B5DH215Handheld Wireless microphone

Preliminary Users Manual, Telex FMR-1000 System. Telex Model FMR-1000 Wireless Microphone Receiver. Telex Model WT-1000 Wireless Beltpack Transmitter. Telex Model HT-1000 Wireless Handheld Transmitter. The components above form the Telex “1000” Professional Grade Wireless Microphone System. The system is designed to be used in professional installations where Sound Quality and Reliability are of prime importance. Auto-set features and simplicity of operation are assured along with flexibility for varying venues. These features save valuable installation time at the outset and in the future to help prevent “recalls”. The features of the “1000” system such as user programmable frequencies or pre-programmed frequency sets mean that other users such as Rental Houses with itenerant operations will spend the least amount of time feasible during set-up. Features: Receiver.... • In-Line Receiver Power Supply saves terminal strip occupation. • International Power Supplies and cordsets off the shelf. • Phase Locked Frequencies for stable Operation. • 950 Radio Channels, user programmable or factory installed. • LCD Displays for ease of viewing. • Patented Phase Diversity System. • USB Port for uploading software improvements. • Control Port for remote COR or Relay closure. • Adjustable Line Level ¼ inch output jack. • Fixed Microphone Level XLR output jack. • Front Panel Power ON/OFF Switch. • Quadruple Tuned Ceramic Resonator front end for superior interference rejection. • SAW Filter 1 st I.F for out of band rejection. • Triple ceramic filters in 2 nd I.F for adjacent channel rejection.. • Double Tuned Quadrature circuit for low audio distortion. • On-board MIDAS EQ with Amplitude, Q (bandwidth) and Frequency controls. • Permanent Flash Memory for frequency/system storage. Telex FMR-1000 Page 2 • Front Panel Software Control of Squelch settings with channel monitor. • Double Squelch Amplitude and Tone Squelch system prevents false squelch. • Auto-Select of frequencies speeds set-up time. • Rugged Steel Case with Powder Coat Paint. • Modern front panel design with tamper resistant control cover. Handheld Transmitter...... • 950 Radio Channels, user programmable or factory installed. • Phase Locked Frequencies for Stable Operation. • Efficient current drain vs. power system. • High/Low power switch for range cut/boost or intermod reduction. • Patented Internal Dipole antenna eliminates wires or “rubber duck” antennas. • Removable Heads allow personal selection of available heads. • Specially shaped Handle with “softpaint” for comfort and low handling noise. • 9 Volt Alkaline “rattle-proof” battery area. • Low Profile Audio Mute and Power Switch. • LCD Display for ease of viewing. • On-board frequency program and menu switch. • Superior MIDAS microphone pre-amp design. • Permanent “Flash Memory” for frequency/system storage. • Transmit Tone for squelch control. • Microphone Gain control for talent/head set-up. • Low Battery LED. Beltpack Transmitter..... • 950 Radio Channels, user programmable or factory installed. • Phase Locked Frequencies for Stable Operation. • Efficient current drain vs. power system. • High/Low power switch for range cut/boost or intermod reduction. • Flexible wire rope replaceable antenna. Telex FMR-1000 Page 3 • Microphone/Instrument input connector for personal selection of microphones/instruments or ease of cord change. • Rugged Die Cast housing with wear resistant spatter paint coating. • Non detachable battery door with dual latches. • 9 Volt Alkaline battery operation. Telex Model FMR-1000 UHF Wireless Microphone Receiver The Telex Model FMR-1000 Receiver is a 950 Channel, frequency-selectable full diversity system operating within the frequency range of 520.0 to 746.0 MHz, on specific pre-set bands of frequencies with designated systems for UHF Television Channels . This configuration allows some operation even if several TV channels are in use locally. If any of the TV channels are some distance away from the area where the FMR-1000 is to be used, some of the FMR- 1000 channels can also be used in those channels , with some risk of minor interference. Channel spacing has been computer calculated and programmed to minimize interference. Systems of FMR-1000 and its companion transmitters are capable of operating on at least 5 sets of frequencies in a single TV channel simultaneously, sometimes more depending on the individual venue. Certain frequencies can be combined to form a system of 16. Digital frequency control of the FMR-1000 permits flexibility within a given area and assures confidence in the equipment capability. Specifications: General: (System) Operating Frequency Range.................520-608 and 614-746 MHz in 24 MHz wide bands. Frequency Stability........................... 50 PPM. Channels.......................................950 (25 KHz steps). RF Power Output.......5 mW Low, 50 mW High, typical (terminated). Modulation Type..............................FM, 40 KHz Deviation. Audio Frequency Range......................30-15000 Hz, +/- 2 db. (30-15000 Hz instruments) (80-15000 Hz microphones). Audio Frequency Distortion..................0.5 % THD @ 1000 Hz. Audio Frequency Dynamic Range...........100 db. Audio Frequency Signal/Noise Ratio........100 db. Temperature Range.............................-18 deg.C to 54 deg. C. Telex FMR-1000 System Page 4 FMR-1000 Receiver: Sensitivity......................................0.8 uV for 12 db SINAD Nominal. Image Rejection...............................60 db minimum. Spurious Rejection............................60 db minimum, Selectivity......................................180 KHz at –6 db points. Modulation Acceptance.......................40 KHz nominal deviation. Squelch Type...................................Tone with Amplitude Backup. Squelch Adjustment Range...................0 to 30 uV Typical. Squelch Quieting...............................100 db. Audio Output, mic level.......................-20 dbu. …

Text truncated - open the document above for the full version.

IN MIC AMPLIFIERAMPLIFIERLOW PASS FILTER SWITCH OSCILLATOR PLL MICROPROCESSOR 16 MHZ INTERFACE USER PRE-EMPHASIS HIGH PASS FILTERCOMPRESSORLOW PASS FILTER LIMITER MODULATION HT-1000 BLOCK DIAGRAM 614 TO 746 MHZ 520 TO 608 MHZ

ID LABEL / LOCATION INFO

HT-1000 Theory of Operation A. Audio Input from the microphone is amplified by Q1, Q2, U1 and associated components. VR1 is user adjustable and varies the gain from 0 to 26 dB. U2A is a high pass filter with a cutoff frequency of 80 Hz. C11, R17 and R18 provide pre-emphasis at 50 microseconds. U4 is a 2:1 compressor that is used for noise reduction. The high frequencies are routed through U4B and the low frequencies through U4A. U3, Q3 and associated components comprise a modulation limiter. U3A detects positive peaks and U3B detects the negative. The resulting current turns on Q3 which then reduces the gain of U4. U2B is a low pass filter with a cutoff frequency of 30 kHz. VR4 is used to set the level of an ultrasonic tone used for squelch coding. VR3 is used to set the frequency deviation. B. RF Output HY1 is a VCO that runs at the output frequency. No multiplication takes place in the RF chain. Q4, Q5, Q8 and Q10 buffer and amplify the carrier. C62, C63, C64, L12 and L13 form a matching network and low pass filter. Q6 and Q9 are used to control the current through the amplifier section. Q7 is used to switch the amplifier on after the synthesizer achieves lock. C. Synthesizer U5 is a PLL that is serially loaded from microprocessor U104. RF from the VCO is fed to the PLL via C38 and R48. Y101 provides the reference frequency for U5. VC101 is used to set this to exactly 16 MHz. U5 controls the VCO through the loop filter consisting of R46, R47, C39, C40 and C41. Modulation is fed to the bottom of C39.

U.S. LOW 680-704MHZ U.S. HI 722-746MHZ GERMAN 798-822MHZ U.K. 841-862MHZ 879440- -1-2-3-4 ITEMNEW QTYQTYQTYQTY TYPEDESCRIPTIONPART NO.DESIGNATOR 1 5555CAP10UF TANT A102877047TC1,C12,C14,C39,C43 2 8888CAP100PF 0603723482130TC2,C18,C22,C30,C54,C60,C65, C69 3 5555CAP1UF TANT A102877012TC3,C13,C15,C26,C31 4 1111CAP.1UF TANT A102877006TC4 5 1111CAP22UF TANT B102877063TC5 6 2222CAP470PF 0603723482138TC6,C23 7 5555CAP.1UF 080572338530TC7,C8,C9,C19,C40 8 2222CAP.22UF TANT A102877008TC10,C21 9 1111CAP.0015UF 08057233859TC11 10 1111CAP2.2UF TANT A102877042TC16 11 1111CAP4.7UF TANT A102877067TC17 12 1111CAP.047UF 080572338526TC20 131111CAP.0068UF 080572338517T C24 14 1111CAP.015UF 080572338520TC25 15 1111CAP.01UF 0603102881703TC27 1618181818 CAP.001UF 0603102881717T C28,C29,C32,C34,C37,C41,C42,C45,C48, C49,C50,C52,C55,C56,C58,C59,C61,C67 17 3333CAP.1UF 0603723489101TC33,C35,C36 18 1111CAP10PF 0603723482116TC38 19 1111CAP5.6PF 0603723482113TC44 20 CAP3.9PF 0603723482110T 22-2C46,C64 --1-C46 21 1111CAP12PF 0603723482117TC47 22 1111CAP1.5PF 0603723482103TC51 23 CAP3.3PF 0603723482109T 33--C53,C57,C63 --22C53,C57 24 11--CAP1PF 0603723482101TC62 25 --11CAP2.7PF 0603723482107TC63 26 1111CAP22PF 0603723482121TC66 27 1111DIODEBAW56102253000TD1 28 1111DIODEBAV99760481TD2 29 1---VCO680-704 MHz7603004THY1 30 -1--VCO722-746 MHz7603006THY1 31 --1-VCO798-822 MHz7603009THY1 32 ---1VCO841-865 MHz76030010THY1 33 1111CONNSAMTEC TFM640147J1 34 11111111IND.22UH 080572350828TL1,L2,L3,L4,L5,L6,L7,L10,L11,L14,L15 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS:DR BY: DDN DATE: 10/17/00 PROD:___ DATE:___ CHKD BY: TY DATE: 07/30/01 APPD BY: RB DATE: 07/30/01 879440 REV LEVEL: PCB ASSY, MAIN HT/CSH-1000 SMT TITLE: PART NO: A Page 2 of 6 U.S. LOW 680-704MHZ U.S. HI 722-746MHZ GERMAN 798-822MHZ U.K. 841-862MHZ 879440- -1-2-3-4 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS:DR BY: DDN DATE: 10/17/00 PROD:___ DATE:___ CHKD BY: TY DATE: 07/30/01 APPD BY: RB DATE: 07/30/01 879440 REV LEVEL: PCB ASSY, MAIN HT/CSH-1000 SMT TITLE: PART NO: A 35IND8NH 080572350812T 222-L8,L13 ---3L8,L12,L13 36 1111IND22NH 080572350816TL9 37 1---IND18NH 080572350815TL12 38 -1--IND15NH 080572350814TL12 39 --1-IND12NH 080572350813TL12 40 2222TRANSMMBT508716025087SMTQ1,Q2 41 3333TRANSMMBT390654716200Q3,Q6,Q9 42 4444TRANSBFG540X760209TQ4,Q5,Q8,Q10 43 1111TRANSMMBT390454671200TQ7 44 RES100 OHM 0603723481100T 44--R1,R52,R65, R67 --55R1,R52,R62,R65,R67 45 2222RES475 OHM 0603723481165TR2, R48 46 10101010RES10K 0603723481300T R3,R21,R22,R24,R25,R27,R28,R56,R59,R 60 47 1111RES39.2K 0603723481357TR4 48 1111RES26.7K 0603723481341TR17 49 1111RES75K 0603723481384TR5 50 1111RES121K 0603723481408TR6 51 2222RES1.82K 0603723481225TR7,R9 52 1111RES332 OHM 0603723481150TR8 53 8888RES1K 0603723481200TR10,R11,R38,R39,R40,R41,R42, R66 54 1111RES249 OHM 0603723481138TR12 55 1111RES14.3K 0603723481315TR13 56 1111RES5.62K 0603723481272TR14 57 1111RES187K 0603723481426TR15 58 1111RES215K 0603723481432TR16 59 1111RES6.65K 0603723481279TR18 60 1111RES33.2 OHM 0603723481050TR19 61 1111RES3.32K 0603723481250TR20 62 1111RES12.1K 0603723481308TR23 63 3333RES20K 0603723481329TR26,R33,R36 64 3333RES4.75K 0603723481265TR29,R31,R47 65 3333RES2.21K 0603723481233TR30,R32, R34 66 1111RES30.1K 0603723481346TR37 67 1111RES56.2K 0603723481372TR43 68 1111RES200K 0603723481429TR44 69 RES47.5 OHM 0603723481065T 44--R45,R49,R50,R61 Page 3 of 6 U.S. LOW 680-704MHZ U.S. HI 722-746MHZ GERMAN 798-822MHZ U.K. 841-862MHZ 879440- -1-2-3-4 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS:DR BY: DDN DATE: 10/17/00 PROD:___ DATE:___ CHKD BY: TY DATE: 07/30/01 APPD BY: RB DATE: 07/30/01 879440 REV LEVEL: PCB ASSY, MAIN HT/CSH-1000 SMT TITLE: PART NO: A --33R45,R49,R50 70 1111RES750 OHM 0603723481184TR46 71 1111RES22.1K 0603723481333TR51 72 1111RES22.1 OHM 0603723481033TR53 73 1111RES6.81K 0603723481280TR54 74 1111RES150 OHM 1206102404117TR55 75 1111RES47.5K 0603723481365TR57 76 2222RES10 OHM 0603723481000TR58, R64 77 --11RES26.7 OHM 0603723481041TR61 78 11--RES130 OHM 0603723481111TR62 79 1111IC5534AD-T T & R53293002TU1 80 1111ICLM83316030833SMTU2 81 1111ICLM35853227104TU3 82 1111ICSA57153277002TU4 83 1111ICTRF2050760242SU5 84 1111POT10K 7235209TVR4 85 1111POT20K72352010TVR3 86 1111PC BOARD HH MAIN TRANSMIT750554 87 A/RA/RA/RA/RPASTESOLDER PASTEBE738 88 1111CAP.0047UF 0603723483111TC68 89 1111RES4.75K 1206102404265TR63 90 1111RES18.2K 0603723481325TR35 91 --1-CAP4.7PF 0603723482111TC64 Page 4 of 6 ITEMNEW QTY TYPEDESCRIPTIONPART NO.DESIGNATOR 1 1CAP.1UF 0603723489101TC201 2 1ICPCF8566 VSO40760303TU201 3 1XMIT HAND HELD DISPLAY PCB750555 4 A/RSOLDER PASTEBE738 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS:DR BY: SMH DATE: 10/03/00 PROD:___ DATE:___ CHKD BY:DDN DATE:8/4/01 APPD BY:R.B. DATE:8/7/01 879442 REV LEVEL: PCB SMT ASSY DISPLAY, HT/CSH-1000 SMT TITLE: PART NO: A Page 2 of 3 879445-2 ITEMNEW QTY TYPEDESCRIPTIONPART NO.DESIGNATOR 11CAP.01UF 0805 16V72350125TC1 21CAP.056UF 121072350134T C2 3 1RES100 OHM 0603723481100TR1 4 1 PC BOARD ROSE II CARTRIDGE 750557 5 A/RSOLDERPASTEBE738 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disc…

Text truncated - open the document above for the full version.

FCC ID: B5DH215 MFA p0170013, d0180016 Date of Report: Date of Submission: August 6, 2001 August 20, 2001 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Telex Communications, Inc. Equipment: Telex HT-1000/Electro-VoiceCSH-1000 FCC ID: B5DH215 FCC Rules: Radiofrequency Radiation Exposure Limits 47 CFR 1.1310 CALCULATED TEST RESULTS MPE - Mobiles x Fixed Based Station Gentlemen: On behalf of the Applicant, enclosed please find the Supplemental Test Report, the whole for Environmental Assessment (MPE) of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: B5DH215 MFA p0170013, d0180016 ENVIRONMENTAL ASSESSMENT for MOBILES for FCC ID: FCC ID: B5DH215 Models:Telex HT-1000 and Electro-VoiceCSH-1000 to FEDERAL COMMUNICATIONS COMMISSION 47 CFR 1.1310 (MPE) Radiofrequency Radiation Exposure Limits DATE OF REPORT: August 6, 2001 ON THE BEHALF OF THE APPLICANT: Telex Communications, Inc. AT THE REQUEST OF: P.O. 238030 Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 Attention of: Charles E. Conner, Project Engineer (402) 467-5321; FAX: -3279 E-mail: [email protected] SUPERVISED BY: Morton Flom, P. Eng. FCC ID: B5DH215 MFA p0170013, d0180016 TABLE OF CONTENTS RULEDESCRIPTIONPAGE . Test Report 1 . Identification of the Equipment Under Test 2 . Standard Test Conditions and Engineering Practices 4 1.1310 Environmental Assessment 5 FCC ID: B5DH215 MFA p0170013, d0180016 PAGE NO.1of5. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT (SUPPLEMENTAL) b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0180016 d) Client: Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 e) Identification: FCC ID: B5DH215 Models: Telex HT-1000 Electro-Voice CSH-1000 EUT Description: UHF Wireless Handheld Microphone Transmitter f) EUT Condition: Not required unless specified in individual tests. g) Report Date: August 6, 2001 EUT Received: June 8, 2001 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. FCC ID: B5DH215 MFA p0170013, d0180016 PAGE NO.2of5. IDENTIFICATION OF THE EQUIPMENT UNDER TEST (EUT) NAME AND ADDRESS OF APPLICANT: Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 MANUFACTURER: Telex Communications, Inc. FCC ID: B5DH215 MODEL NOs: Telex HT-1000 Electro-VoiceCSH-1000 DESCRIPTION: UHF Wireless Microphone Transmitter TYPE OF EMISSION: 91K0F3E FREQUENCY RANGE, MHz: 520 to 608 614 to 746 POWER RATING, Watts: 0.050 Switchable Variable x N/A MODULATION: AMPS TDMA CDMA x OTHER ANTENNA: HELICAL MONOPOLE WHIP x OTHER NOTE: For RF Safety test antenna gain taken at the upper range of expected gain (i.e. 0 dBd) and RF Power set to highest nominal power across all channels. FCC ID: B5DH215 MFA p0170013, d0180016 PAGE NO.3of5. M. Flom Associates, Inc. is accredited by the American Association for Laboratory Association (A2LA) as shown in the scope below. "This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this report have been determined in accordance with the laboratory's terms of accreditation unless stated otherwise in the report." Should this report contain any data for tests for which we are not accredited, or which have been undertaken by a subcontractor that is not A2LA accredited, such data would not covered by this laboratory's A2LA accreditation. FCC ID: B5DH215 MFA p0170013, d0180016 PAGE NO.4of5. STANDARD TEST CONDITIONS and ENGINEERING PRACTICES Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.4-1992/2000, section 6.1.9, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10°to 40°C (50°to 104°F) unless the particular equipment requirements specify testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Prior to testing, the EUT was tuned up in accordance with the manufacturer's alignment procedures. All external gain controls were maintained at the position of maximum and/or optimum gain throughout the testing. Measurement results, unless otherwise noted, are worst case measurements. FCC ID: B5DH215 MFA p0170013, d0180016 PAGE NO.5of5. MPE CALCULATION Power Output = ERP Frequency = 520 MHz Uncontrolled Exposure Limit = f/1500 = 0.34667 mw/cm 2 R meters =[P ERP /(4πx Limit)] 1/2 = [(13.56 x 10 -3 )/(12.56 x 3.4667)] 1/2 = 0.01745 m = 1.8 cm = less than 1 inch SUPERVISED BY: Morton Flom, P. Eng. FCC ID: B5DH215 MFA p0170013, d0180016 (The following will be placed in the Instruction Manual) MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS & USERS Use only manufacturer or dealer supplied antenna. Antenna Minimum Safe Distance: 1.8 cm . Antenna Gain: zero dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. Antenna Mounting:The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer t…

Text truncated - open the document above for the full version.

770672a.sch-1 - Mon Jul 30 10:16:03 2001 770680A.sch-1 - Tue Aug 07 11:54:31 2001 770682a.sch-1 - Wed Aug 15 08:11:52 2001 770683A.sch-1 - Fri Jul 27 09:32:43 2001

FCC ID: B5DH215 MFA p0170013, d0180015 Date of Report: Date of Submission: August 6, 2001 August 20, 2001 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Telex Communications, Inc. Equipment: Telex HT-1000 Electro-Voice CSH-1000 FCC ID: B5DH215 FCC Rules: 74H Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: B5DH215 MFA p0170013, d0180015 LIST OF EXHIBITS (FCCCERTIFICATION(TRANSMITTERS) - REVISED 9/28/98) APPLICANT: Telex Communications, Inc. FCC ID: B5DH215 BY APPLICANT: 1. LETTER OF AUTHORIZATION 2. IDENTIFICATION DRAWINGS, 2.1033(c)(11) LABEL LOCATION OF LABEL COMPLIANCE STATEMENT LOCATION OF COMPLIANCE STATEMENT 3. PHOTOGRAPHS, 2.1033(c)(12) 4. DOCUMENTATION: 2.1033(c) (3) USER MANUAL (9) TUNE UP INFO (10) SCHEMATIC DIAGRAM (10) CIRCUIT DESCRIPTION BLOCK DIAGRAM PARTS LIST ACTIVE DEVICES 5. PART 90.203(e) & (g) ATTESTATION BY M.F.A. INC. A. TESTIMONIAL & STATEMENT OF CERTIFICATION B. STATEMENT OF QUALIFICATIONS FCC ID: B5DH215 MFA p0170013, d0180015 TRANSMITTER CERTIFICATION of FCC ID: B5DH215 MODELS: Telex HT-1000 and Electro-Voice CSH-1000 to FEDERAL COMMUNICATIONS COMMISSION Rule Part(s) 74H DATE OF REPORT: August 6, 2001 ON THE BEHALF OF THE APPLICANT: Telex Communications, Inc. AT THE REQUEST OF : P.O. 238030 Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 Attention of: Charles E. Conner, Project Engineer (402) 467-5321; FAX: -3279 E-mail: [email protected] SUPERVISED BY: Morton Flom, P. Eng. FCC ID: B5DH215 MFA p0170013, d0180015 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. FCC ID: B5DH215 MFA p0170013, d0180015 TABLE OF CONTENTS RULEDESCRIPTIONPAGE . Test Report 1 2.1033(c) General Information Required 2 2.1033(c)(14) Rule Summary 5 . Standard Test Conditions and Engineering Practices 6 2.1046(a) Carrier Output Power (Conducted) 7 2.1046(a) R. F. Power Output (Radiated) 9 2.1051 Unwanted Emissions (Transmitter Conducted) 11 2.1053(a) Field Strength of Spurious Radiation 14 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 18 2.1047(a) Audio Frequency Response 26 2.1047(b) Modulation Limiting 28 2.1055(a)(1) Frequency Stability (Temperature Variation) 31 2.1055(b)(1) Frequency Stability (Voltage Variation) 34 2.202(g) Necessary Bandwidth and Emission Bandwidth 35 FCC ID: B5DH215 MFA p0170013, d0180015 PAGE NO.1of35. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0180015 d) Client: Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 e) Identification: FCC ID: B5DH215 Models: Telex HT-1000 Electro-Voice CSH-1000 EUT Description: UHF Wireless Handheld Microphone Transmitter f) EUT Condition: Not required unless specified in individual tests. g) Report Date: August 6, 2001 EUT Received: June 8, 2001 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. FCC ID: B5DH215 MFA p0170013, d0180015 PAGE NO.2of35. LIST OF GENERAL INFORMATION REQUIRED FOR CERTIFICATION IN ACCORDANCE WITH FCC RULES AND REGULATIONS, VOLUME II, PART 2 AND TO 74HSub-part 2.1033 (c)(1): NAME AND ADDRESS OF APPLICANT: Telex Communications, Inc. 8601 E. Cornhusker Highway P.O. Box 5579 Lincoln, NE 68505-5579 MANUFACTURER: Telex Communications, Inc. (c)(2): FCC ID: B5DH215 MODEL NOs: Telex HT-1000 Electro-Voice CSH-1000 (c)(3): INSTRUCTION MANUAL(S): PLEASE SEE ATTACHED EXHIBITS (c)(4): TYPE OF EMISSION: 91K0F3E (c)(5): FREQUENCY RANGE, MHz : 520 to 60…

Text truncated - open the document above for the full version.