CB2-BLUE15M-TCUAutomotive Telematics Module with Handsfree Bluetooth

CB2 -BLUE15M-TCU Owner’s Manual Draft Johnson Controls, Inc. Automotive Experience 915 East 32 nd Street Holland, MI 49423 CB2-BLUE15M-TCU Owner’s Manual Draft Page 2 of 10 1 System Diagram The following diagram shows a high-level overview of how the user will be able to connect through the TCU to receive TCU services from the telematics service provider as well as the OEM servers. Figure 1: TCU Context Diagram CB2-BLUE15M-TCU Owner’s Manual Draft Page 3 of 10 2 Embedded Phone (CDMA) Features 2.1 Automatic Crash Notification (ACN) The ACN feature is used to establish a voice call with the Telematics Service Provider (TSP) call center in the event of a collision. A message is sent to the TSP with the location and vehicle status while an LED is blinked, textual indicators are displayed, and a prompt is played to the passengers notifying them of a pending voice call with the TSP. The TSP call center representative subsequently places an incoming voice call to the TCU and it is automatically answered. 2.2 Emergency Call (E-Call) The E-Call feature establishes a voice call with the TSP when user presses the Emergency button. An SMS is sent to the TSP call center with the location and vehicle status while a visual indicator is blinked, textual indicators are displayed, and a prompt is played notifying a pending voice call with the TSP. A TSP call center representative then places an incoming voice call to the TCU where it is automatically answered. 2.3 Roadside Assistance (R-Call) The R-Call feature establishes a voice call with the TSP when the user desires Roadside Assistance. When the NAVI sends an Establish Roadside Assistance (RA) message, the TCU sends an SMS to the TSP call center requesting an R-Call session. When the TSP call center responds with a voice call to the TCU, the TCU automatically answers the R-Call. 2.4 Information Call (I-Call) I-Call feature establishes a voice call with the TSP's IVR system when the user presses the Information (I-Call) button. A message is sent to the TSP requesting an I-Call session, while a visual indicator is blinked, textual indicators are displayed, and a prompt is played notifying of a pending voice call with the TSP. The TSP calls the TCU and it is automatically answered. 2.5 Security and Alerts The Security and Alerts feature notifies the user when specific events occur. Once an event is triggered, the TCU sends a report via SMS to the TSP. 2.6 Stolen Vehicle Tracking (SVT) The Stolen Vehicle Tracking feature tracks vehicle position. While SVT is active, the TCU sends periodic location updates to the TSP call center. 2.7 Remote Vehicle Functions Remote Vehicle Function feature is controlled by the TSP to remotely operate the electromechanical door locks in the vehicle and to view vehicle status. The feature supports unlocking the driver door, locking all doors, and sending vehicle indicators that could be viewed when in the vehicle. When the TCU receives a Remote Vehicle Function request via SMS from the TSP, it will perform the function requested and send the confirmation back to the TSP. CB2-BLUE15M-TCU Owner’s Manual Draft Page 4 of 10 2.8 Point of Interest (POI) Download The POI Download feature allows the user to request a destination download to their vehicle. Downloads can be initiated via the TSP operator or a website that offers a destination download option. TCU receives a message requesting POI information. The TCU will then import the destination information and report back to the TSP. 3 Handsfree Telephone (Bluetooth) Features 3.1 Product Description The TCU provides hands-free calling in the vehicle via the short-range wireless radio frequency communications protocol known as Bluetooth. Integrated into the vehicle audio systems and active on the data bus, the TCU provides the primary human interface functions to both telephone and installed audio systems when operating in the hands-free mode. The TCU includes the speech recognition engine and defined voice tree enabling the voice commanded operation of the system. Primary Hands- Free Telephone commands may also be initiated via switches provided on the steering wheel and Point of Interest selection screens via the Navi touch screen display. The transfer of stored cellular phone book entries to the TCU (Phone Book Access Push) and the transfer of the complete cellular phone book to the navigation unit upon request (Phone Book Access Pull) are accomplished via the Hands Free Link/Navi Communications. 3.2 Connection Management Connection Management refers to all the processes related to managing a mobile device (phone or audio player) including pairing device(s), deleting device(s), and managing connections to paired Bluetooth device(s). 3.2.1 Pairing The TCU supports two methods to pair a device. The first method, Legacy, requires the user to enter a pre-defined 4-digit pairing code. The second method enables a user to pair a device without entering a pairing code. This method is called “Secure Simple Pairing”. There are some phones that require a 4- digit pairing code before they will begin communicating with the TCU to initiate pairing. As a result the TCU will provide pairing code instructions to the user in some cases when it may not be necessary. This will be described in detail under Passive Pairing, below. The TCU system can add Mobile Devices, one device at a time. Prior to pairing a new device, the TCU will disconnect from all currently connected devices to prevent unwanted interruptions during the pairing process. If the device supports BT version 2.1 or greater, the TCU will determine the security level available on the Mobile Device. If the device supports BT version 2.0 or earlier, the TCU will initiate the Legacy Pairing method. 4-Digit Code Pairing (Legacy Pairing): When adding a device to the TCU, the user may enter a pairing code on the mobile device (only if the device does not support Bluetooth 2.1). The TCU has a pre-defined pairing code so that the user does no…

Text truncated - open the document above for the full version.

Date: Mar. 10, 2014 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Ref: Confidentiality request for FCC ID: CB2-BLUE15M-TCU FCC ID: Title/model: CB2-BLUE15M-TCU CB2-BLUE15M-TCU To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, Johnson Controls Interiors L.L.C. hereby request permanent confidentiality to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose: - Block diagram - Schematics - Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to Johnson Controls Interiors L.L.C. and provide unjustified benefits to our competitors. Johnson Controls Interiors L.L.C. understand that pursuant to §0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Signed on behalf of Johnson Controls Interiors L.L.C. in Holland on Mar. 10, 2014 By: __p.a.______________________ Scott Keller (Signature) (Print name) Title: Senior Product Engineer On behalf of: Johnson Controls Interiors L.L.C. (Company Name) Telephone: +1 616 394 1568 e-mail: [email protected]

Date: Mar. 10, 2014 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL REF: Short-term confidentiality request for FCC ID: CB2-BLUE15M-TCU FCC ID: Title/model: CB2-BLUE15M-TCU CB2-BLUE15M-TCU To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, Johnson Controls Interiors L.L.C. hereby request short- term confidentiality to avoid premature release of sensitive information prior to marketing or release of the product to the public. For the product stated above, we request that the following information be temporarily withheld from public disclose for an initial period of 180 days: - External photographs - Internal photographs - Users guide - Test setup photographs It is understood that no extensions of the short-term confidentiality may be requested. Signed on behalf of Johnson Controls Interiors L.L.C. in Holland on Mar. 10, 2014 By: __p.a.______________________ Scott Keller (Signature) (Print name) Title: Senior Product Engineer On behalf of: Johnson Controls Interiors L.L.C. (Company Name) Telephone: +1 616 394 1568 e-mail: [email protected]

Exterior – Top View Exterior – Bottom View Exterior – Connector / Side View

Confidential Product Label Product Label Placement on Module Model #/FCC ID: CB2-BLUE15M-TCU Contains FCC ID: N7NAR5550 IC : 279B-BLUE15M-TCU Contains IC: 2417C-AR5550 Contient IC: 2417C-AR5550 Model #/FCC ID: CB2-BLUE15M-TCU Contains FCC ID: N7NAR5550 IC: 279B-BLUE15M-TCU Co ntains IC: 2417C-AR5550 Contient IC: 2417C-AR5550

Assembly View PCBA Top View PCBA Bottom View PCBA Bottom View – EMC Shield Removed

Date: Mar. 10, 2014 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL RF exposure analysis for the equipment CB2-BLUE15M-TCU (FCC ID: CB2-BLUE15M-TCU; IC: 279B-BLUE15M-TCU) The output power of the device is extremely low and far below: 1. The FCC SAR test exclusion threshold as stated in KDB 447498 D01 General RF Exposure Guidance v05r02 Clause 4.3.1-1): [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [ √f(GHz)] ≤ 3.0 Therefore, the device meets the FCC SAR exemption requirements. 2. The IC SAR test exclusion threshold as stated in RSS-102 Issue 4 Clause 2.5.1: above 2.2 GHz and up to 3 GHz inclusively, and with output power (i.e. the higher of the conducted or radiated (e.i.r.p.) source-based, time-averaged output power) that is less than or equal to 20 mW for general public use and 100 mW for controlled use; Max. conducted: 0,668 mW ≤ 20 mW Max eirp: 0,841 mW ≤ 20 mW Therefore, the device meets the IC SAR exemption requirements. For that reason the equipment is categorically excluded from routine environmental evaluation for RF exposure and it is deemed to comply with FCC and IC limits for exposure to electromagnetic fields. This product also integrates an AR5550 CDMA modem (FCC ID: N7NAR5550, IC: 2417C-AR5550. The AR5550 modem is granted with a modular approval for mobile applications. Integration has been done meeting the following conditions: 1. At least 20cm separation distance between the antenna and any person body is maintained at all times. 2. To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile only exposure condition does not exceed 4.25dBi for CDMA 800 band and 6.1dBi for CDMA PCS band. 3. The AR5550 antenna is not co-located with any other antennas. Modulation Frequency (GHz) Maximum output power (dBm) Maximum output power (mW) Evaluation distance (mm) Power (mW)/Distance (mm) * √f(GHz) Threshold COMPLIANCE: [Power (mW)/Distance (mm) * √f(GHz)] ≤ Threshold 2,402-2,800,52550,1633,000COMPLIANT 2,441-1,750,66850,2093,000COMPLIANT 2,480-1,780,66450,2093,000COMPLIANT 2,402-3,260,47250,1463,000COMPLIANT 2,441-2,180,60550,1893,000COMPLIANT 2,480-2,230,59850,1883,000COMPLIANT 2,402-3,040,49750,1543,000COMPLIANT 2,441-2,150,61050,1903,000COMPLIANT 2,480-2,220,60050,1893,000COMPLIANT GFSK Π/4-DQPSK 8-DPSK Product configuration is as follows: Signed on behalf of Johnson Controls Interiors L.L.C. in Holland on Mar. 10, 2014 By: __p.a.______________________ Scott Keller Title: Senior Product Engineer On behalf of: Johnson Controls Interiors L.L.C. Telephone: +1 616 394 1568 e-mail: [email protected] Model: CB2-BLUE15M-TCU FCC ID: CB2-BLUE15M-TCU IC: 279B-BLUE15M-TCU Sierra Wireless CDMA module Model: AR5550 FCC ID: N7NAR5550 IC ID: 2417C-AR5550 Embedded Bluetooth antenna Antenna to person distance < 20 cm Antenna to person distance > 20 cm Antenna to antenna distance > 20 External CDMA antenna

Report Nº(NIE): 40296RRF.001 Page 1 of 81 2014-03-10 FCC LISTED, REGISTRATION NUMBER: 720267 IC LISTED REGISTRATION NUMBER IC 4621A-1 AT4 wireless, S.A. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 29590 Campanillas/ Málaga/ España Tel. 952 61 91 00 - Fax 952 61 91 13 MÁLAGA, C.I.F. A29 507 456 Registro Mercantil de Málaga,Tomo 1169, Libro 82, Folio 133, Hoja MA3729 TEST REPORT REFERENCE STANDARD: USA FCC Part 15.247, 15.209 CANADA RSS-210, RSS-Gen Radio Frequency Devices. Operation within the bands 902 - 928 MHz, 2400 -2483.5 MHz, and 5725 - 5850 MHz. Licence-Exempt Radio Apparatus (All Frequency Bands): Category I Equipment. General Requirements and Information for the Certification of Radio Apparatus. NIE ........................................................ : 40296RRF.001 Approved by (name / position & signature) ............... : A. Llamas / RF Lab. Manager .......................................................... Elaboration date .................................... : 2014-03-10 Identification of item tested ................ : Automotive Telematics Module with Handsfree Bluetooth Brand name ........................................... : Johnson Controls Interiors Model and/or type reference ................. : CB2-BLUE15M-TCU Serial number ........................................ : TAM2555455002H05, TAM2555455002V05 Other identification of the product ........ : Hw version: 5 Sw version: 01.01.012 FCC ID: CB2-BLUE15M-TCU IC: 279B-BLUE15M-TCU Features ................................................. : Bluetooth Device Johnson Controls Interiors CB2-BLUE15M-TCU is a Bluetooth 2.1+EDR handsfree, with CDMA phone module (FCC ID: N7NAR5550 IC ID:2417C-AR5550) embedded, to be integrated in cars which allows to place and receive phone calls using voice commands, without handling the cell phone Description ............................................ : Automotive Telematics Module with Handsfree Bluetooth Applicant ............................................. : Johnson Controls INC. Address .................................................. : 915 East 32nd Street, Holland, MI 49423 USA CIF/NIF/Passport ................................... : --- Contact person: Scott Keller Telephone / Fax ..................................... : +1 616-394-1568 e-mail: ................................................... : [email protected] Test samples supplier ......................... : Same as applicant Manufacturer ...................................... : Same as applicant Report Nº(NIE): 40296RRF.001 Page 2 of 81 2014-03-10 Test method requested ........................: See Standard Standard ................................................: USA FCC Part 15.247 10-01-12 Edition: Operation within the bands 902 - 928 MHz, 2400 -2483.5 MHz, and 5725 - 5850 MHz. USA FCC Part 15.209 10-01-12 Edition: Radiated emission limits; general requirements. CANADA RSS-210 Issue 8 (December 2010). CANADA RSS-Gen Issue 3 (December 2010). FCC part 15.247 and Filing and Measurement Guidelines for Frequency Hopping Spread Spectrum System DA 00-705 Released March 30, 2000. ANSI C63.10-2009: American National Standard for Testing Unlicensed Wireless Devices. Test procedure .......................................: PERF010 Non-standardized test method ...............: N/A Used instrumentation .............................: Conducted Measurements Last Cal. date Cal. due date 1. Spectrum analyser Agilent PSA E4440A 2012/02 2014/02 2. DC power supply R&S NGPE 40/40 2011/11 2014/11 Radiated Measurements Last Cal. date Cal. due date 1. Semianechoic Absorber Lined Chamber IR 11. BS N.A. N.A. 2. Control Chamber IR 12.BC N.A. N.A. 3. Hybrid Bilog antenna Sunol Sciences Corporation JB6 2011/05 2014/05 4. Antenna mast EM 1072 NMT N.A. N.A. 5. Rotating table EM 1084-4. ON N.A. N.A. 6. Double-ridge Guide Horn antenna 1-18 GHz HP 11966E 2011/05 2014/05 7. Double-ridge Guide Horn antenna 18- 40 GHz Agilent 119665J 2011/09 2014/09 8. EMI Test Receiver R&S ESIB26 2013/05 2015/05 9. RF pre-amplifier Miteq JS4-12002600- 30-5A. 2012/07 2014/07 10. Multi Device Controller EMCO 2090 N.A. N.A. 11. Spectrum analyser R&S FSW50 2013/10 2015/10 12. RF pre-amplifier Miteq AFS5- 04001300-15-10P-6. 2012/07 2014/07 13. RF pre-amplifier Schaffner CPA 9231. 2013/06 2015/06 14. Spectrum analyser Agilent PSA E4440A 2012/02 2014/02 Report template No. .............................: FDT08_14 IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of AT4 wireless, S.A. Report Nº(NIE): 40296RRF.001 Page 3 of 81 2014-03-10 INDEX Competences and guarantees ................................................................................................................ 4 General conditions ................................................................................................................................ 4 Uncertainty ............................................................................................................................................ 4 Usage of samples................................................................................................................................... 5 Testing period ....................................................................................................................................... 5 Environmental conditions ..................................................................................................................... 6 Summary ............................................................................................................................................... 7 Remarks and comments ........................................................................................................................ 7 Testing verdicts ................................................................................................................................…

Text truncated - open the document above for the full version.

Report Nº(NIE): 40296RRF.001 Page 2 of 7 2014-03-10 EQUIPMENT FOR RADIATED MEASUREMENTS

Report Nº(NIE): 40296RRF.001 Page 3 of 7 2014-03-10 EQUIPMENT FOR CONDUCTED MEASUREMENTS

Report Nº(NIE): 40296RRF.001 Page 4 of 7 2014-03-10 GENERAL SET-UP FOR RADIATED MEASUREMENTS

Report Nº(NIE): 40296RRF.001 Page 5 of 7 2014-03-10 TEST SET-UP FOR RADIATED MEASUREMENTS BELOW 1 GHz

Report Nº(NIE): 40296RRF.001 Page 6 of 7 2014-03-10 TEST SET-UP FOR RADIATED MEASUREMENTES ABOVE 1GHz

Report Nº(NIE): 40296RRF.001 Page 7 of 7 2014-03-10 TEST SET-UP FOR CONDUCTED MEASUREMENTES