BEJL4200AL42" LCD Monitor

APPENDIX F : FCC ID : BEJL4200AL USER’S MANUAL 1 FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. CE Conformity Notice(for Europe) Products with the “CE” Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms : • EN 55022:1998 ; Radio Frequency Interference • EN 55024:1998 ; Electromagnetic Immunity • EN 61000-3-2 ; Power Line Harmonics • EN 61000-3-3 ; Voltage Fluctuations • EN 60950 ; Product Safety Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO95 Congratulations! You have just purchased a TCO’95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem as far as computers and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic- and climatic-influencing emissions, radioactive waste, etc.), it is vital to conserve energy. Electronic equipment in offices consumes as enormous amount of energy, since it is often routinely left running continuously. What does the environmenal labelling involve? This product meets the requirements for the TCO’95 Regulatory Information NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. 2 Regulatory Information cont. NUTEK Naturskydds föreningen Närings- och teknikutvecklingsverket SEMKO scheme, which provides for international environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturckyddsföreningen (The Swedish Society for Nature Conservation), and NUTEK (The National Board for Industrial and Technical Development in Sweden), and SEMKO AB (an international certification agency). The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern, among other things, restriction on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product must be prepared for recycling, and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example…

Text truncated - open the document above for the full version.

Attn.: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: CONFIDENTIALITY REQUEST FOR 42” LCD Monitor FCC ID: BEJL4200AL MODEL #: L4200AL Gentlemen This letter serves as an official request for confidentiality under FCC Rule Section 0.459. We have requested that the block diagrams required to be submitted with this application be withheld from public review. These documents contain detailed system and equipment description and related information about the product which LG Electronics Inc. considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, LG Electronics Inc. feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Kyeom Soon Kim January 28, 2003 LG Electronics Inc./General Manager LG Electronics Inc.

FCC ID : BEJL4200AL APPENDIX E 1. External View 2. Internal View 3. PCB View 3-1. Main Board 3-2. PC Audio Board 3-3. Power-Inverter(LIPS – KN Powertek, SAMSUNG) Board 3-4. Component(AV,S-video,Y Pb Pr) Board 3-5. Control Board EUT Photographs FCC ID : BEJL4200AL 1. External View [ LCD Monitor Front ] [LCD Monitor Back ] FCC ID : BEJL4200AL 2. Internal View FCC ID : BEJL4200AL 2. Internal View-LCD Module FCC ID : BEJL4200AL 3-1. Main Board FCC ID : BEJL4200AL 3-2. PC Audio Board FCC ID : BEJL4200AL 3-3. Power-Inverter Board(LIPS - KN Powertek ) FCC ID : BEJL4200AL 3-3. Power-Inverter Board(LIPS - SAMSUNG) FCC ID : BEJL4200AL 3-4. Component(AV,S-video,Y Pb Pr) Board FCC ID : BEJL4200AL 3-5. Control Board

FCC ID : BEJL4200AL APPENDIX G : Specification FCC ID : BEJL4200AL 1600 X 1200Max. Resolution8 37.25 kgWeight (Max.)10 125.90 X 69.70 X 29.45 (Cm) Dimension (W X H X D) (Max.)9 < 300WPower Consumption7 AC 100-240 V, 50/60 Hz, 2.8 ARating6 BEJL4200ALFCC ID5 L4200ALModel Number4 LGTrade Name3 42” LCD MonitorEquipment Name2 FCC Part 15, Class BEquipment Class1

1/17 Report No.: 00431-4521-F4016 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 LG Electronics Inc. Quality & Reliability Center 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul 150-096, Korea Tel: + 82 2 2630 3077~9, Fax: +82 2 2635 5543 CERTIFICATION OF COMPLIANCE Date of Issue: January 27, 2004 Test Report No: 00431-4521-F4016 Applicant: LG Electronics Inc. Regulation: FCC Part 15 Class B / Canada Standard ICES-003 Class B Test procedure: ANSI C63.4-1992 / Canada Standard ICES-003 Equipment Class: Unintentional Radiators – Digital device EUT Type: 42”LCD Monitor Trade Name(s): Model No.: LG L4200AL This device has been verified to comply with the applicable requirements in the FCC Part 15 / Canada Standard ICES-003 and was tested in accordance with the measurement procedures specified in ANSI C63.4-1992 / Canada Standard ICES-003. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Kyeom-Soon Kim / General Manager Quality and Reliability Center LG Electronics Inc. 2/17 Report No.: 00431-4521-F4016 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 REPORT FOR A DIGITAL DEVICE Scope - Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. U.S. Responsible Party: Address: LG Electronics USA Inc. 6133 North River Road, Suite 1100 (Riverway Plasza) Rosemont, IL 60018, USA Contact Person: P. H. Byun, General Manager Telephone No.: (847) 692-4630 EXT.329 Manufacturer: LG Electronics Inc. DID Division Address: 642 Jinpyoung-dong Kumi-City Kyoungsangbuk-do, 730-360, Korea FCC ID No.: BEJL4200AL EUT Class: Unintentional Radiators - Digital device EUT Type: 42”LCD Monitor Trade Name: LG Model No.: L4200AL Rule Part: FCC Part 15 Class B / Canada Standard ICES-003 Class B Test Procedure: ANSI C63.4-1992 / Canada Standard ICES-003 Date of Test: January 07~08, 2004 Date of Receipt of EUT: January 05, 2004 Date of Issue: January 27, 2004 Test Report No.: 00431-4521-F4016 Test Result: Positive Quality and Reliability Center authorizes the above-named applicant to reproduce this report provided it is reproduced in its entirety. Quality and Reliability Center reports apply only to the specific samples tested under stated test conditions. It is the manufacturer’s responsibility to assure that additional production unit of this model are manufactured with identical electrical and mechanical components. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. The Quality and Reliability Center was accredited by National Voluntary Laboratory Accreditation Program for the specific scope of accreditation under Lab Code: 200040-0. Tested by: Reviewed by : K. C. Paek / Research Engineer Quality and Reliability Center LG Electronics Inc. D. H. Lee / Senior Research Engineer Quality and Reliability Center LG Electronics Inc. 3/17 Report No.: 00431-4521-F4016 LG Electronics Inc. Q & R Center, 36, Munlae-dong, 6-ga, Youngdungpo-gu, Seoul, Korea Tel:+82-2-2630-3077~9, Fax:+82-2-2635-5543 CONTENTS Page 1. GENERAL INFORMATION .....................................................................................................................4 1.1 D ESCRIPTIONS OF EQUIPMENT UNDER TEST (EUT) ...................................................................................4 1.2 R EGULATIONS APPLIED TO EUT ...............................................................................................................4 1.3 M EASUREMENT PROCEDURE.....................................................................................................................5 1.4 M EASUREMENT PLACE..............................................................................................................................5 2. GENERAL TEST CONDITIONS ..............................................................................................................6 2.1 O PERATING CONDITIONS OF EUT .............................................................................................................6 2.2 S TABILIZATION OF EUT OPERATING.........................................................................................................6 2.3 T EMPERATURE AND HUMIDITY.................................................................................................................6 3. TEST SITE....................................................................................................................................................6 3.1 S EMI-ANECHOIC CHAMBER.......................................................................................................................6 3.2 A SHIELDED ENCLOSURE...........................................................................................................................6 4. CALIBRATIONS OF MEASURING INSTRUMENTS...........................................................................6 5. DESCRIPTION OF TEST CONDITION ..................................................................................................7 5.1 P OWER LINE CONDUCTED EMISSION MEASUREMENTS...............................................................................7 5.2 R ADIATED EMISSIONS MEASUREMENTS.....................................................................................................8 6. MEASURING INSTRUMENTS AND SET-UP .......................................................................…

Text truncated - open the document above for the full version.

FCC ID : BEJL4200AL 3. Radiated Emissions(KN Powertek) 3.1 D-SUB : Analog mode (Hor) FCC ID : BEJL4200AL 3.1 D-SUB : Analog mode (Ver) FCC ID : BEJL4200AL 3.2 DVI-D : Digital mode (Hor) FCC ID : BEJL4200AL 3.2 DVI-D : Digital mode (Ver) FCC ID : BEJL4200AL 3.3 AV mode (Hor) FCC ID : BEJL4200AL 3.3 AV mode (Ver) FCC ID : BEJL4200AL 3.4 S-video mode (Hor) FCC ID : BEJL4200AL 3.4 S-video mode (Ver) FCC ID : BEJL4200AL 3.5 Component mode (Hor) FCC ID : BEJL4200AL 3.5 Component mode (Ver) FCC ID : BEJL4200AL 4. Conducted Emissions(KN Powertek) 4.1 D-SUB : Analog mode FCC ID : BEJL4200AL 4.2 DVI-D : Digital mode FCC ID : BEJL4200AL 4.3 AV mode FCC ID : BEJL4200AL 4.4 S-video mode FCC ID : BEJL4200AL 4.5 Component mode

FCC ID : BEJL4200AL APPENDIX A : Test Graph 1. Radiated Emission(SAMSUNG) 1.1 D-SUB : Analog mode 1.2 DVI-D : Digital mode 1.3 AV mode 1.4 S-Video mode 1.5 Component mode 2. Conducted Emissions (SAMSUNG) 2.1 D-SUB : Analog mode 2.2 DVI-D : Digital mode 2.3 AV mode 2.4 S-Video mode 2.5 Component mode 3. Radiated Emission(KN Powertek) 3.1 D-SUB : Analog mode 3.2 DVI-D : Digital mode 3.3 AV mode 3.4 S-Video mode 3.5 Component mode 4. Conducted Emissions (KN Powertek) 4.1 D-SUB : Analog mode 4.2 DVI-D : Digital mode 4.3 AV mode 4.4 S-Video mode 4.5 Component mode FCC ID : BEJL4200AL 1. Radiated Emissions(SAMSUNG) 1.1 D-SUB : Analog mode (Hor) FCC ID : BEJL4200AL 1.1 D-SUB : Analog mode (Ver) FCC ID : BEJL4200AL 1.2 DVI-D : Digital mode (Hor) FCC ID : BEJL4200AL 1.2 DVI-D : Digital mode (Ver) FCC ID : BEJL4200AL 1.3 AV mode (Hor) FCC ID : BEJL4200AL 1.3 AV mode (Ver) FCC ID : BEJL4200AL 1.4 S-video mode (Hor) FCC ID : BEJL4200AL 1.4 S-video mode (Ver) FCC ID : BEJL4200AL 1.5 Component mode (Hor) FCC ID : BEJL4200AL 1.5 Component mode (Ver) FCC ID : BEJL4200AL 2. Conducted Emissions(SAMSUNG) 2.1 D-SUB : Analog mode FCC ID : BEJL4200AL 2.2 DVI-D : Digital mode FCC ID : BEJL4200AL 2.3 AV mode FCC ID : BEJL4200AL 2.4 S-video mode FCC ID : BEJL4200AL 2.5 Component mode

FCC ID : BEJL4200AL APPENDIX D : 1. Radiated Emission 2. Conducted Emission Test Set-up Photographs FCC ID : BEJL4200AL 1. Radiated Emission FCC ID : BEJL4200AL 2. Conducted Emission