CGD-SF4134 kHz Inductive Tag Reader

VC4 T/R SF4 ISO FDX/HDX CONTENTS page 1 General 1 2 Operation 1 3 Installation 2 4 Set Address 4 5 Adjust antenna 5 6 Adjust Neutrodynisation 7 6 Display values 9 7 Internal test menu 10 8 Trouble shooting 11 Fig. 1 Overview SF4 cable connections (Feed model) 12 Fig. 2 Overview SF4 cable connections (Walkthrough model) 13 Fig. 3 Overview SF4 cable connections with walk-by ID 14 Fig. 4 Overview SF4 + Booster cable connections with walk-by ID 15 Fig. 5 Display menu 16 10-2005 Nedap Agri bv SF4.eng version 0.2 Single Feeder 4 - 1 - 10/2005 Version 0.2 1 General The Transmitter/Receiver Single Feeder 4 (SF4) is a re-design of the SF2 and can be used for identifying of ISO FDX en HDX responders. SF4 compared to SF2 The SF4 print is based on the SF2. Cable connections are the same as with a SF2. When using HDX and ISO operation a synchronisation cable must be installed. Most important change is that FDX and HDX responder types can be identified according to the full ISO standard 11784 and 11785. EPROM on the T/R SF4 Eproms that are suitable for a SF2 can be used on a SF4. Important is that ISO identification in the software is included. If ISO is possible, the ri menu option is available at responder select. Caution because of pulsating transmitter (HDX) Although everything is done to minimize, there is a possibility that the magnetic radiation of the antenna, connected to this reader, influences the behavior of a pacemaker. Users of a pacemaker are advised to avoid close contact between their pacemaker and the antenna of the SF4 In Germany and Denmark the maximum allowed level is 42 dBμA /m. at 134.2 kHz. For most other countries in Europe this maximum level is 65 dBμA/m. 2 Operation See manual as used for a SF2 Single Feeder 4 - 2 - 10/2005 Version 0.2 3 Installation The Nedap guarantee-regulations are only valid when the SF4 is installed as indicated in this manual. The following is important : Technical specifications Single Feeder 4 Input voltage 22-42 VDC Max. current per output (motors) 3A DC Operating temperatures (environment) -10ºC / +45ºC Transport / storage temperatures -25ºC / +70ºC Humidity (rh) 45ºC / 93% Enclosure protection class (cover and cables installed correctly !) IP65 Always use a NEDAP SMPS power supply Never change a prom when the power to the T/R is still switched on Install data cables at a safe distance from (high) powered cables Wiring the SF4 Figure 1 shows an overview of the T/R SF4 cable-connection. Cable specifications Cable length at power supply 27V: IB Æ SF4 Max. 40m at wire-ø = 0.8 mm SF4 Æ motor Standard cable of the motor SF4 Æ antenna Standard cable of the antenna Synchronisation (HDX and ISO operation) Twisted pair minimum 2x0.24mm 2 shielded. Total max. 500m IMPORTANT: All cables used for data communication must have shielding! Hardware motor safeguard When the micro processor has no control over the T/R anymore and a motor is running uncontrolled and keeps turning continuously, a hardware circuit on the T/R will stop the motor by means of a relay (25 seconds (+/- 5 sec)). This motor safeguard can only be reset by switching off the power from the T/R for a few seconds. Software motor safeguard This software function monitors the motor current. If a motor current is detected which is too high (I motor > 900 mA) for a certain time, the T/R program will try to stop the motor. If the motor can not be stopped, the T/R program will shut off the power supply on all outputs. Single Feeder 4 - 3 - 10/2005 Version 0.2 Synchronisation for HDX A synchronisation cable is necessary for HDX to synchronise T/Rs that can influence each other. For FDX only (jumper set to FDX only) synchronisation is not necessary. The connector at the right hand side (SYNC) contains a synchronisation signal for HDX (SYNC). SYNC has to be connected to all other HDX Single Feeders in the neighbourhood. There is no + or -. Maximum number is 16 that can be connected together for synchronization. If a cable is used with shielding, the shielding must not be connected at the bottom plate of the PCB but left as not connected. Jumper for FDX / HDX or FDX only If set to FDX / HDX the red led is blinking during transmitting the synchronisation signal. When set to FDX only, the red led remains off. LEDs The tree leds are used for tuning the antenna. The two leds are for idenfication (green) and synchronisation (red). Shielding, grounding In order to protect the SF4 for over-voltages / induction, the cable from the interface bridge to the SF4 must be a shielded cable. Connections: interface bridge connected to "-"terminal Transmitter / Receiver connected to ground-terminal N.B. All T/R electronics must be isolated. Also the T/R bottom plate has to be isolated from the T/R ground-terminal. Warnings • Due to guarantee-regulations, the entire T/R PCB (incl. metal plate) must be changed. SYNC SYNC SYNC Single Feeder 4 - 4 - 10/2005 Version 0.2 4 Set Address For communication the Transmitter / Receiver needs an address. Then the computer knows where to send the information to. At the transmitter / receiver with help of the display and the push button the stations address is configured. The two segment display and the yellow push-button must also be used for several adjustments of the Transmitter / receiver. A number of different codes will appear on the display when the push-button is pushed, these codes represent the so-called menus. Each menu on its turn is divided into a number of functions. By varying the pushing time of the push-button, you will get access to the different menus and/or functions. The first time you switch on the power of the T/R, the display will show "0-". The Transmitter / Receiver asks now for the first address. When an address is entered the display will blank out and the transmitter / receiver returns to the normal status. The address setting concerns the following menus and procedures (see figure 3): • Address menu - Set Address - display Address N.B. Remember that the used p…

Text truncated - open the document above for the full version.

;' r---1I-==I. IF==J" 5ecurity5ystems ManagementInfD5ystems ElectiDn5ystems ~ Electronics.MetalandPlastic May1, 2006 Towhomit mayconcern, Thisletterconfirmstheagreementthat TNOElectronicProducts& Services(EPS)B.V. Smidshornerweg18 9822TLNiekerk TheNetherlands is authorizedasanagentfor: NV.NederlandscheApparatenfabriek"NEDAP" Parallelweg2 7141DCGroenlo TheNetherlands andis authorizedtosignapplicationformsandactonbehalfof JAM.Hulshof(N.V.Nederlandsche Apparatenfabriek"NEDAP");andis authorizedtoreceiveandexchange databetweenJAM.Hulshof(N.V. NederlandscheApparatenfabriek"NEDAPjandEuropeanornon-Europeannationalauthoritiesregarding the-certificationof-and/or-arrangingtypeapprovalsfor-product(s)ofN.V.Nederlandsche Apparatenfabriek"NEDAP". ThisauthorizationwillexpireonMay1, 2007oruponearlierwrittennoticefromN.V.Nederlandsche Apparatenfabriek"NEDAP". .. "Hulshof ApprobationManagement Phone:+31544471162 Fax:+31544463475 E-mail:[email protected] E c u Co ~ 'C ~ C N.V.Nederlandsche T+31[OJ54447]]I] ~ ~ ~ Apparatenfabriek"Nedap"F+31[oJ544453475 [email protected] NL-7141DC5roenloHandelsregisteroBo]3B36 P.O.Box5 NL-7]4oAA6roenlo ABN-AMRo59.16.32.330IBANNLB3ABNA059153233oBICABNANL2ABTWNLo064562B5Boi

TNO Electronic Products & Services (EPS) B.V. Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno.nl T +31 594 505005 F +31 594 504804 E [email protected] Subject Request for confidentiality Date May 9, 2006 Our reference 06K0249 Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands FCC TCB Dear Sir or Madam: Pursuant to section 0.457 and 0.459 of the FCC rules we herewith request the following exhibits, related to the application for FCC ID: CGD-SF4, to be withheld from public inspection and to be kept confidential. The contents of these exhibits may not be disclosed to other parties than NEDAP N.V. (the grantee) and TNO Electronic Products & Services (EPS) B.V.: 1. Bill of materials 2. Circuit diagram 3. Block diagram 4. theory of operation The reason for this request for confidentiality is that the information contained in the exhibits as listed above has been classified as company confidential. Disclosure of any portion of this information to other parties would cause substantial competitive harm. None of the referred information has been disclosed to the general public. Best regards, TNO Electronic Products & Services (EPS) B.V. J. Schuurmans, B.Sc.E.E. Senior Engineer Telecom/EMC

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Project number: 06020907.p01 Page 1 of 4 47 CFR 15 EXTERNAL PHOTOGRAPHS OF AN INDUCTUVE PROXIMITY TAG READER OPERATING ON 134 KHZ, BRAND NEDAP, MODEL SF-4 FCC listed Industry Canada : : 90828 IC3501 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p01 Page 2 of 4 Description of test item Test item : 134 kHz Inductive Tag Reader Manufacturer : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Brand : Nedap Model : SF-4 Serial number(s) : -- Revision : -- Receipt date : -- Applicant information Applicant's representative : Mr. J.A.M. Hulshof Company : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 This report is in conformity with NEN-EN-ISO/IEC 17025: 2000. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p01 Page 3 of 4 Table of contents 1 External Photographs .............................................................................................................................................................4 1.1 Main unit (front view). ...................................................................................................................................................4 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p01 Page 4 of 4 1 External Photographs 1.1 Main unit (front view).

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Project number: 06020907.p02 Page 1 of 10 47 CFR 15 INTERNAL PHOTOGRAPHS OF AN INDUCTUVE PROXIMITY TAG READER OPERATING ON 134 KHZ, BRAND NEDAP, MODEL SF-4 FCC listed Industry Canada : : 90828 IC3501 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 2 of 10 Description of test item Test item : 134 kHz Inductive Tag Reader Manufacturer : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Brand : Nedap Model : SF-4 Serial number(s) : -- Revision : -- Receipt date : -- Applicant information Applicant's representative : Mr. J.A.M. Hulshof Company : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 This report is in conformity with NEN-EN-ISO/IEC 17025: 2000. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 3 of 10 Table of contents 1 Internal Photographs...............................................................................................................................................................4 1.1 Main unit (front view). ...................................................................................................................................................4 1.2 Internal pictures. .............................................................................................................................................................5 1.2.1 Open view...............................................................................................................................................................5 1.2.2 Openview (continued) ............................................................................................................................................6 1.2.3 PCB top view..........................................................................................................................................................7 1.2.4 sub PCB 1 side view...............................................................................................................................................8 1.2.5 sub PCB 1 side rear view........................................................................................................................................9 1.2.6 Main PCB copper side view .................................................................................................................................10 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 4 of 10 1 Internal Photographs 1.1 Main unit (front view). Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 5 of 10 1.2 Internal pictures. 1.2.1 Open view. Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 6 of 10 1.2.2 Openview (continued) Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 7 of 10 1.2.3 PCB top view Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 8 of 10 1.2.4 sub PCB 1 side view Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 9 of 10 1.2.5 sub PCB 1 side rear view Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî NEDAP SF-4 Project number: 06020907.p02 Page 10 of 10 1.2.6 Main PCB copper side view

Testing and certification of, consultancy and research concerning, electronic and electric appliances, systems, installations and telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Project number: 06020907.r02 Page 1 of 21 TEST REPORT CONCERNING THE COMPLIANCE OF AN INDUCTIVE PROXIMITY TAG READER OPERATING ON 134 KHZ, BRAND NEDAP, MODEL SF-4 WITH 47 CFR PART 15 (2006-02-01). FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî Nedap SF-4 CGD-SF4 Project number 06020907.r02 Page 2 of 21 MEASUREMENT/TECHNICAL REPORT Nedap N.V. Model : SF-4 FCC ID: CGD-SF4 May 9, 2006 This report concerns: Original grant/certification Class 2 change Verification Equipment type: Inductive proximity tag reader Deferred grant requested per 47 CFR 0.457(d)(1)(ii) ? Yes No n.a. Report prepared by: Name : J. Schuurmans, B.Sc.E.E. Company name : TNO Electronic Products & Services (EPS) B.V. Address : Smidshornerweg 18 Postal code/city : 9822 TL Niekerk Mailing address : P.O. Box 15 Postal code/city : 9822 ZG Niekerk Country : The Netherlands Telephone number : + 31 594 505 005 Telefax number : + 31 594 504 804 E-mail : [email protected] The data taken for this test and report herein was done in accordance with 47 CFR Part 15 and the measurement procedures of ANSI C63.4-2003. TNO Electronic Products & Services (EPS) B.V. at Niekerk, The Netherlands, certifies that the data is accurate and contains a true representation of the emission profile of the Equipment Under Test (EUT) on the date of the test as noted in the test report. I have reviewed the test report and find it to be an accurate description of the test(s) performed and the EUT so tested. Date: May 9, 2006 Signature: P.A.J.M. Robben, B.Sc.E.E. TNO Electronic Products & Services (EPS) B.V. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî Nedap SF-4 CGD-SF4 Project number 06020907.r02 Page 3 of 21 Description of test item Test item : 134 kHz Inductive proximity tag reader Manufacturer : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Brand : Nedap Model : SF-4 Serial number(s) : -- Revision : -- Receipt date : -- Applicant information Applicant's representative : Mr. J.A.M. Hulshof Company : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 Test(s) performed Location : Niekerk Test(s) started : March 13, 2006 Test(s) completed : April 24, 2006 Purpose of test(s) : Equipment Authorisation (Certification). Test specification(s) : 47 CFR Part 15 (2006-02-01) Test engineers : J. Schuurmans, B.Sc.E.E. P. de Beer Report written by : J. Schuurmans, B.Sc.E.E. Report date : May 9, 2006 This report is in conformity with NEN-EN-ISO/IEC 17025: 2000. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 47 CFR Part 15 (2006-02-01) Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek ìNEDAPî Nedap SF-4 CGD-SF4 Project number 06020907.r02 Page 4 of 21 Table of contents 1 General information. ..............................................................................................................................................................5 1.1 Product description.........................................................................................................................................................5 1.1.1 Introduction. ...........................................................................................................................................................5 1.2 Related submittal(s) and/or Grant(s). .............................................................................................................................5 1.3 Tested system details......................................................................................................................................................5 1.3.1 Description of input and output ports. ....................................................................................................................6 1.4 Test methodology. ..........................................................................................................................................................6 1.5 Test facility.....................................................................................................................................................................7 1.6 Product labeling..............................................................................................................................................................7 2 System test configuration. ......................................................................................................................................................8 2.1 Justification. ...................................................................................................................................................................8 2.2 EUT mode of operation. .................................................................................................................................................8 2.3 Special accessories. ......................................................................…

Text truncated - open the document above for the full version.

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 06020907.p03 Page 1 of 9 47 CFR PART 15 TEST SETUP PHOTOGRAPHS OF AN INDUCTUVE PROXIMITY TAG READER OPERATING ON 134 KHZ, BRAND NEDAP, MODEL SF-4 FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 2 of 9 Description of test item Test item : 134 kHz Inductive Tag Reader Manufacturer : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Brand : Nedap Model : SF-4 Serial number(s) : -- Revision : -- Receipt date : -- Applicant information Applicant's representative : Mr. J.A.M. Hulshof Company : N.V. Nederlandsche Apparatenfabriek ìNEDAPî Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 This report is in conformity with NEN-EN-ISO/IEC 17025: 2000. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 3 of 9 Table of contents 1 Test setup photographs of radiated emission measurements. .................................................................................................4 1.1 Radiated Emission measurement set up, rear view, full configuration...........................................................................4 1.2 Radiated Emission measurement set up, rear view, with small V-sense ........................................................................5 1.3 Radiated Emission measurement set up, rear view, with medium V-sense....................................................................6 1.4 Radiated Emission measurement set up, front view, with large V-sense .......................................................................7 2 Test setup photographs of conducted emission measurements...............................................................................................8 Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 4 of 9 1 Test setup photographs of radiated emission measurements. 1.1 Radiated Emission measurement set up, rear view, full configuration Photo 1: Radiated Emission measurement set up, rear view, full configuration. Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 5 of 9 1.2 Radiated Emission measurement set up, rear view, with small V-sense Photo 2: Radiated Emission measurement set up, front view, with small V-sense, rear view Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 6 of 9 1.3 Radiated Emission measurement set up, rear view, with medium V-sense Photo 3: Radiated Emission measurement set up, rear view, with medium V-sense Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 7 of 9 1.4 Radiated Emission measurement set up, front view, with large V-sense Photo 4: Radiated Emission measurement set up, front view, with large V-sense Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 8 of 9 2 Test setup photographs of conducted emission measurements Photo 5: Conducted Emission measurement set up Description of EUT: Manufacturer: Brand mark: Model: Inductive proximity tag reader N.V. Nederlandsche Apparatenfabriek NEDAPî NEDAP SF-4 Project number: 06020907.p03 Page 9 of 9 Photo 6: Conducted emission measurement set up