BJM-TTABB12DTablet PC With 802.11b WLAN

ACCESSORY CHECKLIST Standard Accessories (depends on model and configuration) USB Keyboard USB Mouse Power Cord AC Adapter Cleaning Cloth Stylus (includes an eraser function) Stylus Tether Slipcover Recovery CD Microsoft Windows XP Tablet PC Edition Introductory Guide Optional Accessories Keyboard Stand SAFETY GUIDELINES Safety Information Please pay attention to the following two symbols that appear in the User Manual. Each symbol is followed by important, useful information that will help you use your Tablet PC. Warning! This symbol warns of incorrect usage of equipment and/or a violation of the instructions for usage that will damage the Tablet PC or impair its performance. Attention! This symbol marks advice that will help you get better results when using your Tablet PC. Safety and Regulatory Information z When moving the Tablet PC, be careful not to drop it. z Do not dismantle the outer casing, especially during system start-up. Any type of dismantling will damage the system, and the manufacturer will not be held responsible. z Using an incorrect memory module may damage the system. z Do not install any expansion card that draws large amounts of electric current and will overload the system. z If the battery is replaced incorrectly, there is the risk of an explosion. When replacing the battery, the user should use the same kind as the original. Dispose of the used battery according to the manufacturer’s instructions. In order to get optimal results from your Tablet PC, please follow the recommendations below. The user should remember: z When viewing the computer screen, please maintain a distance of 38cm–45cm for the best results. z Avoid exposing the computer screen to direct sunlight, which can cause viewing discomfort and/or reduce the screen brightness. Power Cord and Power Supply Safety Guidelines z Use together with the designated AC adapter. z Keep away from cold. z Keep away from high temperatures or fire hazards. z Do not short-circuit the power-out. z Do not set in water. z Do not use in humid areas. z Do not pull on the power cord. z Use together with the designated power cord. z Operate at a room temperature of 5 o C–40 o C (41 o F–104 o F), relative humidity 10%–95% z High voltage inside; do not open. z Do not try to alter or repair. z Do exert pressure on or drop. z Store at a room temperature of -20 o C–85 o C (-4 o F–185 o F), relative humidity 5%–95%. z Do not damage the cord insulation. z Set the computer up near an AC outlet. The AC power cord is the main AC power breaker for the Tablet PC, and you must be able to access it easily. For safety reasons, the power cord supplied with the system has a grounded plug. You also need to plug the power cord into a grounded wall outlet to avoid the danger of electric shock. z This system can handle a power system of 100–240V. It is suitable for use in the place or country of purchase. z In order to reduce the possibility of electric shock from the telephone network, plug the computer power cord into the AC outlet before connecting the computer with the telephone line. Also, you should disconnect the telephone line first when unplugging the computer power cord from the AC power outlet. z Do not repair the power supply yourself. To avoid damage to the power supply, contact a professional to have it repaired or replaced. z All performance procedures, adjustments, controls, etc. aside from those that are listed in the User Manual (as computer upgrading and maintenance) can cause serious radiation damage. In order to avoid laser exposure, please do not open the LCD cover. Battery Safety Guidelines z The battery is restricted to usage with this computer. z Do not dismantle the battery. z Do not expose the battery to fire or water. z Avoid fire, heat and any sort of damage to the battery. Do not touch either end of the battery with anything metallic. z Be extremely careful when using a damaged or leaking battery. z If the surrounding temperature exceeds 45 o C (113 o F), do not charge the battery. z If electrolytes come into contact with the battery, use soap and water to clean the affected area. z If electrolytes come into contact with your eyes, wash your eyes with water for 15 minutes, and then go to a physician immediately. z To buy a battery, contact a local distributor. z Do not store the battery in a warehouse under high temperatures (over 60 o C, 140 o F). z When you want to dispose of the battery, consult your local Waste Treatment Center regarding disposal and recycling restrictions. Mercury Battery Warning z This computer contains a mercury battery that is used to power the clock and the calendar loop. z If the battery is improperly replaced, there is the risk of an explosion. Please only use an identical or equivalent battery supplied by the manufacturer when replacing the battery. Please dispose of the used battery in accordance with the manufacturer’s instructions and local laws. Operating Specifications Electrical Rating: DC 12V, 3.5A Operating Temperature: 25 o C (77 o F) Storage Temperature: -20 o C–70 o C (-4 o F–158 o F) Operating Humidity: under 26 o C (78.8 o F), 15%–80% humidity Storage Humidity: under 65 o C (149 o F), 90% humidity (no condensation) Storage Altitude: 0m–4572m TABLET PC INTRODUCTION Properties z The Tablet PC’s size is designed with the user in mind: while writing, you can conveniently rest your hand on top of the screen. z The Tablet PC’s advanced speech recognition system also allows it to be used as a dictation machine. (See Note 1.) z The wireless network function lets you conduct business no matter where you are, increasing your efficiency. z Inputting information into the computer is no longer any trouble! Using the stylus, you can write directly on the screen and handwritten documents can even be converted to typed text. (See Note 2.) Components z Processor: Intel Pentium M Processor z Memory: 256MB (Upgradeable to 1GB) z Hard Drive: 30G z Display: 12.1” TFT technology, 1024x768 resolu…

Text truncated - open the document above for the full version.

RE FW TATUNG CO. FCC IDBJM-TTABB12D AN03T3212.txt To: [email protected]; Mike Kuo Cc: Eric (E-mail); John Lee (E-mail); Lucy (E-mail); Ting (E-mail) Subject: RE: FW: TATUNG CO., FCC ID:BJM-TTABB12D, AN03T3212 Hi Lucy : Received additional SAR evaluation report, the following statement is for your information only. do not reply: SAR test configruation: Test configruation #1: for most of tablet PC ( or so called panel PC ), the end user can change the screent orientation 0, 90, 180 and 360 degree based upon the usage. When you test such product, you have to consider the normal operating condition. In the RF exposure complaince evaluation, to test the worst case is not the intend. RF exposure complaince shall be evaluated as normal operating conditons. As illustrated in configuration #1 setup photo, configuration #1 is tested to simulate arm-held operation. It is true that the end user may place this tablet PC on the desktop table to transmit a large file and before the transmission is ended, carry this tablet PC underneth the arm and relocate his/her position from one place to the other. At this configruation, you need to consider the transmission duration time. By the time the end user pick up the tablet PC , the transmission may be ended. TCB has discussed this type of device configuration with FCC. Based upon the duty cycle , tranmission duration time and the inforamtion contains in the user manual, FCC does not consider arm-held is the normal operating condition. To perform SAR evaluation during configruaiton #1 usage, the test lab may be over-tested. Test configuration #2: I believe this test configuraiton is to simulate the near-by person configuraiton. If you compare configraution #2 and configuration #1, you may notice the same conditions were tesed but with different separation distance. Test configuraiton #2 is considered as normal operating condition and SAR evaluation shall be performed and test report did contain such information. Test configuration #3: I believe this tes configuration is to simulate lap-held opeating condition, such configuation is considered as normal operating condition. Additional SAR evalution is provided to address this configuraiton. Best Regards Mike Kuo -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Thursday, August 28, 2003 4:05 AM To: Mike Kuo Cc: Eric (E-mail); John Lee (E-mail); Lucy (E-mail); Ting (E-mail) Subject: FW: TATUNG CO., FCC ID:BJM-TTABB12D, AN03T3212 Hi Mike, Regard Q1, the IDs of USB keyboard and mouse are BSMI but not FCC ID. We have corrected it as the attached revised test report. Best Regards, Lucy Mike Kuo <[email protected]> Page 1 RE FW TATUNG CO. FCC IDBJM-TTABB12D AN03T3212.txt 2003/08/28 01:18 AM "Eric (E-mail)" <[email protected]>, "Lucy (E-mail)" <[email protected]>, "Ting (E-mail)" <[email protected]> "John Lee (E-mail)" <[email protected]> FW: TATUNG CO., FCC ID:BJM-TTABB12D, AN03T3212 -----Original Message----- From: CERTADM Sent: Wednesday, August 27, 2003 9:16 AM To: '[email protected]' Subject: TATUNG CO., FCC ID:BJM-TTABB12D, AN03T3212 Notice_content ------------- 15.247 portion of review: Question #1: Page 10 of test report indicate the FCC ID number of USB keyboard and USB mouse. These FCC ID numbers can not be verified. Please explain. SAR Portion of review: Question #2: Due to the output power and separation distance between the transmitting antenna to the body of user, this device requires to be evaluated for SAR compliance to qualify TCB review. There is no SAR test report and associated attachments provided. Please provide SAR evaluation report to address RF exposure compliance. Due to lack of SAR test report, RF exposure compliance portion has not yet been reviewed. Best Regards Mike Kuo The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Page 2

Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 1 APPENDIX 2 EXTERNAL PHOTOGRPHS OF EUT Front view of EUT Back view of EUT Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 2 Left view of EUT Right view of EUT Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 3 View of EUT Digital Pen Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 4 Front view of Adapter Back view of Adapter

Scale: 2:1 35.5mm 99.5mm R1X4 Tatung Tablet PC Assembled by TATUNG CO. 400,Chenteh.Rd.,7th Sec.,Peitou.Taipei Taiwan,122,R.O.C. Operate this device only with AC adapter provided with this product Made in Taiwan Model No.: TTAB-B12D Input: 12V 2.5A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Canada RSS-210. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Canada ICES-003 CLASS B/NMB-003 CLASS B. IC:XXXXXXXXX FCC ID: BJM-TTABB12D TTAB-B12D

LABEL AREA

Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 1 APPENDIX 3 INTERNAL PHOTOGRPHS OF EUT Internal of EUT --- 1 Internal of EUT --- 2 Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 2 Internal of EUT --- 3 Internal of EUT --- 4 Antenna Position Antenna Position Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 3 Internal of EUT --- 5 Internal of EUT --- 6 Antenna Position Antenna Position Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 4 Internal of EUT --- 7 Internal of EUT --- 8 Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 5 Module --- 1 Module --- 2 Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page 6 Module --- 3 Module --- 4 Compliance Certification Services Inc. Report No: B30805205-RP FCC ID: BJM-TTABB12D Date of Issue: August 20, 2003 Page7 Module --- 5

APPROVAL SHEET CUSTOMER TATUNG CORP LTD; FILE NO . : ESCRIPTION : ANTENNIQUES P/N :FI-001-249-01 CUSTOMER P/N : DATE : 92 07 28 Customer Approval Antenniques Co.,Ltd 12265 TEL02-2668-5793 FAX02-2668-5795 5F,No.6,Laine 122, Sec 2,Ganyun St, Shulin Chulin City, Taipei Hsien,238 Taiwan R.O.C. [email protected] www.antenniques.com.tw MAIN ANTENNA RETURN LOSS V. S . W. R SMITH CHART Antenniques Co., Ltd. 2002/7/25 1 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 PIFA Antenna Test Report Antenniques Co., Ltd. 2002/7/25 2 2 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 I. 802.11 and BLUETOOTH Antenna Testing Conditions: 1. Testing set up: LCD OPEN LCD CLOSE 750 cm HORN Standard Antenna 8753ES Network Analyzer Rotator Controller Radiation Pattern Testing - Anechoic Chamber DUT Antenna X Y Antenniques Co., Ltd. 2002/7/25 3 3 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 2. Testing procedure description: (1). Testing environment ： (a) Anechoic chamber: The simulated far field antenna gain measurement field. (b) Standard Horn antenna: Using two st andard horn antennas to do the standard calibration tool for the anechonic chamber space absorption. (2). Testing concept: (a) The antenna gain pattern is the 3D map. In general, using the two dimensions orthogonal plane measurement to approach the 3D gain pattern. The H-horizontal plane and V-vertical plane measured data are the two dimension orthogonal plane data to approach the 3D pattern. (b) For notebook using method, the LCD panel is always opened or closed. So, the NB antenna gain testing is under the LCD panel closed and opened conditions. (3). Antenna performance verification: Accord ing the IEEE 802.11b standard, the necessary communication distance is larger than 100m. The required antenna gain must be greater than –3.5dBi (H+V). For the bluetooth case, the required gain must be greater than –5dBi(H+V) Antenniques Co., Ltd. 2002/7/25 4 4 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 3. Mechanical dimensions 4. Judge Conditions: 802.11 ： Peak Gain ≤ 3dBi ， Average Gain more larger is better 。 BLUETOOTH ： Average Gain ≥ -5dBi PIFA Antenna 2 PIFA Antenna 1 Antenniques Co., Ltd. 2002/7/25 5 5 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 II. Gain Pattern of Left Antenna ： Test results 1 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-open Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Wireless LAN LEFT 1.13 700 Off Gain of XY Plane(Azimuth)-open Antenna Frequency 2.45 Peak 1.12389 1 H Average -4..5998 Peak -2.5433 1 V Average -8.657 Peak 1.12389 1 V+H Average -2.9788 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 6 6 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 Test results 2 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-close-face up Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Wireless LAN LEFT 1.13 700 Off Gain of XY Plane(Azimuth)-close-face up Antenna Frequency 2.45 Peak -3.959 1 H Average -5.6045 Peak -0.832 1 V Average -7.354 Peak -0.832 1 V+H Average -3.456 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 7 7 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 Test results 3 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-close-face down Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Wireless LAN LEFT 1.13 700 Off Gain of XY Plane(Azimuth)-close-dowm Antenna Frequency 2.45 Peak -0.318 1 H Average -6.0294 Peak -5.059 1 V Average -7.165 Peak -0.318 1 V+H Average -3.358 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 8 8 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 III. Gain Pattern of Right Antenna ： Test results 4 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-open Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Bluetooth RIGHT 1.13 700 Off Gain of XY Plane(Azimuth)-open Antenna Frequency 2.45 Peak 1.0045 2 H Average -3..5998 Peak -2.736 2 V Average -6.4338 Peak 1.0045 2 V+H Average -0.564 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 9 9 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 Test results 5 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-close-face up Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Bluetooth RIGHT 1.13 700 Off Gain of XY Plane(Azimuth)-close-face up ntenna Frequency 2.45 Peak -1.318 2 H Average -5.7490 Peak -1.832 2 V Average -7.847 Peak -1.318 2 V+H Average -3.821 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 10 10 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 Test results 6 1. Peak Gain and Average Gain 2. Radiation Pattern of XY Plane(Azimuth)-close-face down Antenna Application Placement Cable dia. Φ mm Cable length mm NB Power PIFA Bluetooth RIGHT 1.13 700 Off Gain of XY Plane(Azimuth)-close-face down ntenna Frequency 2.45 Peak -1.218 2 H Average -5.8390 Peak -6.432 2 V Average -8.683 Peak -1.218 2 V+H Average -4.117 H-polarized V- polarized Antenniques Co., Ltd. 2002/7/25 11 11 5f,No.6, Lane 122, Sec 2, Ganyuan St., Shulin City,Taipei,238 Taiwan, R.O.C. Tel: 886-2-26685793 Fax: 886-2-26685795 IV. Electronic Characteristic of Left Antenna ： Test results7 1.V.S.W.R 2.RETURN LOSS Antenna Applicati…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No: -SAR-FCC Date of Issue: September 06, 2003 Page 1 of 25 in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C For Tatung Company TABLET PC Model: TTAB-B12D FCC ID: BJM-TTABB12D Tr a d e Na me : TATUNG Prepared for TATUNG CO. 22 Chungshan N. Rd.,3 Sec. Taipei Taiwan ,104, R.O.C. Prepared by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Note: This report shall not be reproduced except in full, without the written approval of C&C Laboratory Co., Ltd. This document may be altered or revised by C&C Laboratory Co., Ltd. personnel only, and shall be noted in the revision section of the document. Compliance Certification Services Inc. Report No: -SAR-FCC Date of Issue: September 06, 2003 Page 2 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION................................................................................ 3 2. EUT DESCRIPTION........................................................................................................ 3 3. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC....... 5 4. DOSIMETRIC ASSESSMENT SYSTEM ..................................................................... 6 4.1 MEASUREMENT SYSTEM DIAGRAM ............................................................................. 7 4.2 SYSTEM COMPONENTS .................................................................................................... 8 5. EVALUATION PROCEDURE ..................................................................................... 10 5.1 DATA EVALUATION ........................................................................................................ 10 5.2 SAR EVALUATION PROCEDURE................................................................................... 12 6. MEASUREMENT UNCERTAINTY ............................................................................ 13 7. EXPOSURE LIMIT........................................................................................................ 14 8. MEASUREMENT RESULTS ....................................................................................... 15 8.1 SYSTEM VALIDATION..................................................................................................... 15 8.2 TEST LIQUID CONFIRMATION ...................................................................................... 15 8.3 EUT TUNE-UP PROCEDURE............................................................................................ 17 8.4 EUT SETUP PHOTOS......................................................................................................... 19 8.5 SAR MEASUREMENT RESULT ....................................................................................... 21 9. EUT PHOTOS................................................................................................................. 22 10. EQUIPMENT LIST & CALIBRATION ...................................................................... 23 11. REFERENCES................................................................................................................ 24 12. ATTACHMENT.............................................................................................................. 25 Compliance Certification Services Inc. Report No: -SAR-FCC Date of Issue: September 06, 2003 Page 3 1. TEST RESULT CERTIFICATION Applicant: TATUNG COMPANY 22 Chungshan N. Rd.,3 Sec. Taipei Taiwan ,104, R.O.C. Equipment Under Test: TABLET PC Trade Name: TATUNG Model: FCC ID BJM-TTABB12D Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Report Number: B30805205-SAR-FCC Date of Test: Aug 15, Sep 06, 2003 Test Sample is a: TABLET PC Modulation Type: Direct Sequence Spread Spectrum Operating Mode: Maximum continuous output Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: 15.32dBm (2412 MHz) (Conducted) Max. SAR (1g): 1.36mW/g (2462MHz) Application Type: Certification FCC Rule part(s): § 15.247 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1999 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 - see Test Report). I attest to accuracy of the data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for completeness of these measurements and vouch for the qualifications of all persons taking them. Approved by: Reviewed by: Jonson Lee / Director Miro Chueh / Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Compliance Certification Services Inc. Report No: B30725003-SAR-FCC Date of Issue: September 06, 2003 Page 4 2. EUT DESCRIPTION Applicant: TATUNG COMPANY 22 Chungshan N. Rd.,3 Sec. Taipei Taiwan ,104, R.O.C. Equipment Under Test: TABLET PC Trade Name: TATUNG Model: FCC ID BJM-TTABB12D Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Report Number: B30805205-SAR-FCC Date of Test: Aug 15, Sep 06, 2003 Test Sample is a: TABLET PC Modulation Type: Direct Sequence Spread Spectrum Operating Mode: Maximum continuous output Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: 15.32dBm (2412MHz) (Conducted) Max. SAR (1g): 1.36mW/g (2462MHz) Application Type: Certification FCC Rule part(s): § 15.247 Notes: 1. Specific Absorption Rate (SAR) is a measure of the rate of energy absorption due to exposure to an RF transmitting source (wireless portable device). 2. EEE/ANSI Std. C95.1-1999 limits are used to determine compliance with FCC ET Docket 93-62 Compliance Certification Services Inc. Report No: -SA…

Text truncated - open the document above for the full version.

Date/Time: 08/15/03 16:07:24 Test Laboratory: C&C Labratory CO., Ltd File Name: 2450-Dipole-1.da4 2450-Dipole-1 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Program: System Performance Check at 2450MHz Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL2450 (σ = 1.8186 mho/m, ε r = 39.23, ρ = 1000 kg/m 3 ) Air Temperature 25.7 deg C ; Liquid Temperature 25.2 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(5.1, 5.1, 5.1); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 Pin=250mW,d=10mm/Area Scan (5x5x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 92.8 V/m Power Drift = 0.06 dB Maximum value of SAR = 14.2 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 92.8 V/m Power Drift = 0.03 dB Maximum value of SAR = 13.9 mW/g Pin=250mW,d=10mm/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 27.7 W/kg SAR(1 g) = 13.5 mW/g; SAR(10 g) = 6.27 mW/g Reference Value = 92.8 V/m Power Drift = 0.06 dB Maximum value of SAR = 15 mW/g Page1 Page2 Date/Time: 09/06/03 09:53:56 Test Laboratory: Compliance Certification Services Inc. File Name: 2450-Dipole-1.da4 2450-Dipole-1 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Program: System Performance Check at 2450MHz Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL2450 (σ = 1.8212 mho/m, ε r = 39.18, ρ = 1000 kg/m 3 ) Air Temperature 25.7 deg C ; Liquid Temperature 25.3 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(5.1, 5.1, 5.1); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 Pin=250mW,d=10mm/Area Scan (5x5x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 92.8 V/m Power Drift = 0.06 dB Maximum value of SAR = 14.2 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 92.8 V/m Power Drift = 0.03 dB Maximum value of SAR = 13.9 mW/g Pin=250mW,d=10mm/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 27.7 W/kg SAR(1 g) = 13.6 mW/g; SAR(10 g) = 6.28 mW/g Reference Value = 92.8 V/m Power Drift = 0.06 dB Maximum value of SAR = 15.1 mW/g Page1 Page2 Date/Time: 08/15/03 17:00:39 Test Laboratory: C&C Labratory CO., Ltd File Name: 0mm.da4 EUT Configuration 1 Page1 Date/Time: 08/15/03 16:31:09 Test Laboratory: C&C Labratory CO., Ltd File Name: 0mm.da4 0mm DUT: TABLET pc; Type: TABLET pc; Serial: n/a Program: 0mm Communication System: DSSS; Frequency: 2412 MHz;Duty Cycle: 1:1 Medium: HSL2450 (σ = 1.98 mho/m, ε r = 51.7, ρ = 1000 kg/m 3 ) Air Temperature 25.7 deg C ; Liquid Temperature 25.2 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 12; Type: SAM V4.0; Serial: TP-1271 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 CH 1/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 7.93 V/m Power Drift = 0.09 dB Maximum value of SAR = 0.778 mW/g CH 1/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 7.93 V/m Power Drift = 0.1 dB Maximum value of SAR = 0.874 mW/g CH 1/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 2.3 W/kg SAR(1 g) = 0.949 mW/g; SAR(10 g) = 0.356 mW/g Reference Value = 7.93 V/m Power Drift = 0.09 dB Maximum value of SAR = 1.16 mW/g Page1 Page2 Date/Time: 08/15/03 16:46:42 Test Laboratory: C&C Labratory CO., Ltd File Name: 0mm.da4 0mm DUT: TABLET pc; Type: TABLET pc; Serial: n/a Program: 0mm Communication System: DSSS; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium: HSL2450 (σ = 1.98 mho/m, ε r = 51.7, ρ = 1000 kg/m 3 ) Air Temperature 25.7 deg C ; Liquid Temperature 25.2 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 0mm (Fix Surface) Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 12; Type: SAM V4.0; Serial: TP-1271 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.6 Build 115 CH 6/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 8.25 V/m Power Drift = 0.04 dB Maximum value of SAR = 0.919 mW/g CH 6/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR …

Text truncated - open the document above for the full version.