AZ492FT6012Mobile Microphone with Bluetooth Gateway

LONG RANGEWIRELESS SOLUTIONSUSER GUIDE ACCESSORIES WIRELESS REMOTE SPEAKER MICROPHONE PMMN4095_MOBILE MICROPHONE WITH BLUETOOTH GATEWAY PMMN4097_DUAL-UNIT CHARGER PMLN6714_VEHICULAR CHARGER PMLN6716_WIRELESS REMOTE SPEAKER MICROPHONE BATTERY PMNN4461_ en es-CO pt-BR fr-CA ko de-DE fr-FR es-ES it-IT pt-PT nl-NL ru FOREWORD English i CHAPTER 1: FOREWORDRF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios ATTENTION! The microphone is restricted to occupational use only to satisfy ICNIRP/FCC RF energy exposure requirements. Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Motorola may void the user’s authority to operate this device.Under Industry Canada regulations, this microphone transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Ca nada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Battery Information : Battery is shipped with a nominal charge between 30% and 50%. Battery should be stored between -10 °C (14 °F) and 30 °C (86 °F) to minimize permanent capacity loss.CAUTION : Storing your fully charged accessory in high-temperature conditions may permanently reduce the life of the internal battery. Important Information: • Hold the microphone in a vertical position with the microphone at  least  inch (2.5 centimeters) away from the nose or lips. • Body Worn Operation. When microphone is worn on the body, always use Motorola-approved clip for this product. Using approved body-worn accessories is important because the use of non-Motorola-approved accessories may result in exposure levels, which exceedthe FCC occupational/controlled environment RF exposure limits. • Use only Motorola-approved supplied or replacement batteries. Useof non-Motorola-approved batteries may exceed the applicable RFexposure guidelines (iEEE, ICNIRP or FCC). • DO NOT charge your accessory in temperatures below 0 °C (32 °F)or above 45 °C (113 °F). DO NOT store your accessory in directsunlight or where expected temperatures can exceed this range such as inside a parked car. • Storing your fully charged accessory in high-temperature conditionsmay permanently reduce the life of the internal battery. • Battery life may temporarily shorten in low-temperature conditions. FOREWORD English ii Acoustic SafetyExposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.To protect your hearing:• Use the lowest volume necessary to do your job. • Turn up the volume only if you are in noisy surroundings. • Turn down the volume before adding headset or earpiece. • Limit the amount of time you use headsets or earpieces at high volume. • When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear. CHARGERS SAFETY INFORMATIONImportant Safety InformationThis document contains important safety and operating instructions. Please read these instructions carefully and save them for future reference.Before using the battery charger, read all the instructions and cautionary markings on (1) the Dual-Unit Charger / Vehicular Charger, (2) the battery, and (3) on the Wireless Remote Speaker Microphone (WRSM). WARNINGS ! W A R N I N G ! 2. Use of accessories not recommended by Motorola may result in risk of fire, electric shock, or injury. 3. To reduce risk of damage to the electric plug and cord of the DUC, pull by the plug rather than the cord when disconnecting the charger. 4. To reduce risk of damage to the CLA and cord of the Vehicular Charger, pull by the CLA rather than the cord when disconnecting the charger. 5. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18 AWG for lengths of up to 100 feet (30.48 m), and 16 AWG for lengths up to 150 feet (45.72 m). 6. To reduce risk of fire, electric shock, or injury, DO NOT operate the charger if it has been broken or damaged in any way. Take it to a qualified Motorola service representative. 7. DO NOT disassemble the charger – it is not repairable and replacement parts are not available. Disassembly of the charger may result in risk of electric shock or fire. 8. To reduce risk of electric shock of the DUC, unplug the charger from the AC outlet before attempting any maintenance or cleaning. 9. To reduce risk of electric shock of the Vehicular Charger, unplug the Vehicular Charger from the CLA power source before attempting any maintenance or cleaning. 10. This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 1. To reduce risk of injury, charge only the rechargeable Motoro…

Text truncated - open the document above for the full version.

FCC ID: AZ492FT6012 Motorola Solutions Inc. Exhibit 13a 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 June 6, 2014 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: AZ492FT6012 Dear Sir or Madam, Motorola Solutions Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida, herein submits application for Certification of the subject transmitter. This transmitter, Mobile Microphone with Bluetooth Gateway , is primarily intended for use in a Class 1 Bluetooth application. This Bluetooth transmitter is capable of clear communication with fixed power operating within the following frequency ranges: Frequency Range RF Power 2402-2480 MHz 50 mW Rated; 63 mW Max 125 kHz 0.1 mW The Bluetooth transmitter complies with the requirements of FCC Part 15 subpart C. A complete certification application is enclosed. Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Motorola Solutions Inc. 8000 West Sunrise Blvd. Fort Lauderdale, FL33322 Tel: (954) 723-5422 E-mail: [email protected]

FCC ID: AZ492FT6012 Motorola Solutions Inc. Exhibit 13b 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 CONFIDENTIALITY REQUESTED Date: June 6, 2014 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request Regarding Application for Transmitter with FCC ID: AZ492FT6012 Dear Sir or Madam: Motorola Solutions Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) is requesting for the following Exhibits be held as Permanently Confidential, and not be made routinely available for public inspection: Exhibit 4 Block diagrams Exhibit 5 Schematic Diagrams Exhibit 10 Parts List Exhibit 12 Circuit Descriptions Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Sections 0.457(d), 0.459 and 552(b)(4) of the Freedom of Information Act. Please mark these Exhibits as “Confidential.” Please contact me if you require any additional information. Sincerely, Kim Uong Regulatory Compliance Engineer Motorola Solutions Inc. 8000 West Sunrise Blvd Fort Lauderdale, FL33322 Tel: (954) 723-5422 E-mail: [email protected]

Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 1 OF 8 EXHIBIT 3 The following photographs are attached. Exhibit 1. Front Overview 3A 2. Back Overview 3B 3. Front View 3C 4. Back View 3D 5. Side view (Right). 3E 6. Side view (Left). 3F 7. Top view. 3G 8. Bottom view 3H Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 2 OF 8 Exhibit 3A Front Overview Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 3 OF 8 Exhibit 3B Back Overview Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 4 OF 8 Exhibit 3C FRONT VIEW Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 5 OF 8 Exhibit 3D BACK VIEW Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 6 OF 8 Exhibit 3E SIDE VIEW (RIGHT) Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 7 OF 8 Exhibit 3F SIDE VIEW (LEFT) Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 3 SHEET 8 OF 8 Exhibit 3G TOP VIEW Exhibit 3H BOTTOM VIEW

Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 1 SHEET 1 OF 1 IDENTIFICATION LABEL LOCATION See the Attached Photograph or Sketch Top of Radio X Back of Radio Back of Radio under Belt Clip TYPE __ X The label is made of polycarbonate material with Nitto adhesive backing. The adhesive is with pull strength of 15 N/20mm. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. X_ Label Attached Below. See Attached Drawing. FIGURE 1: FCC LABEL FOR SALES MODEL PMMN4097A FIGURE 2: COO (Country of Origin) LABEL FOR SALES MODEL PMMN4097A

Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 9 SHEET 1 OF 4 EXHIBIT 9 INTERNAL PHOTOGRAPHS The following photographs are attached. Exhibit 1. Overall Internal Assembly 9A 2. PCB Bottom 9B 3. PCB Top 9C 4. PCB Top without Shield 9D 5. PCB Bottom without Shield 9E Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 9 SHEET 2 OF 4 Exhibits 9A Overall Internal Assembly Exhibit 9B PCB Bottom Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 9 SHEET 3 OF 4 Exhibit 9C PCB Top Exhibit 9D PCB Top without Shield Motorola Solutions Inc FCC ID: AZ492FT6012 / IC: 109U-92FT6012 EXHIBIT 9 SHEET 4 OF 4 Exhibit 9E PCB Bottom without Shield

FCC ID: AZ492FT6012 / IC: 109U-92FT6012 SR12080 TESTING CERT # 2518.01 DECLARATION OF COMPLIANCE SAR ASSESSMENT Motorola Solutions Inc. EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 Date of Report: 06/05/2014 Report Revision: A Responsible Engineer: Stephen C. Whalen (Principal Staff Engineer/Manager) Report Author: Stephen C. Whalen (Principal Staff Engineer/Manager) Date/s Tested: 05/05/2014 Manufacturer/Location: Motorola Solutions Inc., TEMCO , Japan Sector/Group/Div.: Radio Product & Accessories (RPA), Business Light Date submitted for test: 02/12/2014 DUT Description: Handheld Speaker Microphone – Frequency bands; Bluetooth 2.402-2.480GHz Test TX mode(s): CW Max. Power output: 18dBm (63mW) Nominal Power: 17dBm (50mW) Tx Frequency Bands: Bluetooth 2.402-2.480GHz Signaling type: FHSS (Bluetooth) Model(s) Tested: PMMN4097A Model(s) Certified: PMMN4097A Serial Number(s): ACS#1 Classification: Occupational/Controlled FCC ID: AZ492FT6012; Rule Part 15 (2.402-2.480GHz) IC: 109U-92FT6012 The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of OET Bulletin 65. The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 4.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 6/05/2014 Certification Date: 6/05/2014 Certification No.: L1140605P Motorola Solutions Inc. EME Form-SAR-Rpt-Rev. 13.7 Page 1 of 47 FCC ID: AZ492FT6012 / IC: 109U-92FT6012 SR12080 1.0 Introduction ................................................................................................................................. 4 2.0 FCC SAR Summary .................................................................................................................... 4 3.0 Abbreviations / Definitions ......................................................................................................... 4 4.0 Referenced Standards and Guidelines ........................................................................................ 4 5.0 SAR Limits ................................................................................................................................. 5 6.0 Description of Device Under Test (DUT) .................................................................................. 6 7.0 Accessories and Test Criteria...................................................................................................... 6 7.1 Antenna ........................................................................................................................... 6 7.2 Battery ............................................................................................................................. 6 7.3 Body worn Accessory ..................................................................................................... 6 8.0 Description of Test System ......................................................................................................... 6 8.1 Descriptions of Robotics/Probes/Readout Electronics ................................................... 7 8.2 Description of Phantom(s) .............................................................................................. 7 8.3 Description of Simulated Tissue ..................................................................................... 7 9.0 Additional Test Equipment ......................................................................................................... 8 10.0 SAR Measurement System Validation and Verification ............................................................ 9 10.1 System Validation ........................................................................................................... 9 10.2 System Verification ........................................................................................................ 9 10.3 Equivalent Tissue Test Results ....................................................................................... 9 11.0 Environmental Test Conditions ................................................................................................ 10 12.0 DUT Test Setup and Methodology ........................................................................................... 10 12.1 Measurements ............................................................................................................... 10 12.2 DUT Configuration(s) ................................................................................................... 11 12.3 DUT Positioning Procedures ........................................................................................ 11 12.3.1 Body ............................................................................................................... 11 12.3.2 Head ............................................................................................................... 11 12.3.3 Face ...........…

Text truncated - open the document above for the full version.

Certification Test Report FCC ID: AZ492FT6012 IC: 109U-92FT6012 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 13-2171.W06.1A Applicant: Motorola Solutions SDNBHD Model: PMMN4097A Test Begin Date: April 4, 2014 Test End Date: April 14, 2014 Report Issue Date: April 17, 2014 FOR THE SCOPE OF ACCREDITATION UNDER CERTIFICATE NUMBER AT-1533 This report must not be used by the client to claim product certification, approval, or endorsement by ACLASS, ANSI, or any agency of the Federal Government. Project Manager: Reviewed by: Thierry Jean-Charles Kirby Munroe EMC Engineer Director, Wireless Certifications Advanced Compliance Solutions, Inc. Advanced Compliance Solutions, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 37 pages 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 TABLE OF CONTENTS 1 GENERAL ...................................................................................................... 3 1.1 Purpose .............................................................................................................................................. 3 1.2 Product Description .......................................................................................................................... 3 1.3 Manufacturer Information .............................................................................................................. 3 1.4 Test Methodology and Considerations ........................................................................................... 4 2 TEST FACILITIES .......................................................................................... 5 2.1 Location ............................................................................................................................................. 5 2.2 Laboratory Accreditations/Recognitions/Certifications ............................................................... 5 2.3 Radiated & Conducted Emissions Test Site Description .............................................................. 6 3 APPLICABLE STANDARD REFERENCES................................................... 8 4 LIST OF TEST EQUIPMENT .......................................................................... 9 5 SUPPORT EQUIPMENT .............................................................................. 10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ............................ 11 7 SUMMARY OF TESTS ................................................................................. 12 7.1 Antenna Requirement – FCC: Section 15.203 ..............................................................................12 7.2 Peak Output Power - FCC Section 15.247(b)(1) IC: RSS-210 A8.4(2) .......................................12 7.3 Channel Usage Requirements .........................................................................................................15 7.4 Band-Edge Compliance and Spurious Emissions-FCC 15.247(d) IC: RSS-210 A8.5 ................24 8 CONCLUSION .............................................................................................. 36 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210. 1.2 Product Description The Motorola Solutions Model PMMN4097A is a mobile microphone for TX audio only with Bluetooth Gateway incorporated for Bluetooth pairing with Wireless RSM and Wireless Pod. Per the applicant, the equipment only supports the GFSK modulation for the 2.4 GHz Bluetooth radio. The equipment also incorporates a 125 kHz radio for near field communications. Table1.3-1: Bluetooth Radio Properties Mode of Operation Frequency Range (MHz) Number of Channels Channel Separation (kHz) Data Rates Supported (kbps) GFSK 2402 - 2480 79 1000 1000 1.3 Manufacturer Information Applicant Motorola Solutions Malaysia Sdn Bhd Plot 2, Bayan Lepas, Technoplex Industrial Park, Mukim 12, SWD (CSC) 11900 Bayan Lepas, Penang Malaysia Manufacturer Temco 2-21-4 Honan, Suginamu-Ku Tokyo 168-062 Japan Model Number: PMMN4097A Test Sample Serial Number(s): ACS#1 (Radiated), ACS#2 (RF Conducted), Test Sample Condition: The samples were in good conditions with no observable physical damages. ACS Report: 13-2171.W06.1A Advanced Compliance Solutions Page 3 of 37 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 1.4 Test Methodology and Considerations The EUT was evaluated for RF conducted, radiated emissions for the 2.4 GHz Bluetooth transceiver. The EUT is only installed in vehicles and is exempted from the power line conducted emissions requirements. The RF conducted measurements were performed with the EUT configured with a temporary SMA connector at the RF port. The radiated emissions evaluation was performed with the EUT powered through a mobile radio. The emissions were investigated up to the 10 th harmonic of the fundamental frequency, with the EUT set in 3 orthogonal orientations. The final measurements were performed with the EUT set vertically, which led o the highest emissions as compared to the limits. The EUT was also evaluated for intermodulation product for the co-located Bluetooth and 125 kHz transceivers transmitting at the same time. All intermodulation products were found to be compliant the limits of FCC Section 15.209 and RSS-Gen. The Bluetooth radio was configured using the CSR BlueTest3 Software. The test power settings were selected as listed below. GFSK: Power (1, 42) The frequencies and data rates used during the evaluation are provided below. Table 1.4-1: Bluetooth Radio Test configuration Mode of Operations Frequency (MHz) Data Rate (kbps…

Text truncated - open the document above for the full version.

Certification Exhibit FCC ID: AZ492FT6012 IC: 109U-92FT6012 FCC Rule Part: 15.209, 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 13-2171 Applicant: Motorola Solutions SDNBHD Model: PMMN4097A Test Setup Photos 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 1: Radiated Emissions – Front View (Below 1 GHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 2 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 2: Radiated Emissions – Back View (Below 30 MHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 3 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 3: Radiated Emissions – Back View (30 MHz – 200 MHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 4 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 4: Radiated Emissions – Back View (200 MHz – 1GHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 5 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 5: Radiated Emissions – Front View (Above 1 GHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 6 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 6: Radiated Emissions – Back View (Above 1 GHz) ACS Project: 13-2171 Advanced Compliance Solutions Page 7 Model: PMMN4097A FCC ID: AZ492FT6012 IC: 109U-92FT6012 Figure 7: RF Conducted Emissions ACS Project: 13-2171 Advanced Compliance Solutions Page 8