CFS8DLLYNXRENremote keypad

PRELIMINARY /<1;56HULHV 6HFXULW\6\VWHPV  ,QVWDOODWLRQDQG6HWXS*XLGHIRU /<1;5/<1;5DQG/<1;5(1 AWAY OFF STAY AUX ® K5963 5/01 ® –3– Table of Contents SYSTEM FEATURES ....................................................................................................................... 4 MOUNTING THE CONTROL ......................................................................................................... 5 WIRING CONNECTIONS................................................................................................................ 6 AC POWER AND BACKUP BATTERY ......................................................................................... 9 INSTALLING WIRELESS ZONES................................................................................................ 11 MECHANICS OF PROGRAMMING ............................................................................................. 14 ZONE RESPONSE TYPE DEFINITIONS...................................................................................... 15 DATA FIELD DESCRIPTIONS ..................................................................................................... 17 *56 ENHANCED ZONE PROGRAMMING MODE ..................................................................... 24 *80 DEVICE PROGRAMMING MENU MODE ........................................................................... 29 *81 ZONE LIST MENU MODE ..................................................................................................... 32 *83 ENHANCED SEQUENTIAL MODE ...................................................................................... 33 *84 ASSIGN ZONE VOICE DESCRIPTORS ................................................................................ 35 *85 RECORD CUSTOM VOICE DESCRIPTORS ........................................................................ 37 REMOTE PROGRAMMING/CONTROL (DOWNLOADING) .................................................... 38 SYSTEM OPERATION .................................................................................................................. 39 TESTING THE SYSTEM................................................................................................................ 44 SYSTEM COMMUNICATION ...................................................................................................... 45 TROUBLESHOOTING GUIDE...................................................................................................... 47 REGULATORY AGENCY STATEMENTS .................................................................................. 49 SPECIFICATIONS .......................................................................................................................... 50 LYNXR/LYNXR24 PROGRAMMING DEFAULT TABLES ....................................................... 51 LYNXR-EN PROGRAMMING DEFAULT TABLES ................................................................... 52 INDEX ............................................................................................................................................. 55 LIMITATIONS OF THIS SYSTEM STATEMENT ....................................................................... 57 WARRANTY................................................................................................................................... 58 SUMMARY OF CONNECTIONS DIAGRAM .............................................................................. 59 –49– Regulatory Agency Statements UL NOTICE: This is a "Grade A" residential system. FCC ID: CFS8DLLYNXREN RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. TELEPHONE/MODEM INTERFACE Federal Communications Commission (FCC) Part 68 This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment is hearing-aid compatible. Industry Canada NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections thems…

Text truncated - open the document above for the full version.

Cover letter Federal Communications Commission, ADEMCO, Equipment Approval Services, 165 Eileen Way, PO Box 358315 Syosset, Pittsburgh, NY 11791 PA 15251-5315 5/9/01. SUBJECT: Application for certification of Ademco's transceiver type LYNX. FCC ID: CFS8DLLYNXREN Dear Sir, Please find enclosed a completed 731 form, a description of the transceiver, circuit schematics, label drawing, test report, photographs, and application fee for certification of Ademco's model LYNX transceiver under FCC Rules and Regulations Part 15, Subpart C. The receiver contained within the transceiver is a superhet. If you have any questions or require additional information, please contact the undersigned. Yours Sincerely, Ken Addy, Director of Radio Eng. LIST OF EXHIBITS CFS8DLLYNXREN 1) Description of the LYNX 2) Circuit description and schematic 3) Message Protocol, timing and duty cycle calculation 4) Photographs showing location of FCC ID label. 5) Report of measurements 6) Test equipment list 7) Installation instruction including FCC compliance statement and FCC user's warning

EXHIBIT 1-1 FCC I.D.: CFS8DLLYNXREN Functional Description. The LYNX fixed transceiver is part of Ademco’s wireless 5800 alarm system. It is used in conjunction with portable transmitters (e.g. 5804) or portable transceivers (e.g. 5804BD). This allows remote control of the alarm system and provides remote indication that a control instruction has been enacted. In addition control events and alarm events initiated at the Lynx keypad are also transmitted to wireless relay and wireless siren type devices. These messages are transmitted at 345Mhz +/-82kHz using on-off keyed AM modulation. The LYNX does not send a regular supervision or check-in message, it sends no other messages except alarm messages, control messages initiated at the Lynx keypad, and messages which are a confirmation of reception of manually initiated control messages which have been received from portable remote control transmitters.

EXHIBIT 2-1 Circuit Description. FCC ID: CFS8DLLYNXR The LYNX is constructed on a pair of PCBs interconnected via a ribbon cable. The main PCB contains the RF transmitter and receiver circuitry as well as all control, display, keypad and annunciation circuitry. The transmitter is a SAW resonator Colpitts oscillator, Q26, YL5, etc. The transmitter is on-off keyed (AM) modulated by a control signal from the microcontroller U18 which turns PA Q30 on or off via Q28/Q29, thus modulating the output signal. The RF output signal is connected to two PCB mounted antennas via FL1 & diodes CR32/CR33. The receiver is a superhet with a single intermediate frequency at 10.7MHz. Q31 etc. is the low noise amplifier which is connected to the PCB mounted antennas. Diodes CR32/CR33 under the control of a microcontroller are periodically switched to provide system antenna diversity. The IC U22 includes a balanced mixer, & phase locked L.O. (YL1 @ 10.446875 Mhz X 34 = 355.7 Mhz) which converts the incoming signal down from 345MHz to 10.7MHz. This IC also includes the required IF gain and detected output. FL3 is a ceramic IF filter. IC U19 performs video filtering and processing and provides a data signal.

EXHIBIT 5-1 CFS8DLLYNXREN Report of Measurements. Measurements were made at Ademco 's Measurement Facility at 160 Eileen Way , Syosset , NY 11791 , FCC Registration number : 90421. Measurements were made in accordance with the procedures and reporting requirements of ANSI C63.4-1992. The Test Set-Up (C63.4 section 10.1.3) is shown in the attached drawing. The sequence of testing (C63.4 section 10.1.7) for radiated emissions is as follows: A preliminary scan was conducted with the receiver antenna close to the EUT in order to identify the emission characteristics of the EUT (C63.4 section 8.3.1.1). The antenna and EUT were then placed at the proper separation with the EUT positioned on a non-conducting turntable. The EUT was rotated on the turntable to maximize the received signal strength, then the receiver antenna height was varied to further maximize the received reading. Thereafter, the device was again rotated to a peak output position and the antenna height was re-adjusted for maximum received signal. This procedure was re-iterated until there was no further increase in signal level. This procedure was performed with the EUT rotating in three orthogonal planes (C63.4 section 13.1.4.1) to generate a final maximum reading which is recorded on the radiated emissions result sheet. Similar measurements were made on the receiver to ensure compliance as an unintentional radiator. See Exhibit 6 for list of test equipment (C63.4 section 10.1.4). Note, Spectrum Analyzer resolution bandwidths set as follows; (Video Bandwidth set greater than RBW) - For occupied bandwidth measurements, RBW = 100kHz, (This is in accordance with the minimum RBW allowed by C63.4, which requires RBW greater than 5% of the FCC required occupied bandwidth spec of 0.25% of center frequency). - For radiated emissions below 1 GHz, the RBW = 100kHz. Detector function set to peak. - For radiated emissions above 1 GHz, the RBW = 1MHz. Detector function set to peak. OCCUPIED BANDWIDTH is shown on attached plot. RADIATED EMISSIONS are recorded on attached sheet.

Frequency (MHz) Antenna Polarity ( V-H ) Meter Reading (dB uV) Cable/Amp Factor ( dB ) Antenna Factor (dB/M) Converted Reading ( uV/M ) Duty Cycle ( % ) Corrected Reading ( uV/M ) Limit @ 3 Meter ( uV/M ) 30 H 15.26 729 345 V 76.9 1.5 15.1 47,315.1 15.26 7,220 7,290 690 V 39.83 2.1 20.6 1,338.1 15.26 204.2 729 1035 H 33.33 2.6 24.0 992 15.26 151.4 500 1380 H 34.0 3.0 27.9 1,758.0 15.26 268.3 500 1725 V 33.0 3.4 30.0 2,089.3 15.26 318.8 729 2070 H 34.0 3.7 28.0 1,927.5 15.26 294.1 729 2415 H 28.0 4.0 28.8 1,096.5 15.26 167.3 729 2760 H 23.0 4.3 30.0 732.8 15.26 111.8 729 3105 H 27.67 4.5 30.7 1,391.6 15.26 212.4 729 3450 H 27.17 4.8 31.1 1,424.0 15.26 217.3 729 4000 H 15.26 729 EXHIBIT 5-3 MAY, 04, 2001 GREG BARBATO KEN ADDY DATE:____________________ TESTED BY:_________________________APPROVED BY:________________________ ADEMCO LYNX (TRANSMITTER) TEST SAMPLE (model): _______________________________________________________________________________ TEST METHOD: ANSI C63.4-1992 TEST SPECIFICATION: FCC PART 15, SUBPART C. NOTES: 1) Fo= 345 MHZ 2) DETECTOR = PEAK. 3) FREQUENCY RANGE SCANNED TO 4 GHz. (METER READING +CABLE /AMP FACTOR +ANTENNA FACTOR) 20 4) CONVERTED READING = 10 5) CORRECTED READING = CONVERTED READING X DUTY CYCLE 6) SIX HIGHEST EMISSIONS RECORDED. ALARM DEVICE MANUFACTURING COMPANY 165 EILEEN WAY CFS8DLLYNXREN SYOSSET, NY 11791 FCC ID#____________________

EXHIBIT 6 CFS8DLLYNXREN Test Equipment list 1. Antenna: RGA-60 S/N: 6127 Cal. on: 10/19/00 Cal. due: 10/19/01 2. Antenna: Log Periodic S/N:365 Cal. on: 07/28/00 Cal. due: 07/28/01 3. Spectrum Analyzer R & S S/N:1065.6000.20 Cal. on: 06/29/00 Cal. due: 06/29/01