CGDLW245ALuxon Wireless LW245A

Installation Manual L L. Hones 11 August 2013 Page 1 of 5 Installation Manual Luxon Wireless 245A 1. Brief product description The Luxon Wireless 245A can be added to wireless communication between the installation the Luxon Wireless 245A wirelessly to and from the light controller. Figure 1. Installation example with Luxon Wireless Page 2 of 5 can be added to a fixture equipped with a Luxon e-HID ballast. It communication between the electronic ballast and the Luxon Light Controller (LLC). A becomes a RF node in the network, and data can be the light controller. Luxon Wireless HID lamps in a building with skylights HID ballast. It facilitates and the Luxon Light Controller (LLC). After data can be transferred HID lamps in a building with skylights 2. Product description Figure 2: LW245A module The Luxon Wireless 245A comes mounted into a protective module as shown in Figure 2. This cable is used for both powering the module and the wired communication with the ballast. Avoid disconnecting the quite The black connector is a 4 po le female connector with polaris of Luxon e-HID ballasts. The module comes with 2 3. Warnings Always disconnect the ballast from mains power prior to connecting the Luxon Wireless 245A After making the connection to the Luxon Wireless 245A module carry life voltage. Sufficient creepage distance must be kept towards other conductors and enclosure parts. The enclosure is designed to comply with safety standards. The Luxon Wireless 245A module may only be installed 4. Mounting instructions The Luxon Wireless 245A module must transceiver have the best possible unobstructed line of sight to other Luxon Wireless nodes. For best performance let the transceiver have a 360 degree field of sight. The module requires a 23mm diameter with 30mm spacing, see also Figure 5 The provided two self tapping screws The sealing can be used if IP65 ingress Page 3 of 5 Figure 3: mounting hardware comes mounted into a protective plastic enclosure. The cable . This cable is used for both powering the module and the wired Avoid disconnecting the quite fragile cable connector from the module. le female connector with polarisation and locking, for use with The module comes with 2 Torx T10 bolts and a protective sealing, see Fig 3 lways disconnect the ballast from mains power prior to connecting the Luxon Wireless 245A Luxon ballast and powering up, the electronic circuits on the Luxon Wireless 245A module carry life voltage. It must be made impossible to end users touching the life parts. be kept towards other conductors and enclosure parts. The enclosure is designed to comply with safety standards. The Luxon Wireless 245A module may only be installed by qualified and trained personnel instructions The Luxon Wireless 245A module must be mounted to the outside of the luminaire, to let the RF best possible unobstructed line of sight to other Luxon Wireless nodes. best performance let the transceiver have a 360 degree field of sight. See also the Figure 4. a 23mm diameter hole to pop through, together with two 3mm holes f 30mm spacing, see also Figure 5. The mounting area shall be flat. rews shall be used to secure the module. ingress protection is required. cable is plugged into the . This cable is used for both powering the module and the wired fragile cable connector from the module. ation and locking, for use with specific series a protective sealing, see Fig 3. lways disconnect the ballast from mains power prior to connecting the Luxon Wireless 245A. ballast and powering up, the electronic circuits on the Luxon ers touching the life parts. be kept towards other conductors and enclosure parts. nel. , to let the RF best possible unobstructed line of sight to other Luxon Wireless nodes. See also the Figure 4. , together with two 3mm holes for the screws Figure 4: Sample application 5. Connecting The cable is used to make a connection with the ballast. The polarization and locking. Please insert Note that it might be necessary to remove a small protection cover connector. Please note that the cable to the ballast electrical interference. See also Figure 7. Figure 6: connection to ballast (example) Page 4 of 5 Figure 5: enclosure cut-out dimensions The cable is used to make a connection with the ballast. The black connector has provisions for both Please insert it carefully into the counterpart on the ballast. See also Figure 6. to remove a small protection cover from the ballast that is to the ballast shall be kept away from the lamp output cable to minimize See also Figure 7. connection to ballast (example) Figure 7: example assembly out dimensions connector has provisions for both See also Figure 6. from the ballast that is located over the cable to minimize Figure 7: example assembly 6. Specifications 7. FCC and IC Declarations FCC ID: CGD Compliance statement This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ Déclaration Conformité Cet appareil se conforme aux normes RSS exemptés de L'opération est soumis aux deux conditions suivantes (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Warning Changes or modifications not expressly approved authority to operate the equipment. RF Exposure To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. 8. Label artwork example for a fixture with LW245A module Operating temperature Safety EMC/Telecom -40 to EN60950 EN301489 FCC47 part Dimensions 50 X 36 mm Input Supply 3.3 Vdc, +/ Max. 100mA Page 5 of 5 CC ID: CGDLW245A and IC: 1444A-L…

Text truncated - open the document above for the full version.

N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Groenlo, 17 August 2013 Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Board Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Dear Mrs. Bosley, We, N.V. Nederlandsche Apparatenfabriek "Nedap", we hereby would like to apply for Limited Modular Approval certification of the following device: FCC ID : CGDLW245A FRN : 0007696149 Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A Description : A Digital Transmission System in the band 2408 – 2475 MHz Type of service : New application, Limited Modular approval The following PDF files (exhibits) are electronically submitted: 1. Cover letter (this document) 2. Request of confidentiality 3. Application form 4. Antenna information 5. Bill of material (BOM) 6. Circuit diagram 7. Block diagram 8. Photographs of the PCB Sensor Bridge 9. Photographs of Sensor Bridge Wall Mount, an example application 10. Label artwork and - location 11. Theory of operation 12. Test report 13. Test setup photographs 14. Installation manual 15. RF Exposure 16. Brochure 17. Request putting statement 15.19 (a)(3) in the manual 18. Modular approval statement 19. Block diagram Nordic nRF2401A NOTE: We would like to request for the 15.19 (a) (3) statement to go in the manual due to size. Best regards, N.V. Nederlandsche Apparatenfabriek “Nedap“ Jacques Hulshof Approbation Officer

N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Body Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Groenlo, 07 August 2013 Subject: Request of Confidentiality FCC ID: CGDLW245A Dear Mrs. Bosley, Pursuant to section 0.457(d)(2)(i) and Section 0.459 of the FCC rules we herewith request the following exhibits, related to this application for FCC ID : CGDLW245A Applicant : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A Type of service : New application, Limited Modular approval to be withheld from public inspection and to be kept confidential. The contents of these exhibits may not be disclosed to other parties than N.V. Nederlandsche Apparatenfabriek "Nedap" and TÜV Rheinland Electronic Products & Services (EPS) B.V.: 1. Bill of materials 2. Circuit diagram 3. Block diagram 4. Theory of operation (technical description) The reason for this request for confidentiality is that the information contained in the exhibits as listed above has been classified as company confidential. Disclosure of any portion of this information to other parties would cause substantial competitive harm. Best regards, N.V. Nederlandsche Apparatenfebriek “Nedap” Jacques Hulshof Approbation officer

N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Request putting statement 15.19(a)(3) in the manual Groenlo, 11 August 2013 Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Board Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Subject : Request putting labeling of statement 15.19 (a) (3) in manual FCC ID: CGDLW245A Dear Mrs. Bosley, We, N.V. Nederlandsche Apparatenfabriek “Nedap”, declare that it is hardly possible to add the statement as mentioned in Part15.19 (a) (3): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. next to the FCC ID, model number or the brand name on the bottom of the product due to size restrictions. There for we request the above mentioned statement be allowed to be in the manual, due to size and not able to add a sticker, based on the 2.935/2.936 rule part. I hope you can honor our request Best regards, N.V. Nederlandsche Apparatenfebriek “Nedap” Jacques Hulshof Approbation officer

N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Body Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Subject: Statement requirements modular approval FCC Part 15.212 Groenlo, 11 August 2013 Dear Mrs. Bosley, Pursuant to section 0.457(d)(2)(i) and Section 0.459 of the FCC rules we herewith request the following exhibits, related to this application for FCC ID : CGDLW245A Applicant : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A FCC ID : CGDLW245A Type of service : New application, Limited Modular approval We would like above product have approved as a modular approval specific to FCC Part 15.212 Limited Modular Transmitter Unlicensed Approval for low power transmitter modules for use in Nedap’s host devices: The requirements of the FCC Part 15.212 are met as follows: 1. The modular transmitter nRF2401A on the Luxon Wireless 245A module has an own RF shielding in order to be compliant to the FCC rules. See Exhibit “08_Photo Report Int CGDLW245A.pdf”. 2. The modular transmitter nRF2401A has buffered data inputs with a buffer of maximum 256 bits and a maximum data rate of 1000 kbps see page 10 of exhibit “19_Blockdiagram Nordic nRF2401A CGDLW245A.pdf”. 3. The modular transmitter nR2401A has its own power supply regulation for its RF circuits and requires an input voltage of 3.3 Vdc. The voltage is derived from the input voltage of the LW245A module, via an LC filter. 4. An integral antenna is applied see exhibit “04_Antenna information CGDLW245A.pdf”. 5. The EUT was tested stand alone, powered by an external 3.3Vdc source. 6. An exhibit label (including FCC ID) has been included in the exhibits “10_Label location_artwork CGDLW245A.pdf. This device is only installed in Nedap’s end products and “14_Installation manual Luxon Wireless CGDLW245A.pdf” shows and instructs in what manner the end product needs labeling. 7. The Luxon Wireless 245A is compliant with all applicable FCC rules. Instructions for maintaining compliance are given in the “14_Installation manual Luxon Wireless CGDLW245A.pdf. 8. The Luxon Wireless 245A is compliant with all applicable RF exposure requirements for transmitter devices. N.V. Nederlandsche Apparatenfabriek “Nedap” Jacques Hulshof Approbation officer

Page 1 of 5 Limited Modular Approval Digital Transmission System Brand Nedap Model Luxon Wireless 245A External Photographs Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Luxon Wireless LW245A CGDLW245A 1444A-LW245A Page 2 of 5 Description of item Description of EUT : A Digital Transmission System in the band 2408 – 2475 MHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Luxon Wireless LW245A Model : Sensor Bridge Wall Mount FCC ID : CGDLW245A IC : 1444A-LW245A Type of service : New application, Limited Modular approval Applicant information Applicant's representative : Mr. Jacques Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 544 471111 Telefax number : +31 544 463475 11 August 2013 Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Luxon Wireless LW245A CGDLW245A 1444A-LW245A Page 3 of 5 Table of contents 1 TOTAL OVERVIEW .......................................................................................................................................................... 4 2 ENCLOSURE ....................................................................................................................................................................... 5 Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Luxon Wireless LW245A CGDLW245A 1444A-LW245A Page 4 of 5 1 Total overview Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Luxon Wireless LW245A CGDLW245A 1444A-LW245A Page 5 of 5 2 Enclosure

Page 1 of 5 Limited Modular Approval Digital Transmission System Brand Nedap Model Luxon Wireless 245A Label Location Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Page 2 of 5 Description of item Description of EUT : Digital Transmission System Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A FCC ID : CGDLW245A IC : 1444A-LW245A Type of service : New application, Limited Modular approval Applicant information Applicant's representative : Mr. Jacques Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 11 August 2013 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Page 3 of 5 Table of contents 1 LABEL LOCATION ............................................................................................................................................................. 4 2 LABEL ARTWORK ............................................................................................................................................................ 5 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Page 4 of 5 1 Label location Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Page 5 of 5 2 Label artwork

Page 1 of 6 Limited Modular Approval Digital Transmission System Brand Nedap Model Luxon Wireless 245A Interior Photographs Description of EUT: Manufacturer: Brand mark: FCC ID: IC: Model: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap CGDLW245A 1444A-LW245A Luxon Wireless 245A Page 2 of 6 Description of item Description of EUT : A Digital Transmission System in the band 2408 – 2475 MHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A FCC ID : CGDLW245A IC : 1444A-LW245A Type of service : New application, Limited Modular approval Applicant information Applicant's representative : Mr. Jacques Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 11 August 2013 Description of EUT: Manufacturer: Brand mark: FCC ID: IC: Model: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap CGDLW245A 1444A-LW245A Luxon Wireless 245A Page 3 of 6 Table of contents 1 OVERVIEW OF THE LUXON WIRELESS 245A ........................................................................................................... 4 1.1 PCB FRONT VIEW, COMPONENT SIDE ........................................................................................................................... 4 1.2 PCB FRONT VIEW, COMPONENT SIDE, METAL SHIELD REMOVED.................................................................................. 5 1.3 PCB BACK SIDE .............................................................................................................................................................. 6 Description of EUT: Manufacturer: Brand mark: FCC ID: IC: Model: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap CGDLW245A 1444A-LW245A Luxon Wireless 245A Page 4 of 6 1 Overview of the Luxon Wireless 245A 1.1 PCB Front view, component side Description of EUT: Manufacturer: Brand mark: FCC ID: IC: Model: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap CGDLW245A 1444A-LW245A Luxon Wireless 245A Page 5 of 6 1.2 PCB Front view, component side, metal shield removed Description of EUT: Manufacturer: Brand mark: FCC ID: IC: Model: Digital Transmission System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap CGDLW245A 1444A-LW245A Luxon Wireless 245A Page 6 of 6 1.3 PCB back side

N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Groenlo, 11 August 2013 Declaration on radiation safety standard conformance To whom it may concern: N.V. Nederllandsche Apparatenfabriek “Nedap” Parallelweg 2 7141 DC Groenlo The Netherlands declares that the following product Description : A Digital Transmission System in the band 2408 – 2475 MHz FCC ID : CGDLW245A Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A Type of service : New application, Limited Modular approval has a rated RF power of 1.37 mW, which means that the worst case prediction of power density (100% reflection) at 20 cm distance (worst case) can be calculated as follows: 2 **4R EIRP S π = (power density without reflection) 2 2 **4 *2 R EIRP S π = (power density with 100% reflection) 2 2 **4 *2 R EIRP S π = = 2 )20(* 37.1 cm mW π = 0.0011 mW/cm² (Limit = 0.2 mW/cm²) N.V. Nederlandsche Apparatenfabriek “Nedap” Jacques Hulshof Approbation officer

Testing and certification of electronic and electric appliances, systems, installations and telecommunication systems TÜV Rheinland EPS P.O. Box 37 9350 AA Leek (NL) Eiberkamp 10 9351 VT Leek (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.tuv-eps.com Project number: 13041503.fcc01_Rev01 Page 1 of 24 TEST REPORT CONCERNING THE COMPLIANCE OF A DIGITAL TRANSMISSION SYSTEM OPERATING IN THE FREQUENCYRANGE 2408 – 2475 MHZ, BRAND NEDAP, MODEL Luxon Wireless 245A WITH 47 CFR PART 15 (10-1-12 Edition) and RSS-Gen (issue 3, December 2010) and RSS-210 (Issue 8, December 2010) 13041503.fcc01_Rev01 September 16,2013 FCC listed Industry Canada R&TTE, LVD, EMC Notified Body : : : : 90828 2932G-2 1856 Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: 47 CFR Part 15 and RSS Digital Transmission System Nedap Light Controls Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Project number : 13041503.fcc01_Rev01 Page 2 of 24 MEASUREMENT/TECHNICAL REPORT N.V. Nederlandsche Apparatenfabriek “Nedap” Model : Luxon Wireless 245A FCC ID: CGDLW245A IC: 1444A-LW245A This report concerns: Original grant,certification / Limited Single Modular Approval Class 2 change Verification Equipment type: Digital Transmission System (DTS) Report prepared by: Name : Richard van der Meer Company name : TÜV Rheinland EPS Address : Eiberkamp 10 Postal code/city : 9351VT Leek Mailing address : P.O. Box 37 Postal code/city : 9350AA Leek Country : The Netherlands Telephone number : + 31 594 505 005 Telefax number : + 31 594 504 804 E-mail : [email protected] The data taken for this test and report herein was done in accordance with 47 CFR Part 15 (10-1-12 Edition), RSS-Gen (issue 3, December 2010) and RSS-210 (Issue 8, December 2010) and the measurement procedures of ANSI C63.10-2009. TÜV Rheinland EPS at Leek, The Netherlands, certifies that the data is accurate and contains a true representation of the emission profile of the Equipment Under Test (EUT) on the date of the test as noted in the test report. I have reviewed the test report and find it to be an accurate description of the test(s) performed and the EUT so tested. Date: September 16, 2013 Signature: O. Hoekstra Senior Engineer Telecom TÜV Rheinland EPS Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: 47 CFR Part 15 and RSS Digital Transmission System Nedap Light Controls Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Project number : 13041503.fcc01_Rev01 Page 3 of 24 Description of test item Test item : Digital Transmission System operating in the range 2408-2475 MHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A Serial number : n.a. Revision : n.a. Applicant information Applicant's representative : Mr. J. Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo Country : The Netherlands Telephone number : +31 544 471 162 Telefax number : +31 544 463 475 E-mail : [email protected] Test(s) performed Location : Leek Test(s) started : June 19, 2013 Test(s) completed : June 27, 2013 Purpose of test(s) : Equipment Authorization (Original grant/certification) / Limited Single Modular Approval Test specification(s) : 47 CFR Part 15 (10-1-12 Edition) and RSS-GEN (ISSUE 3, DECEMBER 2010) AND RSS-210 (ISSUE 8, DECEMBER 2010). Test engineer(s) : R. van der Meer Report written by : R. van der Meer Report date : September 16, 2013 This report shall not be reproduced, except in full, without the written permission of TÜV Rheinland EPS. The test results relate only to the item(s) tested. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: 47 CFR Part 15 and RSS Digital Transmission System Nedap Light Controls Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Project number : 13041503.fcc01_Rev01 Page 4 of 24 Table of contents 1 General information. .............................................................................................................................................. 5 1.1 Product description. ........................................................................................................................................ 5 1.1.1 Introduction. ............................................................................................................................................ 5 1.2 Related submittal(s) and/or Grant(s). ............................................................................................................. 5 1.2.1 General. .................................................................................................................................................. 5 1.3 Tested system details. .................................................................................................................................... 5 1.3.1 Description of input and output ports. ..................................................................................................... 7 1.4 Test results summary ..................................................................................................................................... 8 1.5 Test methodology. .......................................................................................................................................... 9 1.6 Test facility. .................................................................................................................................................... 9 1.7 Test conditions. .............................................................................................................................................. 9 2 System test configuration. ................................................................................................................................... 10 2.1 Justification. ..........................................................…

Text truncated - open the document above for the full version.

Testing and certification of electronic and electric appliances, systems, installations and telecommunication systems TÜV Rheinland EPS P.O. Box 37 9350 AA Leek (NL) Eiberkamp 10 9351 VT Leek (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 Internet: www.tuv-eps.com E-mail: [email protected] Project number: 13022201.p01 Page 1 of 7 PHOTOGRAPHS OF THE TESTSETUP OF A DIGITAL TRANSMISSION SYSTEM OPERATING IN THE FREQUENCYRANGE 2408 – 2475 MHz, BRAND NEDAP, MODEL Luxon Wireless 245A, 13041503.p01 June 27, 2013 FCC listed Industry Canada R&TTE, LVD, EMC Notified Body : : : : 90828 2932G-2 1856 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System Nedap Light Controls Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Project number: 13041503.p01 Page 2 of 7 Description of test item Test item (EUT) : Digital Transmission System operating in the range 2408-2475 MHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : Luxon Wireless 245A Serial number(s) : n.a. FCC ID : CGDLW245A IC : 1444A-LW245A Receipt date : June 19,2013 Applicant information Applicant's representative : Mr. J. Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo Country : The Netherlands Telephone number : +31 544 471 162 Telefax number : +31 544 466 475 E-mail : [email protected] Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Digital Transmission System Nedap Light Controls Nedap Luxon Wireless 245A CGDLW245A 1444A-LW245A Project number: 13041503.p01 Page 3 of 7 Table of contents 1 PHOTOGRAPHS OF THE TESTSETUP. ....................................................................................................................... 4 1.1 RADIATED EMISSIONS..................................................................................................................................................... 4 1.1.1 Front view.......................…

Text truncated - open the document above for the full version.