AZ492FT4896Mobile 2-way Radio

English Product Safety and RF Energy Exposure Booklet for Mobile Two-Way Radios Installed in Vehicles or as Fixed Site Control Stations ATTENTION! The information provided in this document supersedes the general safety information contained in user guides published prior to January 2008. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. © 2005 – 2009 by Motorola, Inc. All rights reserved. 10/09 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. *6881095C99* 6881095C99-G *NNTN7851B* NNTN7851B 6881095C99-G.book Page 1 Tuesday, October 27, 2009 1:25 PM 2 English RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C99-G.book Page 2 Tuesday, October 27, 2009 1:25 PM 3 English Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola two-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standard Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C99-G.book Page 3 Tuesday, October 27, 2009 1:25 PM 4 English Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • Institute of Electrical and Electronic Engineers (IEEE) C95.1-2005 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003 • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular, and PCS product certification” RF Exposure Compliance and Control Guidelines and Operating Instructions To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures. Guidelines: • User awareness instructions should accompany device when transferred to other users. • DO NOT use this device if the operational requirements described herein are not met. 6881095C99-G.book Page 4 Tuesday, October 27, 2009 1:25 PM 5 English Instructions: •Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is transmitting. To r…

Text truncated - open the document above for the full version.

APX 7500 User Guide O9 Control Head 68007024014-B O9Head_68007024014_b.book Page 1 Wedn esday, October 20, 2010 2:28 PM O9Head_68007024014_b.book Page 2 Wedn esday, October 20, 2010 2:28 PM English mASTRO ® APX™ 7500 Series Digital Mobile RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C9 9 ) to ensure compliance with RF energy exposure limits. Radio On/OffAdjusting VolumeSelecting a Zone Selecting a ChannelRadio Controls Receiving and Transmitting Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. Press the Power On/Off button to toggle the power on or off. Turn the Volume knob clockwise to increase volume or counterclockwise to decrease the volume. 1 > or < to Zone . Press the Menu Select button directly under the Zone . 2 U or D button until the desired zone is displayed. 3 Press the Menu Select button directly below Select to confirm the displayed zone. 4 Press the PTT button to begin transmitting on the displayed zone channel. ! C a u t i o n 1 > or < to Channel . Press the Menu Select button directly under the Channel . 2 U or D button until the desired channel is displayed. 3 Press the Menu Select button directly below Select to confirm the selected channel. 4 Press the PTT button to begin transmitting on the displayed zone channel. 1 Turn the Mode Knob to scroll to the required channel. 2 Press PTT button to transmit on the selected zone channel. 5 4 1 2 3 6789 11 10 12 13 14 15 16 17 18 Siren Control ButtonsProgrammable Buttons (Top)Response SelectorDirectional ButtonsOrange ButtonPublic Address ButtonKeypadData Feature ButtonMode Knob4-Way Navigation ButtonHome ButtonSatus IconsProgrammable Buttons (Bottom)Menu Select ButtonsVolume KnobDisplay Backlight Control ButtonsLED IndicatorsPower On/Off Button 1 Take the microphone off hook. 2 Select zone/channel. 3 Listen for a transmission.ORTurn the Volume Knob . OR> or < to Monitor then press the Menu Select button directly below Monitor and listen for activity. 4 Adjust volume, if necessary. 5 Press the PTT button to transmit; release to receive. 12 3 456789 10 11 12131415161718 © 2010 by Motorola, Inc. All Rights Reserved. 06/101301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A. *PMLN5711A* PMLN5711A O9Head_68007024014_b.book Page 3 Wedn esday, October 20, 2010 2:28 PM English Sending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button. Sending an Emergency Call (Trunking Only) To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Display Status Icons 1 Press the Emergency button. A tone sounds and the display shows EMERGENCY and the current zone or channel. 2 A dispatcher acknowledgment ACK RECEIVED display follows. AND, Trunking Only:A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller. 3 Press and hold the emergency button or the PTT button to return to normal operation. 1 Press the Emergency button. 1 A tone sounds and the display shows EMERGENCY and the current zone or channel. ORA talk prohibited tone sounds when the selected channel does not support emergency. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT to end the transmission. 1 Press the Emergency button to activate the silent alarm feature. 2 The display does not change; the LED does not light up, and there is no tone. Receiving a call or dataTransmitting a call or dataReceived an Individual Call.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.Voice muting the affiliated trunking talkgroup or selected conventional channel.On = Enabled Off = Disabled L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. F O M K H OR . i Radio is in the view or program mode.On steady = View mode. Blinking = Program mode. The vote scan feature is enabled.On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. On = User is currently associated with the radio. Off = User is currently not associated with the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present.Indicates that the text entry is currently in hexadecimal mode.Alternates between red and blue when the lightbar is on. k m l G no Menu Navigation < or > to Menu Entry. - directly below Menu Entry to select. U or D to scroll through sub-list. - directly below Menu Entry to select. H to exit. O9Head_68007024014_b.book Page 4 Wedn esday, October 20, 2010 2:28 PM Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-10…

Text truncated - open the document above for the full version.

Chapter 5 Motorcycle Radio Installation NOTE:The motorcycle radio installation is not applicable for 100W radios and O9 control heads. 5.1Motorcycle Radio Description The motorcycle model includes all the same components in the standard radio, with the exceptions listed in the model charts in the APX 7500 Basic Service Manual (6875964M01). The following paragraphs describe the unique items provided with the motorcycle models. NOTE:The APX 7500 Basic Service Manual (6875964M01) includes complete parts lists and parts numbers for all parts shown in the exploded views in this chapter.  A small label is included with the motorcycle radio, which can be placed on the radio to identify it as a motorcycle radio. The label should be placed on a flat and protected area to avoid damage during handling. See Figure 5-1. Figure 5-1. Identification of a Motorcycle Radio by Using a Label 5.1.1Transceiver Enclosure The transceiver is mounted in the weather-resistant enclosure that consists of a bottom housing and a hinged top cover. The top cover has a locking latch that requires a key to open. The enclosure is mounted above the rear motorcycle wheel, oriented so that the lock is forward and the hinged cover opens toward the rear of the motorcycle. The bottom housing has a grommeted hole for cable entry and weep holes to permit water drainage. The enclosure is mounted on the motorcycle with a universal mounting plate and shock and vibration isolators. A large, braided ground-strap (installed between the mounting plate bolts and the motorcycle frame) grounds the transceiver. 5.1.2Control/Display Unit All radio functions, except push-to-talk (PTT), are activated from the control head, which also is weather-resistant. The control head and the external speaker are mounted for easy access near the center of the handlebars. The control head is positioned for unobstructed viewing, and it may be tilted on the horizontal axis for ease of viewing. The microphone cable port on the front of the control head is plugged and is not used. 6878215A01 5-2Motorcycle Radio Installation: Motorcycle Radio Description 5.1.3Control Head Cable The control-head cable connects the control head to the transceiver. The cable is routed along the motorcycle’s frame and has weather-resistant connections at both ends. Excess cable is coiled under the transceiver inside the weather-resistant enclosure. Each end of the cable is strain-relieved with jackscrews at the control head and the transceiver. The cable is shielded to reduce the effects of radio frequency interference and ignition sense noise. 5.1.4Microphone A weather-resistant, palm microphone and coiled cord plug into a pigtail connector on the control cable. The microphone attaches to a hang-up bracket located within easy reach of the motorcycle rider. The coiled cord is long enough to be operated by someone standing next to the motorcycle, yet short enough to not interfere with the motorcycle’s steering or operation. 5.1.5Keypad Mic The Mobile Keypad Microphone (Mic) is a full keypad handheld microphone. The keypad on this microphone is intended to assist in navigating through the menus on its parent device, as well as entering information such as phone numbers and menu picks. 5.1.6External Speaker A 3.2-ohm, 10-watt-rated-audio-power, external speaker is mounted on the front of the motorcycle. The speaker cable is routed along the motorcycle frame to the transceiver’s rear accessory connector. A sealed, weather-resistant, speaker-muting (toggle) switch is mounted on top of the speaker. The external speaker connects to the rear accessory connector of the transceiver. 5.1.7Headset Capability The motorcycle radio is compatible with headset accessories that would provide hands-free operation of the radio. Motorola does not manufacture headset equipment, but provides the interconnection for headset equipment with the motorcycle radio. Aftermarket headset equipment is available through Motorola (see Appendix A: Replacement Parts Ordering). 5.1.8Antenna The antenna(s) are mounted on top of the transceiver’s weather-resistant enclosure.  The enclosure’s metal lining acts as the antenna’s ground plane. 5.1.9Ignition Sense (ACC) Wire The ignition sense wire connects to the motorcycle’s fuse box and is routed along the motorcycle frame to the transceiver’s rear accessory connector. The radio is wired so that transmission is inhibited if the motorcycle’s ignition sense switch is off.  If the PTT switch is pressed with the ignition sense off, a low-frequency tone sounds. The receiver is controlled by the control head on/off switch. To avoid possible injury to hearing, the audio setting in the mobile radio MUST be confirmed, if the Motorola mobile radio is used with any motorcycle helmet headset. See CPS Help for details. ! C a u t i o n 6878215A01 Motorcycle Radio Installation: Installation Overview5-3 5.2Installation Overview 5.2.1General All APX 7500 radios are tested and inspected before shipment. It is, however, suggested that the transmitter frequency, deviation, and power output be checked at the time of installation. It is the license holder’s responsibility to ensure that the operating parameters of his station comply with applicable laws governing radio communications equipment. For tests and alignment procedures, refer to the appropriate service manual (refer to “Related Publications” on page vi). Generally, the installation of the motorcycle radio takes place in the following parts: • Mounting the universal mounting plate and related hardware at the rear of the motorcycle; • Mounting the control head, speaker, microphone, and related hardware forward on the motorcycle; • Routing the power cable, control-head cable, speaker cable, and ignition sense cable to the weather-resistant enclosure; • Mounting the weather-resistant enclosure and radio chassis, and connecting the cables; • Mounting the antenna(s) to the weather-resistant enclosure. A universal mounting plate, supplied…

Text truncated - open the document above for the full version.

APX 7500 User Guide O9 Control Head 68007024014-B O9Head_68007024014_b.book Page 1 Wedn esday, October 20, 2010 2:28 PM O9Head_68007024014_b.book Page 2 Wedn esday, October 20, 2010 2:28 PM English mASTRO ® APX™ 7500 Series Digital Mobile RadiosQuick Reference Card Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C9 9 ) to ensure compliance with RF energy exposure limits. Radio On/OffAdjusting VolumeSelecting a Zone Selecting a ChannelRadio Controls Receiving and Transmitting Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. Press the Power On/Off button to toggle the power on or off. Turn the Volume knob clockwise to increase volume or counterclockwise to decrease the volume. 1 > or < to Zone . Press the Menu Select button directly under the Zone . 2 U or D button until the desired zone is displayed. 3 Press the Menu Select button directly below Select to confirm the displayed zone. 4 Press the PTT button to begin transmitting on the displayed zone channel. ! C a u t i o n 1 > or < to Channel . Press the Menu Select button directly under the Channel . 2 U or D button until the desired channel is displayed. 3 Press the Menu Select button directly below Select to confirm the selected channel. 4 Press the PTT button to begin transmitting on the displayed zone channel. 1 Turn the Mode Knob to scroll to the required channel. 2 Press PTT button to transmit on the selected zone channel. 5 4 1 2 3 6789 11 10 12 13 14 15 16 17 18 Siren Control ButtonsProgrammable Buttons (Top)Response SelectorDirectional ButtonsOrange ButtonPublic Address ButtonKeypadData Feature ButtonMode Knob4-Way Navigation ButtonHome ButtonSatus IconsProgrammable Buttons (Bottom)Menu Select ButtonsVolume KnobDisplay Backlight Control ButtonsLED IndicatorsPower On/Off Button 1 Take the microphone off hook. 2 Select zone/channel. 3 Listen for a transmission.ORTurn the Volume Knob . OR> or < to Monitor then press the Menu Select button directly below Monitor and listen for activity. 4 Adjust volume, if necessary. 5 Press the PTT button to transmit; release to receive. 12 3 456789 10 11 12131415161718 © 2010 by Motorola, Inc. All Rights Reserved. 06/101301 E. Algonquin Rd., Schaumburg,IL 60196-1078, U.S.A. *PMLN5711A* PMLN5711A O9Head_68007024014_b.book Page 3 Wedn esday, October 20, 2010 2:28 PM English Sending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button. Sending an Emergency Call (Trunking Only) To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Display Status Icons 1 Press the Emergency button. A tone sounds and the display shows EMERGENCY and the current zone or channel. 2 A dispatcher acknowledgment ACK RECEIVED display follows. AND, Trunking Only:A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller. 3 Press and hold the emergency button or the PTT button to return to normal operation. 1 Press the Emergency button. 1 A tone sounds and the display shows EMERGENCY and the current zone or channel. ORA talk prohibited tone sounds when the selected channel does not support emergency. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT to end the transmission. 1 Press the Emergency button to activate the silent alarm feature. 2 The display does not change; the LED does not light up, and there is no tone. Receiving a call or dataTransmitting a call or dataReceived an Individual Call.The more stripes, the stronger the signal strength for the current site (trunking only).Direct radio to radio communication or connected through a repeater.On = Direct Off = Repeater This channel is being monitored.Voice muting the affiliated trunking talkgroup or selected conventional channel.On = Enabled Off = Disabled L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list.Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. F O M K H OR . i Radio is in the view or program mode.On steady = View mode. Blinking = Program mode. The vote scan feature is enabled.On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. On = User is currently associated with the radio. Off = User is currently not associated with the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present.Indicates that the text entry is currently in hexadecimal mode.Alternates between red and blue when the lightbar is on. k m l G no Menu Navigation < or > to Menu Entry. - directly below Menu Entry to select. U or D to scroll through sub-list. - directly below Menu Entry to select. H to exit. O9Head_68007024014_b.book Page 4 Wedn esday, October 20, 2010 2:28 PM Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-10…

Text truncated - open the document above for the full version.

MOTOROLA FCC ID: AZ492FT4896 EXHIBIT 2 STATEMENT OF CERTIFICATION The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) MSEE University of South Florida 2) 12 years experience in the development, testing and certification of Land Mobile Communications Products NAME: Anbuselvan Kuppusamy DATE: 10 December 2010 POSITION: Senior Staff Electrical Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME: Michael Lenzen DATE: 10 December 2010 POSITION: Engineering Manager

FCC ID: AZ492FT4896 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 21 st December 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ492FT4896, APX7500. Gentlemen: Motorola Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Mobile Transmitter environment with capabilities for clear and coded communications with a variable transmit power of 4-45 Watts (Nominal) in the frequency ranges of 450-520 MHz. To aid equipment authorization in foreign countries which accept United States FCC Grant for equipment authorization, Motorola is asking the FCC to list on the FCC Grant the following frequencies: 450-520 MHz. We are requesting Certification under Part 22, 74 and 90 of the Commission’s Rules to allow operation of this equipment. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793. Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected] EXHIBIT 13a

FCC ID: AZ492FT4896 ______________________________________________________________________________ Motorola Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. CONFIDENTIALITY REQUEST Date: 21 st December 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ492FT4896. Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune-up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected] Exhibit 13b

FCC ID: AZ492FT4896 ____________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 21st December 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX7500 Mobile 2-Way radio was designed to operate in the frequency band 450–520 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola is requesting that the FCC lists the frequencies 450–520 MHz on the FCC Grant. This radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC-OET KDB Publication 634817guidance, the grantee acknowledges that devices operating on unauthorized frequencies are a violation of the FCC Rules. Frequency Range (MHz) Part 90 Part 22 Part 74 Federal Grant Notes Emission Designator Rule Part 80 & 90 450-454* x x EF, BC 8K10F1D/F1E/F1W, 11/16K0F3E, 20K0F1E 454-455* x EF, BC “”” 455-456* x EF, BC “”” 456-460* x x EF, BC “”” 460-462.5375* x EF, BC “”” 462.7375-467.5375* x EF, BC “”” 467.7375-470* x EF, BC “”” 470-512 x x x EF, BC “”” 512-520 x EF, BC “”” * Canada Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected] EXHIBIT 13c

8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. USA FCC ID: AZ492FT4896 Date: 4 th February 2011 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Response to FCC’s Correspondence Reference Number 39472 for FCC ID: AZ492FT4896 Dear Stan and Tim: Below are the responses to FCC Correspondence 39472. 0). Fyi in below SR8945 = car-mount MPE, SR8954 = bike-mount MPE Q1). User manual pdf pg 13 of 142 has "6881095C98" for RF exposure instructions, while pg 3 has "6881095C99" - please revise for consistency where appropriate, or submit "... C98" version ("... C99" version is already in this filing). R1). A revised manual is provided. Q2) SR8945 pg 4 mentions 2.1091(d) and Gen. Pop./Uncontrolled, whereas el…

Text truncated - open the document above for the full version.