BJ4-WLTX205Wireless Door Chime Transmitter

DRAFT COPY THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this add on wireless door sensor. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay! USE AND CARE GUIDE ADD ON WIRELESS DOOR SENSOR Illustrations may vary from actual unit. Safety Information 1. Please read and understand this entire manual before attempting to assemble, install, or operate this sensor. WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near batteries. If battery is swallowed, immediately notify a doctor.NOTE: The range of the wireless doorbell can vary with location, temperature, and battery condition. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.Care and Cleaning  Use a dry cloth to clean the entry alert.  Do not use cleaners or polishes.  Do not use any fluids on the entry alert. Pre-InstallationTOOLS REQUIRED Phillips screwdriver Small flathead screwdriver Drill 1/16” (1.5 mm) drill bit Safety goggles HARDWARE INCLUDED Part Description Quantity AA Jumper 1 BB Screw - small 4 CC Screw - large 2 DD Double-sided tape 1 PACKAGE CONTENTS Part Description Quantity A Sensor (with preinstalled battery) 1 B Magnet 2 C Spacer 2 Installation 1 Removing the battery tab   Remove the back of the sensor (A) by pushing in the tab on the bottom with a small screwdriver (not included).   Remove the orange battery tab from the sensor (A). 2 Syncing the push button and doorbell   Press and hold the “SYNC” button on the doorbell until the doorbell sounds a “Beep-Beep”.   Press the button inside the sensor (A) within 30 seconds of pressing the doorbell “SYNC” button.   Press the button inside the sensor again to activate the doorbell and ensure the sensor (A) and doorbell are synced. CR2032 SYNC – PRESSAND RELEASE . RESET – HOLD 10 SECONDS. TUNE – HOLD 1 SECOND. 30 3 Testing the sensor and doorbell   Temporarily position the sensor (A) and magnet (B) where they will be mounted.   Move the magnet (B) away from the sensor (A) to simulate a door being opened. The red LED should flash and the doorbell will sound “Beep-Beep”.   If the doorbell does not sound, move the doorbell closer to the sensor (A) and test again. NOTE: Do not permanently mount the sensor until the sensor and doorbell are working properly. SYNC – PRESSAND RELEASE . RESET – HOLD 10 SECONDS. C H I M E V O L U M E TUNE – HOLD 1 SECOND. UP FRONT TRANS REAR TYPE “C” TYPE “C” TYPE “C” 4 Preparing to mount the sensor The maximum gap between the sensor (A) and the magnet (B) is 1/2 in.. The arrows on the face of each component must be aligned and facing each other.   Place the sensor (A) on the door frame and the magnet (B) beside the sensor (A) and ensure the arrows are aligned.   If the magnet (B) is recessed, use the spacer (C) to ensure proper alignment. 1/2" Maximum Warranty3-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 3 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com. Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-844-760-3644 HAMPTONBAY.COM Installation 5 Mounting the sensor Use either the small screws (BB) or double-sided tape (DD) to mount the sensor (A).   To mount with the small screws (BB), remove the back of sensor (A) by pushing in the tab on the bottom with a small screwdriver. Place the sensor (A) back against the mounting surface and mark the two screw holes. Drill two 1/16 in. pilot holes. Attach the sensor (A) back with the small screws (BB). Tighten securely and snap on the front of the sensor (A).   When attaching the sensor (A) with double-sided tape (DD), remove paper from both sides of the double-sided tape (DD) and apply to a clean surface. 6 Mounting the magnet Use the small screws (BB) (or the large screws (CC) if using the magnet spacer (C)) to mount the magnet (B).   Remove the back of magnet (B) by pushing in the tab on the bottom of the magnet (B) with a small screwdriver.   Place the magnet (B) back against the mounting surface and mark the two screw holes.   D rill two 1/16 in. pilot holes.   Attach the magnet (B) back with the small screws (BB). Tighten securely and snap on the front of the magnet (B). Specifications Power requirements Type 2032 3V battery (included) Troubleshooting Problem Solution The doorbell does not sound. Make sure batteries are installed according to the diagram inside the sensor and doorbell (if applicable).Check the charge of the sensor and doorbell batteries (if applicable) and replace if necessary.Make sure the plug-in doorbell has power (if appl…

Text truncated - open the document above for the full version.

LETTER OF AGENCY To Whom It May Concern: “I, an officer of HeathCo LLC. do hereby authorize Intertek Testing Services (Mr. Terry Chan / Koo Wai Ip / Kenneth Wong) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules until further notice. “ I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862 Company Name: HeathCo LLC. Contact Person Name: Jeff Bessinger. Title: Associate Engineer. Phone: 270-846-8271. Fax: 270-846-8501. e-mail: [email protected]. Signature: Date: June 3 rd , 2015.

INTERTEK TESTING SERVICE Report No.: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Equipment Photographs Model : WLTX-205 (External)

BATTERY 1 X A23 UP MODEL: WLTX-205 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 HAMPTON BAY ATLANTA, GA MADE IN CHINA

INTERTEK TESTING SERVICE Report No.: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Equipment Photographs Model : WLTX-205 (Internal) INTERTEK TESTING SERVICE Report No.: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Equipment Photographs Model : WLTX-205 (Internal) INTERTEK TESTING SERVICE Report No.: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Equipment Photographs Model : WLTX-205 (Internal) INTERTEK TESTING SERVICE Report No.: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Equipment Photographs Model : WLTX-205 (Internal)

Analysis Report The equipment under test (EUT) is a transmitter for remote doorbell operating at 315MHz which is operated by a crystal. The EUT is powered by a 3VDC Lithium button cell battery. The EUT contains a “SYNC” button and a magnet sensor. The transmitter will be activated and then send transmit a signal to doorbell while the magnet is moving away from the magnet sensor (i.e. simulate the door being opened). The “SYNC” button is used for the setup between the transmitter and the doorbell. For the magnet sensor portion, the transmitter will cease transmission within 5 seconds after activation. For the “SYNC” button, the manually operated transmitter will automatically deactivate the transmitter within not more than 5 seconds of being released. Antenna Type: Internal antenna Antenna Gain: 0dBi Nominal rated field strength: 74.9 dBμV/m at 3m Maximum allowed field strength of production tolerance: +/- 3dB According to the KDB 447498: Based on the Maximum allowed field strength of production tolerance was 77.9dBμV/m at 3m in frequency 315MHz, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 0.018mW Conducted power = Radiated Power (EIRP) – Antenna Gain So; Conducted Power =0.018mW. The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (0.315) mW = 26.7 mW Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

- Intertek's standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report No.: 15050668HKG-002 HeathCo LLC Application For Certification (Original Grant) (FCC ID: BJ4-WLTX205) (IC: 3984A-WLTX205) Transmitter Prepared and Checked by: Approved by: Signed On File Leung Sung Tak, Andy Assistant Engineer Wong Kwok Yeung, Kenneth Lead Engineer Date: June 22, 2015 INTERTEK TESTING SERVICES Report No.: 15050668HKG-002 i FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 GENERAL INFORMATION FCC Grantee: HeathCo LLC FCC Grantee Address: 2445 Nashville Road, Bowling Green, Kentucky 42101, United States. IC Grantee: HeathCo LLC IC Grantee Address: 2445 Nashville Road, Bowling Green, KY 42102, USA. Contact Person: Jeff Bessinger Tel: 270-846-8271 Fax: 270-846-8501 e-mail: [email protected] Manufacturer: Golden Wealth Industrial Ltd Manufacturer Address: Unit G, 9/F, Valiant Industrial Center, 2-12 Au Pui Wan Street, Fotan, N.T., Hong Kong. Brand Name: HeathCo LLC Model: WLTX-205 Type of EUT: Transmitter Description of EUT: Wireless Door Chime Transmitter Serial Number: N/A FCC ID / IC: BJ4-WLTX205 / 3984A-WLTX205 Date of Sample Submitted: May 12, 2015 Date of Test: May 12, 2015 to June 19, 2015 Report No.: 15050668HKG-002 Report Date: June 22, 2015 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: 15050668HKG-002 ii FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 SUMMARY OF TEST RESULT TEST SPECIFICATION REFERENCE RESULTS Transmitter Field Strength, Bandwidth and Timing Requirement 15.231(a) / RSS-210 A1.1.1 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2013 Edition RSS-210 Issue 8, December 2010 RSS-Gen Issue 4, December 2014 Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. INTERTEK TESTING SERVICES Report No.: 15050668HKG-002 iii FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Table of Contents 1.0 General Description.........................................................................................1 1.1 Product Description ........................................................................................1 1.2 Related Submittal(s) Grants............................................................................1 1.3 Test Methodology ...........................................................................................1 1.4 Test Facility ....................................................................................................1 2.0 System Test Configuration ..............................................................................2 2.1 Justification.....................................................................................................2 2.2 EUT Exercising Software................................................................................2 2.3 Special Accessories .......................................................................................2 2.4 Measurement Uncertainty...............................................................................2 2.5 Support Equipment List and Description.........................................................2 3.0 Emission Results .............................................................................................3 3.1 Field Strength Calculation...............................................................................3 3.2 Radiated Emission Configuration Photograph ................................................4 3.3 Radiated Emission Data .................................................................................4 4.0 Equipment Photographs ..................................................................................7 5.0 Product Labelling .............................................................................................7 6.0 Technical Specifications .................................................................................7 7.0 Instruction Manual ...........................................................................................7 8.0 Miscellaneous Information ..............................................................................8 8.1 Measured Bandwidth.........................................................................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Configuration Photographs Worst-Case Radiated Emissions (Front View) Model : WLTX-205 INTERTEK TESTING SERVICE Report No: 15050668HKG-002 FCC ID: BJ4-WLTX205 IC: 3984A-WLTX205 Configuration Photographs Worst-Case Radiated Emissions (Back View) Model : WLTX-205