BCR-MRB-LMRBand Selective RF Booster

MR Booster Manual Order No. MN001808-1 Issue 9/99 © Copyright 1999 Mikom All Rights Reserved Page - ii -MR Booster Manual (MN001808-1, 9/99) All rights reserved. No part of this publication, or any software included with it, may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, including photocopying, electronic, mechanical, recording, or otherwise, without prior written permission of the copyright holder. This document contains proprietary information of MIKOM. The contents are confidential and any disclosure to persons other than the officers, employees, agents, or subcontractors of the owner or licensee of this document, without prior written consent of MIKOM, is strictly prohibited. Field Support If you need technical assistance with the MR Booster contact MIKOM at: Technical Hotline: (800) 800-7465 or (804) 386-5360 MR Booster Manual (MN001808-1, 9/99)Page - iii - Safety Information The MR Booster equipment has been designed for maximum safety when installed, operated, and maintained according to the instructions in this manual. Do not bypass any of the safety features of this equipment or operate this equipment in an improper environment. All wiring external to the equipment should comply with the current edition of the Electrical Code or any national wiring rules that apply. Publication Notice The information in this document is subject to change without notice. MIKOM shall not be liable for technical or editorial errors or omissions that may occur in this document, or for incidental or consequential damages resulting from the furnishing, performance, or use of this document. Page - iv -MR Booster Manual (MN001808-1, 9/99) LIMITED WARRANTY MIKOM, a division of ALLEN TELECOM INC. ("ALLEN TELECOM"), warrants, on the terms and conditions hereto set forth, all products manufactured by it to be free under normal use and service from defects in materials and workmanship for a period of one (1) year from the date of shipment, to the first consumer (the "Warranty Period"). ALLEN TELECOM's obligation under this Warranty is limited to prompt repair or replacement of the product, at its option, without charge, at an authorized ALLEN TELECOM dealer or at the factory of ALLEN TELECOM in Cleveland, Ohio, when the product is returned to an authorized dealer or to the factory with all transportation charges prepaid and examination of the product shall disclose it to have been defective in the respects aforesaid during the Warranty Period. The Limited Warranty Period shall not be extended beyond its original term with respect to any part or parts repaired or replaced by ALLEN TELECOM hereunder. The Warranty Period shall not apply to any product which has been repaired or altered in any manner by anyone other than ALLEN TELECOM or an authorized outlet of ALLEN TELECOM, or if the defect, malfunction or failure of the was caused by damage by lightning, flood or other acts of nature or by power surges, or from unreasonable use, or from improper installation or application, or to any product which has not been maintained or used in accordance with the operating specifications set forth in ALLEN TELECOM's written instructions. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SPECIFIED ABOVE. UNDER NO CIRCUMSTANCES SHALL ALLEN TELECOM BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES FOR BREACH OF THIS WARRANTY OR OF ANY IMPLIED WARRANTY. ALLEN TELECOM neither assumes nor authorizes any person to assume for it any obligation or liability other than as herein expressly stated. MR Booster Manual (MN001808-1, 9/99)Page - v - Contents Page Section 1. Introduction........................................................................................1 1.1About This Manual........................................................................................................1 1.2Conventions Used in This Manual................................................................................2 1.3Terminology..................................................................................................................2 Section 2. System Description.............................................................................3 2.1Introduction...................................................................................................................3 2.2System Overview..........................................................................................................3 2.3Theory of Operation......................................................................................................5 2.3.1Downlink Path..................................................................................................5 2.3.2Uplink Path.......................................................................................................6 2.3.3System Control.................................................................................................6 2.4System Components......................................................................................................9 2.4.1Power Supply....................................................................................................9 2.4.2Downlink Power Amplifier..............................................................................9 2.4.3Logic Controller Board.....................................................................................9 2.4.4PA Combiner/Splitter Module........................................................................10 2.4.5Uplink Low Noise Amplifier..........................................................................10 2.4.6Duplexers........................................................................................................11 2.4.7RF Cable.........................................................................................................11 2.4.8Fan Assembly......................................…

Text truncated - open the document above for the full version.

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Authority to Act as Agent to the Federal Communications Commission On our behalf, I appoint MET Laboratories, Inc. to act as agent in the preparation of this application for equipment authorization to the Federal Communications Commission. I certify that submitted Exhibits properly describe the device or system for which equipment authorization is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Commission's regulations will have affixed to it a label identical to that submitted for approval with this application. Dated this__21___Day of_____March _____2000 Agency agreement expiration date: 06/09/00 By:_________________Howard Gianopulos Title: Engineering Program Manager Telephone: 1-804-386-5242 Applicant: Allen Telecom Systems

Q0156R7 A C:\WINDOWS\TEMP\Q0156R7A.docPage 1 of 2 Confidential: For Internal Use Only Development Specification for 8W DL Final Amplifier for MR801B/MR801Bi IssueChangeDateNameApproved AInitial Release01.10.99Leupold Q0156R7 A C:\WINDOWS\TEMP\Q0156R7A.docPage 2 of 2 ID: 151970 Final-Amp. for MR801B/MR801Bi DOWNLINK Frequency Range Downlink851 - 894Mhz Bandwidth43Mhz Nominal Gain at ambient (CF)31,5dB Gain Variation over Frequency+ 0,3dB Gain Variation over Temp.+ 2.0dB ICP3 Output49dBm min Psat39dBm typ. Return Loss Input15dB min Return Loss Output20dB min Nominal Impedance50 Ohm Current Consumption12,5V=2,2A + 0,2A Mech. Dwg.G0854Z1A Main DC-Connector Pin 1NC Pin 2NC Pin 3NC Pin 4NC Pin 5NC Pin 6NC Pin 7NC Pin 8NC Pin 9/10NC Pin 11/12GND 12V Connector Pin 112,5V Pin 212,5V Environmentol Specifications Operating Temperature RangeFrom -33° to +75°

FCC Equipment Authorization Application ExhibitAllen Telecom, Ltd. FCC ID:BCR-MRB-LMR Type of Exhibit:Statement Concerning RF Exposure FCC Rule Part:47CFR1.1307 Manufacturer:Allen Telecom, Inc. 140 Vista Centre Drive Forest , VA 24551 Model:MR Booster FCC ID(s):BCR-MRB-LMR Date:5/27/00 Per the FCC Rules and Regulations as described in OET Bulletin 65, this device is categorically excluded from routine evaluation because these are used at fixed installations with antennas mounted on outdoor, permanent structures and fall well below the power limits requiring RF evaluation in accordance with 47CFR1.1307. Certifying Engineer: Reviewing Engineer: Date: 5/27/00

April 21, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Attention:Applications Examiner Applicant:Allen Telecom, Inc. 140 Vista Centre Drive Forest , VA 24551 Equipment:MR Booster Model LMR 800 FCC ID: BCR-MRB-LMR Specification: 47 CFR 90 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Allen Telecom, Inc. for the Licensed Certification of their Model: LMR 800 MR Booster. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR 90, for a MR Booster. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey Director, EMC Laboratory MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE !! BALTIMORE, MARYLAND 21230-3432 !! PHONE (410) 354-3300 !! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT:MR Booster , Model LMR800 FCC ID:BCR-MRB-LMR Specification:47 CFR 90 On Behalf of the Applicant:Allen Telecom, Inc. 140 Vista Centre Drive Forest, VA 24551 Manufacturer:Allen Telecom, Inc. 140 Vista Centre Drive Forest, VA 24551 Manufacturer’s Mr. Howard Giannapolis Representative Test Date(s):January 13 through February 2, 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 90 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratory EMI1303- 3 -Feb. 2, 2000 1.0INTRODUCTION The following data is presented on behalf of the Applicant, Allen Telecom, Inc., as verification of the compliance of the Allen Telecom MR Booster, Model LMR 800 to the requirements of 47 CFR 90. 2.0TEST SITE All testing was conducted at MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 21230-3493. Radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/MET. 3.0TEST EQUIPMENT USED ManufacturerEquipment Calibration DueCal. Interval Hewlett Packard8563A Spectrum Analyzer1/29/01annual EMCOBiconical Antenna 31042/9/01annual EMCOEMCO Log Periodic Antenna3/20/00annual EMCODouble Ridge Guided Horn3/20/00annual Hewlett Packard8591E Analyzer08/12/00annual Hewlett PackardE4433B Digital Signal Gen. E4432A Digital Signal Gen. 09/02/2001 01/08/2002 annual SolarLISN6/30/00annual 4.0EQUIPMENT UNDER TEST CONFIGURATION The MR Booster was configured with an AC power supply module and a digital signal generator were used to simulate various TDMA/FM RF input signals to the EUT. The EUT with host external computer was configured for maximum signal gain and bandwidth. In addition, the EUT was operated in a manner representative of the typical usage of the equipment. During all testing, system components were manipulated within the confines of typical usage to maximize each emission. Emission Designator: AMP Four Configurations were tested and all data was recorded during testing. For the sake of simplicity only representative and/or worst case data is presented in this test report : 4 PA w/ 8 watt (4 power amplifiers with 8 watt drive) 4 PA w/o 8 watt (4 power amplifiers without 8 watt drive) 2 PA w/ 8 watt (2 power amplifiers with 8 watt drive) 2 PA w/o 8 watt (4 power amplifiers without 8 watt drive) 5.0TEST TYPE(S) 5.1Radiated Emissions: 47CFR2.1053, 90.210(h), and 90.691(a) 5.2Occupied Bandwidth: 47CFR2.1049 5.3RF Power Output: 47CFR 2.1046, 90.205(i), and 90.635 5.4Spurious Emission at Antenna Terminals:(downlink) 47CFR 2.1051, 90.210(h), 90.691(a) 5.5Emissions Masks: 47CFR90.210 5.6Intermodulations Spurious Emissions - 2 Tone Simultaneous RF Injection at low and high end of the Channel band: 47CFR2.1051, 90.210(h), and 90.691(a) 5.7Line conducted Emissions: 47CFR15.107(b) 6.0TEST RESULTS EMI1303- 4 -Feb. 2, 2000 E(V/m) 1m ' 49.2X31 1 E(V/m) 1m '39V/mor151.9dbμV 43%10Log(31)'57.91dB 151.9dBμV&57.91dB'93.91dBμV@1m E(V/m) 3m ' 49.2X31 3 E(V/m) 3m '13V/mor142.3dbμV 142.3&59.7'84.37dBμV@3m 6.1TEST TYPE: Radiated Emissions 6.1.1TECHNICAL SPECIFICATION:2.1053; 90.210(h); 90.691(a) 6.1.2TEST DATE(S):Feb 1 . 2000 6.1.3MEASUREMENT PROCEDURES: As required by §2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with a digital signal generator on and terminated. The frequency list from the preliminary measurements were used as a guide for making final measurements on an 10 meter open area test site. The unit was scanned over the frequency range of 9 kHz to 9 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an input power (as measured at the output of the Amplifier) of 31 watts: P o = 31 W As per 2.993 (a), it is assumed this power is to be fed to a half-wave tuned dipole. Using a conversion formula for distance, the field strength at one meter can be derived: As per 90.691(a), the spurious emissions must be attenuated by 43 + log(P) which is: Therefore, the limit for spurious emissions is: At 3 meters measurement distance, the limit is; Again, according to 90.691, all signals must be attenuated by 46.01 dB; Therefore, the limit for spuri…

Text truncated - open the document above for the full version.