AZD241Wireless module

FCC/IC NOTICE This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter except Canon accessories supplied or designated for this product. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This model has been tested and found to comply with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. 5.15-5.35GHz band is restricted to indoor operations only. Frequency Tolerance:20 ppm Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. FCC ID:AZD241 FCC/IC Notice for model: ES204 Following statement must be included in the user manual of host device. The end product must be labeled “Contains FCC ID: AZD241” and “IC: 498J-241” We don't prepare the User Manual for the module because it is not sold to the end user directly. Please refer to the Specification Sheet for more details about the module. For the module installation to the host equipment, please follow the interface specification (installation procedure). 【 Other items to be entered 】 Information from the local representatives 【 Applicable FCC rules 】 FCCPart15SubpartC FCCPart15SubpartE

䕔 Photo surface reverse 䕔 AntennaSize 20.0 䟚 5.0 䟚 L=10 䠉 200 䟚 Applying device Antenna connector 9.8 䟚 7.9 䟚

ＥＳ204 ■ Labeldesign It cannot be listed on the modulebecause the module size is too small, so it should be listed in the manual and box of the module(ES204) as below. Manual ES204(FCC ID:AZD241) Box ES204 (FCC ID:AZD241)

Confidential ES204/Type1SM Parts Layout (Internal) 20 th December 2019 Top Bottom No parts on Bottom Copyright © Murata Manufacturing Co., Ltd. All rights reserved.

Test report No. : 13024973S-A-R3 Page : 1 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 CERTIFICATE 1266.03 SAR TEST REPORT Test Report No.: 13024973S-A-R3 Applicant : Canon Inc. Type of Equipment : Wireless LAN/Bluetooth Combo Module Model No. : ES204 (*. Installed into the platform (1)) FCC ID : AZD241 Test Standard : FCC 47CFR §2.1093 Test Result : Complied (Refer to Section 3.5) Highest Reported SAR(1g) [W/kg] Platform Remarks (DTS band) Remarks (UNII band) Reference report number DTS band U-NII band SAR type SAR Limit No. Type Model Frequency [MHz] Mode Output power (average) [dBm] Frequency [MHz] Mode Output power (average) [dBm] Measured Max. Measured Max 0.25 0.42 Body-worn 1.6 1 Digital Camera DS126836 2462 b 8.36 10.0 5180 a 8.79 10.0 This report. *. Highest reported SAR (1g) across all exposure conditions for body-touch is "0.25 W/kg (DTS)” and "0.42 W/kg (U-NII)”. *. Highest reported SAR (1g) values for simultaneous transmission (Bluetooth + Wi-Fi (5GHz band)) is "0.50 W/kg (< 1.6 W/kg)”. *. Since highest reported SAR (1g) on all platforms of model: ES204 (EUT) which obtained in accordance with KDB447498 (v06) was kept under 0.8 W/kg, this EUT was approved to operate multi-platform (which was tested in above.). *. Max.:Maximum, (Mode) b: IEEE 802.11b, a: IEEE 802.11a. 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2 . The results in this report apply only to the sample tested. 3 . This sample tested is in compliance with the limits of the above regulation. 4 . The test results in this test report are traceable to the national or international standards. 5 . This test report must not be used by the customer to claim product certification, approval, or endorsement by any agency of the Federal Government. 6. This test report covers Radio technical r equirements. It does not cover administrative issues such as Manual or non-Radio test related Requirements. (if applicable) 7. The al l test items in this test report are conducted by UL Japan, Inc. Shonan EMC Lab. 8. The o pinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. 9. The information provided from the customer for this report is identified in SECTION 1. 1 0. This report (-R3) is a revised version of 13024973S-A-R2. 13024973S-A, 13024973S-A-R1, 13024973S-A-R2 reports are replaced with this report. Date of test: November 11, 12 and 19, 2019 Test engineer: Hiroshi Naka Engineer, Consumer Technology Division Approved by: Toyokazu Imamura Leader, Consumer Technology Division The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". (Revision Date:2019/6/24) Test report No. : 13024973S-A-R3 Page : 2 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 REVISION HISTORY Revision Test report No. Date Page revised Contents Original 13006525S-A December 10, 2019 - - -R1 13006525S-A-R1 December 18, 2019 - (p2, REVISION HISTORY, Corrected issue date) was: December xx, 201 9->R1: December 10, 2019 -R2 13024973S-A-R2 March 30, 2020 P1, 2, 4 p1&2; add revised (-R2) information, p4; (clause 2.1) “Rating” was changed. (was: DC 9.0 V -> R2: DC 9.0 V/5.0 V) p4; (clause 2.2) Add comment: “ *1. The frequency band of U-NII-2C is (5500~5700) MHz. The EUT is not su pported the frequency band of (5600~5650) MHz on this platform by the firmware.” -R3 13024973S-A-R3 April 2, 2020 P1, 2, 7 p1&2; add revised (-R2) information, p7; (clause 3.5) Corrected a mistake (asterisk number). (was: 0.417 (*2) -> R3: 0.417 (*1)) *. By issue of new revision report, the report of an old revision becomes invalid. Reference: Abbreviations (Including words undescribed in this report) (radio_r0v02_191128) A2LA The American Association for Laboratory Accreditation IF Intermediate Frequency AC Alternating Current ILAC International Laboratory Accreditation Conference AFH Adaptive Frequency Hopping ISED Innovation, Science and Economic Development Canada AM Amplitude Modulation ISO International Organization for Standardization Amp, AMP Amplifier JAB Japan Accreditation Board ANSI American National Standards Institute LAN Local Area Network Ant, ANT Antenna LIMS Laboratory Information Management System AP Access Point MCS Modulation and Coding Scheme ASK Amplitude Shift Keying MRA Mutual Recognition Arrangement Atten., ATT Attenuator N/A Not Applicable AV Average NIST National Institute of Standards and Technology BPSK Binary Phase-Shift Keying NS No signal detect. BR Bluetooth Basic Rate NSA Normalized Site Attenuation BT Bluetooth NVLAP National Voluntary Laboratory Accreditation Program BT LE Bluetooth Low Energy OBW Occupied Band Width BW BandWidth OFDM Orthogonal Frequency Division Multiplexing Cal Int Calibration Interval P/M Power meter CCK Complementary Code Keying PCB Printed Circuit Board Ch., CH Channel PER Packet Error Rate CISPR Comite International Special des Perturbations Radioelectriques PHY Physical Layer CW Continuous Wave PK Peak DBPSK Differential BPSK PN Pseudo random Noise DC Direct Current PRBS Pseudo-Random Bit Sequence D-factor Distance factor PSD Power Spectral Density DFS Dynamic Frequency Selection QAM Quadrature Amplitude Modulation DQPSK Differential QPSK QP Quasi-Peak DSSS Direct Sequence Spread Spectrum QPSK Quadrature Phase Shift Keying EDR Enhanced Data Rate RBW Resolution Band Width EIRP, e.i.r.p. Equivalent Isotropically Radiated Power RDS Radio Data System EMC ElectroMagnetic Compatibility RE Radio Equipment EMI El…

Text truncated - open the document above for the full version.

Test report No. : 13024973S-A-R3 Page : 24 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 APPENDIX 2: SAR Measurement data SAR plot of worst reported SAR Plot 1-1: Front-upper, 11b(1Mbps), 2462 MHz->Higher reported SAR(1g), 2.4GHz band EUT: Wireless LAN/Bluetooth combo module in Digital camera; Type: ES204(camera:DS126836); Serial: DE1-C-012(camera:3) Mode: 11b(1Mbps, DBPSK/DSSS) (UID: 0, Wi-fi_5GHz (0), Frame Length in ms: 0; PAR: 0; PMF: 1); Frequency: 2462 MHz; Crest Factor: 1.0 Medium: M2450(1911); Medium parameters used: f = 2462 MHz; σ = 2.001 S/m; ε r = 50.51; ρ = 1000 kg/m 3 Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY Configuration: -Electronics: DAE4 Sn626; Calibrated: 2019/10/15 / -Phantom: ELI v4.0; Type: QDOVA001BA; Serial: 1059; Phantom section: Flat Section -DASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) /-Probe: EX3DV4 - SN3907; ConvF(7.37, 7.37, 7.37) @ 2462 MHz; Calibrated: 2019/06/19 -Sensor-Surface: 2mm (Mechanical Surface Detection (Locations From Previous Scan Used)), Sensor-Surface: 2mm (Mechanical Surface Detection), z = 1.0, 31.0, 161.0 body,touch,near-ant/b12;2462,front-top3&d0,b(1m,max10)/ Area:108x72,12 (10x7x1): Measurement grid: dx=12mm, dy=12mm; Maximum value of SAR (measured) = 0.277 W/kg Area:108x72,12 (91x61x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm; Maximum value of SAR (interpolated) = 0.280 W/kg Z;160,5 (1x1x33): Measurement grid: dx=20mm, dy=20mm, dz=5mm; Maximum value of SAR (measured) = 0.329 W/kg Zoom:30x30x30,5 (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm; Reference Value = 10.63 V/m; Power Drift = -0.07 dB; Maximum value of SAR (measured) = 0.330 W/kg; Peak SAR (extrapolated) = 0.493 W/kg SAR(1 g) = 0.168 W/kg; SAR(10 g) = 0.061 W/kg Remarks: *. Date tested: 2019/11/19; Tested by: Hiroshi Naka; Tested place:No.7 shielded room, *. liquid depth: 150 mm; Position: distance of EUT to phantom: 0 mm (2 mm to liquid); ambient: (23~24) deg.C. / (60~70 %RH, *. liquid temperature: 23.0(start)/23.0(end)/22.9(in check) deg.C.; *.White cubic: zoom scan area, Red cubic: big=SAR(10g )/small=SAR(1g) Plot 2-1: Front-top-edge & touch, 11a(6Mbps), 5180 MHz->Higher reported SAR(1g), U-NII-1 band EUT: Wireless LAN/Bluetooth combo module in Digital camera; Type: ES204(camera:DS126836); Serial: DE1-C-012(camera:3) Mode: 11a(6Mbps, BPSK/OFDM) (UID: 0, Wi-fi_5GHz (0), Frame Length in ms: 0; PAR: 0; PMF: 1); Frequency: 5180 MHz; Crest Factor: 1.0 Medium: MSL5800(1911); Medium parameters used: f = 5180 MHz; σ = 5.389 S/m; ε r = 46.94; ρ = 1000 kg/m 3 Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY Configuration: -Electronics: DAE4 Sn626; Calibrated: 2019/10/15 / -Phantom: ELI v4.0; Type: QDOVA001BA; Serial: 1059; Phantom section: Flat Section -DASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) / -Probe: EX3DV4 - SN3907; ConvF(4.42, 4.42, 4.42) @ 5180 MHz; Calibrated: 2019/06/19 -Sensor-Surface: 1.4mm (Mechanical Surface Detection (Locations From Previous Scan Used)), Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = 1.0, 25.0, 156.0 body,touch,near-ant2/5b16.53.6;5180,frt-top&d0,a(6m)/ Area:80x60,10 (9x7x1): Measurement grid: dx=10mm, dy=10mm; Maximum value of SAR (measured) = 0.808 W/kg Area:80x60,10 (81x61x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm; Maximum value of SAR (interpolated) = 0.829 W/kg Z;155,5 (1x1x32): Measurement grid: dx=20mm, dy=20mm, dz=5mm; Maximum value of SAR (measured) = 0.862 W/kg Zoom:28x28x24,1.4(ratio) (9x9x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm; Reference Value = 14.42 V/m; Power Drift = -0.03 dB; Maximum value of SAR (measured) = 0.853 W/kg; Peak SAR (extrapolated) = 1.43 W/kg SAR(1 g) = 0.316 W/kg; SAR(10 g) = 0.079 W/kg Remarks: *. Date tested: 2019/11/12; Tested by: Hiroshi Naka; Tested place:No.7 shielded room, *. liquid depth: 150 mm; Position: distance of EUT to phantom: 0 mm (2 mm to liquid); ambient: (23~25) deg.C. / (50~65) %RH, *. liquid temperature: 22.9(start)/23.0(end)/22.9(in check) deg.C.; *.White cubic: zoom scan area, Red cubic: big=SAR(10g )/small=SAR(1g) Test report No. : 13024973S-A-R3 Page : 25 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 APPENDIX 2: SAR Measurement data (cont’d) SAR plot of worst reported SAR Plot 2-2: Front-top-edge & touch, 11a(6Mbps), 5260 MHz->Higher reported SAR(1g), U-NII-2A band EUT: Wireless LAN/Bluetooth combo module in Digital camera; Type: ES204(camera:DS126836); Serial: DE1-C-012(camera:3) Mode: 11a(6Mbps, BPSK/OFDM) (UID: 0, Wi-fi_5GHz (0), Frame Length in ms: 0; PAR: 0; PMF: 1); Frequency: 5260 MHz; Crest Factor: 1.0 Medium: MSL5800(1911); Medium parameters used: f = 5260 MHz; σ = 5.479 S/m; ε r = 46.82; ρ = 1000 kg/m 3 Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY Configuration: -Electronics: DAE4 Sn626; Calibrated: 2019/10/15 / -Phantom: ELI v4.0; Type: QDOVA001BA; Serial: 1059; Phantom section: Flat Section -DASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) / -Probe: EX3DV4 - SN3907; ConvF(4.42, 4.42, 4.42) @ 5260 MHz; Calibrated: 2019/06/19 -Sensor-Surface: 1.4mm (Mechanical Surface Detection (Locations From Previous Scan Used)), Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = 1.0, 25.0, 156.0 body,touch,near-ant/5b6.53.1;5260,frt-top&d0,a(6m)/ Area:80x60,10 (9x7x1): Measurement grid: dx=10mm, dy=10mm; Maximum value of SAR (measured) = 0.471 W/kg Area:80x60,10 (81x61x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm; Maximum value of SAR (interpolated) = 0.564 W/kg Z;155,5 (1x1x32): Measurement grid: dx=20mm, dy=20mm, dz=5mm; Maximum value of SAR (measured) = 0.634 W/kg Zoom:28x28x24,1.4(ratio) (8x8x7)/Cube 0: M…

Text truncated - open the document above for the full version.

Test report No. : 13024973S-A-R3 Page : 47 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) Test report No. : 13024973S-A-R3 Page : 48 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 49 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 50 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 51 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 52 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 53 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 54 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 55 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 56 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-7: Calibration certificate: E-Field Probe (EX3DV4) (cont’d) Test report No. : 13024973S-A-R3 Page : 57 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) Test report No. : 13024973S-A-R3 Page : 58 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) (cont’d) Test report No. : 13024973S-A-R3 Page : 59 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) (cont’d) Test report No. : 13024973S-A-R3 Page : 60 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) (cont’d) Test report No. : 13024973S-A-R3 Page : 61 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) (cont’d) Test report No. : 13024973S-A-R3 Page : 62 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appendix 3-8: Calibration certificate: Dipole (D2450V2) (cont’d) Test report No. : 13024973S-A-R3 Page : 63 of 81 Issued date : April 2, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401 Report Cover Page - 13-EM-F0429 Issue # 15.0 Appen…

Text truncated - open the document above for the full version.

Test report No. : 13024969S-AG Page : 1 of 23 Issued date : March 10, 2020 FCC ID : AZD241 UL Jap an, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN T e l ephone: +81 463 50 6400 Facsimile: +81 463 50 6401 CERTIFICATE 1266.03 RADIO TEST REPORT Test Report No. : 13024969S-AG Applicant : Canon Inc Type of EUT : Wireless LAN/Bluetooth Combo Module Model Number of EUT : ES204 FCC ID : AZD241 Test regulation : FCC Part 15 Subpart E: 2019 Section 15.407 (DFS test only) *Client without radar detection Test Result : Complied (Refer to SECTION 4.2) 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by the A2LA accreditation body. 6. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-Radio test related Requirements. (if applicable) 7. The all test items in this test report are conducted by UL Japan, Inc. Shonan EMC Lab. 8. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. 9. The information provided from the customer for this report is identified in SECTION 1. Date of test : December 20, 2019 Representative test engineer: Kenichi Adachi Engineer Consumer Technology Division Approved by : Toyokazu Imamura Leader Consumer Technology Division The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". Report Cover Page - 13-EM-F0429 Issue # 16.0 Test report No. : 13024969S-AG Page : 2 of 23 Issued date : March 10, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 REVISION HISTORY Original Test Report No.: 13024969S-AG Revision Test report No. Date Page revised Contents - (Original) 13024969S-AG March 10, 2020 - - Test report No. : 13024969S-AG Page : 3 of 23 Issued date : March 10, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 Reference: Abbreviations (Including words undescribed in this report) A2LA The American Association for Laboratory Accreditation NS No signal detect. AC Alternating Current NSA Normalized Site Attenuation AFH Adaptive Frequency Hopping NVLAP National Voluntary Laboratory Accreditation Program AM Amplitude Modulation OBW Occupied Band Width Amp, AMP Amplifier OFDM Orthogonal Frequency Division Multiplexing ANSI American National Standards Institute P/M Power meter Ant, ANT Antenna PCB Printed Circuit Board AP Access Point PER Packet Error Rate Atten., ATT Attenuator PHY Physical Layer AV Average PK Peak BPSK Binary Phase-Shift Keying PN Pseudo random Noise BR Bluetooth Basic Rate PRBS Pseudo-Random Bit Sequence BT Bluetooth PSD Power Spectral Density BT LE Bluetooth Low Energy QAM Quadrature Amplitude Modulation BW BandWidth QP Quasi-Peak Cal Int Calibration Interval QPSK Quadri-Phase Shift Keying CCK Complementary Code Keying RBW Resolution Band Width Ch., CH Channel RDS Radio Data System CISPR Comite International Special des Perturbations Radioelectriques RE Radio Equipment CW Continuous Wave RF Radio Frequency DBPSK Differential BPSK RMS Root Mean Square DC Direct Current RSS Radio Standards Specifications DFS Dynamic Frequency Selection Rx Receiving DQPSK Differential QPSK SA, S/A Spectrum Analyzer DSSS Direct Sequence Spread Spectrum SG Signal Generator EDR Enhanced Data Rate SVSWR Site-Voltage Standing Wave Ratio EIRP, e.i.r.p. Equivalent Isotropically Radiated Power TR Test Receiver EMC ElectroMagnetic Compatibility Tx Transmitting EMI ElectroMagnetic Interference VBW Video BandWidth EN European Norm Vert. Vertical ERP, e.r.p. Effective Radiated Power WLAN Wireless LAN EU European Union EUT Equipment Under Test Fac. Factor FCC Federal Communications Commission FHSS Frequency Hopping Spread Spectrum FM Frequency Modulation Freq. Frequency GFSK Gaussian Frequency-Shift Keying GNSS Global Navigation Satellite System GPS Global Positioning System Hori. Horizontal ICES Interference-Causing Equipment Standard IEC International Electrotechnical Commission IEEE Institute of Electrical and Electronics Engineers IF Intermediate Frequency ILAC International Laboratory Accreditation Conference ISED Innovation, Science and Economic Development Canada ISO International Organization for Standardization JAB Japan Accreditation Board LAN Local Area Network LIMS Laboratory Information Management System MCS Modulation and Coding Scheme MRA Mutual Recognition Arrangement NIST National Institute of Standards and Technology Test report No. : 13024969S-AG Page : 4 of 23 Issued date : March 10, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 CONTENTS PAGE SECTION 1: Customer information ............................................................................................ 5 SECTION 2: Equipment under test (E.U.T.) .............................................................................. 5 SECTION 3: Scope of Report ....................................................................................................... 7 SECTION 4: Test specification, procedures & results ............................................................... 7 SECTION 5: Operation of E.U.T. during testing................................................................…

Text truncated - open the document above for the full version.

Test report No. : 13024969S-AE-R3 P age: 1 of 169 Issued date : April 6, 2020 F CC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401Report Cover Page - 13-EM-F0429 Issue # 16.0 CERTIFICATE 1266.03 RADIO TEST REPORT Test Report No. : 13024969S-AE-R3 Applicant : Canon Inc. Type of EUT : Wireless L AN/Bluetooth Combo Module Model Number of EUT : ES204 FCC ID : AZD241 Test regulation : FCC Part 15 Subpart E: 2019 Test result : Complied (Refer to SECTION 3.2) 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc . 2. The results in this report appl y only to the sample tested. 3. This sample tested is in compliance with the limits of the above re gulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by the A2LA accreditation bod y. 6. Th is test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-Radio test related Requirem ents. (if applicable) 7 . The all test items in this test report are conducted b y UL Japan, Inc. Shonan EMC Lab. 8. The opinions and the interpretations to the result of the description in this report are outside scopes wher e UL Japan has been accred ited. 9. The information provided from the customer for this report is identified in SECTION 1. 10 . This report is a revised version of 13024969S-AE-R2. 13024969S-AE-R2 is replaced with this report. Date of test: October 31, 2019 to January 16, 2020 Representative test engineer: Takahiro Kawakami Engineer Consumer Technology Division A pproved by: Toyokazu Imamura Leader Consumer Technology Division The testing in which “Non-accreditation” is displayed is outside the accreditation scopes in UL Japan. There is no testing item of “Non-accreditation”. Test report No. : 13024969S-AE-R3 Page : 2 of 169 Issued date : April 6, 2020 FCC ID : AZD241 UL Japan, Inc. Shonan EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 13024969S-AE Revision Test report No. Date Page revised Contents - (Original) 13024969S-AE March 9, 2020 - - 1 13024969S-AE-R1 March 30, 2020 P.13 Addition of Support equipment: No. D Gran…

Text truncated - open the document above for the full version.