AZ492FT4916Mobile 2-Way Radio

English RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION! The information provided in this document supersedes the general safety information contained in user guides published prior to January 2008. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. *6881095C99* 6881095C99-J *NNTN7851D* NNTN7851D Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2005 – 2012 Motorola Solutions, Inc. All rights reserved. 6881095C99_SafetyM_Eng.fm Page 1 Tuesday, March 20, 2012 2:43 PM 2 English RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C99_SafetyM_Eng.fm Page 2 Tuesday, March 20, 2012 2:43 PM 3 English Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola two-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standard Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/ controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C99_SafetyM_Eng.fm Page 3 Tuesday, March 20, 2012 2:43 PM 4 English Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. • FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 • Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures. Guidelines: • User awareness instructions should accompany device when transferred to other users. • DO NOT use this device if the operational requirements described herein are not met. 6881095C99_SafetyM_Eng.fm Page 4 Tuesday, March 20, 2012 2:43 PM 5 English Instructions: •Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX, stop talking. The red LED will extinguish when the radio stops tran…

Text truncated - open the document above for the full version.

APX TM TWO-WAY RADIOS APX MOBILE O2 CONTROL HEAD USER GUIDE English m ASTRO ® APX™ O2 Control Head Mobile Radio Quick Reference Card RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Station which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. Radio Controls Radio On/Off Adjusting Volume Selecting a Zone Selecting a Channel Receiving and Transmitting Sending an Emergency Alarm To exit emergency at any time, press and hold the Emergency button or the PTT button. Power Button LED Indicators Emergency Button* Multi-function Knob (MFK)* Home Button Menu Select Buttons* Accessory Port (Microphone) *These controls/buttons are programmable. Dimmer Button Up & Down Buttons* Press the Power button to turn the radio on or off. If volume is set as the primary mode, 1Turn the MFK clockwise to increase volume or counterclockwise to decrease the volume. If volume is not set as the primary mode, press the MFK once and repeat step 1. If zone is set as the primary mode, 1Turn the MFK until the display shows the desired zone and press the PTT button to begin transmitting on the displayed zone. If zone is not set as the primary mode, press the MFK once and repeat step 1. OR 2> or < (on the keypad mic.) to scroll to Zone. 3Press the Menu Select button directly below Zone. 4Rotate the MFK or D or U to the desired zone. 5Press the Menu Select button directly below Sel or the  button (on the keypad mic.) to confirm the selected zone number. 6Press the PTT button to begin transmitting on the displayed zone. If channel is set as the primary mode, 1Turn the MFK until the display shows the desired channel and press the PTT button to begin transmitting on the displayed channel. If channel is not set as the primary mode, press the MFK once and repeat step 1. OR 2> or < (on the keypad mic.) to scroll to Chan. 3Press the Menu Select button directly below Chan. 4Rotate the MFK or press D or U to the desired channel. 5Press the Menu Select button directly below Sel or the  button (on the keypad mic.) to confirm the channel. 6Press the PTT button to transmit on the displayed channel. 1Take the microphone off the hook. 2Select zone/channel. 3Listen for a transmission. OR > or < (on the keypad mic.) to Mon then press the Menu Select button directly below Mon and listen for activity. 4Adjust volume, if necessary. 5Press the PTT button to transmit; release to receive. 1Press the Emergency button. A tone sounds and the display alternates Emergency and the home display. 2A dispatcher acknowledgment Ack received display follows. AND, Trunking Only: A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller. *PMLN6193C* PMLN6193C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012, 2013 by Motorola Solutions, Inc. All Rights Reserved. 06/13 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. English Sending an Emergency Call (Trunking Only) To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Display Status Icons 1Press Emergency button. 2A tone sounds and the display alternates Emergency and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. 3Press and hold the PTT button. Speak clearly into the microphone. 4Release the PTT to end the transmission. 1Press the preprogrammed Emergency button to activate the silent alarm feature. 2The display does not change; the LED does not light up, and there is no tone. Receiving a call or data. Transmitting a call or data. Received an Individual Call. The more stripes, the stronger the signal strength for the current site (trunking only). u t F V Direct radio-to-radio communication or communication through a repeater. On = Direct Off = Repeater This channel is being monitored. Voice muting the affiliated trunking talkgroup or selected channel. On = Enabled Off = Disabled L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list. Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority- Two Channel during scan. The vote scan feature is enabled. O M K HOR . i j k On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. Inverted = User is currently associated with the radio. On = Packet data is activated. Off = Packet data is deactivated. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present. MFK is in Mode Change feature Turn the MFK to change channel. MFK is in Volume Change feature Turn the MFK to adjust the volume. m l G n o Menu Navigation < or > to Menu Entry (on the keypad mic.). g directly below Menu Entry to select. H to exit. U or D to scroll through sub-list. g directly below Menu Entry to select. Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown…

Text truncated - open the document above for the full version.

Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Statement of Certification The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) BEng(Hons) Multimedia University 2) 3 years experience in the development, testing and certification of Land Mobile Communications Products NAME : Leong Ying Xuan SIGNATURE :__________________________ DATE : July, 1, 2013 POSITION :Senior Electrical Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME : Teoh Yee Teng SIGNATURE :_________________________ DATE : July, 1, 2013 POSITION :Engineering Manager EXHIBIT 2

Federal Communications CommissionDA 12-642 Before the Federal Communications Commission Washington, D.C. 20554 In the Matter of Implementation of Sections 309(j) and 337 of the Communications Act of 1934 as Amended Promotion of Spectrum Efficient Technologies on Certain Part 90 Frequencies ) ) ) ) ) ) ) WT Docket No. 99-87 RM-9332 ORDER Adopted: April 25, 2012Released: April 26, 2012 By the Chief, Wireless Telecommunications Bureau, Chief, Public Safety and Homeland Security Bureau, and Chief, Office of Engineering and Technology: I.INTRODUCTION 1.In this Order, we waive, on our own motion, the January 1, 2013 deadline for private land mobile radio (PLMR) licensees in the 470-512 MHz band to migrate to narrowband (12.5 kHz or narrower) technology. 1 We also waive a related rule pertaining to manufacture and importation of PLMR equipment.We take this action in light of recent legislation directing the Commission to reallocate spectrum in the 470-512 MHz band. II. BACKGROUND 2.In 1995, the Commission adopted rule changes to promote the efficient use of the PLMR service and facilitate the introduction of advanced technologies. 2 To promote the transition to a more efficient narrowband channel plan, the Commission provided, inter alia, that “only increasingly efficient equipment” would be approved. 3 The Commission did not set a date after which it would no longer approve equipment with a wideband (25 kHz) mode, or after which such equipment could no longer be manufactured or used. 4 The Commission contemplated that, as systems reached the end of their service life and new radios were needed, users would migrate to the narrower bandwidth multi-mode radios in 1 See Implementation of Sections 309(j) and 337 of the Communications Act of 1934 as Amended,Second Report and Order and Second Further Notice of Proposed Rulemaking, WT Docket No. 99-87, 18 FCC Rcd 3034 (2003) (Second R&O); Implementation of Sections 309(j) and 337 of the Communications Act of 1934 as Amended,Third Memorandum Opinion and Order, Third Further Notice of Proposed Rule Making and Order, WT Docket No. 99- 87, 19 FCC Rcd 25045 (2004) (Third MO&O). Specifically, these narrowbanding deadlines apply to frequencies in the 150.8-162.0125 MHz, 173.2-173.4 MHz, and 421-512 MHz bands. Narrowbanding in the 150.05-150.8 MHz, 162-174 MHz, and 406.1-420 MHz bands, which are allocated primarily for Federal Government use, is governed by a different schedule. See Amendment of Parts 2 and 90 of the Commission’s Rules to Provide for Narrowband Private Land Mobile Radio Channels in the 150.05-150.8 MHz, 162-174 MHz, and 406.1-420 MHz Bands that Are Allocated for Federal Government Use, Report and Order, ET Docket No. 04-243, 20 FCC Rcd 5793 (2005); 47 C.F.R. § 90.265. Similarly, the narrowbanding requirements for 700 MHz public safety narrowband systems are subject to a different schedule, and are not affected by this proceeding. See47 C.F.R. §§ 90.203(m), (n), 90.535. 2 SeeReplacement of Part 90 by Part 88 to Revise the Private Land Mobile Radio Services and Modify the Policies Governing Them, Report andOrder and Further Notice of Proposed Rule Making, PR Docket No. 92-235, 10 FCC Rcd 10076, 10077 ¶ 1 (1995). 3 Id.at 10081 ¶ 7. 4 Id.at 10100 ¶ 40. Federal Communications CommissionDA 12-642 2 order to avoid the adjacent-channel interference that could occur from systems using the adjacent narrowband channels. 5 3.Subsequently,the Commission determined that the 1995 rules failed to provide adequate incentive to realize the Commission’s spectrum efficiency goals in these bands, and stronger measures would be required to bring about a timely transition to narrowband technology. 6 The Commission therefore amended the rules to provide that, by January 1, 2013, Industrial/Business and Public Safety Radio Pool licensees in the 150-174 MHz and 421-512 MHz bands must migrate to 12.5 kHz channel bandwidth or utilize a technology that achieves equivalent efficiency. 7 In addition, beginning January 1, 2013, the manufacture or import of equipment capable of operating with only one voice path per 25kHz of spectrum, i.e., equipment that includes a 25 kHz mode, will be prohibited. 8 4.Congressrecently enacted the Middle Class Tax Relief and Job Creation Act of 2012. 9 Section 6103 of the legislation provides that, not later than nine years after the date of enactment, the Commission shall “reallocate the spectrum in the 470-512 MHz band (referred to in this section as the ‘T- Band spectrum’) currently used by public safety eligibles as identified in section 90.303 of title 47, Code of Federal Regulations” and “begin a system of competitive bidding under section 309(j) of the Communications Act of 1934 (47 U.S.C. 309(j)) to grant new initial licenses for the use of the spectrum.” 10 Italso provides that “relocation of public safety entities from the T-Band spectrum” shall be completed not later than two years after completion of the system of competitive bidding. 11 III. DISCUSSION 5.Pursuant to Section 1.925(b)(3) of our Rules, we may waive specific requirements of the Commission’s Rules if it is shown that (a) the underlying purpose of the rules would not be served or would be frustrated by application to the instant case, and that a grant of the requested waiver would be in the public interest; or (b) in view of unique or unusual factual circumstances, application of the rules would be inequitable, unduly burdensome or contrary to the public interest, or the applicant has no reasonable alternative. 12 In the instant case, Section 6103 of the legislation specifically requires the eventual relocation of public safety entities from the 470-512 MHz band, and also raises issues about the disposition of theband generally. Pending further action by the Commission, however, there is substantial uncertainty regarding whether application of the narrowbanding deadline in the T-Band would continue to serve its original purpose. Continuing to require narrowbanding cou…

Text truncated - open the document above for the full version.

FCC ID: AZ492FT4916 EXHIBIT 13a ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 4 th July 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ492FT4916, APX2500/4500 UHF 2. Gentlemen: Motorola Solutions, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Mobile Transmitter environment with capabilities for clear and coded communications with a variable transmit power operating within the following frequency range: 450 - 470 MHz: 1-45 Watts (Nominal) 470 - 520 MHz: 1-45 Watts (Nominal) We are requesting Certification under Part 22, 74, 90, 90.210 and 90.210(e) of the Commission’s Rules to allow operation of this equipment. In addition, this transmitter is intended for work-related occupational use only under Part 90 of the FCC Rules. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793 (Phone). Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Email: [email protected]

FCC ID: AZ492FT4916 Exhibit 13b ___________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. CONFIDENTIALITY REQUEST 4 th July 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ492FT4916 Dear Sir or Madam: Motorola Solutions is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola Solutions considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Please contact me if you require any additional information. Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected]

FCC ID: AZ492FT4916 Exhibit 13c __________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 4 th July 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The APX2500/APX4500 Mobile 2-Way radio was designed to operate in the frequency band 450-520 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola Solutions is requesting that the FCC lists the frequencies 450 - 520 MHz on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB634817 gu idance, as an alternative to listing the exact frequencies, we acknowledge that it’s a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range (MHz) Part 90 Part 22 Part 74 Federal Grant Notes Emission Designator Rule 450-454 x x EF 8K10F1D/F1E/F1W, 11K0F3E 456-460 x x EF “”” 460-462.5375 x EF “”” 462.7375-467.5375 x EF “”” 467.7375-470 x x EF “”” 470-512 x x EF 8K10F1D/F1E/F1W, 11K0F3E, 16K0F3E, 20K0F1E 512-520 x EF “”” Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Email: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 EXTERNAL PHOTOGRAPHS - Pursuant to 47 CFR 2.1033(c) 12 The following photographs are attached. Exhibit 1. Front view (Controls) 3A 2. Back view 3B 3. Top view 3C 4. Bottom View (FCC label location) 3D 5. FCC label (Close view) 3E 6. RF exposure label (Close view) 3F 7. Side view (Left) 3G 8. Side view (Right) 3H 9. Top view with microphone and rear accessory cable 3I Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 2 OF 7 Ex 3A - Front view (Controls) Ex 3B - Back view Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 3 OF 7 Ex 3C - Top view Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 4 OF 7 Ex 3D - Bottom view (FCC Label Location) Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 5 OF 7 Ex 3E - APX4500 FCC label (Close View) Ex 3E - APX2500 FCC label (Close View) Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 6 OF 7 Ex 3F - RF Exposure Label (Close View) Ex 3G - Left view Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 EXHIBIT 3 SHEET 7 OF 7 Ex 3H - Right view Ex 3I - Top view with microphone and rear accessory cable Note: 1. Cables from the connector are wrapped and placed on the radio. 2. RF exposure label placed at the end of the Microphone cable.

Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Exhibit 1 Identification Label LOCATION See the Attached Photograph or Sketch _ Top of Radio _ X Back of Radio Back of Radio under Belt Clip TYPE X The label is a polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with the minimum peel strength of 32 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3D for the actual location of the FCC label on the device. X _ Label Attached Below. See Attached Drawing. FCC Label for APX 4500 Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Exhibit 1 FCC Label for APX 2500

Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Internal Photographs The following photographs are attached. Exhibit 1. RF board with Shields (Top). 9A 2. RF board without Shields (Top). 9B 3. RF board with Shields (Bottom). 9C 4. RF board without Shields (Bottom). 9D 5. Controller board (Top). 9E 6. Controller board with Shields (Bottom). 9F 7. Controller board without Shields (Bottom). 9G 8. RF board with chassis assembly. 9H 9. Controller board with chassis assembly. 9I Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 RF board with Shields (Top) EXHIBIT 9A Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 RF board without Shields (Top) EXHIBIT 9B Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 RF board with Shields (Bottom) EXHIBIT 9C Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 RF board without Shields (Bottom) EXHIBIT 9D Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Controller board (Top) EXHIBIT 9E Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Controller board with Shields (Bottom) EXHIBIT 9F Controller board without Shields (Bottom) EXHIBIT 9G Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 RF board with chassis assembly EXHIBIT 9H Applicant: Motorola Solutions Inc. FCC ID: AZ492FT4916 Controller board with chassis assembly EXHIBIT 9I

FCC ID: AZ492FT4916 SR11154 Form-MPE MC Vehicle rpt. Rev 7.5 Page 1 of 22 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE: MPE ASSESSMENT EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Repor t: 5/24/2013 Repor t Revision: O Repor t ID: SR11154 APX4500 UHF R2 MPE MC rpt Rev O 130524 Responsible Engineer: Michael Sailsman (Sr. Staff EME Engineer) Report author: Michael Sailsman (Sr. Staff EME Engineer) Date(s) Tested: 04/24/13-4/25/13 Manufacturer/Location: Motorola Solutions, Schaumburg, IL Date submitted for test: 03/21/2013 DUT Descr iption: APX4500 UHF R2 15W (450-520 MHz) Motorcycle Mount Option Test TX mode(s): CW M a x. Power out put : 18W TX Frequency Bands: 450 – 520 MHz Signaling type: Analog, APCO 25, and TDMA 1:2 (F2) Model(s) Tested: M22SSS9PW1AN with Motorcycle mount option Model(s) Cer tified: M22SSS9PW1AN with G67 Motorcycle mount option Ser ial Number (s): 471TPF0781 Classification: Occupational/Controlled Environment FCC ID: AZ492FT4916 Part 22 & 90 UHF (450 – 512MHz) Results outside FCC bands are not applicable for FCC compliance demonstration. Based on the infor mation and the testing r esults pr ovided her ein, the under signed cer tifies that when used as stated in the oper ating instr uctions supplied, said pr oduct complies with the national and inter national r efer ence standar ds and guidelines listed in section 3.0 of this r epor t. This r epor t shall not be r epr oduced without wr itten appr oval fr om an officially designated r epr esentative of the Motor ola Solutions Inc. EME Labor ator y. I attest to the accur acy of the data and assume full r esponsibility for the completeness of these measur ements. This reporting format is consistent with the suggested guidelines of the TIA TSB-159 Apr il 2006 The r esults and statements contained in this r epor t per tain only to the device(s) evaluated her ein. Deanna Zakharia EME Lab Senior Resource Manager and Laboratory Director Approval Date: 6/7/2013 Certification Date: 6/7/2013 Cer tification No.: L1130620P FCC ID: AZ492FT4916 SR11154 Form-MPE MC Vehicle rpt. Rev 7.5 Page 2 of 22 Document Revision History Date Revision Comments 05/24/2013 O Initial release FCC ID: AZ492FT4916 SR11154 Form-MPE MC Vehicle rpt. Rev 7.5 Page 3 of 22 Table of Contents 1.0 Introduction ................................................................................................................................. 4 2.0 Abbreviations / Definitions ........................................................................................................... 4 3.0 Referenced Standards and Guidelines............................................................................................ 4 4.0 Power Density Limits ................................................................................................................... 5 5.0 N c Test Channels .......................................................................................................................... 6 6.0 Measurement Equipment .............................................................................................................. 6 7.0 Measurement System Uncertainty Levels ...................................................................................... 6 8.0 Product …

Text truncated - open the document above for the full version.