BVCAMS1140ANTI-PILFERAGE DEVICE

Preliminary AMS-1140 DETECTORS 8200-2684-02, REV. 0 SETUP AND SERVICE GUIDE 1 of 15 AMS-1140 Detectors Setup and Service Guide ZA1140-D Contents About this Guide .................................................... 1 Detector Service Features ..................................... 1 Circuit Board Pinouts ............................................. 3 Service Procedures ............................................... 3 Field Replaceable Units .................................. 3 Replacing the Secondary Cap Board .............. 3 Replacing the Interconnect Cable ................... 4 Installing the Pedestal Installation Kit .............. 5 Replacing the Alarm Board and Lens ............. 6 Replacing the Fuse ......................................... 7 Inhibiting the Transmitter ................................. 7 Using the Software Configurator ..................... 7 Connecting to AC Power ................................. 8 Tuning the Pedestals ...................................... 9 Troubleshooting ................................................... 10 Checking Detector Operation ........................ 10 Dead system/Low sensitivity ......................... 10 False Alarms ................................................. 11 Understanding Error Codes .......................... 11 Interpreting LED Indicators ........................... 12 Specifications ....................................................... 15 Declarations ......................................................... 15 © 2010 Sensormatic Electronics LLC About this Guide This guide explains how to tune, service, and troubleshoot AMS-1140 detectors. Related documents are: • Installation Guide, AMS-1140 Detector, 8200- 2684-01 Detector Service Features AMS-1140 detectors have the following service- related features: • Power on self-test. Upon power up or hardware reset, detector software runs a self- test to ensure it functions. • Diagnostics. You use a laptop computer and configuration software to set up and configure the detector, and to determine its operational status. The detector also has an LED (DS5) inside the primary pedestal that flashes an error code if system software should fail. • Alarm indication. The top cap of the primary pedestal contains flashing LEDs; the base cover of the primary pedestal contains a piezo for an audio alarm. The volume of the audio alarm is controlled with a pot (RV3) on the main circuit board in the primary base cover. • Transmit inhibit. The base of the primary pedestal has a hole that provides access to a transmit-inhibit pushbutton. • Tags Too Close indication. If this feature is enabled by the configurator, the pedestal will flash a unique alarm pattern when a non- deactivated label or tag is left in the detection field of the detector for awhile. • Adjacent transmitter interference reduction. This feature allows service to adjust the Energy Trim Level to decrease the impact of electronic noise from nearby anti-theft systems. • Backfield reduction. If enabled by the configurator, the detector will reduce the size of the detection field behind the pedestals. • Simplified design. AMS-1140 detectors are a simplified design and do not support the following features or options: people-counting, relays, auto-phase, wired sync, jammer detect, auxiliary receivers, remote alarms and external alarm counters. AMS-1140 DETECTORS 8200-2684-02, REV. 0 SETUP AND SERVICE GUIDE 2 of 15 Figure 1. Primary pedestal main circuit board (0312-3072-01) pinouts J6 J4 J3 J2 J5 RV3 P6 Primary Tuning Jumpers Piezo Volume Pot Interconnect Connector RS-485 Network Port Service Port J1 Voltage Selection Jumper Pin Signal 1 RS-232 RX 2 RS-232 TX 3 GND 4 GND Pin Signal 1 RS-485 HI * 2 RS-485 LO * 3 SYNC HI 4 NOT USED 5 NOT USED 6 SYNC LO 7 GND 8 GND P5 P3 Tx Coil Connector Alarm Board Cable Connector Pin Signal Color 1 TX White 2 GND Shield 3 TX RETURN Black or Red DS4 DS5 DS3 DS1 DS2 DS7 DS6 F1 Fuse Line Input Pin Signal 1 NEUTRAL 2 GND 3 LINE P4 1 Pin Signal Color 1 TX White 2 GND Shield 3 TX RET Black 1 1 1 Pin Signal Color 1 GND Shield 2 ALARM Black 3 Unused 4 +12V Red Status Jumpers (See Figure 5 for close-up). AMS-1140 DETECTORS 8200-2684-02, REV. 0 SETUP AND SERVICE GUIDE 3 of 15 Circuit Board Pinouts The AMS-1140 pedestals each have a circuit board in their bases. Figure 1 and Figure 2 show the location of connectors, LEDS, jumpers, and fuses, as well as pinouts for the connectors. Figure 2. Secondary pedestal capacitor board (0312-3075-01) pinouts Service Procedures This section covers the setup and service of the AMS-1140 detector. Field Replaceable Units The AMS-1140 has the following Field Replaceable Units (FRU): Secondary capacitor board 0312-3075-01 Interconnect cable 0652-0506-01 Pedestal installation kit 0352-0444-01 Alarm lens installation kit 0352-0444-02 Replacing the Secondary Cap Board WARNING—RISK OF ELECTRIC SHOCK! Disconnect AC power when servicing. 1. Turn off power to the pedestal at the circuit breaker. 2. Remove the cover from the exit side of the secondary pedestal. To do this: loosen the four fasteners at the base of the cover, and then lift the bottom of the cover up and then off the base. 3. On the secondary board, disconnect the Tx Coil cable from connector P1 and the primary pedestal from connectors P2. Pull on the connectors, not the wires. 4. Loosen two fasteners securing the capacitor board and remove it from the base cover. Retain the insulator for the replacement board. 5. Use the two fasteners to secure the new capacitor board to the base cover. 6. Reconnect the two cables to the capacitor board. 7. Put the cover back on the base, ensuring that you do not pinch any cables. 8. Tighten the four screws holding the base cover. Tx Coil Connector Interconnect cable connector Secondary Tuning jumpers 1 P1 J2 P2 J1 1 Pin Signal Color 1 TX White 2 GND Shield 3 TX RETURN Black Pin Signal Color 1 TX White 2 GND Shield 3 TX RETURN Red or Black ULTRA•POST DETECTORS WITH SWITCHED MODE…

Text truncated - open the document above for the full version.

February 4, 2010 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA Re: Application for a Confidential Request for Anti-Pilferage Device, FCC ID: BVCAMS1140 Dear Sir or Madam: Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: AMS1140 Conf OpDes.pdf AMS1140 Conf SchemPri.pdf AMS1140 Conf SchemSec.pdf AMS1140 Conf BlkDia.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, William D. Owsley Principal EMC Engineer Compliance Engineering Tyco Retail Solutions Sensormatic Electronics, LLC. 6600 Congress Ave. Boca Raton, FL. 33487

AMS1140 External Photos Front AMS1140 Back

FCC ID: BVCAMS1140 IC: 3506A-AMS1140 FCC ID: BVCAMS1140 IC: 3506A-AMS1140

FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Regulatory Label

55 44 33 22 11 D D C C B B A A VCC_12V VCC_12V TitleSize Document Number Rev Date: Sheet of APPD BY DATE DESCRIPTION PCN NO. LTR DrawnCheckedEngrAppdRelease DATE APPROVALS Sensormatic Electronics Corp. S0312-3089-01 A ALARM, LOW COST DETECTION B 11 Thursday, November 05, 2009 A REL PER ER PS 201854 PS 05-NOV-09 (NAME)PSPS(NAME)(NAME) (21-JUL-09)(DD-MMM-YY)(21-JUL-09)(DD-MMM-YY)(DD-MMM-YY) 6600 CONGRESS AVENUEBOCA RATON, FLORIDA 33487 TitleSize Document Number Rev Date: Sheet of APPD BY DATE DESCRIPTION PCN NO. LTR DrawnCheckedEngrAppdRelease DATE APPROVALS Sensormatic Electronics Corp. S0312-3089-01 A ALARM, LOW COST DETECTION B 11 Thursday, November 05, 2009 A REL PER ER PS 201854 PS 05-NOV-09 (NAME)PSPS(NAME)(NAME) (21-JUL-09)(DD-MMM-YY)(21-JUL-09)(DD-MMM-YY)(DD-MMM-YY) 6600 CONGRESS AVENUEBOCA RATON, FLORIDA 33487 TitleSize Document Number Rev Date: Sheet of APPD BY DATE DESCRIPTION PCN NO. LTR DrawnCheckedEngrAppdRelease DATE APPROVALS Sensormatic Electronics Corp. S0312-3089-01 A ALARM, LOW COST DETECTION B 11 Thursday, November 05, 2009 A REL PER ER PS 201854 PS 05-NOV-09 (NAME)PSPS(NAME)(NAME) (21-JUL-09)(DD-MMM-YY)(21-JUL-09)(DD-MMM-YY)(DD-MMM-YY) 6600 CONGRESS AVENUEBOCA RATON, FLORIDA 33487 P1HDR2106-0072-01P1HDR2106-0072-01 124 DS18 LED RED 4821-0054-01 DS18 LED RED 4821-0054-01 1 2 DS13 LED RED 4821-0054-01 DS13 LED RED 4821-0054-01 1 2 DS7 LED RED 4821-0054-01 DS7 LED RED 4821-0054-01 1 2 DS5 LED RED 4821-0054-01 DS5 LED RED 4821-0054-01 1 2 DS14 LED RED 4821-0054-01 DS14 LED RED 4821-0054-01 1 2 DS16 LED RED 4821-0054-01 DS16 LED RED 4821-0054-01 1 2 DS3 LED RED 4821-0054-01 DS3 LED RED 4821-0054-01 1 2 DS19 LED RED 4821-0054-01 DS19 LED RED 4821-0054-01 1 2 DS10 LED RED 4821-0054-01 DS10 LED RED 4821-0054-01 1 2 DS1 LED RED 4821-0054-01 DS1 LED RED 4821-0054-01 1 2 DS15 LED RED 4821-0054-01 DS15 LED RED 4821-0054-01 1 2 DS8 LED RED 4821-0054-01 DS8 LED RED 4821-0054-01 1 2 DS11 LED RED 4821-0054-01 DS11 LED RED 4821-0054-01 1 2 DS17 LED RED 4821-0054-01 DS17 LED RED 4821-0054-01 1 2 DS20 LED RED 4821-0054-01 DS20 LED RED 4821-0054-01 1 2 DS4 LED RED 4821-0054-01 DS4 LED RED 4821-0054-01 1 2 R1120R1120 DS6 LED RED 4821-0054-01 DS6 LED RED 4821-0054-01 1 2 DS12 LED RED 4821-0054-01 DS12 LED RED 4821-0054-01 1 2 DS2 LED RED 4821-0054-01 DS2 LED RED 4821-0054-01 1 2 DS9 LED RED 4821-0054-01 DS9 LED RED 4821-0054-01 1 2

FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Page 1 of 33 TYCO SAFETY PRODUCTS SENSORMATIC EMC TEST REPORT Model: AMS-1140 FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Intentional Radiator FCC and IC 47 CFR, Part 15, Subpart B, AND Subpart C Industry Canada RSS GENe, ICES-003e, RSS-210e Date: January 22, 2010 EMC Engineer FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Page 2 of 33 1 SUMMARY OF RESULTS 1.1 47 CFR Part 15, Subpart B / Subpart C Part PARAMETER TO BE MEASURED Applies Comments SubPart B, Unintentional Radiators (Class B) 15.107 Conducted Disturbance (Conducted Emissions, 0.15-30 MHz) X Complies 15.109 Radiated Disturbance (Radiated Emissions, 30-1000 MHz) X Complies SubPart C, Intentional Radiators (General Limits) 15.207 Conducted Disturbance (Conducted Emissions, 0.15-30 MHz) X Complies 15.209 Radiated Disturbance (Radiated Emissions, 0.009 plus MHz) X Complies Compliance with 15.203: This product is professionally installed and setup, therefore the device is compliant with the requirement of this clause. Compliance with 15.204: The only antenna type used with this transmitter is a loop. The loop with the highest gain (area x turns x current) has been used for testing and the transmit circuit adjusted for highest output. 1.2 IC RSS 210 (RSS GEN) Clause PARAMETER TO BE MEASURED Applies comment 4.6.1 Emission Bandwidth X Complies FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Page 3 of 33 2 Table of Contents 1 SUMMARY OF RESULTS ................................................................................................................ 2 1.1 47 CFR Part 15, Subpart B / Subpart C ........................................................................................ 2 1.2 IC RSS 210 (RSS GEN) .............................................................................................................. 2 2 Table of Contents ................................................................................................................................ 3 3 DESCRIPTION AND CHARACTERISTICS OF THE EUT ............................................................. 4 3.1 Description and Characteristics of Equipment Under Test (EUT). .............................................. 4 3.1.1 Additional EUT Setup / Configuration Details ..................................................................... 4 3.1.2 Type Designation ................................................................................................................... 4 3.2 CONSTRUCTION OF EQUIPMENT UNDER TEST (EUT) ..................................................... 5 3.2.1 Overview ............................................................................................................................... 5 3.2.2 Installation ............................................................................................................................. 5 3.3 EQUIPMENT RATINGS ............................................................................................................. 6 3.3.1 Frequency Characteristics And Internal Clocks .................................................................... 6 3.3.2 Marketing And Installation Environment .............................................................................. 6 3.4 TEST SET-UP BLOCK DIAGRAM ............................................................................................ 7 3.4.1 List Of Ports .......................................................................................................................... 7 3.1 Sample Calculation – Radiated & Conducted Emissions ............................................................. 8 3.2 Test Site Registration .................................................................................................................... 8 3.1 Uncertainty of Measurements ....................................................................................................... 9 4 FCC TESTS ....................................................................................................................................... 10 4.1.1 Conducted Emissions, FCC Part 15, Clause 15.107 And 15.207 ....................................... 10 4.1.2 Radiated Emissions, FCC Part 15, Clause 15.109 (above 30 MHz) .................................. 12 4.1.3 Radiated Emissions, FCC Part 15, Clause 15.209 (below 30 MHz) .................................. 14 4.1.4 Occupied Bandwidth For Industry Canada – IC. RSS GEN, sec 4.6.1 ............................... 16 5 EQUIPMENT LIST ........................................................................................................................... 24 6 ANTENNA FACTORS. .................................................................................................................... 25 FCC ID: BVCAMS1140 IC: 3506A-AMS1140 Page 4 of 33 3 DESCRIPTION AND CHARACTERISTICS OF THE EUT 3.1 Description and Characteristics of Equipment Under Test (EUT). Unit: AMS-1140 Product Code: ZA1140-D Part Number: Regulatory ID: AMS1140 3.1.1 Additional EUT Setup / Configuration Details Configurator: Application: Application Build: Boot Utility Version: 3.1.2 Type Designation The type designation may be either a single alphanumeric code or an alphanumeric/code divided into two parts. TYPE DESIGNATION AS A SINGLE ALPHANUMERIC CODE: (See Note 1) A M S - 1 1 4 0 OR TYPE DESIGNATION IN TWO PARTS: 1. EQUIPMENT SERIES No. (See Note 2) 2. EQUIPMENT SPECIFIC No. (See Note 3) Note 1: This is the manufacturer’s numeric or alphanumeric code or name that is specific to a particular equipment. It may contain information in coded form on the characteristics of the equipment e.g. frequency, power. The manufacturer is free to choose the form of the type designation. Note 2: This is the number, code or trade name used by the manufacturer to describe a series or “family” of equipment of substantially the same mechanical and electrical construction which will include a number of related equipments. This number is often referred to as …

Text truncated - open the document above for the full version.

AMS1140 1 Photos of Test Setups 1.1 H-field testing on south parking lot. AMS1140 1.2 E-field testing on OATS AMS1140 1.3 Conducted Emissions LISN is out of photo. AMS1140 1.4 Occupied Bandwidth AMS1140