BBD3-2BH-AIRRF Power Amplifier

Mike Kuo Hi Mike, Pls see FCC response below, and pls issue grant ASAP. Thanks, Claire -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Wednesday, May 17, 2006 12:43 PM To: [email protected] Cc: [email protected]; [email protected]; [email protected] Subject: FCC ID:BBD3-2BH-AIR Mr. Landsperger, You are not required to notify the FAA in this case, pertaining to equipment ID-BBD3-2BH-AIR FCC authorization. The requirement, per FCC 47 CFR Part 87-147d, is to notify the FAA "only" in the case of equipment intended for "transmission" and in the aviation bands listed in Part 87-147(d) (3). Thanks, Annette Allender FAA/AJW-64 Ph-7x3893 From: Claire HoqueSent: Thu 5/18/2006 2:27 PM To: Mike Kuo Cc: Chuck Cowden; Julia Luke Subject: FAA response: FCC ID:BBD3-2BH-AIR, 05U3905, AN06T5645 Attachments:  

1 Mike Kuo From: Claire Hoque Sent: Wednesday, May 03, 2006 10:06 AM To: Mike Kuo Cc: Michael Heckrotte; Julia Luke; Thu Chan Subject: answer: 05U3905 TPL COMMUNICATIONS, FCC ID: BBD3-2BH-AIR, Assessment NO.: AN06T5645, Notice#1 Attachments: BBD3-2BH-AIR FAA Letter.pdf; OBW Input-output.pdf BBD3-2BH-AIR FAA Letter.pdf (6... OBW put-output.pdf (32 K Hi Mike, Here are the answers below. Question #1: Based upon 87.147 of FCC rules, for those equipment in seeking equipment authorization and operates in the frequency range of 108 - 137 MHz , must notify the FAA of the filing of a certification application. The letter of notification must be mailed to: FAA, Office of Spectrum Policy and Management, ASR¡V1, 800 Independence Ave., SW., Washington, DC 20591 prior to the filing of the application with the Commission. (1) The notification must describe the equipment, give the manufacturer's identification, antenna characteristics, rated output power, emission type and characteristics, the frequency or frequencies of operation, and essential receiver characteristics if protection is required. <answer> FCC letter is attached, client confirmed the letter was mailed to the above address in April. (2) The certification application must include a copy of the notification letter to the FAA. The Commission will not act until it receives the FAA's determination regarding whether it objects to the application for equipment authorization. The FAA should mail its determination to: Office of Engineering and Technology Laboratory, Authorization and Evaluation Division, 7435 Oakland Mills Rd., Columbia, MD 21046. The Commission will consider the FAA determination before taking final action on the application. <answer> we already informed client. Question #2: Occupied Bandwidth: Please submit an AM modulated input plots and output plots to show the effect on the occupied bandwidth. <answer> attached pls find OBW input & output plots. Thanks, Claire -----Original Message----- From: Mike Kuo Sent: Tuesday, April 25, 2006 12:27 AM To: Mike Kuo Subject: TPL COMMUNICATIONS, FCC ID: BBD3-2BH-AIR, Assessment NO.: AN06T5645, Notice#1 Question #1: Based upon 87.147 of FCC rules, for those equipment in seeking equipment authorization and operates in the frequency range of 108 - 137 MHz , must notify the FAA of the filing of a certification application. The letter of notification must be mailed to: FAA, Office of Spectrum Policy and Management, ASR¡V1, 800 Independence Ave., SW., Washington, DC 20591 prior to the filing of the application with the Commission. (1) The notification must describe the equipment, give the manufacturer's identification, antenna characteristics, rated output power, emission type and characteristics, the 2 frequency or frequencies of operation, and essential receiver characteristics if protection is required. (2) The certification application must include a copy of the notification letter to the FAA. The Commission will not act until it receives the FAA's determination regarding whether it objects to the application for equipment authorization. The FAA should mail its determination to: Office of Engineering and Technology Laboratory, Authorization and Evaluation Division, 7435 Oakland Mills Rd., Columbia, MD 21046. The Commission will consider the FAA determination before taking final action on the application. Question #2: Occupied Bandwidth: Please submit an AM modulated input plots and output plots to show the effect on the occupied bandwidth. Best Regards Mike Kuo The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

FCC CFR47 PART 87 CERTIFICATION TEST REPORT FOR RF POWER AMPLIFIER MODEL NUMBER: PA3-2BH-AIR FCC ID: BBD3-2BH-AIR REPORT NUMBER: 05U3905-1 ISSUE DATE: JANUARY 26, 2006 Prepared for TPL COMMUNICATION 3370 SAN FERNANDO ROAD, SUITE 206 LOS ANGELES, CA 90065, USA Prepared by COMPLIANCE ENGINEERING SERVICES, INC. d.b.a. COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 2 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By A 1/26/06 Initial Issue Thu REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 3 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.3. WORST-CASE CONFIGURATION AND MODE......................................................................... 6 5.4. DESCRIPTION OF TEST SETUP ................................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ................................................................................ 9 7. LIMITS AND RESULTS ................................................................................................................. 10 7.1. RF OUTPUT POWER CONDUCTED ....................................................................................... 10 7.1.1. RF OUTPUT POWER AT NOMINAL AC MAINS VOLTAGE...................................... 10 7.1.2. RF OUTPUT POWER AT EXTREME AC MAINS VOLTAGES ................................... 12 7.2. MODULATION CHARACTERISTICS........................................................................................ 13 7.3. OCCUPIED BANDWIDTH ........................................................................................................ 13 7.4. FREQUENCY STABILITY .......................................................................................................... 13 7.5. SPURIOUS EMISSION AT ANTENNA TERMINAL................................................................... 14 7.6. FIELD STRENGTH OF SPURIOUS RADIATION..................................................................... 15 8. SETUP PHOTOS .............................................................................................................................. 16 REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 4 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: TPL COMMUNICATION 3370 SAN FERNANDO ROAD, SUITE 206 LOS ANGELES, CA 90065 USA EUT DESCRIPTION: RF POWER AMPLIFIER MODEL: PA3-3BH-AIR SERIAL NUMBER: CCS 01660 DATE TESTED: JANUARY 18 - 19, 2006 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 87 NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. Approved & Released For CCS By: Tested By: THU CHAN CHIN PANG EMC SUPERVISOR EMC ENGINEER COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 5 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 2. TEST METHODOLOGY The tests documented in this report were perform…

Text truncated - open the document above for the full version.

REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 16 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 17 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO REPORT NO: 05U3905-1 DATE: JANUARY 26, 2006 EUT: RF POWER AMPLIFIER FCC ID: BBD3-2BH-AIR Page 18 of 18 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. END OF REPORT RADIATED BACK PHOTO