BJM-TWN5213BZNWeb PAD with 11b WLAN

2005/6/27 page1 TATUNG Wireless Thin Client TWN-5213 CU TATUNG Wireless Thin Client (TX-2000) User Guide Copyright In the interest of continuing product improvement, TATUNG Co. reserves the right to change product specifications and information in this document without notice. TATUNG Co. makes no warranty of any kind with regard to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. TATUNG Co. shall not be liable for any errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this document or the examples herein. © TATUNG Co. All rights reserved. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, adapted, or translated to another language without the prior written consent of TATUNG Co., except as allowed under the copyright laws. The programs that control this product are copyrighted and all rights are reserved. Reproduction, adaptation, or translation of those programs without prior written permission of TATUNG Co. is also prohibited. Tatung is the registered trademark of TATUNG Co. Microsoft, Windows XP embedded, and the Windows logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by Microsoft Licensing, Inc., a wholly owned subsidiary of Microsoft Corporation. All other brand names and products names used in this document are trade names, service marks, trademarks, or registered trademarks of their respective owners. TATUNG Co. 22 Chungshan North Road, Section 3 Taipei, Taiwan 104 R.O.C. http://www.tatung.com TATUNG Wireless Thin Client (TX-2000) User Guide Messages Messages are used in this document to bring important information to your attention. Different types of messages are defined as follows: CAUTION!: A Caution alert informs you that improper use of equipment or failure to follow safety instructions may cause data loss or equipment damage. WARNING!: A Warning alert informs you that improper use of equipment or failure to follow safety instructions may cause bodily injury. NOTE!: A Note is an advice that helps you make the best use of TWN-5213 CU. Safety Instructions You must read through all safety instructions before using TWN-5213 CU. The following information contains concepts that you must fully understand in order to avoid property damage or body injury. CAUTION! • Always use standard battery packs supplied with the TWN-5213 CU. Other battery packs may have different specifications and cause damages to TWN-5213 CU. • Do not expose the battery pack to other metal objects. • Do not use or place TWN-5213 CU near sources of heat or expose it to direct sunlight for an extended period of time. Store it in a cool and dry place. • Do not push or apply force to the TFT screen. • Do not use pens or sharp objects to write on the screen. Always use the stylus to tap or draw on the TFT screen. WARNING! • Using worn-out or damaged power cords may result in electric shock or fire. • Avoid keeping a steady position when using TWN-5213 CU for prolonged period of time. Periodic exercises and breaks are recommended to prevent any physical discomfort. • Always contact an authorized TATUNG service provider for assistance if any repair or adjustment is required. TATUNG Wireless Thin Client (TX-2000) User Guide Table of Contents 1. Overview............................................................................................................................................................ 5 2. Equipment Checklist ........................................................................................................................................ 6 3. TWN-5213 CU Specification............................................................................................................................. 7 4. TWN-5213 CU Features .................................................................................................................................... 8 4.1 Front View of TWN-5213 CU........................................................................................................................................ 8 4.2 Top View of TWN-5213 CU ........................................................................................................................................ 11 4.3 Left View of TWN-5213 CU ........................................................................................................................................ 11 4.4 Right View of TWN-5213 CU...................................................................................................................................... 12 4.5 Back View of TWN-5213 CU ...................................................................................................................................... 13 5. Quick-Start Procedure ................................................................................................................................... 15 5.1 Starting TATUNG TWN-5213 CU............................................................................................................................... 15 5.2 Booting Logo .............................................................................................................................................................. 18 5.3 Device Settings .......................................................................................................................................................... 20 5.4 LCD Panel Setting...................................................................................................................................................... 21 5.7 Recalibrating the Touch-Screen ..................................................................................…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

FCC ID Label Location (FCC ID: BJM-TWN5213BZN)

V210_Taiwan System Label V210_Taiwan System Label 0391I-A4-930065 5837101370 system label assembly Input: DC16V 2.5A Note: 1.材質 Surface: Matte Polyester (clear) Second layer: Polyester t =0.075 mm Third layer: Adhesive 3M468 or UL standard Fourth layer: Easy removable paper. 符合UL/CSA規定 2.顏色 Print Ground color: Matching color with the rear cabinet(Black) Font color: Silver 3.標籤背膠與印刷需通過IMN-21-87-0017標籤測試規範 4. 廠商交貨前,必需完成樣品承認. � Size 77 x 28 mm R1 x4Taiwan production FCC ID:BJM-TWN5213BZN Model: TWN-5213 CU Wireless Thin Client Caution : This device complies with part15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 0560 MADE IN TAIWAN E132236

Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19

FCC ID: BJM-TWN5213BZN Report No.RF940517L03 Technical Description The transmitter of the EUT (Web PAD) is powered by AC adapter. The antenna used in this product is printed monopole antenna without any antenna connector. The other instruction, please have a look at the users manual. DSSS Information This device is Direct Sequence Spread Spectrum, the data is mixed by pseudorandom code which is an orthogonal code. The mixed data is digital modulated by BPSK and QPSK technique depends on the data rates. The CCK coding is applied for increasing the data rate, and also the processing gain will be increased. The bit rates are 1,2,5.5,11Mbps, the symbol rates are 1,1,1.375,1.375Mbps, the chip rates are always 11Mbps. So, the Chip/symbol is 11,11,8 and 8 respectively. Although is higher bit rate, the processing gain is lower than 10, but the CCK coding used in higher bit rate will provide 2.2dB coding gain.

D3: DAE SN: 579

APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION D1: SAM PHANTOM

A - 1 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA A1: TEST CONFIGURATION The lateral of the EUT to the flat phantom distance 0 mm A - 2 The tip of the EUT to the flat phantom distance 0 mm A - 3 The bottom of the EUT to the flat phantom distance 0 mm EUT Photo A - 4 A - 5 Liquid Level Photo MSL 2450MHz D=152mm A - 6 Date/Time: 2005/6/14 11:02:09 Test Laboratory: Advance Data Technology Web PAD-Lateral Right Antenna 11b Mode 1 DUT: Web PAD ; Type: TWN-5213 ; Test Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.98 mho/m; ε r = 53.5; ρ = 1000 kg/m 3 ; Liquid level : 152 mm Phantom section: Flat Section ; Separation distance : 0 mm (The lateral side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 23.0 degrees ; Liquid temp. : 22.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (6x8x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.479 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 4.51 V/m Peak SAR (extrapolated) = 3.19 W/kg SAR(1 g) = 1.04 mW/g; SAR(10 g) = 0.349 mW/g Maximum value of SAR (measured) = 1.19 mW/g A - 7 A - 8 Date/Time: 2005/6/14 11:34:10 Test Laboratory: Advance Data Technology 1.1.1Web PAD-Lateral Right Antenna 11b Mode 1 DUT: Web PAD ; Type: TWN-5213 ; Test Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2437 MHz; σ = 2.02 mho/m; ε r = 53.4; ρ = 1000 kg/m 3 ; Liquid level : 152 mm Phantom section: Flat Section ; Separation distance : 0 mm (The lateral side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 23.0 degrees ; Liquid temp. : 22.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Middle Channel 6/Area Scan (6x8x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.413 mW/g Middle Channel 6/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.95 V/m Peak SAR (extrapolated) = 2.72 W/kg SAR(1 g) = 0.880 mW/g; SAR(10 g) = 0.293 mW/g Maximum value of SAR (measured) = 1.000 mW/g A - 9 Date/Time: 2005/6/14 12:05:26 Test Laboratory: Advance Data Technology 1.1.2Web PAD-Lateral Right Antenna 11b Mode 1 DUT: Web PAD ; Type: TWN-5213 ; Test Frequency: 2462 MHz Communication System: 802.11b ; Frequency: 2462 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2462 MHz; σ = 2.05 mho/m; ε r = 53.4; ρ = 1000 kg/m 3 ; Liquid level : 152 mm Phantom section: Flat Section ; Separation distance : 0 mm (The lateral side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 23.0 degrees ; Liquid temp. : 22.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 High Channel 11/Area Scan (6x8x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.392 mW/g High Channel 11/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.63 V/m Peak SAR (extrapolated) = 2.48 W/kg SAR(1 g) = 0.789 mW/g; SAR(10 g) = 0.262 mW/g Maximum value of SAR (measured) = 0.883 mW/g A - 10 Date/Time: 2005/6/14 13:47:00 Test Laboratory: Advance Data Technology Web PAD-Tip Right Antenna 11b Mode 2 DUT: Web PAD ; Type: TWN-5213 ; Test Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.98 mho/m; ε r = 53.5; ρ = 1000 kg/m 3 ; Liquid level : 152 mm Phantom section: Flat Section ; Separation distance : 0 mm (The tip of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 23.0 degrees ; Liquid temp. : 22.0 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579; Calibrated: 2005/3/23 - Phantom: SAM 12; Type: SAM V4.0; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (8x10x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.064 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.71 V/m Peak SAR (extrapolated) = 0.139 W/kg SAR(1 g) = 0.067 mW/g; SAR(10 g) = 0.034 mW/g Maximum value of SAR (measured) = 0.075 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 1: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.71 V/m Peak SAR (extrapolated) = 0.187 W/kg SAR(1 g) = 0.082 mW/g; SAR(10 g) = 0.039 mW/g Maximum value of SAR (measured) = 0.095 mW/g A - 11 A - 12 Date/Time: 2005/6/14 14:28:36 Test Laboratory: Advance Data Technology Web PAD-Tip Right Antenna 11b Mode 2 DUT: Web PAD ; Type: TWN-5213 ; Test Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz; Duty Cycle: 1:1; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2437 MHz; σ = 2.02 mho/m; ε r = 53.4; ρ = 1000 kg/m 3 ; Liqu…

Text truncated - open the document above for the full version.

B - 1 APPENDIX B: ADT SAR MEASUREMENT SYSTEM C - 1 APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION

FCC ID: BJM-TWN5213BZN Report no.: SA940517L031Report Format Version 2.0.1 SAR TEST REPORT REPORT NO.: SA940517L03 MODEL NO.: TWN-5213 RECEIVED: May 17, 2005 TESTED: Jun. 14, 2005 ISSUED: Jun. 23, 2005 APPLICANT: TATUNG CO. ADDRESS: 22, Chungshan N. Rd., 3rd Sec., Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 36 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: BJM-TWN5213BZN Report no.: SA940517L032Report Format Version 2.0.1 TABLE OF CONTENTS 1.CERTIFICATION........................................................................................................................ 3 2.GENERAL INFORMATION........................................................................................................ 4 2.1GENERAL DESCRIPTION OF EUT.......................................................................................... 4 2.2GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................... 5 2.3GENERAL INOFRMATION OF THE SAR SYSTEM ................................................................. 5 2.4GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION ................................ 8 3.DESCRIPTION OF SUPPORT UNITS .................................................................................... 12 4.DESCRIPTION OF TEST MODES AND CONFIGURATIONS................................................ 13 4.1. DESCRIPTION OF ANTENNA LOCATION............................................................................. 13 4.2. DESCRIPTION OF ASSESSMENT POSITION ...................................................................... 14 4.3. DESCRIPTION OF TEST MODE ............................................................................................ 15 4.4. SUMMARY OF TEST RESULT ............................................................................................... 15 5.TEST RESULTS ...................................................................................................................... 16 5.1TEST PROCEDURES .............................................................................................................16 5.2MEASURED SAR RESULT ..................................................................................................... 18 5.3SAR LIMITS ............................................................................................................................. 20 5.4RECIPES FOR TISSUE SIMULATING LIQUIDS .................................................................... 21 5.5TEST EQUIPMENT FOR TISSUE PROPERTY...................................................................... 23 6.SYSTEM VALIDATION ............................................................................................................24 6.1TEST EQUIPMENT ................................................................................................................. 24 6.2TEST PROCEDURE................................................................................................................ 25 6.3VALIDATION RESULT............................................................................................................. 27 6.4SYSTEM VALIDATION UNCERTAINTIES .............................................................................. 28 7.MEASUREMENT SAR PROCEDURE UNCERTAINTIES ...................................................... 29 7.1. PROBE CALIBRATION UNCERTAINTY................................................................................. 29 7.2. ISOTROPY UNCERTAINTY.................................................................................................... 30 7.3. BOUNDARY EFFECT UNCERTAINTY................................................................................... 30 7.4. PROBE LINEARITY UNCERTAINTY ...................................................................................... 31 7.5. READOUT ELECTRONICS UNCERTAINTY.......................................................................... 31 7.6. RESPONSE TIME UNCERTAINTY ........................................................................................ 31 7.7. INTEGRATION TIME UNCERTAINTY .................................................................................... 32 7.8. PROBE POSITIONER MECHANICAL TOLERANCE ............................................................. 33 7.9. PROBE POSITIONING............................................................................................................ 33 7.10. PHANTOM UNCERTAINTY .................................................................................................... 34 7.11. DASY4 UNCERTAINTY BUDGET .......................................................................................... 35 8.INFORMATION ON THE TESTING LABORATORIES............................................................ 36 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: BJM-TWN5213BZN Report no.: SA940517L033Report Format Version 2.0.1 1. CERTIFICATION PRODUCT : Web PAD MODEL NO. : TWN-5213 BRAND NAME : Tatung, NEC, Control 4 APPLICANT : TATUNG CO. TESTED : Jun. 14, 2005 TEST SAMPLE : ENGINEERING SAMPLE STANDARDS : FCC Part 2 (Section 2.1093), FCC OET Bulletin 65, Supplement C (01-01), RSS-102 The above equipment has been tested by Advance Data Technology Corporation, and f…

Text truncated - open the document above for the full version.

FCC ID: BJM-TWN5213BZN Report No.: RF940517L031Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940517L03 MODEL NO.: TWN-5213 RECEIVED: May 17, 2005 TESTED: May 30 ~ Jun. 09, 2005 ISSUED: Jun. 13, 2005 APPLICANT: Tatung Company ADDRESS: 22, Chungshan N. RD., 3rd Sec., Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 49 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: BJM-TWN5213BZN Report No.: RF940517L032Report Format Version 2.0.2 TABLE OF CONTENTS 1. CERTIFICATION ............................................................................................ 4 2. SUMMARY OF TEST RESULTS.................................................................... 5 2.1 MEASUREMENT UNCERTAINTY.................................................................. 5 3. GENERAL INFORMATION ............................................................................. 6 3.1 GENERAL DESCRIPTION OF EUT ............................................................... 6 3.2 DESCRIPTION OF TEST MODES ................................................................. 7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: ................. 8 3.2.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................... 10 3.2.4 DESCRIPTION OF SUPPORT UNITS.......................................................... 10 4. TEST TYPES AND RESULTS .......................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT ................................................11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ..............................11 4.1.2 TEST INSTRUMENTS ...................................................................................11 4.1.3 TEST PROCEDURES................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ......................................................... 12 4.1.5 TEST SETUP ................................................................................................ 13 4.1.6 EUT OPERATING CONDITIONS.................................................................. 13 4.1.7 TEST RESULTS............................................................................................ 14 4.2 RADIATED EMISSION MEASUREMENT .................................................... 20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT .................................. 20 4.2.2 TEST INSTRUMENTS .................................................................................. 21 4.2.3 TEST PROCEDURES................................................................................... 22 4.2.4 DEVIATION FROM TEST STANDARD ......................................................... 23 4.2.5 TEST SETUP ................................................................................................ 23 4.2.6 EUT OPERATING CONDITIONS.................................................................. 23 4.2.7 TEST RESULTS............................................................................................ 24 4.3 6dB BANDWIDTH MEASUREMENT............................................................ 28 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT.......................................... 28 4.3.2 TEST INSTRUMENTS .................................................................................. 28 4.3.3 TEST PROCEDURE ..................................................................................... 29 4.3.4 DEVIATION FROM TEST STANDARD ......................................................... 29 4.3.5 TEST SETUP ................................................................................................ 29 4.3.6 EUT OPERATING CONDITIONS.................................................................. 29 FCC ID: BJM-TWN5213BZN Report No.: RF940517L033Report Format Version 2.0.2 4.3.7 TEST RESULTS............................................................................................ 30 4.4 MAXIMUM PEAK OUTPUT POWER ........................................................... 33 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ............. 33 4.4.2 INSTRUMENTS............................................................................................ 33 4.4.3 TEST PROCEDURES................................................................................... 34 4.4.4 DEVIATION FROM TEST STANDARD ......................................................... 34 4.4.5 TEST SETUP ................................................................................................ 34 4.4.6 EUT OPERATING CONDITIONS.................................................................. 34 4.4.7 TEST RESULTS............................................................................................ 35 4.5 POWER SPECTRAL DENSITY MEASUREMENT ....................................... 36 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ..................... 36 4.5.2 TEST INSTRUMENTS .................................................................................. 36 4.5.3 TEST PROCEDURE ..................................................................................... 37 4.5.4 DEVIATION FROM TEST STANDARD ......................................................... 37 4.5.5 TEST SETUP ............................................................................…

Text truncated - open the document above for the full version.

FCC ID: BJM-TWN5213BZN Report No.: RF940517L0347Report Format Version 2.0.2 5. PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: BJM-TWN5213BZN Report No.: RF940517L0348Report Format Version 2.0.2 RADIATED EMISSION TEST