B5KAKRC1311004-2PCS Broadband GSM Base station

  

      !"!# P r e l i m i n a r y P r e l i m i n a r y E RBS 2106, RBS 2206 Reference Manual RBS 2106, RBS 2206 Reference Manual © Ericsson Radio Systems AB — All Rights Reserved — EN/LZT 720 0008 P2A 2001-11-28 1 (485) © Ericsson Radio Systems AB — All Rights Reserved — P r e l i m i n a r y RBS 2106, RBS 2206 Reference Manual Due to continued progress in methodology, design and manufacturing, the contents of this document are subject to revision without notice. 2 (485) EN/LZT 720 0008 P2A 2001-11-28 © Ericsson Radio Systems AB — All Rights Reserved — P r e l i m i n a r y RBS 2106, RBS 2206 Reference Manual Contents 1 Preface ........................................................................................................... 15 1.1 Objectives ................................................................................................ 15 1.2 Target Groups..........................................................................................15 1.3 RBS 2000 Library Overview.................................................................... 15 1.4 How to Order CPI....................................................................................16 1.5 R1A to P2A..............................................................................................17 2 Product Safety Requirements RBS 2000....................................................19 2.1 References...............................................................................................19 2.2 Product Safety ......................................................................................... 19 3 Environmental Capabilities..........................................................................21 3.1 Scope.......................................................................................................21 3.2 Terminology ............................................................................................. 21 3.3 References...............................................................................................22 3.4 Transport -40  C - +70  C..........................................................................22 3.5 Storage -25  C - +55  C.............................................................................23 3.6 Handling -40  C - +70  C........................................................................... 25 3.7 Operation Indoor +5  C - +40  C ............................................................... 25 3.8 Operation Outdoor -33  C - +40  C ........................................................... 27 3.9 Operation Outdoor -33  C - +45  C ........................................................... 28 3.10 Operation Outdoor -33  C - +55  C ......................................................... 30 3.11 Operation Mast Mounted Equipment -33  C - +45  C.............................30 3.12 Operation Mast Mounted Equipment -33  C - +55  C............................30 4 Radio Configurations, RBS 2106 and RBS 2206.......................................33 4.1 Introduction .............................................................................................. 33 4.2 References...............................................................................................34 4.3 Definitions ................................................................................................ 34 4.4 Frequency Bands.....................................................................................36 4.5 Basic Configurations................................................................................37 4.6 Site Cell Configurations (SCC)................................................................69 4.7 Co-Siting with RBS 200 or RBS 2000 Macro Cabinets .......................... 78 EN/LZT 720 0008 P2A 2001-11-28 3 (485) © Ericsson Radio Systems AB — All Rights Reserved — P r e l i m i n a r y RBS 2106, RBS 2206 Reference Manual 4.8 Co-Siting with TDMA RBS Using an ASU .............................................. 82 5 Product Data RBS 2106................................................................................87 5.1 Introduction .............................................................................................. 87 5.2 RBS 2106 Cabinet Description................................................................87 5.3 Connection Interfaces..............................................................................96 5.4 RBS Power System................................................................................. 101 5.5 Antenna System ...................................................................................... 105 5.6 Transmission............................................................................................106 6 Product Data RBS 2206................................................................................109 6.1 Site Equipment Overview ........................................................................ 109 6.2 Site Power Options..................................................................................110 6.3 Power Connections..................................................................................110 6.4 RBS 2206 Cabinet Hardware Description...............................................114 6.5 External Alarm and Transmission Interface ............................................ 123 6.6 BBS 2000 Rack Description.................................................................... 127 6.7 Antenna System ...................................................................................... 129 7 Unit Description, DXU-21 ............................................................................. 147 7.1 System Environment................................................................................147 7.2 Block Diagram .................................................................................…

Text truncated - open the document above for the full version.

Open EXHIBIT 13 1 (1) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A B5KAKRC1311004-2 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch SP Sveriges Provnings- och ForskningsInstitut Brinellgatan 4 Box 857 S-501 15 Borås Sweden September 18, 2002 Subject: Certification for FCC ID: B5KAKRC1311004-2 Gentlemen; Ericsson AB requests a Grant of Certification (Type Acceptance) for the above mentioned FCC Identifier. This base station transceiver is designed for use in the GSM 1900 MHz cellular telephone system. The transmitter will operate from 1930.4 to 1989.6 MHz. The receiver circuit supports 1850.4 to 1809.6 MHz. The base station operates in the 1900 MHz broadband PCS services as per 47 CFR Part 24 subpart E. It meets the requirements of GSM1900 11.10-1 version 4.19.1 specification for operation in GSM cellular systems. This base station will in normal mode operate at a nominal power out of 28 watts at the antenna connector. In TCC mode with two transmitters combined on the same frequency is the nominal output power 50 watts. The power output is reducible to ~0.3 watts. The channels at the band edges (channel 512 – 1930.2 MHz and channel 810 – 1989.8 MHz) are excluded. This is because of too wide frequency spectrum at the band edges. This exclusion is done by database settings in the switch software. These channels will never be set there. These database settings will also control internal band edges and exclude channels that neighbors other than GMSK or EDGE channels. This is a part of the cell planning by the operator. Ericsson AB requests confidentiality under CFR 0.459. Confidentiality for the following exhibits is requested: Exhibit 5 CPU Part Schematics Exhibit 5 RF Part Schematics Justification of this request is in order to protect the large investment in developing this technology and to facilitate the circuit miniaturization utilized in this design and protect the innovative design as well as proprietary techniques which are implemented. In order to protect Ericsson’s competitive advantage on these proprietary techniques, we request the above listed exhibits be held as confidential and withheld from the Public Information File. If additional information is needed, please contact me on the below listed number. Sincerely, Larry Lindström Staff Engineer, Regulatory Programs Ericsson AB Torshamnsgatan 21-23 (Färögatan 6) Kista, SE-164 80 Stockholm Sweden Telephone No.: +46 8 764 12 73 Fax No.: +46 8 404 44 20 e-mail [email protected]

Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 Transceiver Unit KRC 131 1004/2, R1B Front side Rear side Bottom side

Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 Transceiver Unit KRC 131 1004/2, R1B ID Label Label placement

Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 Transceiver Unit KRC 131 1004/2, R1B Main board Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 Main board- PCB component side Main board- PCB rear side Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 PA1- PCB components side PA1- PCB rear side Datum/Date Beteckning/Reference Sida/Page 2002-09-11 FCC ID: B5KAKRC1311004-2 PA2- PCB components side PA2- PCB rear side

Open EXHIBIT 12 1 (10) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström B5KAKRC1311004-2 Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A Exhibit 12 – Cover Sheet Contents 1 2.1033(c) Circuit Description 2 1.1 (2) FCC Identifier: B5KAKRC1311004-2 2 1.2 (4) Type of Emission: 2 1.3 (5) Frequency range: 1930.4 to 1989.6 MHz 2 1.4 (6) Range of Operating Power: 2 1.5 (7) Maximum Power Rating: 2 1.6 (8) Final Amplifier Voltage and Current in normal operation 3 1.7 (10) Frequency Stabilizing Circuit Description 3 1.8 (10) Spurious and Harmonic Suppression 3 1.9 (10) Limiting Power 3 1.10 (10) Digital Modulation 5 1.10.1 Modulation format for GMSK 5 1.10.2 Modulation format for 8PSK 8 Open EXHIBIT 12 2 (10) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström B5KAKRC1311004-2 Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A 1 2.1033(c) Circuit Description 1.1 (2) FCC Identifier: B5KAKRC1311004-2 This dTRU (double Tranceiver Radio Unit) consist of two synthesized transmitters (TRX) operating in the frequency band of 1930.4 to 1989.6 MHz. There are 297 Channels available with a channel spacing of 200 KHz. The transmitter is capable of operation in a TDMA (Time Division Multiple Access) system. For each channel there are 8 time slots available,each containing digital speech or data for GMSK and data for 8-PSK. The dTRU have a hybrid combiner included which can be used to increase the number of TRX:s per antenna. The combiner can alternativately be used to increase the output power (TCC = Transmitter Coherent Combining) by using the same transmit frequency channel in both TRX:s. This combiner is connected before the cavity band pass filter in the combining system. 1.2 (4) Type of Emission: GMSK: 258KGXW 8-PSK: 258KG7W 1.3 (5) Frequency range: 1930.4 to 1989.6 MHz 1.4 (6) Range of Operating Power: This transmitter is designed to supply a nominal power level of 44.5 dBm at the antenna connector. The power level can be set at 16 power levels, each with a 2 dB increment. The power levels are labeled P(0) to P(15) where P(0) is the highest power level. In TCC mode with both TRX:s combined will the combination supply a nominal power level of 47 dBm at the antenna connector. The power level can be set at 16 power levels, each with a 2 dB increment. The power levels are labeled P(0) to P(15) where P(0) is the highest power level. 1.5 (7) Maximum Power Rating: The maximum power rating with one TRX under environmental and supply voltage variations is equal to 44.5 dBm plus a power level tolerance of + 1.3 dB. Therefore the maximum output power is 45.8 dBm equal to 38 W at the antenna connector of the radio base station. The maximum power rating with two TRX.s combined (TCC) under environmental and supply voltage variations is equal to 47 dBm plus a power level tolerance of + 1.3 dB. Therefore the maximum output power with TCC is 48.3 dBm equal to 67.6 W at the antenna connector of the radio base station. Open EXHIBIT 12 3 (10) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström B5KAKRC1311004-2 Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A 1.6 (8) Final Amplifier Voltage and Current in normal operation P (0) P (15) Collector Voltage 26.0 Volt DC 26.0 Volt DC Collector Current 4.9 Amps DC 0.7 Amps DC 1.7 (10) Frequency Stabilizing Circuit Description The transmitter in each TRX contains three synthesized oscillators. One PLL gives a 160 MHz signal to the I/Q modulator. The two other generate a 1770 to 1830 MHz signal to the mixer where the modulated signal is converted to the transmit frequency. Two oscillators are needed in frequency hopping mode, one is retuning while the other is active. All three synthesized oscillators have a reference of 13 MHz, which is downmixed by 2, generated in a central synthesized oscillator (PLL) of 26 MHz in the LTU part of the dTRU. This PLL frequency reference is extracted from the 13 MHz signal on the Y-link, which is generated and distributed, by the DXU (Distribution Switch Unit), to all dTRU:s in the basestation. The frequency reference 13 MHz in the DXU is generated in a voltage controlled oscillator placed in an oven together with and phase-locked to a long term stable oven heated oscillator. As an option can the oscillator be phase-locked to the incoming PCM-link frequency or an incoming GPS-link frequency. 1.8 (10) Spurious and Harmonic Suppression Spurious and harmonic suppression is achieved by using two separate bandpass filters of ceramic type in the exciter. A filter module at the output works like a bandpass filter around the carrier. In addition to these filters, the output signal passes a cavity band pass filter in the combining system. 1.9 (10) Limiting Power The TRU measures the output power at its output connector via a RF-detector and the detected value is used by the power loop control block to steer two variable gain amplifiers beteween the modulator and the power amplifier. Open EXHIBIT 12 4 (10) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström B5KAKRC1311004-2 Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A In TCC (Transmitter Coherent Combining) mode is the output power also measured with a RF detector in the non-output branch of the hybride combiner in the dTRU. This output power is kept as low as possible, by keeping the TRX:s output power in phase with each other, to get maximum output power at the output branch of the hybride combiner Open EXHIBIT 12 5 (10) Prepared (also subject responsible if other) No. ERA/RKF/VR Larry Lindström B5KAKRC1311004-2 Approved Checked Date Rev Reference KI/ERA/RKF/VR (L Lindström) 2002-09-18 A 1.10 (10) Digital Modulation 1.10.1 Modulation format for GMSK 1.10.1.1 Modulating symbol rate The modulating symbol rate is 1/T = 1 625/6 ksymb/s (i.e. approximately 270.833 ksymb/s), which corresponds to 1 625/6 k…

Text truncated - open the document above for the full version.

Open EXHIBIT 101 (22) Prepared (also subject responsible if other)No. ERA/RKF/VR Larry LindströmB5KAKRC1311004-2 ApprovedCheckedDateRevReference KI/ERA/RKF/VR (L Lindström)2002-09-13A Exhibit 10 – Components, Tune Up Contents 12.1033 (c) (10) Function of Active Circuit Devices..........................2 1.1Printed Board RSU 1900 MHz GMSK/8-PSK ROA 117 8461/1......2 1.1.1Function Block LTU..........................................................................2 1.1.2Function Block DC/DC.....................................................................3 1.1.3Function Block Rx Frontend 1900 MHz...........................................5 1.1.4Function Block RX IF1 GMSK/8-PSK 1900 MHz.............................7 1.1.5Function Block RX IF2 GMSK/8-PSK 1900 MHz.............................8 1.1.6Function Block CPU.........................................................................9 1.1.7Function Block SPARC 1 GMSK/8-PSK........................................11 1.1.8Function Block SPARC 2 GMSK/8-PSK........................................12 1.1.9Function Block TX1 GMSK/8-PSK 1900 MHz...............................13 1.1.10Function Block TX2 GMSK/8-PSK 1900 MHz...............................14 1.2Printed Board PBU1 1900 GMSK/8-PSK Hybrid Combiner ROA 219 5387/1.............................................................................................15 1.2.1Function Block DC Booster............................................................15 1.2.2Function Block PA Linearisation GMSK/8-PSK PBU1900...........17 1.2.3Function Block PA, PBU 1900........................................................18 1.2.4Function Block Hybrid Combiner, PBU 1900.................................19 1.3Printed Board PBU1 1900 GMSK/8-PSK wo Hybrid Combiner ROA 219 5388/1.............................................................................................20 1.3.1Function Block DC Booster............................................................20 1.3.2Function Block PA Linearisation GMSK/8-PSK PBU1900...........20 1.3.3Function Block PA, PBU 1900........................................................20 22.1033(c)(9) Tune-Up Procedure...................................................21 32.1033(c)(9,10) Power Tune-Up – Power Limiting........................22 Open EXHIBIT 102 (22) Prepared (also subject responsible if other)No. ERA/RKF/VR Larry LindströmB5KAKRC1311004-2 ApprovedCheckedDateRevReference KI/ERA/RKF/VR (L Lindström)2002-09-13A 1 2.1033 (c) (10) Function of Active Circuit Devices 1.1 Printed Board RSU 1900 MHz GMSK/8-PSK ROA 117 8461/1 1.1.1 Function Block LTU Product ROZ 104 033/1 Revision PF1 PosProd name/DesProduct number V500DIODE/SCHx2 70V 70mA SOT23 SerialRKZ 323 08/2 Z500MICROCIRCUIT/REG LIN+ ADJ 1.8-20V +/-1% 500 RYT 113 6303/1 Z501MICROCIRCUIT/74'74 AC SOP14 2xD FLIP- FLOP RYT 318 0074/C Z503MICROCIRCUIT/MB15E07 PFV-ERRYT 102 6057/1 Z504OSCILLATOR/26.000MHZRTL 202 610/02 Z505MICROCIRCUIT/74'04 LVC SSOP14 6x INVERTER RYT 331 0004/C Z506MICROCIRCUIT/74'04 ACT TSSOP14 6x INVERTER RYT 317 6004/22C Z507MICROCIRCUIT/74'04 ACT TSSOP14 6x INVERTER RYT 317 6004/22C Open EXHIBIT 103 (22) Prepared (also subject responsible if other)No. ERA/RKF/VR Larry LindströmB5KAKRC1311004-2 ApprovedCheckedDateRevReference KI/ERA/RKF/VR (L Lindström)2002-09-13A 1.1.2 Function Block DC/DC Product ROZ 104 032/1 Revision M PosProd name/DesProduct number T700TRANSFORMER/PLANARTRANSFORMER T40REG 735 305/2 T702TRANSFORMER/PLANARTRANSFORMER T25REG 735 304/2 V700RECTIFIER/SCHx2 30V 2x15A D2PAKRKZ 323 6012/3 V702RECTIFIER/SCHx2 30V 2x6A DPAK(TO252AA)RKZ 323 6047/1 V703OVERVOLTAGEPROT./DIODE TS 36V 30A DO- 214AB RKZ 223 485/36 V708RECTIFIER/REC 200V 1A 35ns SMA (DO214AC)RKZ 123 05/2 V709RECTIFIER/REC 200V 1A 35ns SMA (DO214AC)RKZ 123 05/2 V710TRANSISTOR/NFET 100V 6A SO8 0.026ohmRYN 123 6032/1 V711TRANSISTOR/NFET 100V 6A SO8 0.026ohmRYN 123 6032/1 V712TRANSISTOR/NFET 100V 6A SO8 0.026ohmRYN 123 6032/1 V714TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V715TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V716TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V717TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V718TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V719TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V720TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V721TRANSISTOR/NFET 30V 14A SO8 0.008ohmRYN 123 6012/1 V722RECTIFIER/SCH 25V 10A SMBRKZ 323 6038/1 V723RECTIFIER/SCH 25V 10A SMBRKZ 323 6038/1 V724RECTIFIER/SCH 25V 10A SMBRKZ 323 6038/1 V725RECTIFIER/SCH 25V 10A SMBRKZ 323 6038/1 V727TRANSISTOR/N chanl. MOSFETRYN 123 251/C V728TRANSISTOR/N chanl. MOSFETRYN 123 251/C V729DIODE/SWI 75V 0.25A SOT23RKZ 123 612 V730DIODE/SWI 75V 0.25A SOT23RKZ 123 612 V736REG.DIODE/REG 12.0V 6% 0.2W SOT-23RKZ 223 01/18 V738OVERVOLTAGEPROT./DIODE TS 36V 30A DO- 214AB RKZ 223 485/36 V746DIODE/SWI 75V 0.25A SOT23RKZ 123 612 V747DIODE/DUAL SERIES 70V .2A 6ns SOT-23RKZ 123 03/1 V748DIODE/DUAL SERIES 70V .2A 6ns SOT-23RKZ 123 03/1 V749TRANSISTOR/NFET 100V 6A SO8 0.026ohmRYN 123 6032/1 V750TRANSISTOR/NFET 100V 6A SO8 0.026ohmRYN 123 6032/1 Z703MICROCIRCUIT/REG SW- ADJ 150kHz 0.5ARYT 113 6320/1 Z705MICROCIRCUIT/LM431 ADJ REGULATORRYT 113 008/3C Z709MICROCIRCUIT/REG SW- 1.26-2.5V +/-1.2% 20ARYT 113 6175/1 Z710MICROCIRCUIT/PWM CURR.-M 5.0V +/-1.5% 1MHzRYT 113 6053/4 Open EXHIBIT 104 (22) Prepared (also subject responsible if other)No. ERA/RKF/VR Larry LindströmB5KAKRC1311004-2 ApprovedCheckedDateRevReference KI/ERA/RKF/VR (L Lindström)2002-09-13A Z711MICROCIRCUIT/PWM CURR.-M 5.0V +/-1.5% 1MHzRYT 113 6053/4 Z712MICROCIRCUIT/VOLTAGE REG, INVERTING, -5VRYT 113 256/C Z851MICROCIRCUIT/COMP x2 36VRYT 101 6169/1 Z853MICROCIRCUIT/COMP x2 36VRYT 101 6169/1 Z854MICROCIRCUIT/COMP x2 36VRYT 101 6169/1 Z855MICROCIRCUIT/COMP x2 36VRYT 101 6169/1 Z856MICROCIRCUIT/SUP.V 2.93V L/NIN RESETRYT 113 6166/2 Z857MICROCIRCUIT/COMP x2 36VRYT 101 6169/1 Z858MICROCIRCUIT/MOSFET DRIVERx2 INV/NONINV /44RYT 109 6204/1 Z859MICROCIRCUIT/MOSFET D…

Text truncated - open the document above for the full version.

SP Sveriges Provnings- och Forskningsinstitut, Box 857, 501 15 BORÅS, Tel 033-16 50 00, Telefax 033-13 55 02, E-mail [email protected], Org.nr 556464-6874 SP Swedish National Testing and Research Institute, Box 857, S-501 15 BORÅS, SWEDEN, Telephone + 46 33 16 50 00, Telefax + 46 33 13 55 02, E-mail [email protected], Reg.No 556464-6874 Laboratorium ackrediteras av Styrelsen för ackreditering och teknisk kontroll (SWEDAC) enligt lag. Verksamheten vid de svenska ackrediterade laboratorierna uppfyller kraven enligt SS-EN 45001 (1989), SS-EN 45002 (1989) och ISO/IEC Guide 25 (1990:E). Denna rapport får endast återges i sin helhet, om inte SWEDAC och SP i förväg skriftligen godkänt annat. Laboratories are accredited by the Swedish Board for Accreditation and Conformity Assessment (SWEDAC) under the terms of the Act. The Swedish accredited laboratories meet the requirements set up in SS-EN 45001 (1989), SS-EN 45002 (1989) and ISO/IEC Guide 25 (1990:E). This report may not be reproduced other than in full, except with the prior written approval of SWEDAC and SP. REPORT issued by an FCC listed Laboratory Reg. no. 93866 The test site complies with RSS 212, Issue 1, Industry Canada file no. :IC 3482. 1002 ERICSSON AB Larry Lindström Färögatan 2, Kista 164 80 STOCKHOLM Handläggare, enhet/Handled by, department Datum/Date Beteckning/Reference Sida/Page Fredrik Isaksson 2002-09-11 F211633-F24 1(2) Electronics Tel +46 (0) 33 16 55 80 Equipment Authorization measurements on GSM Base station 1900 MHz with FCC ID: B5KAKRC1311004-2 (10 enclosures) Test object Transceiver Unit dTRU-19 EDGE, KRC 131 1004/2, R1B Summary Standard Compliant Enclosure Remarks FCC CFR 47 2.1046 RF Power output Yes 2 2.1047 Modulation characteristics Yes 3 2.1049 Occupied bandwidth Yes 4 Note 1 2.1051 Spurious emission at antenna Yes 5 2.1053 Field strength of spurious radiation Yes 6 2.1055 Frequency stability Yes 7 Intermodulation test Yes 8 Note 1: In GMSK mode this unit must use reduced transmit power with 14 dB, to 30.5 dBm, for the channels adjacent to each frequency block edge in order to comply. In EDGE mode the channels adjacent to each frequency block edge must be excluded in order to comply. It is not relevant to test TCC with output power below 44 dBm, thus no measurements were performed at the channels 512 and 810 with TCC. REPORT Datum/Date Beteckning/Reference Sida/Page 2002-09-11 F211633-F24 1 (2) FCC ID: B5KAKRC1311004-2 Encl. 1 Sign:..... Description - Equipment Under Test (EUT) Equipment: GSM Base station transceiver 1900MHz Tx Frequency range: 1930.2-1989.8 MHz Tested Channels: Radiated measurements: GMSK Mode 512: 1930.2 MHz dTRU with internal combiner plus TCC 537: 1935.2 MHz dTRU with internal combiner 562: 1940.2 MHz dTRU with internal combiner 660: 1959.8 MHz dTRU without internal combiner 685: 1964.8 MHz dTRU without internal combiner 760: 1979.8 MHz dTRU with internal combiner 785: 1984.8 MHz dTRU with internal combiner 810: 1989.8 MHz dTRU with internal combiner plus TCC EDGE mode 512: 1930.2 MHz 537: 1935.2 MHz 785: 1984.8 MHz 810: 1989.8 MHz One mode tested at a time: with internal combiner, without internal combiner and with internal combiner plus TCC Conducted measurements: 512: 1930.2 MHz 513: 1930.4 MHz 661: 1960.0 MHz 809: 1989.6 MHz 810: 1989.8 MHz Product number: dTRU-19 EDGE: KRC 131 1004/2 Serial number: See Hardware list in enclosure 9 Two dTRU were used during RF conducted measurements, dTRU-19 EDGE: KRC 131 1004/2, R1B, with s/n: AE5000HQSX and s/n AE5000HQT1 All RF conducted measurements were done at the output connectors of CDU-G. CDU-G19: BFL 119 153/1, R5B, s/n: A40003XCDW Manufacturer’s representative: Larry Lindström, Ericsson AB Purpose of test The purpose of the tests is to verify compliance to the performance characteristics specified in FCC CFR47. Reservation The test results in this report apply only to the particular Equipment Under Test (EUT) as declared in the report. REPORT Datum/Date Beteckning/Reference Sida/Page 2002-09-11 F211633-F24 2 (2) FCC ID: B5KAKRC1311004-2 Encl. 1 Sign:..... Delivery of test object The test object was delivered: 2002-08-19 Test engineers Fredrik Isaksson Peter Grahn Jonas Bremholt Test witness Larry Lindström, Ericsson AB (partly present) REPORT Datum/Date Beteckning/Reference Sida/Page 2002-09-24 F211633-F24 1 (4) FCC ID: B5KAKRC1311004-2 Encl. 2 Sign:..... RF Power output measurements according to 47CFR 2.1046 Date 2002-09-11 Temperature 22 °C ± 3 °C Humidity 49 % ± 5 % Test set-up and Procedure The measurements were made per J-STD-007A Vol 1. Measurements were made at CDU-G output connectors. The output was connected to a Peak power analyzer via a 50 ohm attenuator. The RF power was measured with variation in supply voltage at the highest power level. Test was performed on 24 V DC supply voltage system. The transmitter was modulated with 270.8 kbs pseudorandom data during the measurements. Measurement equipment Calibration Due SP number Boonton RF Peak power meter/analyzer 2002-12 503 144 Boonton Power sensor 56518-S/4 2003-02 503 146 Multimeter Fluke 85 III 2003-09 503 418 Testo 610, Temperature and humidity meter 2002-11 502 658 Results Mode: GMSK dTRU, output 1+2 (TCC). Nominal power 24 V DC Rated output power level after CDU-G (maximum): 47 dBm Test conditions Transmitter power (dBm) Peak/Average Channel 512 Channel 661 Channel 810 T nom 22°C V nom 24 V DC 45.7/45.3 46.4/46.0 46.1/45.6 T nom 22°C V min 20.4 V DC 45.9/45.5 46.6//46.2 46.2/45.8 V max 27.6 V DC 45.7/45.3 46.5/46.0 46.1/45.6 Measurement uncertainty 0.5 dB dTRU, output 1, without internal combiner: Nominal power 24 V DC Rated output power level after CDU-G (maximum): 44.5 dBm Test conditions Transmitter power (dBm) Peak/Average Channel 512 Channel 661 Channel 810 T nom 22°C V nom 24 V DC 43.6/43.1 44.2/43.7 43.8/43.2 T nom 22°C V min 20.4 V DC 43.6/43.1 44.2/43.7 43.8/43.2 V max 27.6 V DC 43.6/43.1 44.2/43.7 43.8/43.2 Measurement uncertainty 0.5 dB REPORT Datum/Date Beteckning/Reference Si…

Text truncated - open the document above for the full version.