CASTBCK4ABase Station Transceiver

TB9400 Installation and Operation ManualInstallation73 © Tait Limited March 2015 5Installation This chapter provides information on the site requirements for your TB9400 equipment and also describes how to install the base station in a standard 19 inch rack or cabinet. If this is your first time installing a TB9400 base station, we recommend that you read the entire chapter before beginning the actual installation. 74InstallationTB9400 Installation and Operation Manual © Tait Limited March 2015 5.1Before You Begin 5.1.1Equipment Security The security of your base station equipment is a high priority. If the site is not fully secure, the base station should at least be locked in a secure cabinet to prevent unauthorized access. 5.1.2Grounding and Lightning Protection Electrical GroundThe base station modules are grounded by physical contact between the module case and the subrack. To ensure a good ground connection you must tighten each module retaining clamp securely (refer to “Final Reassembly” on page 118 for the correct torque). A threaded grounding connector is provided on the rear of the subrack for connection to the site ground point (refer to “Connecting Up the Base Station” on page 95 for more details). Lightning GroundIt is extremely important for the security of the site and its equipment that you take adequate precautions against lightning strike. Because it is outside the scope of this manual to provide comprehensive information on this subject, we recommend that you conform to your country’s standards organization or regulatory body. 5.1.3Equipment Ventilation Always ensure there is adequate ventilation around the base station. NoticeDo not operate it in a sealed cabinet. You must keep the ambient temperature within the specified range, and we strongly rec- ommended that you ensure that the cooling airflow is not restricted. NoticeThe cooling fans are mounted on the front panel and will only operate when the panel is fitted correctly to the front of the subrack. To ensure adequate airflow through the base station, do not operate it for more than a few minutes with the front panel removed (e.g. for servicing purposes). 5.1.4Ambient Temperature Sensor The ambient temperature reading for the base station is provided by the temperature sensor located on the front panel circuit board. TB9400 Installation and Operation ManualInstallation75 © Tait Limited March 2015 5.1.5Cabinet and Rack Ventilation The cooling airflow for the base station enters through the front panel and exits at the rear of the subrack. For optimum thermal performance, the heated air that has passed through a base station must not be allowed to re- enter the air intakes on the front panel. Any space at the front of the cabinet not occupied by equipment should be covered by a blanking panel. Refer toFigure 5.1 on page 76. To allow enough cooling airflow through a cabinet-mounted base station, we recommend the following: ■an area of at least 23 in 2 (150 cm 2 ) of unrestricted ventilation slots or holes in front of the air intakes for the fans for each subrack; for example, thirty 0.25 x 3.3 in (6 x 85 mm) slots will allow the recommended airflow ■a vent in the top of the cabinet with an area of approximately 23 in 2 (150 cm 2 ) per subrack, or a similar area of ventilation per subrack at the rear of the cabinet behind each subrack ■a 2 U gap at the top of the cabinet. NoticeThe ventilation opening must be unrestricted. If the slots or holes are covered with a filter, mesh or grille, the open area must be increased to allow the same airflow as an unrestricted opening. The maximum ambient temperature entering the cabinet must not exceed + 140°F (+ 60°C). If you are installing multiple subracks in a cabinet, ensure that there will be enough cooling airflow through the cabinet after the equipment has been installed. For example, the recommended maximum number of subracks in a 38 U cabinet is five, as shown in Figure 5.1 on page 76. If the base station is installed in a rack or cabinet with other equipment with different ventilation requirements, we recommend that the base station be positioned below this equipment. Auxiliary Extractor Fans The base station does not require auxiliary extractor fans mounted in the top of the cabinet. If your cabinet is already fitted with fans, the following procedures apply: ■if there are six or more 4.75 in (12 cm) fans, each capable of extracting 94.2 ft 3 per minute (160 m 3 per hour), they must run continuously ■if there are fewer than six fans, you must remove them and ensure the vent in the top of the cabinet has an area of approximately 23 in 2 (150 cm 2 ) per subrack. If you have any other configuration, the performance of your system will depend on how closely you comply with the base station airflow requirements described above. 76InstallationTB9400 Installation and Operation Manual © Tait Limited March 2015 Figure 5.1Typical cabinet ventilation requirements b ventilation slots d airflow entry c blanking panels e airflow exit path 8in (20 cm) 2U ≥7in (≥17.5cm) side viewfront view top view c c d e b TB9400 Installation and Operation ManualInstallation77 © Tait Limited March 2015 5.2Unpacking and Moving the Subrack The subrack is packed in a strong corrugated cardboard carton with top and bottom foam cushions. To prevent personal injury and damage to the equipment, we recommend that two people unpack and move the subrack. To remove the subrack from the carton, follow the procedure illustrated in Figure 5.2. CautionA subrack complete with modules can weigh up to 46 lb (21 kg), or up to 53 lb (24 kg) complete with packaging. We recommend that you have another person help you unpack and move the equipment. The TBAA03-16 carrying handles will make it easier to move the equipment once it has been unpacked. If necessary, remove the modules from the subrack before moving it (refer to “Replacing Modules” on page 107). In all cases follow safe lifting practices. 1.Cut the tape securing…

Text truncated - open the document above for the full version.

TB9400 Base Station Installation and Operation Manual MBC-00001-09 · Issue 9 · March 2015 2TB9400 Installation and Operation Manual © Tait Limited March 2015 Contact Information Tait Communications Corporate Head Office Tait Limited P.O. Box 1645 Christchurch New Zealand For the address and telephone number of regional offices, refer to our website: www.taitradio.com Copyright and Trademarks All information contained in this document is the property of Tait Limited. All rights reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated, stored, or reduced to any electronic medium or machine-readable form, without prior written permission from Tait Limited. The word TAIT and the TAIT logo are trademarks of Tait Limited. All trade names referenced are the service mark, trademark or registered trademark of the respective manufacturers. Disclaimer There are no warranties extended or granted by this document. Tait Limited accepts no responsibility for damage arising from use of the information contained in the document or of the equipment and software it describes. It is the responsibility of the user to ensure that use of such information, equipment and software complies with the laws, rules and regulations of the applicable jurisdictions. Enquiries and Comments If you have any enquiries regarding this document, or any comments, suggestions and notifications of errors, please contact your regional Tait office. Updates of Manual and Equipment In the interests of improving the performance, reliability or servicing of the equipment, Tait Limited reserves the right to update the equipment or this document or both without prior notice. Intellectual Property Rights This product may be protected by one or more patents or designs of Tait Limited together with their international equivalents, pending patent or design applications, and registered trade marks: NZ 409837, NZ 409838, NZ 415277, NZ 415278, NZ 508806, NZ 516280/NZ 519742, NZ 521450, NZ 524369, NZ 524378, NZ 524509, NZ 524537, NZ 530819, NZ 534475, NZ 547713, NZ 569985, NZ 577009, NZ 579051, NZ 579364, NZ 584534, NZ 586889, NZ 592624, NZ 593887, NZ 593888, NZ 600346, NZ 607046, NZ 610426, NZ 610563, NZ 615954, NZ 625717, NZ 628342, NZ 629167, NZ 630718, NZ 700387, NZ 700908, NZ 70177, AU 2004216984, AU 321864, AU 321868, AU 339127, AU 339391, CN 1031871, CN 1070368, CN 200930004199.5, CN 200930004200.4, CN 200930009301.0, EU 000915475-0001, EU 000915475-0002, GB 2413445, US 8301682, US 13/542147, US 13/ 896969, US 14/032876, US 14/495334, US 29/401234, US 29/401235, US 5745840, US 640974, US 640977, US 7411461, US 7758996, US 7937661, US 8902804. This product may also be made under license under one or more of the following U.S. Patents: 5,146,497, 5,148,482, 5,164,986, 5,185,795, 5,185,796, 5,271,017, 5,377,229 and 5,502,767. The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. Protected by U.S. Patents 5,870,405, 5,826,222, 5,754,974, 5,701,390, 5,715,365, 5,649,050, 5,630,011, 5,581,656, 5,517,511, 5,491,772, 5,247,579, 5,226,084 and 5,195,166. Environmental Responsibilities Tait Limited is an environmentally responsible company which supports waste minimization, material recovery and restrictions in the use of hazardous materials. The European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive requires that this product be disposed of separately from the general waste stream when its service life is over. For more information about how to dispose of your unwanted Tait product, visit the Tait WEEE website at www.taitradio.com/weee. Please be environmentally responsible and dispose through the original supplier, or contact Tait Limited. Tait Limited also complies with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive in the European Union. In China, we comply with the Measures for Administration of the Pollution Control of Electronic Information Products. We will comply with environmental requirements in other markets as they are introduced. TB9400 Installation and Operation Manual3 © Tait Limited March 2015 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Scope of Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Associated Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Publication Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.2 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.3 Mechanical Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.4 Frequency Bands and Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1.5 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .…

Text truncated - open the document above for the full version.

Tait TBCK4A- Part 90R Application Review Public Safety Bands: 764-776 MHz and 794-806 MHz 1. Explanation of which Narrowband or Wideband channel segments the device is capable of supporting from those listed in 90.531(b), and 90.531(c). - For Narrowband segments: a) Is the device capable of operating on “General Use” channels listed in 90.531(b)(5) or “State”channels listed in 90.531(b)(6)? Yes, Transmit Channels 1-960, Receive Channels 961-1920 b) Is the device ONLY capable of operating on Low Power “Regional” channels listed in 90.531(b)(3) or Low Power “Itinerant” channels listed in 90.531(b)(4)? No c) Is the device capable of operating on “Nationwide” Interoperability channels listed in 90.531(b)(1)? Yes - For Wideband segments: d) Is the device capable of operating on Interoperability channels listed in 90.531(c)(1)? No 2. Statement regarding the modulation capabilities of the device: - Does the device support digital Voice only, Data only, or both [see 90.547]? Not Applicable, not a mobile or portable - Does the device support analog voice operation [see 90.535(a)]? No 3. Verify the following Interoperability Channel Operation requirements listed in 90.531 and 90.547 for Narrowband mobile, portable, or control devices only, given the information from #1. and #2. above: a) Designed for Data ONLY Operation on Nationwide, General Use or State channels - Must be capable of operating on the data interoperability channels listed in 90.531(b)(1)(i). b) Designed for Voice ONLY Operation on Nationwide, General Use or State channels - Must be capable of operating on the nationwide and calling only interoperability channels listed in 90.531(b)(1) and (b)(1)(ii), but do not have to operate on data only channels listed in 90.531(b)(1)(i). c) Designed for BOTH Voice and Data Operation on Nationwide, General Use or State channels - Must be capable of operating on all nationwide interoperability channels including data only and calling only channels listed in 90.531(b)(1), (b)(1)(i), and (b)(1)(ii). d) Designed for Low Power ONLY Operation on Regional/Itinerant channels – Must operate ONLY on the data/voice channels listed in 90.531(b)(3) or (b)(4). Not applicable, equipment category is base station equipment 4. Verify the following capability requirements for all Wideband devices only, given the information from #1. and #2. above: a) Designed for Data ONLY Operation on Nationwide Interoperability channels - Must operate on the wideband data interoperability channels listed in 90.531(c)(1). Not Applicable, not designed for Wideband 5. Application filing requirements for Narrowband mobile, portable or control devices only: - Voice Operation on General Use, State, or Nationwide Voice Interoperability channels: a) Emission limitation (ACP) compliance for each combination of channel bandwidth and modulation for all band plans - 90.543. b) Attestation of voice path efficiency compliance for operation on General Use and State channels only – 90.203(m) & 90.535(d). c) Attestation of operation on Nationwide Voice Interoperability and Calling Only channels – 90.547. - For Voice Only devices, attestation to 90.547(a)(3). d) Attestation of compliance to Project 25 FDMA Common Air Interface (ANSI 102) standards for operation on Nationwide Voice Interoperability and Calling Only channels only - 90.548(a)(1). e) Frequency stability compliance for all band plans - 90.539(a) & (c). f) Transmitting power compliance for all band plans - 90.541(b) & (c). - Data Operation on General Use, State, or Nationwide Data Interoperability channels: g) Emission limitation (ACP) compliance for each combination of channel bandwidth and modulation for all band plans - 90.543. h) Attestation of data rate efficiency compliance for General Use and State channels only - 90.535(b). i) Attestation of operation on Nationwide Data Interoperability channels listed in 90.531(b)(1)(i) only – 90.547. - For Data Only devices, attestation to 90.547(a)(2). j) Attestation of compliance to Project 25 Data Overview (ANSI 102) standards for operation on data interoperability channels listed in 90.531(b)(1)(i) only - 90.548(a)(2). k) Frequency stability compliance for all band plans - 90.539(a) & (c). l) Transmitting power compliance for all band plans - 90.541(b) & (c). - Low Power Operation (mobiles and portables only) on Regional/Itinerant channels: m) Emission limitation (ACP) compliance for each combination of channel bandwidth and modulation for all Low Power channel band plans - 90.543. n) Attestation of low power ONLY operation on Low Power Regional/Itinerant channels listed in 90.531(b)(3)&(b)(4) – 90.541(b)&(c). - For Low Power Only devices, attestation to 90.547(a)(1). o) Attestation of data rate efficiency compliance for (non-voice) data capable devices operating on Low Power Regional/Itinerant channels only - 90.535(b). [data efficiency applies to all (non-voice) narrowband channels] p) Frequency stability compliance for all band plans - 90.539(c). q) Transmitting power compliance for all band plans - 90.541(d). Not applicable, equipment category is base station equipment 6. Application filing requirements for Wideband mobile, portable, or control devices only: - Data Operation: a) Emission limitation (ACP) compliance for each combination of channel bandwidth and modulation for all band plans - 90.543. b) Attestation of data rate efficiency compliance for wideband data channels listed in 90.531(c) - 90.535(c). [data efficiency applies to all (non-voice) wideband channels] c) Attestation of Data Interoperability Channel operation for wideband data interoperability channels listed in 90.531(c)(1) only. d) (future) Attestation of compliance to Wideband Data (ANSI 902) standards - for data interoperability channels listed in 90.531(c)(1) only - 90.548(??). e) Frequency stability compliance for all band plans - 90.539. f) Transmitting power compliance for all band plans - 90.541. Not applicable, not designed for Wideband 7. All devices – oth…

Text truncated - open the document above for the full version.

Tait Limited Phone: +64 3 358 1026 PO Box 1645, 558 Wairakei Road Fax: +64 3 358 9299 Burnside, Christchurch 8053 www.taitradio.com New Zealand 13 May 2015 Request for Confidentiality FCC ID: CASTBCK4A In accordance with 47 C.F.R. Section 0.457 and 0.459, we Tait Limited, hereby request confidentiality for the Tuneup Procedure, Schematics, Parts List, Operational Description and Technical Description presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. David Jackson Test Laboratory Services Manager Tait Limited

Tait Limited Phone: +64 3 358 1026 PO Box 1645, 558 Wairakei Road Fax: +64 3 358 9299 Burnside, Christchurch 8053 www.taitradio.com New Zealand F.C.C. Justification Letter FCC ID: CASTBCK4A To meet the requirements of Federal Communications Commission (F.C.C.) publication, KDB634817 - Frequency Range Listings for Certification Grants, Tait Electronics Limited submits the following attestation. This base station transceiver has: 1. The design capability to operate in the frequency band 762-870 MHz. 2. Complies with 47CFR Part 90.203(e) in that the equipment operator cannot directly program transmit frequencies using the normally accessible external controls. Programming this equipment is the responsibility of Tait Limited approved Service Agents In addition to the following rule parts applied for: Part 22, 90 This device may be utilised in systems operated by Non Federal and Public Safety agencies, as indicated in the table beneath. The Grant Note ‘EF’ should be appended to the Grant of Authorisation, indicating this operation is required. Table 1 – Frequency Range and Rule Parts - (47CFR Part 2.106) Freq. Range (MHz) Part 22 Part 90 763-775 F/NF 775-793 793-805 F/NF 805-806 806-809 F/NF 809-849 F/NF F/NF 849-851 F/NF 851-854 F/NF 854-894 F/NF F/NF F=Federal Agency NF=Non Federal Agency Des Fox Compliance Coordinator Christchurch 4 th June 2015

Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 1 of 10 Tait Limited External Photographs Exhibit (May 2015) Product: TB9400 Type code: TBCK4A FCC ID: CASTBCK4A IC: 737A-TBCK4A Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 2 of 10 Photograph 01: 50W System – Product view Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 3 of 10 Photograph 02: 50W System – Front panel Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 4 of 10 Photograph 03: 50W System – Rear view Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 5 of 10 Photograph 04: 50W System – Internal view Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 6 of 10 Photograph 05: 50W PA module – Product view Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 7 of 10 Photograph 06: 50W PA module – Front panel Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 8 of 10 Photograph 07: 50W PA module – Rear panel Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 9 of 10 Photograph 08: Reciter module (762-870MHz) – Front panel Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 10 of 10 Photograph 09: Reciter module (762-870MHz) – Rear panel

Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 1 of 3 Tait Limited Compliance Label Photograph Exhibit (May 2015) Product: TB9400 Type code: TBCK4A FCC ID: CASTBCK4A IC: 737A-TBCK4A Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 2 of 3 Photograph 01: 50W System (762 Æ 870MHz) – Product ID label Photograph 02: Reciter module (762 Æ 870MHz) – Compliance label Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 3 of 3 Photograph 03: 50W PA module (762 Æ 870MHz) – Compliance label

Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 1 of 14 Tait Limited Internal Photographs Exhibit (May 2015) Product: TB9400 Type code: TBCK4A FCC ID: CASTBCK4A IC: 737A-TBCK4A Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 2 of 14 Photograph 01: 50W PA modules – Internal view Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 3 of 14 Photograph 02: 50W PA modules – Top. Shields Removed Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 4 of 14 Photograph 03: 50W PA modules - Bottom Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 5 of 14 Photograph 04: Rx PCB - Top Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 6 of 14 Photograph 05: Rx PCB – Top. Shields Removed Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 7 of 14 Photograph 06: Rx PCB – Bottom. Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 8 of 14 Photograph 07: Control PCB – Top Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 9 of 14 Photograph 08: Control PCB – Top. Shields Removed Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 10 of 14 Photograph 09: Control PCB – Bottom Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 11 of 14 Photograph 10: TXF PCB – Top Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 12 of 14 Photograph 11: TXF PCB – Top. Shields Removed Photograph 12: TXF PCB – Bottom. Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 13 of 14 Photograph 13: TXR PCB – Top Photograph 14: TXR PCB – Top. Shields Removed Tait Limited 535 Wairakei Road, Christchurch 8053 PO Box 1645 CHCH New Zealand +64 3 358 3399, www.taitradio.com Page 14 of 14 Photograph 15: TXR PCB – Bottom.

TELTEST Laboratories Tait Ltd Report Number 3646 FCC ID: CASTBCK4A Page 1 of 74 Report Revision: 1 IC : 737A-TBCK4A Issue Date: 18-May-2015 LABORATORY TEST REPORT RADIO PERFORMANCE MEASUREMENTS for the TBCK4A Base Station Transceiver Tested in accordance with: FCC 47 CFR Parts 22, and 90-subpart R RSS-119 Issue 11 RSS-Gen Issue 4 Report Revision: 1 Issue Date: 18-May-2015 PREPARED BY: Garry Pringle _______________ Test Technician CHECKED & APPROVED BY: M. C. James _______________ Laboratory Technical Manager OATS FCC LISTING REGISTRATION: 837095 OATS IC LISTING REGISTRATION: SITE# 737A-1 All tests reported herein have been performed in accordance with the laboratory's scope of accreditation. This document must not be reproduced except in full, without the written permission of the Compliance Laboratory Manager TELTEST Laboratories (A Division of Tait Communications) Telephone: 64 3 358 3399 PO Box 1645, 558 Wairakei Road, Christchurch, New Zealand. FAX: 64 3 359 4632 TELTEST Laboratories Tait Ltd Report Number 3646 FCC ID: CASTBCK4A Page 2 of 74 Report Revision: 1 IC : 737A-TBCK4A Issue Date: 18-May-2015 TABLE OF CONTENTS REVISION .................................................................................................................. 3 INTRODUCTION ........................................................................................................ 4 STATEMENT OF COMPLIANCE ............................................................................... 6 MODULATION TYPES, NECESSARY BANDWIDTH & EMISSION DESIGNATORS 7 TEST RESULTS ......................................................................................................... 9 TRANSMITTER OUTPUT POWER (CONDUCTED) .............................................. 9 TRANSMITTER AUDIO FREQUENCY RESPONSE - PRE-EMPHASIS .............. 11 TRANSMITTER MODULATION LIMITING ........................................................... 15 TRANSMITTER OCCUPIED BANDWIDTH AND SPECTRUM MASKS ............... 22 ADJACENT CHANNEL POWER .......................................................................... 41 TRANSMITTER SPURIOUS EMISSIONS (CONDUCTED) .................................. 48 TRANSMITTER SPURIOUS EMISSIONS (RADIATED) ....................................... 63 TRANSMITTER FREQUENCY STABILITY - TEMPERATURE ............................ 68 TRANSMITTER FREQUENCY STABILITY - VOLTAGE ...................................... 70 RECEIVER SPURIOUS EMISSIONS (CONDUCTED) ......................................... 71 TEST EQUIPMENT LIST.......................................................................................... 73 ANNEX A – TEST SETUP DETAILS ........................................................................ 74 TELTEST Laboratories Tait Ltd Report Number 3646 FCC ID: CASTBCK4A Page 3 of 74 Report Revision: 1 IC : 737A-TBCK4A Issue Date: 18-May-2015 REVISION Date Revision Comments 18-May-2015 1 Initial test report TELTEST Laboratories Tait Ltd Report Number 3646 FCC ID: CASTBCK4A Page 4 of 74 Report Revision: 1 IC : 737A-TBCK4A Issue Date: 18-May-2015 INTRODUCTION Type approval testing of the TBCK4A, 50 Watt, Base Station transceiver, in order to demonstrate compliance with FCC 47 Parts 22, & 90-subpart R, and RSS-119 Issue 11 & RSS-Gen Issue 4. This radio supports Analogue, APCO P25 phase-1 and APCO P25 phase-2 modulations. REPORT PREPARED FOR Tait Communications PO Box 1645 558 Wairakei Road Christchurch New Zealand DESCRIPTION OF SAMPLE Manufacturer Tait Limited Equipment: Base Station Transceiver Type: TBCK4A Sales Package Code TB9415-K4H0-K4H0-A1BA-10 Frequency range 762 Æ 870 MHz Transmit Power 50W HARDWARE & SOFTWARE – Digital Modulation Testing Quantity: 1of each Description Product Code Serial Number Firmware Version Hardware Version Reciter T01-01103-NAAA 18209183 p25-2.00.00.0005 00.00 Power Amplifier T01-01121-NAAA 18209414 1.07.00.0002 0006 PMU TBA30A0-0100 18208873 0316 01.00 Front Panel T01-01110-BAAA 18210060 1.07.00.0002 00.04 HARDWARE & SOFTWARE – Analogue Modulation Testing Quantity: 1of each Description Product Code Serial Number Firmware Version Hardware Version Reciter T01-01103-NAAA 18209183 p25-trunk.20150508T172430 00.00 Power Amplifier T01-01121-NAAA 18209414 0.01.00.trunk.360976.20140918 T113436 0006 PMU TBA30A0-0100 18208873 0316 01.00 Front Panel T01-01110-BAAA 18210060 0.01.00.trunk.375640.20150225 T133901 00.04 Modulation Channel Spacing Speech Channels Symbol Rate (symbols/sec) Data Rate (bps) Analogue FM 12.5 kHz 1 ~ ~ APCO P25 Phase 1 C4FM 12.5 kHz 1 4800 9600 LSM 12.5 kHz 1 4800 9600 APCO P25 Phase 2 H-DQPSK 12.5 kHz 2 6000 12000 TELTEST Laboratories Tait Ltd Report Number 3646 FCC ID: CASTBCK4A Page 5 of 74 Report Revision: 1 IC : 737A-TBCK4A Issue Date: 18-May-2015 TEST CONDITIONS All testing was perfor…

Text truncated - open the document above for the full version.