV. WHAT THIS WARRANTY DOES NOT COVER: A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. C) Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D) Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassemblies or repairs (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorolaís normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. Owner'sManual800.book Page 3 Tuesday, March 11, 2003 12:19 PM MW-800 Display Ownerís Manual G) Batteries (they carry their own separate limited warranty). H) Freight costs to the repair depot. I) A Pro…

Text truncated - open the document above for the full version.

E E E X X X H H H I I I B B B I I I T T T 2 2 2 C C C e e e r r r t t t i i i f f f i i i c c c a a a t t t i i i o o o n n n D D D a a a t t t a a a N N N e e e w w w C C C e e e r r r t t t i i i f f f i i i c c c a a a t t t i i i o o o n n n R R R e e e p p p o o o r r r t t t F F F C C C C C C I I I D D D : : : A A A Z Z Z 4 4 4 8 8 8 9 9 9 F F F T T T 7 7 7 0 0 0 0 0 0 6 6 6 Product Name M M M W W W 8 8 8 0 0 0 0 0 0 – – – D D D I I I S S S P P P L L L A A A Y Y Y M M M o o o d d d e e e l l l : : : F F F L L L N N N 3 3 3 1 1 1 3 3 3 4 4 4 A A A , , , F F F L L L N N N 3 3 3 1 1 1 3 3 3 5 5 5 A A A Tests Performed for M M M o o o t t t o o o r r r o o o l l l a a a , , , I I I n n n c c c . . . 8000 West Sunrise Blvd. Ft. Lauderdale, Florida 33322 USA Prepared by: Q Q Q u u u a a a l l l i i i T T T e e e c c c h h h E E E M M M C C C L L L a a a b b b o o o r r r a a a t t t o o o r r r y y y 30 Hasivim St, Petah-Tikva, 49130, Israel Tel: 972-3-926 8443 Fax: 972-3-926 6550 1633.01 FCC ID: AZ489FT7006 EMC Lab Date: 10.03.2003 Motorola Inc. Exhibit 2 - 2 of 2 MW 800 – DISPLAY Model: FLN3134A, FLN3135A February 10, 2003 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd. Columbia, MD 21046 Re: FCC ID: AZ489FT7006 Applicant: Motorola, Inc. Models: FLN3134A, FLN3135A Gentlemen: QualiTech Experts Ltd. has tested the above referenced transmitter in accordance with the applicable requirements contained in the Parts 2 and 15 of Title 47, CFR. To the best of my knowledge, these tests were performed using the criteria established in ANSI or other Industry standards. The measurements demonstrate that the Intentional Radiator, a Bluetooth device, complies with the limits established in Part 15.247. The digital device emissions were measured and met the Part 15.109, Class B limit. The receiver is exempt from the Part 15.109 requirements as it is above 960 MHz. The applicable rule sections are listed in the following test report. The anechoic chember (FCC Reg.No:102724), used for the radiated emissions measurements is located at 30, Hasivim St., Petah Tikva, Israel. The site information required by Part 2.948 of the FCC rules measured in accordance with ANSI C63.4-1992 was most recently renewed. Sincerely, Y.Zucker QA and Lab. Manager QualiTech EMC Laboratory Email: [email protected] om

FCC ID: AZ489FT7006 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA. Confidentiality Request 19 th March 2003 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT7006. Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath FCC Liaison Tel: (954) 723-5793 E-mail: [email protected] EXHIBIT 13b

FCC ID: AZ489FT7006 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA. Date: 19 th March 2003 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT7006. Gentlemen: Motorola Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. The MW800 Display model: FLN 3134A and Model FLN 3135A are ruggedized Mobile LCD display (XGA and SVGA) unit which contain a Bluetooth intentional radiator previously approved under Part 15.247 with FCC ID: AZ489FT7005. We have submitted the appropriate test data for this Intentional Radiator, for the six required items including exhibits for SAR, EIRP & spurious emissions. We have also referenced the twelve items which are common to all Bluetooth devices and included the list, verbatium, provided by the Mr. Joe Dichoso of the FCC’s OET Laboratory. The two models are identical as defined by Part 2.908, except for cosmetic appearance changes only. The intended use of this transceiver includes applications covered in the Code of Federal Regulations Title 47, Part 15. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. Contact Mike Ramnath at (954) 723-5793 if you require any additional information. Sincerely, /s/ Mike Ramnath Mike Ramnath FCC Liaison Email: [email protected] FCC ID: AZ489FT7006 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA. EXHIBIT 13

Northwest EMC TCB Compliance Opinion Revision 1/3/03 MOTI0001 Information about the Applicant Company Name Motorola, Inc. Address 8000 West Sunrise Blvd City, State, Zip Ft. Lauderdale, FL 33322 Requested By Mike Ramnath Job Number MOTI0001 Model FLN 3134A and FLN 3135A FCC ID AZ489FT7006 Agent Mike Ramnath - Motorola Approval Type Certification Equipment Type FHSS (Bluetooth radio) Rule Part 47CFR15.247 Overview Certification is sought for Motorola’s MW800 Display model: FLN 3134A and identical Model FLN 3135A. Both models contain the same radio; they simply have different display options. Both are ruggedized LCD display (XGA and SVGA) unit which contain a Bluetooth TM Intentional Radiator, not previously approved under 47 CFR 15.247. The Bluetooth TM radio is intended for short distance communication with peripheral devices. Both units contain a Bluetooth intentional radiator previously approved under Part 15.247 with FCC ID: AZ489FT7005. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. April 3, 2003 Dean Ghizzone, President Date Northwest EMC TCB Compliance Opinion Revision 1/3/03 MOTI0001 Findings and Resolution Item #1 The list of measurement equipment did not show test equipment capable of radiated emissions scans up to the 10 th harmonic of the radio’s transmit frequency. There is no pre- amp included in the equipment list to cover the 18 GHz – 26 GHz frequency range. There is also no data that would allow confirmation of adequate sensitivity at that frequency range without use of a preamp. Further, while it is a low power device, it is usually required in order to prevent overload use a of high pass filter for the spurious radiated emissions measurements. Resolution 4-3-03 Applicant provided updated equipment list and specified a test procedure to ensure overload protection. Item #2 Applicant had not submitted completed Form 410 Resolution 4-3-03 Applicant provided signed and completed form. Item #3 Applicant had not submitted completed Form 415 Schedule A&B Resolution 4-3-03 Applicant provided signed and completed forms. Item #4 No power spectral density data. Resolution 4-7-03 The test report exhibit was updated to delete the power spectral density test data. The applicant requested that the subject device be filed as a FHSS. The applicant conferred with Joe Dichoso of the FCC who confirmed this was acce ptable. Northwest EMC TCB Compliance Opinion Revision 1/3/03 MOTI0001 Opinion Specification Requirements Description 47 CFR 15.247(b)(5) and 2.1093 RF Exposure Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has demonstrated compliance in the form of an Exhibit. Reference: Exhibit 11 Specification Requirements Description 47 CFR 15.247 Occupied Bandwidth Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. According to the FCC’s Interpretations Database, “Frequency hoppers in the 2.4 GHz band are required to use a minimum of 15 non-overlapping channels. The hopping channel bandwidth can be wider than 1 MHz as long as the channels do not overlap and all emissions stay within the 2400-2483.5 MHz band. (ref. email sent to [email protected] 10/08/2002)” The subject radio uses more than 15 hopping channels, none of which overlap. The maximum 20 dB occupied bandwidth is less than 1 MHz. Reference: Exhibit 6 Specification Requirements Description 47 CFR 15.247(b)(1) Power Output Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit 6 Specification Requirements Description 47 CFR 15.247(c) Spurious Emissions, Antenna Conducted Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Exhibit 6 Northwest EMC TCB Compliance Opinion Revision 1/3/03 MOTI0001 Specification Requirements Description 47 CFR 15.247(c), 15.205, & 15.209 Spurious Emissions, Radiated Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: Problem see list above. Reference: Exhibit 6 Specification Requirements Description 47 CFR 15.207 AC Powerline Conducted Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The radio is mounted into a vehicle and acquires its’ DC power from the vehicle electrical system. Therefore, the Applicant submitted no AC Powerline Conducted data. Reference: N/A Specification Requirements Description 47 CFR 15.203 Antenna Requirement Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has demonstrated compliance in the form of exhibits. Reference: Exhibits 12 Specification Requirements Description 47 CFR 2.925 FCC ID Label and Location Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has demonstrated compliance in the form of exhibits. Reference: Exhibit 1 Specification Requirements Description 47 CFR 2.1033(b) Application for Certification Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted all the required exhibits to sufficiently demonstrate compliance of his product to the relevant FCC rules. Reference: Exhibits 1 through 13

1-5 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Exhibit 3 EXHIBIT 3 EXTERNAL PHOTOS Front View of Display 2-5 Exhibit 3 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Rear View of MW 800 3-5 Exhibit 3 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Enlarged FCC IDENTIFICATION LABEL Label Location: Back side of the display unit chassis Please note that two FCC identifier labels are submitted for the two models that are identical as defined by Section 2.908. No visual change between the models. Note: label size is about approximately 3 times actual size. FCC ID: AZ489FT7006 identifier label for the Model: FLN3135A 4-5 Exhibit 3 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY FCC ID: AZ489FT7006 identifier label for the Model: FLN3134A 5-5 Exhibit 3 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY 3D View of the display unit

Applicant: Motorola, Inc. FCC ID: AZ489FT7006 Exhibit 1 LIST OF EXHIBITS DESCRIPTION EXHIBITSREFERENCE I.Identification label Information12.1033 (b) 7 & 2.925 & General Information1A 1. Production Plans2.1031 2. Application ReferencesN/A 3. Data submittal Procedure 4. Similar Certified Transmitter II.Certification Data2 III.External Photographs32.1033 (b) 7 IV.Block Diagrams (Circuit Diagrams) 42.1033 (b) 5 V. Schematic Diagrams & Antenna Assembly52.1033 (b) 5 VI.Test Report62.1033 (b) 6 Eleven Common Bluetooth Items6 Six tests required615.247 (a, b, c, g, h) 1) The Occupied Bandwidth Section 15.247(a)!ii 2) Conducted Output Power Section 15.247(b)1 3) EIRP limit Section 15.247(b)3 4) RF safety Section 15.247(b)4 see Exhibit XII 5) Spurious Emissions Section 15.247 (c) 6) Power Spectral Density in Acquistion Mode VII.Test Set-up Procedures72.1041 VIII.Instruction Manual82.1033 (b) 3 IX.Internal Photographs92.1033 (b) 7 X.Part List and Tune Up Procedures10N/A XI.RF Exposure Information112.1093 & 15.247 (b)4 XII.Operational Description122.1033 (b) 1, 2, 4, 8 Antenna Requirements1215.203 1. Technical Characteristics 1 - 5 2. Application XIII. Cover Letter, Action Requested13 Cover Letter, Authorization to sign FCC Form 73113 Please NOTE: Exhibits 4, 5 and 12 are requested to held confidential Applicant: Motorola, Inc. FCC ID: AZ489FT7006 Exhibit 1 EXHIBIT 1. FCC IDENTIFICATION LABEL Required Under Section: 47 CFR 2.1033(c) 11 Please note: Two FCC Identifier labels are submitted on this page for the two physically and electrically identical models, as defined by Section 2.908. FCC ID: AZ489FT7006 Identifier label for the Model: FLN3135A & Model: FLN3134A The labels above are175 % of actual size. NOTE: The differences between models are cosmetic only. Applicant: Motorola, Inc. FCC ID: AZ489FT7006 Exhibit 1 Label Location : Back side of the display. Applicant: Motorola, Inc. FCC ID: AZ489FT7006 Exhibit 1 EXHIBIT 1A. General Information --- 47 CFR 2.1031 and 2.1061. 1A.1. Production Plans -- Pursuant 47 CFR 2.1031 Quantity production is planned. 1A.2.Application References -- Pursuant 47 CFR 2.1061 Reference is made to the following Motorola "Application References" 1. Part 15.247 Intentional Radiators and their application 1A.3.Data Submittal Procedure Data located in Exhibit 6 is supplied in accordance with Part 2, Sub- part J and Part 15, Sub-part C of the Commissions ’ rules and will be submitted electronically. 1A.4.Similar, currently Certified Intentional Radiator The MW 800 display is manufactured by Motorola, Inc. The 800 display contains within one Bluetooth intentional radiator. The device is based on the Broadcom single chip solution and meets all Bluetooth Qualification Testing, BQB. As such it is similar in operation to other devices that adhere to the Bluetooth standard and have recently been Certified by other manufacturers using the Broadcom single chip solution.

1-6 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Exhibit 9 EXHIBIT 9 INTERNAL PHOTOS Enlarged view Bluetooth PCB both sides of board with top shield in place. 2-6 Exhibit 9 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Enlarged view of the Bluetooth PCB both sides of the board top shield removed 3-6 Exhibit 9 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Back cover removed Bluetooth PCB location Bluetooth Board Bluetooth Antenna 4-6 Exhibit 9 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Bluetooth Board Bluetooth Antenna 5-6 Exhibit 9 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Rear Cover (left) Main board and inverter board (right) Front Cover Screen and Internal Chassis Front Cover Internal Chassis and Screen 6-6 Exhibit 9 FCC: AZ489FT7006 Applicant: Motorola, Inc MW 800 DISPLAY Function Board Control Board Main Board Inverter Board

Applicant: MOTOROLA INC FCC ID: AZ489FT7006 RF EXPOSURE INFORMATION: In accordance with 47 CFR 2.1093 (c), this transmitter is categorically exempted from routine environmental evaluation for RF Exposure prior to equipment authorization or use since it does not fall within the scope of 2.1093 (c). Further, a device having a transmit output power level of 1.6 mW or less will not exceed the General Population exposure limit of 1.6mW/g even if 100% of the energy is deposited into the human body. EXHIBIT 11

E E E X X X H H H I I I B B B I I I T T T V V V I I I T T T e e e s s s t t t R R R e e e p p p o o o r r r t t t – – – N N N e e e w w w C C C e e e r r r t t t i i i f f f i i i c c c a a a t t t i i i o o o n n n F F F C C C C C C I I I D D D : : : A A A Z Z Z 4 4 4 8 8 8 9 9 9 F F F T T T 7 7 7 0 0 0 0 0 0 6 6 6 T T T e e e s s s t t t R R R e e e p p p o o o r r r t t t N N N o o o : : : M M M O O O T T T 1 1 1 0 0 0 0 0 0 2 2 2 0 0 0 3 3 3 Issued on: February 10, 2003 Product Name M M M W W W 8 8 8 0 0 0 0 0 0 – – – D D D I I I S S S P P P L L L A A A Y Y Y M M M o o o d d d e e e l l l : : : F F F L L L N N N 3 3 3 1 1 1 3 3 3 4 4 4 A A A , , , F F F L L L N N N 3 3 3 1 1 1 3 3 3 5 5 5 A A A Tested under P P P a a a r r r t t t 1 1 1 5 5 5 . . . 2 2 2 4 4 4 7 7 7 Tests Performed for M M M o o o t t t o o o r r r o o o l l l a a a , , , I I I n n n c c c . . . 8000 West Sunrise Blvd. Ft. Lauderdale, Florida 33322 USA Prepared by: Q Q Q u u u a a a l l l i i i T T T e e e c c c h h h E E E M M M C C C L L L a a a b b b o o o r r r a a a t t t o o o r r r y y y 30 Hasivim St, Petah-Tikva, 49130, Israel Tel: 972-3-926 8443 Fax: 972-3-926 6550 1633.01 EMC Test Report: MOT100203 EMC Lab FCC ID: AZ489FT7006 Date: 10.03.2003, Rev. 1 Motorola Inc. 2 of 20 MW 800 – DISPLAY Model: FLN3134A, FLN3135A T T T a a a b b b l l l e e e o o o f f f C C C o o o n n n t t t e e e n n n t t t 1. GENERAL ........................................................................................................................................................3 1.1. Output power and channel separation of a Bluetooth device in the different Operating modes: ............................................................................................................................ 3 1.2. Frequency range of a Bluetooth device: ........................................................................ 3 1.3. Co-ordination of the hopping sequence in data mode to avoid simultaneous Occupancy by multiple transmitters: ................................................................................................ 4 1.4. Example of a hopping sequence in data mode:.............................................................. 4 1.5. Equally average use of frequencies in data mode and behavior for short Transmissions: 4 1.6. Receiver input bandwidth and behavior for repeated single or multiple packets:......... 5 1.7. Channel Separation in hybrid mode............................................................................... 5 1.8. Derivation and examples for a hopping sequence in hybrid mode ................................ 6 1.9. Receiver input bandwidth and synchronization in hybrid mode: .................................. 6 1.10. Spread rate 1 data rate of the direct sequence signal ................................................. 6 1.11. Spurious emission in hybrid mode............................................................................. 6 2. TEST RESULTS ...............................................................................................................................................7 2.1. 20 dB BANDWIDTH .................................................................................................... 7 2.2. CONDUCTED PEAK OUTPUT POWER (CW MODE) ........................................... 10 2.3. CONDUCTED SPURIOUS EMISSIONS (CW MODE)............................................ 13 2.4. FIELD STRENGTH OF SPURIOUS RA…

Text truncated - open the document above for the full version.