CKEJHS-180AIS

Automatic Identification System Model JHS-180 Operation Manual (Field Maintenance) 2 CONTENTS 1.Field Maintenance mode 1.1 Turning On the power for Field Maintenance mode 1.2 Menu Tree of Field Maintenance mode 2. FIELD MAINTENANCE 2.1 SELF TEST 2.2 COMM STATUS 2.3 REPORTING RATE 2.4 SELF TEST LOG 2.5 RANGE ALARM LOG 2.6 PORT LOG 2.7 PORT OPTION 2.8 TRX CHECK 2.9 SOFTWARE VER UP 3. INITIALIZE 3.1 SENSOR SETTING 3.2 INT. GPS SETTING 3.3 SHIP STATIC DATA 3.4 TRANSPONDER INIT 3.5 ANTENNA SELECTION 3 1.Field Maintenance Mode 1.1 Turning On the power for Field Maintenance mode JHS-180 can operate “Field Maintenance Mode” for installation and maintenance. To operate “Field Maintenance Mode”, JHS-180 needs special operation in turning the power on. The special operation is; When turn the power on, pressing and holding [PWR] and [MENU] until starting display “AIS CONTROLLER NOW LOADING ---” appears . In “Field Maintenance Mode” operation, - The transponder doesn’t operate automatically TDMA transmission. - Two menu item are added to the “Main Menu”. “Main Menu” in Field Maintenance Mode operation 1.2 Menu Tree of Field Maintenance mode (Power On:[MENU]+[PWR]) Select(1) key (Power On)[▲]/[▼],[ENT] Other Ships List [0]-[9] or [▲]/[▼],[ENT][0]-[9] or [▲]/[▼],[ENT][0]-[9] or [▲]/[▼],[ENT] [MENU] [MENU]key 3.MAIN MENU1.MESSAGE1.EDIT AND TXDestination address Message type Message editing Transmission 2.TX TRAYTransmitted Message reading 3.RX TRAYReceived Message reading 4.INTERROGATIONAddress,Req.Info., Tx and Ack 5.LONG RANGE Received Long Range Message 2.DESTINATION1.DESTINATION 2.WAYPOINT TEXT 3.ETA 4.WAYPOINT 3.NAVIGATION1.NAVIGATIONAL STATUS 2.PERSONS ON-BOARD 3.TYPE OF SHIP 4.CARGO TYPE 5.DRAUGHT 6.HEIGHT OVER KEEL 4.ALARM SETTING1.RANGE 2.LOST TARGET 5.GROUP SHIPRegistration, Deletion 6.SET UP1.PASSWORDPassword changing 2.CH MANAGEMENT 3.OWN SHIP DATA 4.LONG RANGE RESPONSE 5.CONTRAST 6.NUMBER OF RETRIES 7.MAINTENANCE1.TRX CONDITION 2.AIS ALARM 3.SENSOR STATUS User Menu4.POWER ON/OFF LOG 5.TX ON/OFF LOG 6.SOFTWARE VERSION 8.FIELD MAINTENANCE 1.SELF TEST 2.COMM STATUS Field Maintenance Menu 3.REPORTING RATE 4.SELF TEST LOG 5.RANGE ALARM LOG 6.PORT LOGEach port sentence log 7.PORT OPTION 8.TRX ADJUST 9.SOFTWARE VERSION UP Transponder version up, Controller version up 0.CONTROLLER INITIALIZE 9.INITIALIZE1.SENSOR SETTING 1.SENSOR1 (Sentence Select, Baudrate,Parity bit) 2.SENSOR2 (Sentence Select, Baudrate,Parity bit) 3.SENSOR3 (Sentence Select, Baudrate,Parity bit) 4.SENSOR4 (Sentence Select, Baudrate,Parity bit) 5.SENSOR5 (Sentence Select, Baudrate,Parity bit) 2.INTERNAL GPS SETTING1.INT. GPS POSITION 2.ANTENNA HEIGHT 3.ROUGHLY POSITION 4.UTC 5.TIME DIFFERENCE 3.SHIP STATIC DATA SETTING 1.SHIP NAME 2.MMSI NUMBER 3.IMO NUMBER 4.CALL SIGN 5.GPS ANT. POSITION 6.SENSOR TYPE 4.TRANSPONDER INITIALIZE 5.ANTENNA SELECTION Other Ship's detail Information 5 2. FIELD MAINTENANCE “FIELD MAINTENANCE” menu is displayed by pressing 8 key in the “Main Menu”. Display of “FIELD MAINTENACE” 6 2.1 SELF TEST “SELF TEST” menu is displayed by pressing 1 key in the “FIELD MAINTENANCE” menu. Display of “SELF TEST” (All result is OK) Display of “SELF TEST” (All result is fault) Display of “SELF TEST” (Time out) 7 Indication of failures in NTE-180 AIS Transponder Control unitIndicationTRX unitIndication CPU(FLASH ROM)FROMPAPA CPU(SRAM)SRAMTemperatureTEMP Ext. FLASH ROMEFROMForward powerVF Serial Communication Access SCAReverse powerVR Serial I/OSIO Digital Up ConverterDUC GPS receiverGPS GPS InformationGPS-INFO 8 2.2 COMM STATUS “COMM STATUS” menu is displayed by pressing 2 key in the “FIELD MAINTENANCE” menu. Display of “COMM STAUS” 9 2.3 REPORTING RATE “REPORTING RATE” menu is displayed by pressing 3 key in the “FIELD MAINTENANCE” menu. Display of “REPORTING RATE” 10 2.4 SELF TEST LOG “SELF TEST LOG” menu is displayed by pressing 4 key in the “FIELD MAINTENANCE” menu. Display of “SELF TEST LOG” 11 2.5 RANGE ALARM LOG “RANGE ALARM LOG” menu is displayed by pressing 5 key in the “FIELD MAINTENANCE” menu. Display of “RANGE ALARM LOG” 12 2.6 PORT LOG “PORT LOG” menu is displayed by pressing 6 key in the “FIELD MAINTENANCE” menu. Display of “PORT LOG” Details of each port is displayed by pressing from 1 to 1 1 key in the “PORT LOG” menu. Display of “SENSOR1 LOG” 13 2.7 PORT OPTION “PORT OPTION” menu is displayed by pressing 7 key in the “FIELD MAINTENANCE” menu. Display of “PORT OPTION” 14 2.8 TRX CHECK “TRX CHECK” menu is displayed by pressing 8 key in the “FIELD MAINTENANCE” menu. Display of “TRX CHECK” “RX CHANNEL CHECK” menu is displayed by pressing 1 key in the “TRX CHECK” menu. Display of “RX CHANNEL CHECK” 15 “TX POWER CHECK” menu is displayed by pressing 2 key in the “TRX CHECK” menu. Display of “TX POWER CHECK” “TX POWER ADJUS” menu is displayed by pressing 3 key in the “TRX CHECK” menu. Display of “TX POWER ADJUST” 16 2.9 SOFTWARE VER UP “SOFWARE VER UP” menu is displayed by pressing 9 key in the “FIELD MAINTENANCE” menu. Display of “SOFTWARE VER UP” Display of transponder version up in “SOFTWARE VERSION UP” 17 Display of controller version up in “SOFTWARE VERSION UP” 18 2.10 STATE INITIALIZE “STATE INITIALIZE” is displayed by pressing 0 key in the “FIELD MAINTENANCE” menu. Display of “STATE INITIALIZE”(OFF) Display of “STATE INITIALIZE”(ON) 19 3. INITIALIZE “INITIALIZE” menu is displayed by pressing 9 key in the “Main Menu”. Display of “INITIALIZE” 20 3.1 SENSOR SETTING “SENSOR SETTING” menu is displayed by pressing 1 key in the “INITIALIZE” menu. Display of “SENSOR SETTING” Each sensor filter menu is displayed by pressing from 1 to 5 key in the “SENSOR SETTING” menu. Display of each sensor filter setting in “SENSOR SETTING” 21 3.2 INT. GPS SETTING “INT. GPS SETTING” menu is displayed by pressing 2 key in the “INITIALIZE” menu. Display of “INT. GPS SETTING” 22 3.3 SHIP STATIC DATA “SHIP STATIC DATA” menu is displayed by pressing 3 key in the “INITIALIZE” menu. Display of “SHIP STATIC DATA” 23 3.4 TRANSPONDER INIT “T…

Text truncated - open the document above for the full version.

NBD-577A POWER SUPPY UNIT NTE-180 AIS TRANSPONDER NQD-4190 JUNCTION BOX JHS-180 AISSYSTEM BLOCK DIAGRAM NCM-722 AIS CONTROLLER Gyro Compass CONNECT1CONNECT2 (D)GPS Receiver DC24V IN CONNECT1 CONNECT2 IEC61162-2, DC24V IEC61162-1/2 AC100/220V ( 200VA) INPUT OUTPUT GND GND DC24V OUT DC 24V AUX1 NSK SENSOR1SENSOR2 SENSOR3 MAINTE ALARM1 SENSOR4 SENSOR5 AUX2 LONGRANGE DIFF ALARM2 TRANSPONDER NMEA 2000 DC24V (20V - 31.2V) DC24V DC24V (5A) (20V - 31.2V) 2002/07/05 (OPTION) IEC61162-1/2 GND Doppler Speed Log IEC61162-1/2 ROT Indicator IEC61162-1/2 ECDIS/RADAR IEC61162-1/2 ECDIS/RADAR IEC61162-1/2 Above Deck Below Deck NQE-3111 CONNECTION BOX 1 2 3 4 5 6 7 8 9 10 CONNECT 1 7ZCAF0079 5m (ATTACHMENT) NCM-722 AIS CONTROLLER 7ZCJD0095 5m (ATTACHMENT) (DOCK SUPPLY) CONNECT 2CONNECT 2 CONNECT 1 GND DC24V DC24V OUT 7ZCAF0078 5m (ATTACHMENT) D-SUB 37pin Female D-SUB 25pin Female D-SUB 37pin Male D-SUB 25pin Male NBD-577A POWER SUPPLY UNIT SENSOR1 Rx-A SENSOR1 Rx-B TRANSPONDER Rx-B TRANSPONDER Rx-A TRANSPONDER Tx-B TRANSPONDER Tx-A TRANSPONDER 24V- GND GND TRANSPONDER 24V- TRANSPONDER 24V- TRANSPONDER 24V- TRANSPONDER 24V+ TRANSPONDER 24V+ TRANSPONDER 24V+ TRANSPONDER 24V+ GND-ISO GND-SHIELD SENSOR2 Rx-A SENSOR2 Rx-B GND-ISO GND-SHIELD SENSOR3 Rx-A SENSOR3 Rx-B GND-ISO GND-SHIELD SENSOR4 Rx-A SENSOR4 Rx-B GND-ISO GND-SHIELD NTE-180 AIS TRANSPONDER (ATTACHED CABLE) NQD-4190 JUNCTION BOX COPPER SHEET (ATTACHMENT) TRANSPONDER Rx-B (BLUE) TRANSPONDER Rx-A (ORANGE) TRANSPONDER Tx-B (GREEN) TRANSPONDER Tx-A (YELLOW) 24V- (BLACK) 24V- (BLACK) 24V+ (RED) 24V+ (RED) GND-SHIELD (GRAY) 0.75mm 2 7pairs (JIS TTYCYS-7) 50m max (DOCK SUPPLY) TRANSPONDER 24V+ TRANSPONDER 24V+ TRANSPONDER 24V+ TRANSPONDER 24V- TRANSPONDER 24V- TRANSPONDER 24V- TRANSPONDER 24V- TRANSPONDER Tx-A TRANSPONDER Tx-B TRANSPONDER Rx-A TRANSPONDER Rx-B GND BELOW DECK ABOVE DECK 2 0.75mm 2 (JIS TTYCS-1) (DOCK SUPPLY) GYRO COMPASS DOPPLER SPEED LOG ROT INDICATOR (D)GPS RECEIVER 2 0.75mm 2 (JIS TTYCS-1) (DOCK SUPPLY) 2 0.75mm 2 (JIS TTYCS-1) (DOCK SUPPLY) 2 0.75mm 2 (JIS TTYCS-1) (DOCK SUPPLY) JHS-180 AISINTERCONNECTION DIAGRAM AC IN + - DC IN (DOCK SUPPLY) GND REMOTE CONT + - AC100/ 220V (BACKUP POWER SUPPLY) DC24V 2 x 2.5mm 2 (JIS DPYC(S)-2.5) DC24V OUT +- +- E + - DC24V IN E + - 2 x 2.5mm 2 (JIS DPYC(S)-2.5) (DOCK SUPPLY) (DOCK SUPPLY) 2 x 2.5mm 2 (JIS DPYC(S)-2.5) (DOCK SUPPLY) 0.75mm 2 X4pairs (JIS TTYCS-4) (DOCK SUPPLY) ECDIS/RADAR 0.75mm 2 X4pairs (JIS TTYCS-4) (DOCK SUPPLY) NQE-3111 CONNECTION BOX DC24V OUT 2002/07/05 (DOCK SUPPLY) GND ALARM 1A ALARM 1C ALARM 1B SENSOR5 Rx-A SENSOR5 Rx-B GND-ISO GND-SHIELD ALARM 2A ALARM 2C ALARM 2B GND-SHIELD GND-ISO AUX1 Tx-A AUX1 Tx-B AUX1 Rx-A AUX1 Rx-B GND-ISO GND-ISO AUX2 Tx-A AUX2 Tx-B AUX2 Rx-A AUX2 Rx-B GND-ISO ECDIS/RADAR GND-SHIELD TRANSPONDER 24V+

Dear Mr. Leimer, Attached you will find four pdf files that contain the entire TUV test report. Unfortunately, the numbering on the pdf file does not match the actual page number, however, the page number is clearly marked on each page of the test report. If you have any problems or questions regarding this or any other matter, please do not hesitate to contact me. With Best Regards, Eric D’Ancicco High Seas Service Coordinator [email protected] 206-654-5644 XT 202 206-654-5697 FAX

Table of Components for AIS Model JHS-180 Quantity No.NameType Per setTotal Remarks 1.Standard Components 1.1AIS TransponderNTE-18011 With whip antenna, 2m connection cable, and fitting bands 1.2Junction BoxNQD-419011 1.3AIS ControllerNCM-72211 1.4Connection BoxNQE-311111 1.5Power Supply Cable7ZCJD009511Length=5m 1.6Control Cable 17ZCAF007811Length=5m 1.7Control Cable 27ZCAF007911Length=5m 1.8Power Supply UnitNBD-577A11 1.9Spare Parts7ZXJD002711 2.Options 2.1Console Mounting Kit MPBP30837 1 For NCM-722 Color: 2.5G7/2 2.2Console Mounting Kit MPBP30838 1 For NCM-722 Color: 7.5BG7/2 1. Components 1. Components

FCC ID: CKEJHS-180 Date: March 12, 2003 Federal Communications Commission Via Electronic Filing Attention: Authorization & Evaluation Division Applicant: Japan Radio Co., Ltd. Equipment: JHS-180 FCC ID: CKEJHS-180 FCC Rules: 80 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cva MFA p0330002, d0330021 FCC ID: CKEJHS-180 LIST OF EXHIBITS (FCC CERTIFICATION (TRANSMITTERS) - REVISED 9/28/98) APPLICANT: Japan Radio Co., Ltd. FCC ID: CKEJHS-180 BY APPLICANT: 1. LETTER OF AUTHORIZATION x 2. IDENTIFICATION DRAWINGS, 2.1033(c)(11) x LABEL x LOCATION OF LABEL x COMPLIANCE STATEMENT x LOCATION OF COMPLIANCE STATEMENT 3. PHOTOGRAPHS, 2.1033(c)(12) x 4. DOCUMENTATION: 2.1033(c) (3) USER MANUAL x (9) TUNE-UP/ALIGNMENT PROCEDURE x (10) SCHEMATIC DIAGRAM x (10) OPERATIONAL DESCRIPTION x BLOCK DIAGRAM x PARTS LIST x 5. MPE REPORT x BY M.F.A. INC. A. TESTIMONIAL & STATEMENT OF CERTIFICATION B. STATEMENT OF QUALIFICATIONS MFA p0330002, d0330021 FCC ID: CKEJHS-180 T R A N S M I T T E R C E R T I F I C A T I O N of FCC ID: CKEJHS-180 MODEL: JHS-180 to FEDERAL COMMUNICATIONS COMMISSION Rule Part(s) 80 DATE OF REPORT: March 12, 2003 ON THE BEHALF OF THE APPLICANT: Japan Radio Co., Ltd. AT THE REQUEST OF : P.O. FLOM0001 Japan Radio Co. Ltd Seattle Branch 1011 SW Klickitat Way Bldg. B, Suite 100 Seattle, WA 98134 Attention of: Shunichi Hasama, General Manager (206) 654-5644; FAX: -7030 Eric D'Ancicco, High Seas Product Support [email protected] SUPERVISED BY: Morton Flom, P. Eng. MFA p0330002, d0330021 FCC ID: CKEJHS-180 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. MFA p0330002, d0330021 FCC ID: CKEJHS-180 TABLE OF CONTENTS RULE DESCRIPTION PAGE . Test Report 1 2.1033(c) General Information Required 2 2.1033(c)(14) Rule Summary 5 . Standard Test Conditions and Engineering Practices 6 2.1046(a), 80.215 R.F. Power Output 7 2.1051, 80.211(d) & (f) Spurious Emissions at Antenna Terminals) 8 2.1053(a) Field Strength of Spurious Radiation 13 2.1046(a) ERP Carrier Power (Radiated) 14 2.1049(c)(1), 80.211(d) Emission Masks (Occupied Bandwidth) 15 2.1047(b) Modulation Limiting 25 2.1047(a) Audio Frequency Response 26 2.1047(a) Audio Low Pass Filter (Voice Input) 27 2.1055(a)(1) Frequency Stability (Temperature Variation) 28 2.1055(b)(1) Frequency Stability (Voltage Variation) 29 80.225 Requirements for DSC 30 2.202(g) Necessary Bandwidth and Emission Bandwidth 31 MFA p0330002, d0330021 FCC ID: CKEJHS-180 PAGE NO. 1 of 31. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d0330021 d) Client: Japan Radio Co. Ltd Seattle Branch 1011 SW Klickitat Way Bldg. B, Suite 100 Seattle, WA 98134 e) Identification: JHS-180 FCC ID: CKEJHS-180 Description: Automatic Identification System "AIS" (Transponder) f) EUT Condition: Not required unless specified in individual tests. g) Report Date: March 12, 2003 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. MFA p0330002, d0330021 FCC ID: CKEJHS-180 PAGE NO. 2 of 31. LIST OF GENERAL INFORMATION REQUIRED FOR CERTIFICATION IN ACCORDANCE WITH FCC RULES AND REGULATIONS, VOLUME II, PART 2 AND TO 80 Sub-part 2.1033 (c)(1): NAME AND ADDRESS OF APPLICANT: Japan Radio Co., Ltd. Nittochi Nishi-Shinjyuku 10-1 Nishi-Shinjyuku 6 chome Shinjyuku-ku 160-0023 Japan MANUFACTURER: Applicant (c)(2): FCC ID: CKEJHS-180 MODEL NO: JHS-180 (c)(3): INSTRUCTION MANUAL(S): PLEASE SEE ATTACHED EXHIBITS (c)(4): TYPE OF EMISSION: 16K0G1D, 12K5G2B (c)(5): FREQUENCY RANGE, MHz : 156 to 163 (c)(6): POWER RATING, Wat…

Text truncated - open the document above for the full version.