BBD4-1AE-MASRF Amplifier

FCC ID: BBD4-1AE-MAS 34 2.1033 (C) (12) Equipment Photographs - External Photo 5 Detail View – External – Front FCC ID: BBD4-1AE-MAS 35 2.1033 (C) (12) Equipment Photographs - External Photo 6 Detail View – External – Left Side FCC ID: BBD4-1AE-MAS 36 2.1033 (C) (12) Equipment Photographs - External Photo 7 Detail View – External - Rear FCC ID: BBD4-1AE-MAS 37 2.1033 (C) (12) Equipment Photographs - External Photo 8 Detail View – External – Right Side FCC ID: BBD4-1AE-MAS 38 2.1033 (C) (12) Equipment Photographs - External Photo 9 Detail View – External - Top FCC ID: BBD4-1AE-MAS 39 2.1033 (C) (12) Equipment Photographs - External Photo 10 Detail View – External - Bottom

FCC ID: BBD4-1AE-MAS 30 2.1033 (C) (12) Equipment Photographs - Internal Photo 1 Detail View – Internal – Component Side of PCB FCC ID: BBD4-1AE-MAS 31 2.1033 (C) (12) Equipment Photographs - Internal Photo 2 Detail View – Internal – Component Side of PCB – Close Up FCC ID: BBD4-1AE-MAS 32 2.1033 (C) (12) Equipment Photographs - Internal Photo 3 Detail View – Internal – Circuit Side of PCB FCC ID: BBD4-1AE-MAS 33 2.1033 (C) (12) Equipment Photographs - Internal Photo 4 Detail View – Internal – Circuit Side of PCB – Close Up

FCC ID: BBD4-1AE-MAS 1 Application for Certification For an RF Power Amplifier TPL Communications 3370 San Fernando Road, Suite 206 Los Angeles, CA 90065 RF Power Amplifier: Part # PA4-1AE-MAS FCC ID: BBD4-1AE-MAS REPORT # RV38004J This report was prepared in accordance with the requirements of the FCC Rules and Regulations Part 2, Subpart J, 2.1031 through 2.1057, and Part 90 and other applicable sections of the rules as indicated herein. Prepared By: C. L. Payne III DNB Engineering, Inc. 5969 Robinson Avenue Riverside, Ca 92503-8620 4 June 2003 FCC ID: BBD4-1AE-MAS 2 TABLE OF CONTENTS Section Title Sheet # 1.0 ADMINISTRATIVE DATA 3 1.1 Certifications and Qualifications 3 1.2 Measurements and Repeatability Information 3 Note: Paragraph numbers in this report follow the application section numbers found in the FEDERAL COMMUNICATIONS COMMISSION Rules and Regulations, Part 2, Subpart J for Certification of electronic equipment. 2.1033 (C) (1) Application for Certification 4 2.1033 (C) (2) FCC Identifier 5 2.1033 (C) (3) Installation and Operating Instructions (Service manual) 6-20 2.1033 (C) (4) Type of Emissions 21 2.1033 (C) (5) Frequency Range 22 2.1033 (C) (6) Operating Power 23 2.1033 (C) (7) Maximum Power Allowed in Applicable part(s) of the Rules 24 2.1033 (C) (8) Final RF Amplifier Input Power Characteristics 25 2.1033 (C) (9) Tune Up Procedure 26 2.1033 (C) (10) Schematic Diagram and Circuit Description 27-28 2.1033 (C) (11) Equipment Identification Plate 29 2.1033 (C) (12) Equipment Photographs (Internal) 30-33 2.1033 (C) (12) Equipment Photographs (External) 34-39 2.1033 (C) (13) Digital Modulation Techniques 40 2.1033 (C) (14) Test Data 41 Test Set-Up 42-43 2.1046 Measurement of RF Power Output 44-45 2.1049 Measurement of Occupied Bandwidth 46-47 2.1051 Spurious Emissions at Antenna Terminals 48-49 2.1053 Measurement of Field Strength of Spurious Radiation 50-51 2.1055 Measurement of Frequency Stability 52 2.1057 Frequency Spectrum to be Investigated 53 RF Exposure 54 Test Equipment Log 55 FCC ID: BBD4-1AE-MAS 3 1.0 ADMINISTRATIVE DATA 1.1 Certifications and Qualifications I certify that DNB Engineering, Inc conducted the tests performed in order to obtain the technical data presented in this application. Also, based on the results of the enclosed data, I have concluded that the equipment tested meets or exceeds the requirements of the Rules and Regulations governing this application. 1.2 Measurement Repeatability Information The test data presented in this report has been acquired using the guidelines set forth in FCC Part 2.1031 through 2.1057, and Part 90. The test results presented in this document are valid only for the equipment identified herein under the test conditions described. Repeatability of these test results will only be achieved with identical measurement conditions. These conditions include: The same test distance, EUT Height, Measurement Site Characteristics, and the same EUT System Components. The system must have the same Interconnecting Cables arranged in identical placement to that in the test set-up, with the system and/or EUT functioning in the identical mode of operation (i.e. software and so on) as on the date of the test. Any deviation from the test conditions and the environment on the date of the test may result in measurement repeatability difficulties. All changes made to the EUT during the course of testing as identified in this test report must be incorporated into the EUT or identical models to ensure compliance with the FCC regulations. C. L. Payne III (Para. 1.1) Manager, Commercial Products. DNB Engineering, Inc. Tel. (909) 637-2630 Fax (909) 637-2704 E-mail [email protected] FCC ID: BBD4-1AE-MAS 4 2.1033 (C) (1) Application for Certification Name of Applicant: TPL Communications 3370 San Fernando Road, Suite 206 Los Angeles, Ca 90065 FRN: 0008271447 Applicant is: X Manufacturer Vendor Licensee Prospective Licensee Other Name of Manufacturer TPL Communications Description: RF Power Amplifier Part Number: PA4-1AE-MAS Anticipated Production Quantity: Multiple Units Applicable FCC Parts: 90 FCC ID No: BBD4-1AE-MAS FCC Emissions Designator: F3E Frequency Range: 210-235 MHz Rated Output Power: 70-100W FCC ID: BBD4-1AE-MAS 5 2.1033 (C) (2) FCC Identifier FCC ID: BBD4-1AE-MAS FCC ID: BBD4-1AE-MAS 22 2.1033 (C) (5) Frequency Range 210-235MHz (Factory set for 220MHz) FCC ID: BBD4-1AE-MAS 23 2.1033 (C) (6) Operating Power 70 - 100 Watts FCC ID: BBD4-1AE-MAS 24 2.1033 (C) (7) Maximum Power Allowed in Applicable Part(s) of the Rules RULES PART MAXIMUM POWER (WATTS) Part 90.205(q) 120 FCC ID: BBD4-1AE-MAS 29 2.1033 (C) (11) Equipment Identification Plate NOTES: Label will be constructed of 0.02 inch aluminum as shown on the equipment with permanent adhesive. All information on the label will be etched or stamped. Both methods will exceed the expected lifetime of the equipment. The label will be large enough to allow all information to be legible. FCC ID: BBD4-1AE-MAS 30 2.1033 (C) (12) Equipment Photographs - Internal Photo 1 Detail View – Internal – Component Side of PCB FCC ID: BBD4-1AE-MAS 31 2.1033 (C) (12) Equipment Photographs - Internal Photo 2 Detail View – Internal – Component Side of PCB – Close Up FCC ID: BBD4-1AE-MAS 32 2.1033 (C) (12) Equipment Photographs - Internal Photo 3 Detail View – Internal – Circuit Side of PCB FCC ID: BBD4-1AE-MAS 33 2.1033 (C) (12) Equipment Photographs - Internal Photo 4 Detail View – Internal – Circuit Side of PCB – Close Up FCC ID: BBD4-1AE-MAS 34 2.1033 (C) (12) Equipment Photographs - External Photo 5 Detail View – External – Front FCC ID: BBD4-1AE-MAS 35 2.1033 (C) (12) Equipment Photographs - External Photo 6 Detail View – External – Left Side FCC ID: BBD4-1AE-MAS 36 2.1033 (C) (12) Equipment Photographs - External Photo 7 Detail View – External - Rear FCC ID: BBD4-1AE-MAS 37 2.1033 (C) (12) Equipment Photographs - External Photo 8 Detail View – External – Right Side FCC ID: BBD4-1AE-MAS 38 2.1033 (C) (12) …

Text truncated - open the document above for the full version.

TPL Communications FCC ID: BBD4-1AE-MAS Occupied Bandwidth, 4 kHz operation Input signal Output signal