
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be repro- duced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP. doc. article no: 5278988 chk: rev. : C.01 drw: CB 2013/06/13 sheet: 45.01 of 1 drawing: T5278-988 !D Gate dimensions GROENLO - HOLLAND 462 10 (oorpart) 1668 195,5 828,75 1024,25 300 150(2x) 60(2x) 13(6x) 70 100 57 sales floor stock room orientation in the shop all antennas in the same direction. distance between antennas 1x !D Gate1x Coax cable 3m/10ft description: quick reference !D Gate AB Power inserter recommended - 2.0m / 6.5ft absolute max. - 2.2m / 7ft AB AB AB AB AB AB 462mm / 18.2” 1668mm / 5.7ft 828.75mm / 2.7ft 195.5mm / 7.7” 1024.25mm / 3.4ft 100mm / 3.9” 57mm / 2.2” 70mm / 2.8” Reinforced Concrete Iron Reinforced Concrete Nylon Insulation ring (included in installation set) Retainer ring (not included in installationset) Iron Always mount an antenna insulated to the floor or wall Nut (not included in installationset) Nylon M10 (included in installation set) 4x M10 2 4 1 Metal M10 3 0403 Hilti-hit not included Cleaning Hilti-hitPlace nut 05 300 150 60 13 (6x) 90mm / 3.5” ø 13mm / ø 0.5” 02 remove covers 01 drilling holes Nut (not included in installationset) Retainer ring (not included in installationset) Nylon Insulation ring (included in installationset) Always mount an antenna insulated to the floor or wall 300mm / 11.8” 150mm / 5.9” 13mm / 0.5” 60mm / 2.4” processing unit network IN network OUT USB service port USB host Power for Reader Recommended to place in switch-room power supply Out In Power supply 9561811. One needed for every installed system. (not included) 1YellowHeartbeat 2GreenDisk access 3GreenFirmware running 12 3 + - buzzer Not compatible with IEEE 802.3a* standard C D E F 10 7 2 1 F E 8 11 12 9 3 4 5 6 G H G H C D E F 10 7 2 1 F E 8 11 12 9 3 4 5 6 G H G H LedBlueOrangeRedGreenGreen - Firmware runningErrorRFID activePower next previous !D Reader 1GreenProcessing unit at output 2BlueBlinkNo device at output or Lan- modem (in case of OST integration) BlueContinuousPower inserter at output 3RedPower error coax cable 3m / 10ft 2x coax cable 3m / 10ft no coax cable needed recommended label free zone 1m / 3ft required label free zone 1m / 3ft 1m / 3ft 1m / 3ft 2m / 6ft2m / 6ft 0.5m / 1.5ft 0.5m / 1.5ft place covers 230V 110V connect voltage supply Note : The start up of all the processes takes approximately 3 minutes. 02 use firmware configuration quick reference. next coax-cable 3m/10ft 21 01 Minimum bending radius = >60mm/2.4” previous coax cable coax cable RJ45 connector to ethernet outlet - customer network. processing unit network IN 2 OUT IN note: use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable) 1 processing unit network IN 03 processing unit network OUT RJ45 connector to ethernet outlet - customer network. 2 note: use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable) 1 Model: !D Gate Region 2 FCC ID: CGDSTOREIDG IC: 1444A-STOREIDG This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada. L’opération est soumis aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Les changements ou modifications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel. FCC and IC Radiation Exposure Statement: This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncon- trolled environment. This equipment should be installed and operated with a minimum distance of 3.65 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme a RSS-102 limites énoncées pour un environne- ment non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 3.65 cm entre le radiateur et votre corps. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003
N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Groenlo, 27 May 2013 Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Body Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Dear Mrs. Bosley, We, N.V. Nederlandsche Apparatenfabriek "Nedap", hereby would like to apply for FCC certification of the following device: FCC ID : CGDSTOREIDG FRN : 0007696149 Brand : Nedap Model : !D Gate Region 2 Type of Service : New Application Description : UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System (FAP) operating in the band 7.400 – 8.800 MHz and a metal detection module operating on 125 kHz with an option to communicate with the outside world via LAN Type: XPORT-03 by Lantronix The following PDF files (exhibits) are electronically submitted: 1. Cover letter (this document) 2. Request of Long-Term confidentiality 3. Application form 731 4. Antenna information (2 provided, 4a and 4b) 5. Bill of material (2 provided, 5a and 5b) 6. Circuit diagrams (2 provided, 6a and 6b) 7. Block diagram (3 provided, 7a1, 7a2 and 7b) 8. Interior photograph report 9. Exterior photograph report 10. Label location incl. label 11. Theory of Operation 12. Test report in conformity with 47 CFR Part 15 (2 provided, 12a and 12b) 13. Test setup photographs 14. Install Manual 15. Brochure 16. Declaration on radiation safety standard conformance Best regards, N.V. Nederlandsche Apparatenfabriek “Nedap“ Jacques Hulshof Approbation Management
N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Return address: PO Box 6, 7140 AA Groenlo, The Netherlands ACB Attn.: Mrs. M. Bosley American Certification Body Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA Groenlo, 27 may 2013 Subject: Request of permanent confidentiality FCC ID: CGDSTOREIDG Dear Mrs. Bosley, Pursuant to section 0.457(d)(2)(i) and Section 0.459 of the FCC rules N.V. Nederlandsche Apparatenfabriek “Nedap” herewith request the following exhibits, related to this application for: FCC ID : CGDSTOREIDG Manufacurer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : !D Gate Region 2 Description : UHF Reader with antenna !D Gate operating on 902-928 MHz as permanently confidential, be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. The contents of these exhibits may not be disclosed to other parties than N.V. Nederlandsche Apparatenfabriek "Nedap" and TÜV Rheinland Nederland B.V.: 1. Bill of materials 2. Circuit diagram 3. Block diagram 4. Theory of operation (technical description) Best regards, N.V. Nederlandsche Apparatenfabriek “Nedap” Jacques Hulshof Approbation Management
Page 1 of 6 UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System operating in the band 7.400 – 8.800 MHz and a metal detection module operating on 125 kHz Brand Nedap Model: !D Gate Region 2 Exterior Photographs Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC Type of Application UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 2 of 6 Description of item Description of EUT : UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System operating in the band 7.400 – 8.800 MHz and a metal detection module operating on 125 kHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : !D Gate Region 2 FCC ID : CGDSTOREIDG IC : 1444A-STOREIDG Type of Service : New Application Applicant information Applicant's representative : Mr. Jacques Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 27 May 2013 Rev. 29 May 2013 Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC Type of Application UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 3 of 6 Table of contents 1 EXTERNAL PHOTOGRAPH OF THE !D GATE REGION 2 ....................................................................................... 4 1.1 FRONT SIDE ..................................................................................................................................................................... 4 1.2 BACK SIDE ....................................................................................................................................................................... 5 2 LABELING OF THE POWER SUPPLIES ....................................................................................................................... 6 2.1 POWER INSERTER ............................................................................................................................................................ 6 2.2 POWER SUPPLY INSIDE NCC ........................................................................................................................................... 6 Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC Type of Application UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 4 of 6 1 External Photograph of the !D Gate Region 2 1.1 Front side 902-928 MHz antennae Inductive EAS and MD antenna wiring Transceivers, processing unit and RF-antenna adjusting board NCC synchronization unit with PS Power Inserter Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC Type of Application UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 5 of 6 1.2 Back side Description of EUT: Manufacturer: Brand mark: Model: FCC ID IC Type of Application UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandse Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 6 of 6 2 Labeling of the Power supplies 2.1 Power inserter 2.2 Power Supply inside NCC
Page 1 of 5 UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System operating in the band 7.400 – 8.800 MHz and a metal detection module operating on 125 kHz Brand Nedap Model: !D Gate Region 2 Label Location and Label photographs Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Type of Service: UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandsche Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 2 of 5 Description of item Description of EUT : UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System operating in the band 7.400 – 8.800 MHz and a metal detection module operating on 125 kHz Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : !D Gate Region 2 FCC ID : CGDSTOREIDG IC : 1444A-STOREIDG Type of Service : New Application Applicant information Applicant's representative : Mr. Jacques Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo PO-box : 6 Postal code : 7140 AA City : Groenlo Country : The Netherlands Telephone number : +31 (0) 544 471111 Telefax number : +31 (0) 544 463475 27 May 2013 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Type of Service: UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandsche Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 3 of 5 Table of contents 1 Location of the label .................................................................................................................................................................... 4 2 IC-FCC ID label .......................................................................................................................................................................... 5 2.1 Total overview ..................................................................................................................................................................... 5 2.2 FCC ID and IC label ............................................................................................................................................................ 5 2.3 Warning label ...................................................................................................................................................................... 5 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Type of Service: UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandsche Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 4 of 5 1 Location of the label Warning label Model number IC, FCC ID Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: Type of Service: UHF Reader with antenna FL45-N operating on 902-928 MHz including an Anti Pilferage System N.V. Nederlandsche Apparatenfabriek “Nedap” Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG New Application Page 5 of 5 2 IC-FCC ID label 2.1 Total overview 2.2 FCC ID and IC label 2.3 Warning label
N.V. Nederlandsche Apparatenfabriek “Nedap” Parallelweg 2 NL-7141 DC Groenlo P.O. Box 6 NL-7140 AC Groenlo T +31 (0)544 471 111 F +31 (0) 544 463 475 E [email protected] www.nedap.com Traderegister 08013836 ABN-AMRO 59.16.32.330 IBAN NL83ABNA0591632330 BIC ABNANL2A VAT NL006456285B01 The General Terms & Conditions of ICT-Office apply to all our offers and agreements. These conditions can be found at our website www.nedap.com and can be provided upon request. Groenlo, 27 May 2013 Declaration on radiation safety standard conformance Return address: PO Box 6, 7140 AA Groenlo, The Netherlands American Certification Body Attn.: Mrs. M. Bosley Certification Department 6731 Whittier Avenue, Suite C110 McLean, Virginia 22101 USA We, N.V. Nederlandsche Apparatenfabriek “Nedap”, declare that the following product: Description : UHF Reader with antenna !D Gate operating on 902-928 MHz FCC ID : CGDSTOREIDG Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : !D Gate Region 2 has a maximum conducted peak power of 28.5 dBm equals 707.9 mW. With an antenna gain of 5.8 dBi (3.802x) this comes down to 2691 mW peak in the frequency range of 902 – 928 MHz. which means that the power density at 20 cm distance can be calculated as follows : S = Ppeak/4*π * R 2 (power density) Ppeak = 2691 mW S = Ppeak / 4*π * R 2 = 2691 / 4*π*(20cm) 2 = 0.535 mW/cm 2 The limit is 1.0 mW/cm 2 This means that according to OET Bulletin 65 (Edition 97-01), Supplement C (Edition 01-01), the equipment fulfills the requirements on power density for general population/uncontrolled exposure and therefore fulfills the requirements of 47 CFR Part 15.247 (b)(5). N.V. Nederlandsche Apparatenfabriek “Nedap” Jacques Hulshof Approbation Management The limit is 0.601 mW/cm 2 (902 MHz/1500)
Testing and certification of electronic and electric appliances, systems, installations and telecommunication systems TÜV Rheinland EPS B.V. P.O. Box 37 9350 AA Leek (NL) Eiberkamp 10 9351 VT Leek (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 Internet: www.tuv-eps.com E-mail: [email protected] Project number: 13031902.p01_Rev01 Page 1 of 10 PHOTOGRAPHS OF THE TESTSETUP OF AN UHF RFID reader, OPERATING IN THE FREQUENCYBAND 902-928 MHz BRAND NEDAP, MODEL !D Gate Region 2 13031902.p01_Rev01 June 04, 2013 FCC listed Industry Canada R&TTE, LVD, EMC Notified Body : : : : 90828 2932G-2 1856 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 2 of 10 Description of test item Test item (EUT) : UHF RFID reader (Spread Spectrum Transmitter (DSS)) Manufacturer : N.V. Nederlandsche Apparatenfabriek “Nedap” Brand : Nedap Model : !D Gate Region 2 Serial number(s) : D408 006 and D408 010 FCC ID : CGDSTOREIDG IC : 1444A-STOREIDG Receipt date : April 25, 2013 Applicant information Applicant's representative : Mr. J. Hulshof Company : N.V. Nederlandsche Apparatenfabriek “Nedap” Address : Parallelweg 2 Postal code : 7141 DC City : Groenlo Country : The Netherlands Telephone number : +31 544 471 162 Telefax number : +31 544 466 475 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 3 of 10 Table of contents 1 PHOTOGRAPHS OF THE TESTSETUP. ....................................................................................................................... 4 1.1 RADIATED EMISSIONS..................................................................................................................................................... 4 1.1.1 Front view.............................................................................................................................................................. 4 1.1.2 Front and Rear view of EUT setup .................................................................................................................... 6 1.2 CONDUCTED TESTS ........................................................................................................................................................ 8 1.3 CONDUCTED EMISSIONS ................................................................................................................................................ 9 1.3.1 Front view.............................................................................................................................................................. 9 1.3.2 Rear view ............................................................................................................................................................ 10 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 4 of 10 1 Photographs of the testsetup. 1.1 Radiated emissions. 1.1.1 Front view Photo showing setup for 0.009 – 30 MHz Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 5 of 10 Photo showing setup for 30 – 1000 MHz Photo showing setup for 1 – 10 GHz (restricted band measurements) Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 6 of 10 1.1.2 Front and Rear view of EUT setup Front view of the EUT setup Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 7 of 10 Rear view of the EUT setup (USB and Ethernet connection shown) Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 8 of 10 1.2 Conducted tests Antennaport Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 9 of 10 1.3 Conducted emissions 1.3.1 Front view Description of EUT: Manufacturer: Brand mark: Model: FCC ID: IC: UHF RFID reader N.V. Nederlandsche Apparatenfabriek Nedap Nedap !D Gate Region 2 CGDSTOREIDG 1444A-STOREIDG Project number: 13031902.p01_Rev01 Page 10 of 10 1.3.2 Rear view
Parallelweg 2 · Groenlo · Netherlands
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 7.52 MHz - 8.756 MHz | - |

VP1004-B System
Equipment Class
DCD - Part 15 Low Power Transmitter Below 1705 kHz
SMARTTAG EAR
Equipment Class
DXX - Part 15 Low Power Communication Device Transmitter
Reader for 120 kHz and 13.56 MHz cards and also NFC, QR and BT
Equipment Class
DCD - Part 15 Low Power Transmitter Below 1705 kHz
Long-range vehicle and driver identification tag
Equipment Class
DSR - Part 15 Remote Control/Security Device Transceiver
4kW Electronic Lamp Driver
Equipment Class
DTS - Digital Transmission System