AZ489FT7050PORTABLE 2-WAY RADIO

English Product Safety and RF Energy Exposure Booklet for Portable Two-Way Radios BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRINSIC SAFETY ON PAGE 11 OF THIS BOOKLET. Caution Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *6881095C98* 6881095C98-F *NNTN7223C* NNTN7223C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2011 Motorola Solutions, Inc. All rights reserved. 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission (FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. • FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 • Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. Guidelines: • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • DO NOT use this device if the operational requirements described herein are not met. 5 English Operating Instructions • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposur…

Text truncated - open the document above for the full version.

APX 4000 User Guide Model 3 68012004058-A English mASTRO ® APX™ 4000 Series Digital Portable RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 68012004065) to ensure compliance with RF energy exposure limits. Radio Controls Radio On/OffZones and Channels Receiving and TransmittingSending an Emergency Alarm * Default emergency button press timer is set to 1 second. This timer is programmable, see page 66 in the user guide for details.To exit emergency at any time, press and hold the Emergency button. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ! C a u t i o n Battery Multi Function Knob (MFK)*:Primary Feature:_________________Secondary Feature:_________________ Accessory Connector Microphone Antenna • On – Press and hold the MFK until the display lights up. • Off – Press and hold the MFK until you see Power off? , then press Menu Select button below Yes . • Zone – Zone scroll to desired zone. • Channel – Channel scroll to desired channel. Data Feature Button Side Button 1__________ Side Button 2__________PTT Button MicrophoneTop Lightbar IndicatorTop Side (Select) Button__________ Main Speaker Main Display Top (Orange) Button___________ Bluetooth Pairing Indicator LED Keypad Menu Select Buttons 4-Way Navigation Button Home Button 1 Select zone/channel. 2 Listen for a transmission.ORPress and hold Volume Set button. ORPress Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. 1 Press and hold the Emergency button. 2 The display shows Emergency and the current zone/channel. You hear a short, medium-pitched tone, and the LED blinks momentary red. 3 When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency. *PMLN6070A* PMLN6070A ©2011 by Motorola Solutions, Inc. All Rights Reserved. 10/111303 East Algonquin Road, Schaumburg,Illinois 60196, U.S.A. English Sending an Emergency Call To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call To exit emergency at any time, press and hold the Emergency button. Display Status Icons 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency c ontinues until you: Press and hold the Emergency button to exit emergency state.ORPress and release the PTT button to exit the Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode. Receiving a call or data.Transmitting a call or data. u t Blinks when the battery is low.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. 8 v O M H OR . i j The vote scan feature is enabled.On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call.On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable.On = User is currently associated with the radio. Off = User is currently not associated with the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin.Data activity is present.Bluetooth is ready.Bluetooth is connected to the device. k m l G no b a Menu Navigation < or > to Menu Entry. { , | , or } directly below Menu Entry to select. H to exit. U or D to scroll through sub-list. { , | , or } directly below Menu Entry to select. Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303, East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: APX 4000 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harm…

Text truncated - open the document above for the full version.

FCC ID: AZ489FT7050 EXHIBIT 13A SHEET 1 15 th December 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ489FT7050, APX4000. Gentlemen: Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Portable Radio environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency ranges: 764 - 805 MHz: 1.0 – 2.65 Watts (Nominal) 806 – 869 MHz: 1.0 – 3.30 Watts (Nominal) We are requesting Certification under Part 90 of the Commission’s Rules to allow operation of this equipment. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793. Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ489FT7050 EXHIBIT 13b SHEET 1 REQUEST FOR CONFIDENTIALITY 15 th December 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality for Transmitter with FCC ID:AZ489FT7050 Dear Sir / Madam, Motorola Solutions is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected]

FCC ID: AZ489FT7050 EXHIBITS 13C _________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 15 th December 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX4000 Portable 2-Way radio was designed to operate in the frequency band 764-869 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola is requesting that the FCC lists the frequencies 764-775 MHz, 793-805 MHz, 806-824 MHz, and 851-869 MHz under FCC Rule Parts 90 on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 guidance, “as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies”. Frequency Range (MHz) Part 90 Federa l Grant Notes Emission Designator Rule Part 80 & 90 764- 776/794-806* 764- 775 x x EF, BH 11K0F3E, 8K10F1D, 8K10F1E, 8K10F1W 793- 805 x x EF, BH 16K0F3E, 20K01E 806- 824 x EF, BH “”” 851- 869 x EF, BH “”” * Canada Sincerely, Mike Ramnath Manager, Regulatory Compliance Email: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 1 OF 8 EXHIBIT 3 The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View with Display and Keypad. 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F 7. Antennas 3G Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 2 OF 8 BACK VIEW WITH BATTERY EXHIBIT 3A Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 3 OF 8 FRONT VIEW WITH DISPLAY AND KEYPAD EXHIBIT 3B Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 4 OF 8 BACK VIEW (FCC LABELS) EXHIBIT 3C Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 5 OF 8 SIDE VIEW (RIGHT) EXHIBIT 3D Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 6 OF 8 SIDE VIEW (LEFT) EXHIBIT 3E Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 7 OF 8 TOP VIEW EXHIBIT 3F Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 3 SHEET 8 OF 8 7/800 MHz Antennas

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or Sketch X Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. FCC Label Model 3 Full Keypad

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 1 OF 7 EXHIBIT 9 Internal Photographs The following photographs are attached. Exhibit 1. RF board without & with Shields (Top). 9A 2. RF board without & with Shields (Bottom). 9B 3. Keypad Board without shield (Bottom). 9C 4. Keypad Board with Shields (Bottom). 9D 5. Keypad Board (Top). 9E 6. RF board with chassis and housing (front side). 9F 7. RF Board with chassis and housing (back side). 9G Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 2 OF 7 EXHIBIT 9A RF board without & with Shields (Top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 3 OF 7 EXHIBIT 9B RF board without & with Shields (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 4 OF 7 EXHIBIT 9C Keypad board without Shields (Bottom) EXHIBIT 9D Keypad board with Shields (Bottom) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 5 OF 7 EXHIBIT 9E Keypad Board (Top) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 6 OF 7 EXHIBIT 9F RF board with chassis and housing (front side) Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 9 SHEET 7 OF 7 EXHIBIT 9G Chassis and Housing (back side)

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 1 OF 41 EXHIBIT 6 INDEX OF SUBMITTED MEASURED DATA This exhibit contains the measured data for this equipment as follows: EXHIBIT 6A – RF Power Output EXHIBIT 6B – Audio Frequency Response 6B-1 –775.9875 MHz, 12.5 kHz Channel Spacing 6B-2 –851.0125 MHz, 12.5 kHz Channel Spacing 6B-3 –775.9875 MHz, 25 kHz Channel Spacing 6B-4 –851.0125 MHz, 25 kHz Channel Spacing EXHIBIT 6C – Audio Low Pass Filter Response 6C-1 –775.9875 MHz, 12.5 kHz Channel Spacing 6C-2 –851.0125 MHz, 12.5 kHz Channel Spacing 6C-3 –775.9875 MHz, 25 kHz Channel Spacing 6C-4 –851.0125 MHz, 25 kHz Channel Spacing EXHIBIT 6D – Modulation Limiting 6D-1 –775.9875 MHz, 12.5 kHz Channel Spacing 6D-2 –851.0125 MHz, 12.5 kHz Channel Spacing 6D-3 –775.9875 MHz, 25 kHz Channel Spacing 6D-4 –851.0125 MHz, 25 kHz Channel Spacing EXHIBIT 6E – Occupied Bandwidth 6E-1 –775.9875 MHz, 12.5 kHz Channel Spacing (Analog Voice) 6E-2 –851.0125 MHz, 12.5 kHz Channel Spacing (Analog Voice) 6E-3 –775.9875 MHz, 25 kHz Channel Spacing (Analog Voice) 6E-4 –851.0125 MHz, 25 kHz Channel Spacing (Analog Voice) 6E-5 –775.9875 MHz, 12.5 kHz Channel Spacing (Digital Data) 6E-6 –851.0125 MHz, 12.5 kHz Channel Spacing (Digital Data 6E-7 –775.9875 MHz, 12.5 kHz Channel Spacing (Digital Voice) 6E-8 –851.0125 MHz, 12.5 kHz Channel Spacing (Digital Voice) 6E-9 –775.9875 MHz, 12.5 kHz Channel Spacing (Digital TDMA) 6E-10 –851.0125 MHz, 12.5 kHz Channel Spacing (Digital TDMA) 6E-11 –775.9875 MHz, (Digital Voice Encryption) 6E-12 –851.0125 MHz, (Digital Voice Encryption) EXHIBIT 6F – Adjacent Channel Coupled Power Ratio 6F-1 - 794.0125 MHz, Analog 12.5 kHz Channel Spacing 6F-2 - 794.0125 MHz, Analog 25 kHz Channel Spacing 6F-3 - 794.0125 MHz, APCO 12.5 kHz Channel Spacing, Digital Data 6F-4 - 794.0125 MHz, APCO 12.5 kHz Channel Spacing, Digital Voice 6F-5 - 794.0125 MHz, APCO 12.5 kHz Channel Spacing, Digital TDMA EXHIBIT 6G – Radiated Spurious Emissions 6G-1 - High Power 764.1025 MHz & 775.9875MHz, 12.5 kHz Channel Spacing 6G-2 - High Power 794.0125 MHz, 12.5 kHz Channel Spacing 6G-3 - High Power 823.9875 MHz & 851.0125MHz, 12.5 kHz Channel Spacing 6G-4 - High Power 869.8875 MHz, 12.5 kHz Channel Spacing 6G-5 - High Power 764.1025 MHz & 775.9875MHz, 25 kHz Channel Spacing 6G-6 - High Power 794.0125 MHz, 25 kHz Channel Spacing 6G-7 - High Power 823.9875 MHz & 851.0125MHz, 25 kHz Channel Spacing 6G-8 - High Power 869.8875 MHz, 25 kHz Channel Spacing Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 2 OF 41 EXHIBIT 6H – 1559-1605MHz Radiated Emissions (GNSS) EXHIBIT 6I – Conducted Spurious Emissions 6I-1 - High Power 764.1025 MHz, 1 2.5 kHz Channel Spacing 6I-2 - High Power 775.9875 MHz, 1 2.5 kHz Channel Spacing 6I-3 - High Power 794.0125 MHz, 12.5 kHz Channel Spacing 6I-4 - High Power 823.9875 MHz, 12.5 kHz Channel Spacing 6I-5 - High Power 851.0125 MHz, 12.5 kHz Channel Spacing 6I-6 - High Power 869.8875 MHz, 12.5 kHz Channel Spacing 6I-7 - High Power 764.1025 MHz, 25 kHz Channel Spacing 6I-8 - High Power 775.9875 MHz, 25 kHz Channel Spacing 6I-9 - High Power 794.0125 MHz, 25 kHz Channel Spacing 6I-10 - High Power 823.9875 MHz, 25 kHz Channel Spacing 6I-11 - High Power 851.0125 MHz, 25 kHz Channel Spacing 6I-12 - High Power 869.8875 MHz, 25 kHz Channel Spacing EXHIBIT 6J – Power Line Conducted Emissions 6J-1 – Line1 6J-2 – Line2 EXHIBIT 6K – Frequency Stability (Volt/Temp) 6K-1– 775.9875 MHz vs. Supply Voltage 6K-2 – 851.0125 MHz vs. Supply Voltage 6K-3 – 775.9875 MHz vs. Temperatures 6K-4 – 851.0125 MHz vs. Temperatures Note: Data was tested to show compliance to RSS102, RSS119, and RSS210, as applicable. Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 3 OF 41 EXHIBIT 6A RF Conducted Power Output Data -- Pursuant 47 CFR 2.1046(a), 2.1033(c)(6), 2.1033(c)(7) and 2.1033(c)(8) Frequency = 764.0125 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.24 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.52 Amps Output RF power 2.99 Watts DC Voltage 7.50 Volts DC Current 1.75 Amps Frequency = 775.9875 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.23 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.51 Amps Output RF power 2.99 Watts DC Voltage 7.50 Volts DC Current 1.74 Amps Frequency= 794.0125 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.22 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.49 Amps Output RF power 2.99 Watts DC Voltage 7.50 Volts DC Current 1.73 Amps Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 4 OF 41 Frequency = 809.0125 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.16 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.49 Amps Output RF power 3.60 Watts DC Voltage 7.50 Volts DC Current 1.85 Amps Frequency = 851.0125 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.13 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.41 Amps Output RF power 3.60 Watts DC Voltage 7.50 Volts DC Current 1.73 Amps Frequency= 869.8875 MHz: Output RF power 1.0 Watts DC Voltage 7.50 Volts DC Current 1.08 Amps Output RF power 2.0 Watts DC Voltage 7.50 Volts DC Current 1.31 Amps Output RF power 3.60 Watts DC Voltage 7.50 Volts DC Current 1.66 Amps Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 5 OF 41 EXHIBIT 6B Transmit Audio Response - Pursuant 47 CFR 2.1047 and 2.1033(c) (13) Audio Frequency Response (Freq: 775.9875MHz, ChSp: 12.5 kHz) Exhibit 6B-1 Audio Frequency Response (Freq: 851.0125MHz, ChSp: 12.5 kHz) Exhibit 6B-2 Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 6 OF 41 Audio Frequency Response (Freq: 775.9875MHz , ChSp: 25kHz) Exhibit 6B-3 Audio Frequency Response (Freq: 851.0125MHz , ChSp: 25kHz) Exhibit 6B-4 Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 6 SHEET 7 OF 41 Transmit Low Pass Filter Fr…

Text truncated - open the document above for the full version.

Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 7 SHEET 1 OF 6 Measurement Procedure & Test Equipment Used Except where otherwise stated, all measurements are made following the Electronic Industries Association (EIA) Minimum Standard for Portable/Personal Land Mobile Communications FM or PM Equipment 25-1000 MHz-(EIA/TIA-603). This exhibit presents a brief summary of how the measurements were made, the required limits, and the test equipment used. The following procedures are presented with this application. 1. Test Equipment List x 2. RF Power Output Data x 3. Audio Frequency Response x 4. Audio Low Pass Filter Response x 5. Modulation Limiting x 6. Occupied Bandwidth x 7. Adjacent Channel Coupled Power Ratio x 8. Radiated Spurious Emissions x 9. 1559-1605MHz Radiated Emissions (GNSS) x 10. Conducted Spurious Emissions x 11. Power Line Conducted Emissions x 12. Frequency Stability (Volt/Temp) x Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 7 SHEET 2 OF 6 Test Equipment List Pursuant To FCC Rules 2.947 (d) 1) Computer: DELL Latitude D600 Notebook, Window 2000. 2) Spectrum Analyzer: Agilent E4445A, 3 Hz – 13.2 GHz 3) Spectrum Analyzer: HP 8560E, 30 Hz - 2.9 GHz. 4) Dynamic Signal Analyzer: HP35665A 5) RF Signal Generator: E4420BB, 250 kHz – 2 GHz RF Signal Generator. 6) Modulation Analyzer. HP 8901B. 7) Audio Analyzer .HP 8903B. 8) Power Meter. HP437B. Sensor 80401A 9) Oscilloscope. Phillips PM3382. 10) Multimeter: Hewlett Packard 34401A. 11) DC Power Supply: Hewlett Packard 6623A 12) Directional Coupler: Hewlett Packard 778D, Dual Directional Coupler. 13) Temperature Chamber: VOTSCH, VT4010. 14) 30 dB attenuator: MCE/Weinschel, model 33-30-34 15) HP35665A Dynamic Signal Analyzer 16) High Pass Filter, Mini-Circuit NHP 300 & 25W 17) MCE/Weinschel 1429-4, 50 ohms terminating load RF Power Output Pursuant to FCC Rules 2.1046 (a) Method of Measurement The RF power output is measured with the transmitter adjusted in accordance with the tune-up procedure outlined in Exhibit 10 to give the value of voltage and current as specified in Exhibit 12 as required by 2.1033(c) (8). A 50-ohm RF attenuator of proper power rating was used as a load for making these measurements. The power measurements are made using an Agilent series E4419B RF power meter and 30 dB attenuator. Audio Frequency Response Pursuant FCC Rules 2.1047 (a) Method of Measurement Operate the transmitter under standard test conditions and monitor the output with a frequency deviation meter or calibrated test receiver. With 1000 Hz sine wave audio input applied through a dummy microphone circuit, adjust the audio input to give 20% of full rated system deviation. Maintaining a constant input voltage, vary the input frequency from 300 to 3000 Hz, and observe the deviation. Minimum Standard The audio frequency response shall not vary more than +1 or -3 dB from 300 to 3000 Hz from a true 6 dB per octave pre-emphasis characteristic as referenced to 1000 Hz level, with the exception of a permissible 6 dB/octave roll off below 500 Hz. Equivalent to TIA/EIA 603 Section 5.2.6.2 mask. Applicant: Motorola Solutions Inc. FCC ID: AZ489FT7050 EXHIBIT 7 SHEET 3 OF 6 Audio Low Pass Filter Response Pursuant FCC Rules 2.1047 (a) Method of Measurement The audio oscillator portion of an HP8903B audio analyzer is connected to the input of the post limiter low pass filter. The oscillator is adjusted, at 1000 Hz and level 16dB greater than that required to produce standard test modulation. The output of the low pass filter is measured with an HP35665A dynamic signal analyzer. The response is swept between the limits of 1000 Hz - 30000 Hz. Oscillator level is chosen to be as high as possible and that will not cause limiting at any frequency, and maintaining a constant input level versus frequency. FCC Limits -- Per applicable rule parts. 450 to 869 MHz & VHF Marine. Frequencies between 3 kHz and 20 kHz shall be attenuated greater than the attenuation at 1 kHz by 60 1og 10 (f/3) dB. Frequencies above 20 kHz shall be attenuated at least 50 dB. Modulation Limiting Pursuant FCC Rules 2.1047 (b) Method of Measurement The transmitter shall be adjusted for full rated system deviation. Adjust the audio input for 60% of rated system deviation at 1000 Hz. Using this level as a reference (0 dB) vary the audio input level from the reference to a level 20 dB above it for modulation frequencies between 300 and 3000 Hz in 100Hz steps. Record the system deviation obtained as a function of the input level. FCC Limits Minimum Standard - The transmitter modulation must not exceed rated system deviation at any audio frequency input or reasonable change in input level. In the exhibit, 100% corresponds to the maximum rated system deviation for the given channel bandwidth. Occupied Bandwidth Pursuant to FCC Rules 2.1049 Method of Measurement Data on occupied bandwidth is presented in the form of a spectrum analyzer photograph, which illustrates the transmitter sidebands. For analog signals, the refer…

Text truncated - open the document above for the full version.