AZ492FT5850HPD 1000 MOBILE MODEM

HPD MODEM HPD™ 1000 ModemQuick Reference CardProduct Safety and RF Exposure Compliance ATTENTION! This modem is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed wit h your radio (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. BASIC OPERATIONReset ModemChange IP AddressLED INDICATIONS Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. !  Accessory Connector Power Button GPS Connector Ethernet Connector LED Indicators Click this button on the status applet to restart the HPD Modem. 1 Click Change.2 Key in new IP address and click Change once more. Action LED Condition Power OFF - - GPS OFF - - Power ON LED 1 FLASHING GREEN Programming test LED 1 FLASHING AMBER Insufficient voltage/current LED 1 RED Power ON - Self Test failure LED 1- 4 RED Channel - Tx LED 2 FLASHING GREEN Out of range LED 2 & 3 RED Searching for Data Channel LED 2 & 3 FLASHING RED Channel - Rx LED 3 FLASHING GREEN GPS ON LED 4 GREEN GPS ON - Assisted Mode LED 4 AMBER GPS ON - Searching for signal LED 4 FLASHING RED GPS Error/Failure LED 4 RED 96C67_Text.book Page 1 Monday, February 20, 2006 5:19 PM HPD™ 1000 Modemii Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. MOTOROLA, the Stylized M Logo, HPD and FLASHport are registered in the U.S. Patent & Trademark Office. All other product or service names are the property of their respective owners. P25 radios contain technology patented by Digital Voice Systems, Inc. © Motorola, Inc. 2006. All Rights Reserved. Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. !  96C67_Text.book Page ii Monday, February 20, 2006 5:19 PM iii Notations Used in This Manual Throughout the text in this publication, you will notice the use of WARNINGS, CAUTIONS, and Notes. These notations are used to emphasize that safety hazards exist, and care that must be taken or observed. WARNING: An operational procedure, practice, or other condition, which might result in injury or death if not carefully observed. CAUTION: An operational procedure, practice, or other condition, which might result in damage to the equipment if not carefully observed. Note:Note: An operational procedure, practice, or other condition, which is essential to emphasize. WARNING ! CAUTION ! 96C67_Text.book Page iii Monday, February 20, 2006 5:19 PM ASTRO XTL 1500 Digital Mobile Radio with Control Headiv Contents Computer Software Copyrights ......................................................... ii Documentation Copyrights ................................................................ ii Disclaimer ......................................................................................... ii Notations Used in This Manual .........................................................iii Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Software Installation and Setup ........................................................ 2 Important Installation Information for HPD Status Applet ........... 2 HPD Status Applet Installation ................................................... 3 Finishing the installation ............................................................. 4 Status Applet and Features . . . . . . . . . . . . . . . . . . . . . 5 Status Applet Window ....................................................................... 5 Features ..........................................…

Text truncated - open the document above for the full version.

English Product Safety and RF Energy Exposure Booklet for Mobile Two-Way Radios Installed in Vehicles or as Fixed Site Control Stations ATTENTION! The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. © Motorola, Inc. 2005 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 *6881095C99* 68P81095C99-E 2 English RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. This 2-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola 2-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of 2-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 3 English Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile 2-way radios before they can be marketed in the U.S. When 2-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola 2-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standard Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 4 English Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003 • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular, and PCS product certification.” RF Exposure Compliance and Control Guidelines and Operating Instructions To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures. Guidelines: • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Instructions: •Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is 5 English transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX, stop talking. The red LED will extinguish when the radio stops transmitting. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). •Transmit only when people outside the vehicle are at l…

Text truncated - open the document above for the full version.

FCC ID: AZ492FT5860 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. 2 nd March 2006 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ492FT5860, HPD1000. Gentlemen: Motorola Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a Mobile Transmitter environment with capabilities for clear and coded communications with a variable transmit power of 15-42 Watts in the frequency range 764 – 870 MHz (APCO Mode) and 1-12 Watts Average in the frequency range 794-824 MHz (HPD Mode). However, to aid equipment authorization in foreign countries which accept United States FCC Grant for equipment authorization, Motorola is asking the FCC to list on the FCC Grant the following frequencies: 764-870 MHz in APCO Mode. The High Performance Data (HPD) transceiver utilizes two data modes in the 7/800 MHz band. The APCO 25 mode is continuous carrier frequency modulation (C4FM) and HPD or SAM25 mode operates with adjustable 4, 16 and 64QAM. APCO and HPD modes use channel spacing of 12.5 and 25 kHz respectively and supports data transmission rates of 32 kbps, 64 kbps or 96 kbps in half/simplex and Full Duplex operation. There is no voice operation. We are requesting Certification under Part 90 of the Commission’s Rules to allow operation of this equipment. The subject transmitter complies with Section 90.203 of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-5793 Sincerely, /s/ Mike Ramnath (signed) Mike Ramnath Manager, Regulatory Compliance Email: [email protected] FCC ID: AZ492FT5860 ______________________________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. EXHIBIT 13

FCC ID: AZ492FT5850 ______________________________________________________________________________ Motorola Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. CONFIDENTIALITY REQUEST Date: 27 th February 2006 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ492FT5850. Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. We are also requesting that the FCC mark Exhibit 3 (External Photos), 8a and 8b (Users Manual) and Exhibit 9, (Internal Photos) as Temporary or Short-Term Confidentiality as outlined in Public Notice DA 04-1705, dated June 15, 2004. This provision will give Motorola temporary confidentiality prior to product launch. Please mark Exhibits 4, 5, 10, and 12 as “Confidential” and Exhibit 3 (External Photos), 8a and 8b (Users Manual) and 9 (Internal Photos) as “Temporary Confidential”. Please contact me if you require any additional information. Sincerely, /s/ Mike Ramnath (signed) Manager, Regulatory Compliance Tel: (954) 723-5793 E-mail: [email protected] Exhibit 13b

MOTOROLA INC. FCC ID: AZ492FT5850 EXTERNAL PHOTOGRAPHS The following photographs are attached. 1. Front view (Controls) 2. Back view 3. Top view 4. RF exposure label (Close view) 5. Bottom view (FCC label location) 6. FCC label (Close view) 7. Side view (Left) 8. Side view (Right) 9. Bottom view with cables EXHIBIT 3-1 MOTOROLA INC. FCC ID: AZ492FT5850 FRONT VIEW (CONTROLS) EXHIBIT 3-2 MOTOROLA INC. FCC ID: AZ492FT5850 BACK VIEW EXHIBIT 3-3 MOTOROLA INC. FCC ID: AZ492FT5850 TOP VIEW EXHIBIT 3-4 EXHIBIT 3-4 MOTOROLA INC. FCC ID: AZ492FT5850 RF EXPOSURE LABEL (CLOSE VIEW) EXHIBIT 3-5 MOTOROLA INC. FCC ID: AZ492FT5850 BOTTOM VIEW (FCC LABEL LOCATION) EXHIBIT 3-6 MOTOROLA INC. FCC ID: AZ492FT5850 FCC LABEL (CLOSE VIEW) EXHIBIT 3-7 MOTOROLA INC. FCC ID: AZ492FT5850 SIDEVIEW (LEFT) EXHIBIT 3-8 MOTOROLA INC. FCC ID: AZ492FT5850 SIDE VIEW (RIGHT) EXHIBIT 3-9 MOTOROLA INC. FCC ID: AZ492FT5850 BOTTOM VIEW WITH CABLES Note: 1. Cables from the connector are wrapped and placed on the radio. 2. RF exposure label placed at the end of the USB cable. EXHIBIT 3-10

MOTOROLA INC FCC ID: AZ492FT5850 LIST OF EXHIBITS DESCRIPTION EXHIBIT REFERENCE I. Identification label information 1 2.1033-(c) 11 & General Information 1A 1. Production Plans 2.1033-(c) 2. Application References 2.1061 3. Data Submittal Procedure II. Certification of Data 2 III. External Photographs 3 2.1033-(c) 12 IV. Block Diagrams (Circuit Diagrams) 4 V. Schematic Diagrams 5 2.1033-(c)-10 VI. Test Report 6 1. Data Index 6 2. RF Power Output 6A 2.1046 3. Occupied Bandwidth 6B 2.1049 4. Adjacent Channel Coupled Power Ratio 6C 90.543 5. Conducted Spurious Emissions 6D 2.1051 6. Radiated Spurious Emissions 6E 2.1053 7. 1559 – 1610 Radiated Spurious 6F 90.543-(e) 8. Frequency Stability A. Temperature 6G 2.1055 B. Supply Voltage 6H 2.1055 VII. Test Set-up Procedures 7 2.1041 VIII. Instruction Manual 8 2.1033-(c) 3 IX. Internal Photographs. 9 2.1033-(c) 11,12 X. Parts List and Tune-Up procedures 10 2.1033-(c) 9, 10 XI. RF Exposure Information 11 2.1091 XII. Operational Description 12 2.1033-(c) 4, 5 1. Technical Characteristics 2. Application XIII. Cover Letter 13 MOTOROLA INC FCC ID: AZ492FT5850 IDENTIFICATION LABEL LOCATION See the Attached Photograph or Sketch X Back Of Radio Back Of Radio under Belt Clip TYPE X The label is a polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 32 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3-5 for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. EXHIBIT 1 MOTOROLA INC FCC ID: AZ492FT5850 GENERAL INFORMATION I. Production Plans -- Pursuant 2.1033 (c) Quantity production is planned. II. Application References -- Pursuant 2.1061 Reference is made to the following Motorola "Application References" 1. Mobile Products and their application. 2. Mobile Products Transmitter Modulations Methods. 3. Plantation, Florida Antenna Range. III. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ rules. Necessary Bandwidth Computation for 17K7D7D and 8K10F1E Emission Designators The FCC Rule & Regulations Part 2, §2.202(b) defines Necessary Bandwidth as the minimum value of the occupied bandwidth sufficient to ensure that transmission of information at the rate and with the quality required for the system employed. §2.202(c) lists four methods of determining the necessary bandwidth, including the use of formulas in §2.202(g), and measurement in cases where the other methods of §2.202(c) do not apply. It is felt that while these formulas apply well to voice and many older digital modulation systems, the formulas do not apply to the high performance digital modulation employed in the system submitted for Certification because of difficulties determining representative values for the factors K and M. We have, therefore, used the measurement criteria of §2.202(c) (4). The value cited, 17K7 and 8K10, is the bandwidth that contains 99% of the total transmitted power. The 99% value was chosen because §2.202(b) defines Necessary Bandwidth as the minimum value of the occupied bandwidth. In turn, §2.202(a) defines Occupied Bandwidth as the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5% of the total mean power radiated by a given emission, i.e., contains 99% of the total transmitted power. IV. Applicable References: • Reference Certification FCC ID: ABZ89FC5810 and ABZ89FC5812 • TIA-102.CAAA Digital C4FM/CQPSK Transceiver Measurement Methods • TIA/EIA-102.CAAB Land Mobile Radio Transceiver Recommendations, Project 25 – Digital Radio Technology, C4FM/ CQPSK Modulation • EIA/TIA-603A Land Mobile FM or PM Communications Equipment Measurement and Performance Standards • FCC Federal Regulations Part 47 Sec. 2.1033 – 2.1055 • FCC Federal Regulations Part 90 Sec.90.210, 90.539 and 90.543 EXHIBIT 1A

MOTOROLA INC. FCC ID: AZ492FT5850 INTERNAL PHOTOGRAPHS The following photographs are attached. 1. Transmitter board (Top view) 2. Transmitter board (bottom view) 3. Transceiver board (Top view) 4. Transceiver board (Bottom view) 5. Transmitter board, less shields (Top view) 6. Transmitter board, less shield (bottom view) 7. Transceiver board, less shield (Top view) 8. Transceiver board, less shield (Bottom view) EXHIBIT 9-1 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSMITTER BOARD (TOP VIEW) EXHIBIT 9-2 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSMITTER BOARD (BOTTOM VIEW) EXHIBIT 9-3 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSCEIVER BOARD (TOP VIEW) EXHIBIT 9-4 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSCEIVER BOARD (BOTTOM VIEW) EXHIBIT 9-5 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSMITTER BOARD, LESS SHIELD (TOP VIEW) EXHIBIT 9-6 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSMITER BOARD, LESS SHIELD (BOTTOM VIEW) EXHIBIT 9-7 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSCEIVER BOARD, LESS SHIELD (TOP VIEW) EXHIBIT 9-8 MOTOROLA INC. FCC ID: AZ492FT5850 TRANSCEIVER BOARD, LESS SHIELD (BOTTOM VIEW) EXHIBIT 9-9

FCC ID: AZ492FT5850 SR3393 Form-MPE Vehicle rpt. Rev 3.00 Page 1 of 20 Certificate Number: 1449-01 FCC ID: AZ492FT5850 DECLARATION OF COMPLIANCE MPE ASSESSMENT Government & Enterprise Mobility Solutions EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: February 24, 2006 Report Revision: Rev. O Report ID: FCC MPE rpt_HPD1000 7/800 Rev O_060224_SR3393 Responsible Engineer: Stephen Whalen (SR Staff EME Eng.) Date/s Tested: 2/18/2006 Manufacturer/Location: Motorola / Plantation Date submitted for test: 01/13/2006 DUT Description: High Performance Data in 25 kHz Channel in 7/800MHz, APCO 764-806MHz 33W, 806-870MHz 38.5W mode, HPD 794-824MHz nominal 10W pulse average. Test TX mode(s): APCO mode CW, HPD mode 70% duty cycle Max. Power output: APCO 764-806MHz 36W, 806-870MHz 42W, 50% Duty Cycle HPD 794-824MHz maximum 12W pulse average, 70% Duty Cycle TX Frequency Bands: APCO 764-776MHz, 794-824MHz, 851-870MHz HPD 794-824MHz Signaling type: FM, APCO 25, HPD (SAM 25) Model(s) Tested: M26UGA9PW1AN Model(s) Certified: M26UGA9PW1AN Serial Number(s): P7F5 Classification: Occupational Controlled (Operator); General Population/Uncontrolled (Passengers/Bystanders) Rule Part(s): 2.1091 (d) Approved Accessories: Antenna(s): HAF4016A (764-870MHz ¼ wave roof mount antenna; 0dBd gain), HAF4014A (764-870MHz ¼ wave roof mount antenna; 3.0dBd gain) HAF4013A (764-870MHz ¼ wave roof mount antenna; 3.0dBd gain), HAF4017A (764-870MHz ¼ wave roof mount antenna; 3.0dBd gain) RRA4914B (806-900MHz ¼ wave roof mount antenna; 3.0dBd gain), HAF4002A (806-900MHz ¼ wave roof mount antenna; 0.0dBd gain) Final RF Exposure Results: Max Calculated Power Density: 0.14mW/cm^2 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. Signature on file Ken Enger GEMS EME Lab Senior Resource Manager, Laboratory Director, Approval Date: 2/24/2006 Certification Date: L1060289 Certification No.: 2/24/2006 FCC ID: AZ492FT5850 SR3393 Form-MPE Vehicle rpt. Rev 3.00 Page 2 of 20 TABLE OF CONTENTS 1.0 Product and System Description 2.0 Additional Options and Accessories 3.0 Measurement and Limit Standards 4.0 Data Collection Consideration 5.0 Measurement System Uncertainty Levels 6.0 Method of Measurement 6.1 EME measurements made with roof mounted antenna(s) 6.1.1 External vehicle EME measurement 6.1.2 Internal vehicle EME measurement 7.0 Test Site 8.0 Measurement System/Equipment 9.0 Test Unit Description 10.0 Test Set-Up Description 11.0 Test Results Summary 12.0 Conclusion APPENDIX A: Illustration of Antenna Location and Test Distance APPENDIX B: Meter/Probe Calibration Certificates APPENDIX C: Photos of Assessed Antennas APPENDIX D: Detailed MPE Measurement Data REVISION HISTORY Date Revision Comments 02/24/06 O Original release FCC ID: AZ492FT5850 SR3393 Form-MPE Vehicle rpt. Rev 3.00 Page 3 of 20 1.0 Product and System Description FCC ID: AZ492FT5850, model M26UGA9PW1AN is a High Performance Data (HPD) transceiver that utilizes two data modes in the 7/800MHz band. The APCO 25 mode is continuous carrier frequency modulation (C4FM) and HPD or SAM25 mode operates with adjustable 4, 16 and 64QAM. Both the APCO and HPD modes use channel spacing of 12.5 and 25kHz and supports data transmission rates of 32 kbps, 64 kbps or 96 kbps in Half/ simplex and Full Duplex operation. There is no voice operation. The maximum duty cycle is 50% for APCO which is based on simplex hand-shaking operation between the user and base station. The maximum duty cycle is 70% for HPD which is controlled by the software. Two antennas are used, one for transmit and one for receive with the device properly installed in a vehicle trunk. The transmit antenna is to be mounted on the center of the roof with the receive antenna at a specified distance from the transmit antenna and typically installed on the trunk. The APCO mode transmits in 764-776MHz and 794-806MHz at 33W nominal power and 806- 824MHz and 851-870MHz at 38.5W nominal power. The HPD transmits in 794-824MHz at nominal 10 Watts pulse average power. This device will be marketed to and used by employees solely for work-related operations, such as public safety agencies, e.g. police, fire and emergency medical. User training is the responsibility of these agencies which can be expected to employ the usage instructions, safety information and operational cautions set forth in the user's manual, instructional sessions or other means. Accordingly this product is classified as Occupational/Controlled Exposure. However, In accordance with FCC requirements, the passengers inside the vehicle and the bystanders external to the vehicle are evaluated to the General Population/Uncontrolled Exposure Limits. (Note that “By-standers” as used herein mean people other than operator) 2.0 Additional Options and Accessories: NA 3.0 Measurement and Limit Standards Measurements were performed according to the recommended guidelines in IEEE/ANSI C95.3-2002 and compared to FCC Limits Per 47 CFR 2.1091 (d) for General Population/Uncontrolled RF Exposure. For test frequencies ranging from 764-870MHz the MPE (Maximum Permissible Exposure) limit to electromagnetic energy in equivalent plane wave free-space power density is 0.51 – 0.58mW/cm 2 and calculated using the formula f/1500. FCC ID: AZ492FT5850 SR3393 Form-MPE Vehicle rpt. Rev 3.00 Page 4 of 20 4.0 Data Collection Consideration Power density testing was performed with DUT installed in a 1991 Ford Taurus (4-door). Measurement data was taken with the vehicle running at idle and the vehicle battery measuring 14.0 volts. 5.0 Measurement System Uncertainty Levels The information below presen…

Text truncated - open the document above for the full version.

MOTOROLA INC. FCC ID: AZ492FT5850 SUBMITTED MEASURED DATA MEASUREMENT EXHIBIT NUMBER OF PAGES I RF Power Output 6A 1 II Occupied Bandwidth 6B 6 III Adjacent Channel Coupled 6C 2 Power Ratio IV Conducted Spurious 6D 14 Emissions V Radiated Spurious 6E 14 Emissions VI 1559-1610 Radiated Spurious 6F 2 VII Frequency Stability A. Temperature 6G 2 B. Supply Voltage 6H 1 EXHIBIT 6 MOTOROLA INC. FCC ID: AZ492FT5850 RF POWER OUTPUT The primary radio input supply voltage is 13.6 V for both Compatible 4-Level Frequency Modulation (C4FM) and High Performance Data (HPD) modes. The RF power output was measured with the indicated voltage applied to and current into the driver and final RF amplifying device. HPD 64-QAM Mode: Frequency (MHz) RF Output Power (W) Nominal DC Voltage (Volts) Nominal DC Current (Amps) 794.0875 1 28 1.42 12 28 2.93 809.9875 1 28 1.39 12 28 2.93 823.9875 1 28 1.42 12 28 2.93 C4FM Mode: Frequency (MHz) RF Output Power (W) Nominal DC Voltage (Volts) Nominal DC Current (Amps) 764.0875 15 23 3.28 36 23 5.08 823.9875 15 23 3.01 42 23 5.23 868.9875 15 23 2.86 42 23 5.91 EXHIBIT 6A MOTOROLA INC. FCC ID: AZ492FT5850 OCCUPIED BANDWIDTH BANDWIDTH CALCULATIONS: Shown below are the calculations required for FCC ID: AZ492FT5850 EXHIBITS 6E-1, 6E-2 & 6E-3 High Performance Data Mode (25 kHz Channelization, Digital Data): Emission Designator 17K7D7D These exhibits show occupied bandwidth data for different modulation schemes (QPSK, 16-QAM and 64-QAM) used in high performance data mode. All these modulation schemes can be used in a system configuration based upon channel usage as described Exhibit 4. The necessary bandwidth of the modulation signal is not calculable per the formula defined in 47 CFR 2.202(g) and so measurements were done per Rule Part 2.202 Section C(4). Therefore, the 99% energy rule, per 2.202(a), was used for digital mode and is more accurate than Carson’s rule. It basically states that 99% of the modulation energy falls within X KHz, in this case, 17.7 kHz. Measurements were performed in accordance with TIA/EIA 102.CAAB Section 2.2.5.2. The emission mask was obtained from 47CFR 90.210(g). …

Text truncated - open the document above for the full version.