CJ6UPA3234WL802.11 a/b Mini-PCI WLAN Module

Wireless LAN Card Features The Wireless LAN Card is a wireless network card that fits into a Mini-PCI TypeIII slot. Wireless LAWireless LAN Card TypesN Card Types The Wireless LAN Card is a wireless network card that complies with the IEEE 802.11 standard on wireless LANs (Revision A, B), Revision A supports data rates up to 54 Mbit/s. Revision B supports data rates up to 11 Mbit/s. n Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. This means that your Wireless hardware will communicate with other vendors’ IEEE 802.11 compliant wireless LAN product. The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance. n Fully compatible with any other wireless LAN system based on Direct Sequence Spread Spectrum (DSSS)/ Orthogonal Frequency Division Multiplexing (OFDM) radio technology that complies with the “IEEE 802.11 standard on wireless LANs (Revision A or B). Wireless LAN CardsWireless LAN Cards The Wireless LAN Card supports the following wireless LAN features: n Automatic Transmit Rate Select mechanism in the transmit range of 54,48,36,24,18,12, 9 and 6 Mbit/s. (Revision A) n Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1 Mbit/s. (Revision B) n Frequency Channel Selection (5GHz:Revision A / 2.4GHz:Revision B). n Roaming over multiple channels. n Card Power Management. n Wired Equivalent Privacy (WEP) data encryption, based on 128bit encryption algorithm. n Card Specifications Card Specifications Form Factor - Mini PCI TypeIII Capability - IEEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. Network Operating - Microsoft Windows® Networking System Media Access Protocol - CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate - 54/48/36/24/18/12/9/6 Mb/s (Revision A) - 11/5.5/2/1 Mb/s (Revision B) Radio CharacteristicsRadio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: n country/region where the product was purchased n Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN Wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment. NOTE: NOTE: Refer to the flyer "Information to the User” for regulatory information that may apply in your country/region. R-F Frequency -Band 5GHz (5150-5850 MHz) (Revision A) -Band2.4GHz (2400-2483.5 MHz) (Revision B) Modulation Technique -DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) -OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A) The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at lower Transmit range may travel larger distances. n The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. n Range is also impacted due to “obstacles” in the signal path of the radio that may either absorb or reflect the radio signal. Supported Frequency SubSupported Frequency Sub--bandsbands Subject to the radio regulations that apply in your country, your Wireless LAN Card may support a different set of 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region. Wireless IEEE 802.11 Channels Sets (Revision B) Frequency Range Channel ID 2400-2497 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 1010 2457*2457* *1) 11 2462 12 2467 *2) 13 2472 *2) 14 2484 *3) *1) Factory-set default channels *2) Available Area: All approved regions except USA, Canada, and TAIWAN. *3) Available Area: Japan 802.11b mode only When installing Wireless LAN Cards, the channel configuration is managed as follows: n For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required. n For Wireless LAN Cards installed in Wireless clients that operating in a peer-to-peer mode, the card will use the default channel 10. n In a Wireless LAN Access Point, the Wireless LAN card will use the factory-set default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device. Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range 5150-5850 MHz Note Channel ID 36 5180 *1 40 5200 *1 44 5220 *1 48 5240 *1 52 5260 *1 56 5280 *1 60 5300 *1 64 5320 *1 149 5745 US only *2 153 5765 US only *2 157 5785 US only *2 161 5805 US only *2 *1: Refer to Table1 about the Europe area. USA and CANADA are available. *2: Available Area: US (USA, CANADA) only Table1:A table of allowed frequency ranges within Europe Country/Region 5150-5250 MHz 5250-5350 MHz 5470-5725 MHz (*1) 5725-5850 MHz Austria, Belgium, Italy, Lichtenstein, Switzerland  × × × Denmark, Finland, France, Germany, Ireland, Netherlands, Portugal, Sweden, UK    × Luxemburg, Norway ×   × Greece, Iceland, Spain × × × × : allowed ×: forbidden *1) PA3234U-1MPC is not available in this frequency band. Information sheet Wireless Interoperability The Intel(R) PRO/Wireless LAN 2100A 3B Mini PCI Adapter products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS)/Orthogonal Frequency Division Multiplexing(OFDM) radio technology, and is compliant to: The IEEE 802.11 Standard on Wireless LANs(Revision A/B), as defined and approved by the Institute of Electrical and Electronics Engineers. The Wireless Fidelity(Wi-Fi) certification as defined by the Wi-Fi Alliance. CAUTION Bluetooth™ and WirelessLAN devices operate within the same radio frequency range and may interfere with one another. If you use …

Text truncated - open the document above for the full version.

This sheet is for information only. The wireless LAN card must be installed by Toshiba or Toshiba OEM dealers. 2. Apply to following Wireless LAN label to position C shown in the figure for the Tecra 9000 or the figure for the Portégé 4000. Apply this Label

Toshiba Corporation FCC ID: CJ6UPA3234WL Request for limited modular approval Transmitter Module Characteristics Item Requirements EUT 1 Have its own RF shielding Device is equipped with Metal shielding to cover RF section. Refer to external photos 2 Have buffered modulation/data inputs (if such inputs are provided), All inputs to the modules are buffered through logic or microprocessor inputs. 3 Have it own power supply regulation Internal 1.8V power regulator. Refer to Block diagram 4 Meet the antenna requirements of Section 15.203 Device is equipped with unique antenna ( u.FL(v)- LP-040) connector. Refer to external photos 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Device was tested inside the laptop for limited modular approval. Refer to setup photos. 6 Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. Two proposed FCC ID label format are included in the filing. One of label is to be placed on the module and the other label is to be placed on the outside of system. Refer to FCC ID label format and location file. 7 The modular transmitter is manufactured so that the user cannot influence the operation of the transmitter that will operate outside of the scope of the regulations. Refer to “User’s Guide” Exhibit 8 Address compliance with the Commission's RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4). 20cm Separation distance will be maintained for mobile application.

Bottom side view Regulatory Label Regulatory Label of Wireless LAN on bottom of PC

Toshiba FCC ID:CJ6UPA3234WL ( WLAN ) and FCC ID:CJ6UPA3232BT ( Bluetooth ) Antenna location

FCC CFR47 PART 15 SUBPART C TEST REPORT FOR 802.11a/b MINIPCI TYPE 3B CARD MODEL NUMBER: PA3234U-1MPC, PA3267U-1MPC FCC ID: CJ6UPA3234WL REPORT NUMBER: 03U2054-1 ISSUE DATE: 6/30/2003 Prepared for TOSHIBA CORPORATION DIGITAL MEDIA NETWORK COMPANY 2-9 SUEHIRO-CHO, OME TOKYO, 198-8710 JAPAN Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 2 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION................................................................................................. 3 2. DESCRIPTION OF EUT.................................................................................................................... 4 3. TEST METHODOLOGY.................................................................................................................. 5 4. FACILITIES AND ACCREDITATION.......................................................................................... 5 4.1. FACILITIES AND EQUIPMENT................................................................................................. 5 4.2. TABLE OF ACCREDITATIONS AND LISTINGS........................................................................ 6 5. CALIBRATION AND UNCERTAINTY......................................................................................... 7 5.1. MEASURING INSTRUMENT CALIBRATION............................................................................ 7 5.2. MEASUREMENT UNCERTAINTY.............................................................................................. 7 5.3. TEST AND MEASUREMENT EQUIPMENT............................................................................... 8 6. SETUP OF EQUIPMENT UNDER TEST....................................................................................... 9 7. APPLICABLE LIMITS AND TEST RESULTS........................................................................... 13 7.1. RADIATED EMISSIONS............................................................................................................ 13 7.2. CO-LOCATED RADIATED EMISSIONS.................................................................................. 28 7.3. POWERLINE CONDUCTED EMISSIONS................................................................................ 34 8. SETUP PHOTOS.............................................................................................................................. 38 REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 3 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. TEST RESULT CERTIFICATION COMPANY NAME: TOSHIBA CORPORATION DIGITAL MEDIA NETWORK COMPANY 2-9 SUEHIRO-CHO, OME TOKYO, 198-8710, JAPAN EUT DESCRIPTION: 802.11a/b MINIPCI TYPE 3B CARD MODEL: PA3234U-1MPC, PA3267-1MPC MODEL DIFFERENCE: THE ONLY DIFFERENCE IS THE END-USE APPLICATION OF THE MODULE. DATE TESTED: 6/12 – 6/15/2003 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. Note: The 2.4 GHz band is applicable to this report; the 5.2 GHz band of operation is documented in a separate report. Conducted measurement is documented in separate report. Approved & Released For CCS By: Tested By: MIKE HECKROTTE NEELESH RAJ CHIEF ENGINEER EMC ENGINEER COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 4 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 2. DESCRIPTION OF EUT The EUT is an 802.11a/b Mini PCI Type 3B Card operating in the 2400 – 2483.5 MHz band with a peak output power of 16.53dBm (45mW) has a peak antenna gain of 4.8dBi. The changes are as follows: Add a new host Toshiba computer model PP4012-624F and add three new film antennas. 1. Hitachi Cable, Dual Band Film antenna, model: HTL008, antenna gain 4.8dBi. 2. Hitachi Cable, Wide band film antenna, model: HTL012, antenna gain 4.1dBi. 3. Tyco Electronics AMP, Dual band film antenna, TIAN01, antenna gain 1.0dBi. Testing was performed on the worst-case, highest gain antenna since all three antennas are the sam…

Text truncated - open the document above for the full version.

File: R51032 Page 1 of 17 Electromagnetic Emissions Test Report and Application for Grant of Equipment Authorization pursuant to FCC Part 15, Subpart C Specifications for an Intentional Radiator on the Intel Corporation Model: WM3B2100A FCC ID: PD9WM3B2100A GRANTEE: Intel Corporation 2300 Corporate Center Drive Thousand Oaks, CA 91320 TEST SITE: Elliott Laboratories, Inc. 684 W. Maude Avenue Sunnyvale, CA 94086 REPORT DATE: April 29, 2003 FINAL TEST DATE: April 23 and April 24, 2003 AUTHORIZED SIGNATORY: ______________________________ Juan Martinez Sr. EMC Engineer Elliott Laboratories, Inc. is accredited by the A2LA, certificate number 2016-01, to perform the test(s) listed in this report. This report shall not be reproduced, except in its entirety, without the written approval of Elliott Laboratories, Inc. Elliott Laboratories, Inc. -- EMC Department Test Report Report Date: April 29, 2003 File: R51032 Page 2 of 17 Pages TABLE OF CONTENTS COVER PAGE...................................................................................................................................................................................1 APPLICATION AND AGREEMENT FOR CERTIFICATION SERVICES.........................................................................1 TABLE OF CONTENTS..............................................................................................................................................................2 DECLARATIONS OF COMPLIANCE......................................................................................................................................3 SCOPE............................................................................................................................................................................................4 OBJECTIVE...................................................................................................................................................................................4 STATEMENT OF COMPLIANCE..............................................................................................................................................4 SUMMARY OF RESULTS...........................................................................................................................................................5 MEASUREMENT UNCERTAINTIES....................................................................................................................................6 EQUIPMENT UNDER TEST (EUT) DETAILS..........................................................................................................................7 GENERAL...................................................................................................................................................................................7 OTHER EUT DETAILS.............................................................................................................................................................7 ENCLOSURE..............................................................................................................................................................................7 MODIFICATIONS.....................................................................................................................................................................7 SUPPORT EQUIPMENT...........................................................................................................................................................7 EUT INTERFACE PORTS........................................................................................................................................................8 EUT OPERATION DURING TESTING...................................................................................................................................8 TEST SITE......................................................................................................................................................................................9 GENERAL INFORMATION.....................................................................................................................................................9 CONDUCTED EMISSIONS CONSIDERATIONS.................................................................................................................9 RADIATED EMISSIONS CONSIDERATIONS....................................................................................................................9 MEASUREMENT INSTRUMENTATION................................................................................................................................10 INSTRUMENT CONTROL COMPUTER.............................................................................................................................10 LINE IMPEDANCE STABILIZATION NETWORK (LISN)..............................................................................................10 POWER METER......................................................................................................................................................................11 FILTERS/ATTENUATORS....................................................................................................................................................11 ANTENNAS.............................................................................................................................................................................11 ANTENNA MAST AND EQUIPMENT TURNTABLE.....................................................................................................11 INSTRUMENT CALIBRATION............................................................................................................................................11 TEST PROCEDURES.........................................................................................................................................…

Text truncated - open the document above for the full version.

REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 38 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8. SETUP PHOTOS RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 39 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED BACK PHOTO REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 40 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE RADIATED EMISSIONS SETUP DIGITAL DEVICE FRONT PHOTO REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 41 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE BACK PHOTO REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 42 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 03U2054-1 DATE: 6/30/2003 EUT: 802.11a/b MINIPCI TYPE 3B CARD FCC ID:CJ6UPA3234WL Page 43 of 43 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. END OF REPORT LINE CONDUCTED BACK PHOTO