BVCUMEXCALAnti Theft Device

Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 1 of 13 AMS-1070 Controller Installation Guide ZEDEX-1070 Contents About this Guide ................................................ 1 About the Product .............................................. 2 Installation Requirements .................................. 2 Installing the Controller ...................................... 4 Connecting the Antennas and Remote Alarm Module ............................................................... 5 Connecting a tall and a short antenna ........ 5 Connecting two short antennas and a remote alarm module .............................................. 5 Connecting a split-receiver (dual-aisle) configuration................................................ 6 Connecting the Noise Canceling Antennas ....... 6 Connecting to Relays in the Controller .............. 6 Connecting Power to the Controller................... 7 Connecting a Service Laptop to the Controller.. 7 Connecting a Modem to the Controller.............. 8 Connecting a Controller to an RS-485 Network 9 Connecting a Modem to an RS-485 Network .. 10 Specifications................................................... 10 Declarations ..................................................... 13 Regulatory Compliance ............................. 13 Other Declarations .................................... 13 © Sensormatic 2002 About this Guide This installation guide explains how to install the controller for an AMS-1070 system. This document only describes how to install the controller and connect the antenna cables. Information on how to mount the antennas is in the antenna documents. Other related documents are: • Install Guide, AMS-1070 Antenna, P/N 8200- 0127-01 • Quick Install Guide, AMS-1070 Remote Alarm Module, P/N 8200-0127-02 • Installation Guide, Digital 216 Noise Coils 8000- 2693-05 • Quick Install Guide, AMS-1070 Antenna Flush- Mount Brackets, P/N 8200-0127-07 • Quick Install Guide, AMS-1070 Antenna Cantilever-Mount Brackets, P/N 8200-0127-08 • Quick Install Guide, AMS-1070 Antenna Pole- Mount Brackets, P/N 8200-0127-09 • Installation Guide, AMS-1070 Controller EMI Shield 8200-0127-12 • Installation Guide, AMS-1070 Controller Under Counter Installation Guide 8200-0127-13 • Installation Guide, AMS-1070/ScanMax Pro Deactivator Mounting Plate 8200-0127-14 Note: Because customer requirements dictate the placement of system components, your Sensormatic representative will supply this information separately. Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 2 of 13 About the Product An AMS-1070 controller is part of an Ultra•Max ® security label detector. The controller powers and controls up to four transceiver antennas, two optional remote alarm modules, and two noise canceling antenna kits. Figure 1 shows the system components. Figure 1. System components Installation Requirements Verifying Equipment and Unpacking ❑ Verify that all equipment has arrived. Make sure the system configuration is the right one for the installation site. ❑ Unpack major components in a back room. At the install site, lay out parts in the order you will need them. Do not clutter the aisle or cause a trip hazard. Installer/Contractor ❑ Shall have electrical work comply with the latest national electrical code, national fire code, and all applicable local codes and ordinances. ❑ Shall coordinate all work with other trades to avoid interference. ❑ Shall verify existing site conditions and coordinate with the owner’s representative and appropriate utilities as required. ❑ Shall obtain copies of all related plans, specifications, shop drawings and addenda to schedule and coordinate related work. ❑ Shall thoroughly review the project to ensure that all work meets or exceeds the above requirements. Any alleged discrepancies shall be brought to the attention of Sensormatic Electronics. ! WARNING! Do not install this product in hazardous areas where highly combustible or explosive products are stored or used. Site Requirements Refer to Figure 2 for description of site requirements and placement considerations. ❑ Connect the controller to a 100-240Vac source. No fuse exchange is required for the controller. ❑ Use the appropriate power cord based on the country of use. ❑ Replace the controller’s slow-blow fuses only with a fuse of the same type and rating. Tools and Equipment Required For all controller installations: • Phillips and slotted screwdrivers • Wire strippers • Cordless drill and phillips-head screwdriver bits Ranger Remote Alarm Module Controller Antenna Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 3 of 13 Figure 2. Component placement constraints Ref Description Distance Reason [a] Controller to antenna separation 9m (30ft) max Tx/Rx cable length [b] Controller to ranger separation 12m (40ft) max Ranger cable length [c] Controller to remote alarm unit separation 9m (30ft) max Remote alarm unit cable length [d] Controller to power outlet separation 2.3m (7.5’) max (USA) 2.5m (8’) max (non-USA) Length of power cord [e] Space around all sides of controller 20cm (8in) min Ventilation. May be mounted on shelf or wall. May be hidden (e.g. checkout counter, backroom, basement). [a] [b] [c] [d] [e] Controller Ranger Antenna Power cord options P/N 0351-0547-0x -01 USA -02 Schuko -03 UK -04 Japan -05 USA line filter -07 Australia Power Outlet Voltage Range: 100-240Vac (50-60Hz) Type: Three-wire, unswitched. Do not use orange outlets; they are dedicated to computer equipment). Availability 24 hours Grounding: < 0.5Vac between neutral and ground Loading: Cannot share line with neon signs, motors, computers, cash registers, terminals or data communications equipment. Power outlet Preliminary AMS-1070 CONTROLLER INSTALLATION GUIDE (8200-0127-06, REV. 0) 4 of 13 Installing the Controller The controller can be mounted on a wall or rest on a shelf (no mounting procedure required). • To mount the controller…

Text truncated - open the document above for the full version.

UM EXCAL External Photo

UM EXCAL Label Sample BARCODE PRODUCT CODE: AMS-1070 REG ID: UM EXCAL-PP MFD:7-02 P/N: 0319-0004-01 REV : A SERIAL NO: SECA0117012345 RATING: 100-240V~ 50-60Hz 1.0A MADE IN PUERTO RICO FCC ID: BVCUMEXCAL THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. IC: 3506A-UMEXCAL N205 â NRTL

UM EXCAL Label Location Regulatory Label

UM EXCAL Internal Photos Controller, Cover Off Connector View Tall Antenna Short Antenna Controller Printed Circuit Board Assembly, Top View Printed Circuit Board Assembly, Bottom View

FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 1 Appendix III Test Report Cover Sheet/Performance Test Data MODEL NUMBER: UM EXCAL-PP MANUFACTURER: Sensormatic Electronics Corp. TESTED TO RADIO STANDARD SPECIFICATION NO.: RSS 210 OPEN AREA TEST SITE INDUSTRY CANADA NUMBER: IC 3506 FREQUENCY RANGE (or fixed frequency): 58 kHz R.F. POWER IN WATTS: n/a FIELD STRENGTH (at what distance): 29 dBuV/m @ 300 m OCCUPIED BANDWIDTH (99% BW): 4 kHz TYPE OF MODULATION: pulse EMISSION DESIGNATOR (TRC-43): 4K00P0N TRANSMITTER SPURIOUS (worst case): -6 dBuV/m@300m RECEIVER SPURIOUS (worst case): see transmitter ATTESTATION: DECLARATION OF COMPLIANCE : I declare that the testing was performed or supervised by me; that the test measurements were made in accordance with the above mentioned department standard(s), and that the radio apparatus identified in this application has been subject to all the applicable test conditions specified in the departmental standards and all of the requirements of the standard have been met. Signature: Date: October 3,2002 NAME AND TITLE (Please print or Type): Donald J. Umbdenstock Senior Principal Engineer, Compliance Engineering Note : This form must be completed and provided with the submission. FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 2 COMPANY Sensormatic Electronics Corp. 6600 Congress Ave Boca Raton, Florida PRODUCT TESTED UM EXCAL-PP FCC ID: BVCUMEXCAL IC: 3506A-UMEXCAL FCC RULES 15.207, 15.209 IC SPECIFICATIONS RSS 210 TEST DATE September 18 – October 3, 2002 SUBMITTED BY Donald J. Umbdenstock FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 3 INDEX I. SUMMARY OF RESULTS 4 II. GENERAL INFORMATION 4 Test Methodology 4 Test Facility 4 System Description 5 15.203 Compliance 5 III. CONDUCTED EMISSIONS TESTING, 47 CFR 15.207 5 IV. RADIATED EMISSIONS TESTING, 47 CFR 15.209 6 V. OCCUPIED BANDWIDTH, RSS 210, Clause 5.9.1 6 VI. LIST OF MEASUREMENT EQUIPMENT 7 VII. DATA 8 Part A – Conducted Emissions 8 Part B – Radiated Emissions 9 Part C – 20 dB Bandwidth 10 FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 4 I. Summary of Results 47 CFR 15.207 CONDUCTED EMISSIONS COMPLIES 47 CFR 15.209 RADIATED EMISSIONS COMPLIES RSS 210: 5.9.1 OCCUPIED BANDWIDTH PROVIDED II. General Information 1.1 Test Methodology Both conducted and radiated emissions testing were performed according to the procedures in ANSI C63.4-1992, and the requirements of 15.31, 15.33, 15.35, 15.207, and 15.209. Radiated emissions measurements below 30 MHz were performed at a distance of 10 meters and the results extrapolated to the distance specified per 15.31 and 15.209. 1.2 Test Facility Measurements per 15.207 and 15.209 were performed at Sensormatic Electronics Corporation. The shielded room conducted emissions measurement facility and the radiated emissions Open Area Test Site are located at Sensormatic Electronics Corporation Headquarters at 6600 Congress Avenue, Boca Raton, Florida 33487. These sites have been found acceptable by and are on file with the FCC per FCC Registration Number 90925, and Industry Canada per file number IC 3506. FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 5 1.3 Test System Description. The system consists of an electronics unit (power pack) that houses the transmitter, receiver, alarm and data processing circuitry. The antenna is contained in a plastic enclosure in the shape of a sword sheath. It consists of a multi-turn loop antenna wound on a permeable core. The product tested was a pre-production unit built to production drawings. 15.203 . The antenna is an external antenna unique to the system requirements. It is connected to the power pack by means of a cable that is permanently attached to the antenna. The other end of the cable is fitted with a connector pinned specific to our application making it unique, therefore the antenna is compliant with the requirements of this clause. III. Conducted Emissions 15.207. Conducted emissions data are presented in Section VII “Data”, Part A, Conducted Emissions. The product demonstrated compliance with the requirements. The product was tested at 120 V, 60 Hz. FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 6 IV. Radiated Emissions 15.209. Radiated emissions data for this product are presented in Section VII “Data”, Part B, Radiated Emissions. The product demonstrated compliance with the requirements. Radiated emissions measurements were performed at 5 meters. Propagation loss was determined by extrapolating the results to 300 meters as per 15.31(f)(2), using the square of the inverse linear distance extrapolation as indicated in the rules. Maximum radiation was determined by first assessing symmetry while applying incremental rotation of the product. The product exhibited quadrant symmetry. Measurements were taken at radials of 22.5° throughout one quadrant; the measurement antenna was rotated for maximum pickup about the vertical and horizontal axis of the measurement antenna at each radial. The maximum emission was determined to be with the measurement loop antenna in the vertical polarization, parallel to the plane of the transmit antenna pair. The product was tested at input voltages to the transformer ranging from 102 – 138 V, 60 Hz with no significant change in transmitter output. See Section VII, Part B. V. Occupied Bandwidth RSS 210:5.9.1. The 20 dB bandwidth measurements for this product are presented in Section VII “Data”, Part C, Occupied Bandwidth. A bandwidth requirement was not specified for 58 kHz products, so the default 20 dB bandwidth was measured. The HP 8591EM spectrum analyzer cannot measure a bandwidth over 1.8 kHz in quasi-peak detection mode, so the bandwidth was measured in peak detection mode, providing a worst case occupied bandwidth. FCC ID: BVCUMEXCAL IC: 3506A UMEXCAL 7 VI. LIST OF MEASURING EQUIPMENT The equipment used for determining compliance of the Ultra Post system with the requirements of 15.207 and 15.209 is marked with an “X” in the first column of the table below. Model Description Vendor Serial # X ALP -70 Loop Antenna Electro Metrics 163 3110B Biconnical…

Text truncated - open the document above for the full version.

Set-Up Photos Conducted Emissions Conducted Emissions Radiated Emissions Set-Up