CKENCR-330Marine

NCR-330 NAVTEX RECEIVER INSTRUCTION MANUAL i PREFACE Thank you for purchasing the NCR-330 JRC NAVTEX Receiver. The NAVTEX receiver automatically receives and prints out NAVTEX service broadcasts supplied in English. •Before using the receiver, carefully read this INSTRUCTION MANUAL so as to fully understand the proper usage and handling. •Keep the INSTRUCTION MANUAL in an appropriate place so that you can readily refer to it when necessary. •If you are uncertain about any operations of the receiver or encounter any problems during operation, refer to this manual. You will find solutions to common problems and useful hints and suggestions. ii BEFORE OPERATION Alert Symbols A number of alert symbols are used in this manual and labeled on the product itself to ensure safe and proper usage, and to prevent possible injury to you or others and to avoid possible property damage during operation or maintenance. Some of these alert symbols and their meanings are shown below. Before reading the remainder of this manual, familiarize yourself with the following symbols and messages: WARNING Indicates a situation that could result in death or serious personal injury if ignored or if the product is mishandled. CAUTION Indicates a situation that could result in personal injury and/or property damage if ignored or if the product is mishandled. Examples of alert symbols The triangular symbol (∆) means “caution” (danger and/or other warning). The specific type of hazard (not specified in this example) is depicted in the warning box. This symbol signifies an action that is prohibited. The specific type of prohibited action (in this example, disassembly) is depicted in or near the symbol. This symbol signifies a required action. The specific type of required action (in this example, removing the power plug from the outlet) is depicted in the symbol. iii OPERATING PRECAUTIONS WARNING Do not place heavy objects on the receiver unit. Failure to observe this warning could result in the unit becoming unbalanced and thus causing injury if it falls. Do not place heavy objects on the power cable or the antenna cable. Failure to observe this warning could result in fire, electrical shock, product trouble, and/or receiver signal deterioration. Do not operate at voltages other than 10.8 - 35.0 VDC. Failure to observe this warning could result in fire, electrical shock, and/or malfunction. If an unusual smell, smoke, or other abnormality is detected, immediately turn off the power to the unit and then turn off the power on the power distribution panel of the vessel. After confirming that the unusual smell, smoke, or other abnormality has cleared up, consult your dealer or nearest JRC service/sales representative for repair. Continued use while the abnormality persists may cause fire and/or electrical shock. iv OPERATING PRECAUTIONS CAUTION Do not place the receiver unit on an unstable surface. If placed on an unstable table or an uneven surface, it could fall and result in personal injury and/or damage or malfunction of the unit. Secure the unit sturdily using the supplied screws. Do not expose to water or moisture. Placement on exposed decks or in humid places may cause electrical shock or product malfunction. Do not open or remove the cover of the unit. Touching the parts inside could result in electrical shock. If it is absolutely necessary to check the interior of the unit for maintenance purposes, turn off the power switch on the power distribution panel supplying its power. Avoid exposure to direct sunlight, heat, moisture, and dust. Failure to do so may cause fire, malfunction, and/or deterioration of print-out quality. Always use the JRC-recommended printer paper. The use of any other paper may cause printer trouble and/or deterioration of print-out quality. When cleaning, do not use benzene, alcohol, thinner, or other volatile solvents. These solvents may damage or cause deterioration to the coated surface. Wipe the surface lightly with a soft cloth. v AFTER UNPACKING After unpacking, make sure that the following components and accessories are all present. If any components or accessories are missing, please contact your dealer or the nearest JRC sales representative in your area: NCR-330 NAVTEX Receiver ComponentModel/Part NumberQuantity NAVTEX receiver unitNCR-3301 Mounting screwsMPTG020244 Printer paperH-7ZPJD00441 Instruction manualH-7ZPJD00671 Operating cardH-7ZPJD00691 Spare fuseH-6ZXAF000211 Ship Registration FormH-7ZPJD00651 NAW-330 NAVTEX Antenna ComponentModel/Part NumberQuantity Antenna couplerNAW-3301 Whip antennaCODE3151 Plain washerBRTG004041 Spring lock washerBRTG004021 SpacerMTV0024731 Fitting bandsMPBP302742 Self bonding tape96451 AFTER INSTALLATION After completing the installation, please fill out the enclosed Ship Registration Form and return it to the following address by facsimile: Marine Service Department, Japan Radio Co., Ltd. 17-8, Osaki 1-chome, Shinagawa-ku, Tokyo, JAPAN 141-0032 Facsimile No. +81-33-492-2777 vi EXTERNAL VIEW OF EQUIPMENT vii CONTENTS PAGE PREFACE..........................................................................................................................................i BEFORE OPERATION.....................................................................................................................ii OPERATING PRECAUTIONS.........................................................................................................iii AFTER UNPACKING........................................................................................................................v EQUIPMENT APPEARANCE..........................................................................................................vi GLOSSARY .....................................................................................................................................x CHAPTER 1 EQUIPMENT OVERVIEW SECTION 1.1FUNCTIONS........................................................................…

Text truncated - open the document above for the full version.

NCR-330 NAVTEX RECEIVER INSTRUCTION MANUAL i PREFACE Thank you for purchasing the NCR-330 JRC NAVTEX Receiver. The NAVTEX receiver automatically receives and prints out NAVTEX service broadcasts supplied in English. •Before using the receiver, carefully read this INSTRUCTION MANUAL so as to fully understand the proper usage and handling. •Keep the INSTRUCTION MANUAL in an appropriate place so that you can readily refer to it when necessary. •If you are uncertain about any operations of the receiver or encounter any problems during operation, refer to this manual. You will find solutions to common problems and useful hints and suggestions. ii BEFORE OPERATION Alert Symbols A number of alert symbols are used in this manual and labeled on the product itself to ensure safe and proper usage, and to prevent possible injury to you or others and to avoid possible property damage during operation or maintenance. Some of these alert symbols and their meanings are shown below. Before reading the remainder of this manual, familiarize yourself with the following symbols and messages: WARNING Indicates a situation that could result in death or serious personal injury if ignored or if the product is mishandled. CAUTION Indicates a situation that could result in personal injury and/or property damage if ignored or if the product is mishandled. Examples of alert symbols The triangular symbol (∆) means “caution” (danger and/or other warning). The specific type of hazard (not specified in this example) is depicted in the warning box. This symbol signifies an action that is prohibited. The specific type of prohibited action (in this example, disassembly) is depicted in or near the symbol. This symbol signifies a required action. The specific type of required action (in this example, removing the power plug from the outlet) is depicted in the symbol. iii OPERATING PRECAUTIONS WARNING Do not place heavy objects on the receiver unit. Failure to observe this warning could result in the unit becoming unbalanced and thus causing injury if it falls. Do not place heavy objects on the power cable or the antenna cable. Failure to observe this warning could result in fire, electrical shock, product trouble, and/or receiver signal deterioration. Do not operate at voltages other than 10.8 - 35.0 VDC. Failure to observe this warning could result in fire, electrical shock, and/or malfunction. If an unusual smell, smoke, or other abnormality is detected, immediately turn off the power to the unit and then turn off the power on the power distribution panel of the vessel. After confirming that the unusual smell, smoke, or other abnormality has cleared up, consult your dealer or nearest JRC service/sales representative for repair. Continued use while the abnormality persists may cause fire and/or electrical shock. iv OPERATING PRECAUTIONS CAUTION Do not place the receiver unit on an unstable surface. If placed on an unstable table or an uneven surface, it could fall and result in personal injury and/or damage or malfunction of the unit. Secure the unit sturdily using the supplied screws. Do not expose to water or moisture. Placement on exposed decks or in humid places may cause electrical shock or product malfunction. Do not open or remove the cover of the unit. Touching the parts inside could result in electrical shock. If it is absolutely necessary to check the interior of the unit for maintenance purposes, turn off the power switch on the power distribution panel supplying its power. Avoid exposure to direct sunlight, heat, moisture, and dust. Failure to do so may cause fire, malfunction, and/or deterioration of print-out quality. Always use the JRC-recommended printer paper. The use of any other paper may cause printer trouble and/or deterioration of print-out quality. When cleaning, do not use benzene, alcohol, thinner, or other volatile solvents. These solvents may damage or cause deterioration to the coated surface. Wipe the surface lightly with a soft cloth. v AFTER UNPACKING After unpacking, make sure that the following components and accessories are all present. If any components or accessories are missing, please contact your dealer or the nearest JRC sales representative in your area: NCR-330 NAVTEX Receiver ComponentModel/Part NumberQuantity NAVTEX receiver unitNCR-3301 Mounting screwsMPTG020244 Printer paperH-7ZPJD00441 Instruction manualH-7ZPJD00671 Operating cardH-7ZPJD00691 Spare fuseH-6ZXAF000211 Ship Registration FormH-7ZPJD00651 NAW-330 NAVTEX Antenna ComponentModel/Part NumberQuantity Antenna couplerNAW-3301 Whip antennaCODE3151 Plain washerBRTG004041 Spring lock washerBRTG004021 SpacerMTV0024731 Fitting bandsMPBP302742 Self bonding tape96451 AFTER INSTALLATION After completing the installation, please fill out the enclosed Ship Registration Form and return it to the following address by facsimile: Marine Service Department, Japan Radio Co., Ltd. 17-8, Osaki 1-chome, Shinagawa-ku, Tokyo, JAPAN 141-0032 Facsimile No. +81-33-492-2777 vi EXTERNAL VIEW OF EQUIPMENT vii CONTENTS PAGE PREFACE..........................................................................................................................................i BEFORE OPERATION.....................................................................................................................ii OPERATING PRECAUTIONS.........................................................................................................iii AFTER UNPACKING........................................................................................................................v EQUIPMENT APPEARANCE..........................................................................................................vi GLOSSARY .....................................................................................................................................x CHAPTER 1 EQUIPMENT OVERVIEW SECTION 1.1FUNCTIONS........................................................................…

Text truncated - open the document above for the full version.

NCR-330 NAVTEX RECEIVER INSTRUCTION MANUAL i PREFACE Thank you for purchasing the NCR-330 JRC NAVTEX Receiver. The NAVTEX receiver automatically receives and prints out NAVTEX service broadcasts supplied in English. •Before using the receiver, carefully read this INSTRUCTION MANUAL so as to fully understand the proper usage and handling. •Keep the INSTRUCTION MANUAL in an appropriate place so that you can readily refer to it when necessary. •If you are uncertain about any operations of the receiver or encounter any problems during operation, refer to this manual. You will find solutions to common problems and useful hints and suggestions. ii BEFORE OPERATION Alert Symbols A number of alert symbols are used in this manual and labeled on the product itself to ensure safe and proper usage, and to prevent possible injury to you or others and to avoid possible property damage during operation or maintenance. Some of these alert symbols and their meanings are shown below. Before reading the remainder of this manual, familiarize yourself with the following symbols and messages: WARNING Indicates a situation that could result in death or serious personal injury if ignored or if the product is mishandled. CAUTION Indicates a situation that could result in personal injury and/or property damage if ignored or if the product is mishandled. Examples of alert symbols The triangular symbol (∆) means “caution” (danger and/or other warning). The specific type of hazard (not specified in this example) is depicted in the warning box. This symbol signifies an action that is prohibited. The specific type of prohibited action (in this example, disassembly) is depicted in or near the symbol. This symbol signifies a required action. The specific type of required action (in this example, removing the power plug from the outlet) is depicted in the symbol. iii OPERATING PRECAUTIONS WARNING Do not place heavy objects on the receiver unit. Failure to observe this warning could result in the unit becoming unbalanced and thus causing injury if it falls. Do not place heavy objects on the power cable or the antenna cable. Failure to observe this warning could result in fire, electrical shock, product trouble, and/or receiver signal deterioration. Do not operate at voltages other than 10.8 - 35.0 VDC. Failure to observe this warning could result in fire, electrical shock, and/or malfunction. If an unusual smell, smoke, or other abnormality is detected, immediately turn off the power to the unit and then turn off the power on the power distribution panel of the vessel. After confirming that the unusual smell, smoke, or other abnormality has cleared up, consult your dealer or nearest JRC service/sales representative for repair. Continued use while the abnormality persists may cause fire and/or electrical shock. iv OPERATING PRECAUTIONS CAUTION Do not place the receiver unit on an unstable surface. If placed on an unstable table or an uneven surface, it could fall and result in personal injury and/or damage or malfunction of the unit. Secure the unit sturdily using the supplied screws. Do not expose to water or moisture. Placement on exposed decks or in humid places may cause electrical shock or product malfunction. Do not open or remove the cover of the unit. Touching the parts inside could result in electrical shock. If it is absolutely necessary to check the interior of the unit for maintenance purposes, turn off the power switch on the power distribution panel supplying its power. Avoid exposure to direct sunlight, heat, moisture, and dust. Failure to do so may cause fire, malfunction, and/or deterioration of print-out quality. Always use the JRC-recommended printer paper. The use of any other paper may cause printer trouble and/or deterioration of print-out quality. When cleaning, do not use benzene, alcohol, thinner, or other volatile solvents. These solvents may damage or cause deterioration to the coated surface. Wipe the surface lightly with a soft cloth. v AFTER UNPACKING After unpacking, make sure that the following components and accessories are all present. If any components or accessories are missing, please contact your dealer or the nearest JRC sales representative in your area: NCR-330 NAVTEX Receiver ComponentModel/Part NumberQuantity NAVTEX receiver unitNCR-3301 Mounting screwsMPTG020244 Printer paperH-7ZPJD00441 Instruction manualH-7ZPJD00671 Operating cardH-7ZPJD00691 Spare fuseH-6ZXAF000211 Ship Registration FormH-7ZPJD00651 NAW-330 NAVTEX Antenna ComponentModel/Part NumberQuantity Antenna couplerNAW-3301 Whip antennaCODE3151 Plain washerBRTG004041 Spring lock washerBRTG004021 SpacerMTV0024731 Fitting bandsMPBP302742 Self bonding tape96451 AFTER INSTALLATION After completing the installation, please fill out the enclosed Ship Registration Form and return it to the following address by facsimile: Marine Service Department, Japan Radio Co., Ltd. 17-8, Osaki 1-chome, Shinagawa-ku, Tokyo, JAPAN 141-0032 Facsimile No. +81-33-492-2777 vi EXTERNAL VIEW OF EQUIPMENT vii CONTENTS PAGE PREFACE..........................................................................................................................................i BEFORE OPERATION.....................................................................................................................ii OPERATING PRECAUTIONS.........................................................................................................iii AFTER UNPACKING........................................................................................................................v EQUIPMENT APPEARANCE..........................................................................................................vi GLOSSARY .....................................................................................................................................x CHAPTER 1 EQUIPMENT OVERVIEW SECTION 1.1FUNCTIONS........................................................................…

Text truncated - open the document above for the full version.

Mitaka PlantPhone:(0422)45-9538 No. 5-1-1, Shimorenjyaku Mitaka-shi, Telex:2822-351 Tokyo 181-8510 JapanFax: (0422)45-9957 CERTIFICATE TO:FEDERAL COMMUNICATIONS COMMISSION SUBJECT:TEST DATA FOR TYPE ACCEPTANCE OF NAVTEX RECEIVER FOR THE GMDSS MARITIME MF MOBILE SERVICE FCC ID:CKE NCR-330 Supplier/Manufacturer:Japan Radio Co., Ltd. 5-1-1 Shimorenjyaku, Mitaka City Tokyo 181-8510, Japan This is to certify that model NCR-330 NAVTEX RECEIVER complies with FCC performance standards including IMO resolution A.525 (13) and ITU-R Recommendation 540-2. This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. To the best of my knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standard. Each unit manufactured, imported, or marketed, as defined in the Commission’s regulations, will confirm to the sample(s) tested within the variations that can be expected due to quantity production and testing on a statistical basis. Japan Radio Co., Ltd. E. Kobayashi, Manager, Maritime Communications Section I Engineering Department I Marine Electronics Division TEST RESULT FOR FCC CERTFICATION Purpose of test: Certify NCR-330 Grantee's type or model No.: NCR-330 Drawing, specification or exhibit: FCC Part 2 and 80 Quantity of item tested: One (1) of the above type Abstract: Refer to result sections Date tested completed: January 31, 2000 Tested by T.TAKAHASHI Checked by K.FUJII Approved by E.KOBAYASHI

Mitaka PlantPhone:(0422)45-9538 No. 5-1-1, Shimorenjyaku Mitaka-shi, Telex:2822-351 Tokyo 181-8510 JapanFax: (0422)45-9957 CERTIFICATE TO:FEDERAL COMMUNICATIONS COMMISSION SUBJECT:TEST DATA FOR TYPE ACCEPTANCE OF NAVTEX RECEIVER FOR THE GMDSS MARITIME MF MOBILE SERVICE FCC ID:CKE NCR-330 Supplier/Manufacturer:Japan Radio Co., Ltd. 5-1-1 Shimorenjyaku, Mitaka City Tokyo 181-8510, Japan This is to certify that model NCR-330 NAVTEX RECEIVER complies with FCC performance standards including IMO resolution A.525 (13) and ITU-R Recommendation 540-2. This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. To the best of my knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standard. Each unit manufactured, imported, or marketed, as defined in the Commission’s regulations, will confirm to the sample(s) tested within the variations that can be expected due to quantity production and testing on a statistical basis. Japan Radio Co., Ltd. E. Kobayashi, Manager, Maritime Communications Section I Engineering Department I Marine Electronics Division TEST RESULT FOR FCC CERTFICATION Purpose of test: Certify NCR-330 Grantee's type or model No.: NCR-330 Drawing, specification or exhibit: FCC Part 2 and 80 Quantity of item tested: One (1) of the above type Abstract: Refer to result sections Date tested completed: January 31, 2000 Tested by T.TAKAHASHI Checked by K.FUJII Approved by E.KOBAYASHI

Mitaka PlantPhone:(0422)45-9538 No. 5-1-1, Shimorenjyaku Mitaka-shi, Telex:2822-351 Tokyo 181-8510 JapanFax: (0422)45-9957 CERTIFICATE TO:FEDERAL COMMUNICATIONS COMMISSION SUBJECT:TEST DATA FOR TYPE ACCEPTANCE OF NAVTEX RECEIVER FOR THE GMDSS MARITIME MF MOBILE SERVICE FCC ID:CKE NCR-330 Supplier/Manufacturer:Japan Radio Co., Ltd. 5-1-1 Shimorenjyaku, Mitaka City Tokyo 181-8510, Japan This is to certify that model NCR-330 NAVTEX RECEIVER complies with FCC performance standards including IMO resolution A.525 (13) and ITU-R Recommendation 540-2. This equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. To the best of my knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standard. Each unit manufactured, imported, or marketed, as defined in the Commission’s regulations, will confirm to the sample(s) tested within the variations that can be expected due to quantity production and testing on a statistical basis. Japan Radio Co., Ltd. E. Kobayashi, Manager, Maritime Communications Section I Engineering Department I Marine Electronics Division TEST RESULT FOR FCC CERTFICATION Purpose of test: Certify NCR-330 Grantee's type or model No.: NCR-330 Drawing, specification or exhibit: FCC Part 2 and 80 Quantity of item tested: One (1) of the above type Abstract: Refer to result sections Date tested completed: January 31, 2000 Tested by T.TAKAHASHI Checked by K.FUJII Approved by E.KOBAYASHI

NCR-330 BLOCK DIAGRAM HIGH-Z, 50 Ω A C T, A N T I N I C 1 T 4, F L 1 P R O T E C T I O N D I O D E S & B R E A K - I N R E L A Y T 1, T 2, T 3 T R 2 S T 1 B Z 1 I C 4 X1 4130.4 kHz C 2 9 T R 6I C 5 f f / 8 fosc=4130.4kHz L O C A L O S C I L L A T O R 1615.1785 Hz fL=516.3 kHz D C 9 V R E G R E C E I V E R S E C T I O N B K (DC10.8-35V) D C 5 V R E G P O W E R C O N T D C 9 V D C 5 V E X T A L A R M E C D I S I R C S E X T A L A R M T X D 1, C T S 1 T X D, C T S, R T S, R X D fo = 518 kHz P W R + F S _ I N T E S T _ C O N T T E S T _ S G D A _ S G A L M _ S G A G C C O U P L I N G T R 1 D C 5 V F S O U T F S I N0 I C 3 P O W E R S U P P L Y S E C T I O N F 1, F 2 C D 8 C M N - 2 3 3 0 R E C E I V E R DA OUT RS-422 DRIVER I C 9 I C 1 0 I C 2 K 2 K 2 I C 8 PHOTO COUPLER P H T 2 C D 1 3 ~ 1 8 T R 3, K 1 T B 1 J 2 J 3 D C I N J 1 I C 2 D S P AD IN J 2 I C 1 3 C O D E C I C 1 5 P L D 4.096 MHz 2.048 MHz 8 MHz I C 4 R O M 3 2 KB D S P A D D R E S S B U S C S O E I C 9 R A M 3 2 KB O E W E C S I C 1 0 R A M 3 2 KB O E W E C S D 0 - D 7 DR D IN D OUT DX RD BR WE PS I C 3 R O M 6 4 KB I C 7 R O M 3 2 KB XF P L D TIMER SELECT DRIVER DRIVER I C 1 C P U I C 8 EEPROM A D D R E S S B U S D A T A B U S D S P D A T A BUS MARK (Y) 1615 Hz : H SPACE (B) 1785 Hz : L MONI_CNTDATA I C 1 4 SW SCAN M A I N S WS T A T E S W J 3J 1 PWR SW FEED SW DIMMER SW TEST SW ALM OFF SW MENU SW STATE SW ENT SW CLR SW P R T D R I V E R P R T 1 P H O T O S E N S O R J 4 P H T 1 I C 1 2 P R I N T E R L E D C O N V E R T 1 6 S E G L E D P L D I C 1 5 P H T 2 X 2 4.096 MHz X 1 12.288MHz C D J - 2 3 3 0 M A I N P R O C E S S O R D E M O D U L A T E R S E C T O I N D C 5 V D C 5 V L E D W 1

NCR-330 BLOCK DIAGRAM HIGH-Z, 50 Ω A C T, A N T I N I C 1 T 4, F L 1 P R O T E C T I O N D I O D E S & B R E A K - I N R E L A Y T 1, T 2, T 3 T R 2 S T 1 B Z 1 I C 4 X1 4130.4 kHz C 2 9 T R 6I C 5 f f / 8 fosc=4130.4kHz L O C A L O S C I L L A T O R 1615.1785 Hz fL=516.3 kHz D C 9 V R E G R E C E I V E R S E C T I O N B K (DC10.8-35V) D C 5 V R E G P O W E R C O N T D C 9 V D C 5 V E X T A L A R M E C D I S I R C S E X T A L A R M T X D 1, C T S 1 T X D, C T S, R T S, R X D fo = 518 kHz P W R + F S _ I N T E S T _ C O N T T E S T _ S G D A _ S G A L M _ S G A G C C O U P L I N G T R 1 D C 5 V F S O U T F S I N0 I C 3 P O W E R S U P P L Y S E C T I O N F 1, F 2 C D 8 C M N - 2 3 3 0 R E C E I V E R DA OUT RS-422 DRIVER I C 9 I C 1 0 I C 2 K 2 K 2 I C 8 PHOTO COUPLER P H T 2 C D 1 3 ~ 1 8 T R 3, K 1 T B 1 J 2 J 3 D C I N J 1 I C 2 D S P AD IN J 2 I C 1 3 C O D E C I C 1 5 P L D 4.096 MHz 2.048 MHz 8 MHz I C 4 R O M 3 2 KB D S P A D D R E S S B U S C S O E I C 9 R A M 3 2 KB O E W E C S I C 1 0 R A M 3 2 KB O E W E C S D 0 - D 7 DR D IN D OUT DX RD BR WE PS I C 3 R O M 6 4 KB I C 7 R O M 3 2 KB XF P L D TIMER SELECT DRIVER DRIVER I C 1 C P U I C 8 EEPROM A D D R E S S B U S D A T A B U S D S P D A T A BUS MARK (Y) 1615 Hz : H SPACE (B) 1785 Hz : L MONI_CNTDATA I C 1 4 SW SCAN M A I N S WS T A T E S W J 3J 1 PWR SW FEED SW DIMMER SW TEST SW ALM OFF SW MENU SW STATE SW ENT SW CLR SW P R T D R I V E R P R T 1 P H O T O S E N S O R J 4 P H T 1 I C 1 2 P R I N T E R L E D C O N V E R T 1 6 S E G L E D P L D I C 1 5 P H T 2 X 2 4.096 MHz X 1 12.288MHz C D J - 2 3 3 0 M A I N P R O C E S S O R D E M O D U L A T E R S E C T O I N D C 5 V D C 5 V L E D W 1

NCR-330 BLOCK DIAGRAM HIGH-Z, 50 Ω A C T, A N T I N I C 1 T 4, F L 1 P R O T E C T I O N D I O D E S & B R E A K - I N R E L A Y T 1, T 2, T 3 T R 2 S T 1 B Z 1 I C 4 X1 4130.4 kHz C 2 9 T R 6I C 5 f f / 8 fosc=4130.4kHz L O C A L O S C I L L A T O R 1615.1785 Hz fL=516.3 kHz D C 9 V R E G R E C E I V E R S E C T I O N B K (DC10.8-35V) D C 5 V R E G P O W E R C O N T D C 9 V D C 5 V E X T A L A R M E C D I S I R C S E X T A L A R M T X D 1, C T S 1 T X D, C T S, R T S, R X D fo = 518 kHz P W R + F S _ I N T E S T _ C O N T T E S T _ S G D A _ S G A L M _ S G A G C C O U P L I N G T R 1 D C 5 V F S O U T F S I N0 I C 3 P O W E R S U P P L Y S E C T I O N F 1, F 2 C D 8 C M N - 2 3 3 0 R E C E I V E R DA OUT RS-422 DRIVER I C 9 I C 1 0 I C 2 K 2 K 2 I C 8 PHOTO COUPLER P H T 2 C D 1 3 ~ 1 8 T R 3, K 1 T B 1 J 2 J 3 D C I N J 1 I C 2 D S P AD IN J 2 I C 1 3 C O D E C I C 1 5 P L D 4.096 MHz 2.048 MHz 8 MHz I C 4 R O M 3 2 KB D S P A D D R E S S B U S C S O E I C 9 R A M 3 2 KB O E W E C S I C 1 0 R A M 3 2 KB O E W E C S D 0 - D 7 DR D IN D OUT DX RD BR WE PS I C 3 R O M 6 4 KB I C 7 R O M 3 2 KB XF P L D TIMER SELECT DRIVER DRIVER I C 1 C P U I C 8 EEPROM A D D R E S S B U S D A T A B U S D S P D A T A BUS MARK (Y) 1615 Hz : H SPACE (B) 1785 Hz : L MONI_CNTDATA I C 1 4 SW SCAN M A I N S WS T A T E S W J 3J 1 PWR SW FEED SW DIMMER SW TEST SW ALM OFF SW MENU SW STATE SW ENT SW CLR SW P R T D R I V E R P R T 1 P H O T O S E N S O R J 4 P H T 1 I C 1 2 P R I N T E R L E D C O N V E R T 1 6 S E G L E D P L D I C 1 5 P H T 2 X 2 4.096 MHz X 1 12.288MHz C D J - 2 3 3 0 M A I N P R O C E S S O R D E M O D U L A T E R S E C T O I N D C 5 V D C 5 V L E D W 1

1. GENERAL One of the features of Global Maritime Distress/Safety System (GMDSS) is high reliability established by automatic and introduction of digital techniques. The receiver executes the NAVTEX function that automatically receives and prints out NAVTEX service broadcasts supplied in English. The NAVTEX function receives and prints out the various type of information broadcast at a frequency of 518kHz, such as: navigational alert information, meteorological alert information, search-and-rescue information, and other types of information. The equipment also provides a method of programming so that you can select the type of information to be received and from which receiving station to receive it. 1.1 SCOPE AND PURPOSE The following technical data on the NCR-330 NAVTEX Receiver are submitted to the Federal Communications Commission for Type acceptance under Part 2 and 80 of the Commission’s rules and regulations. 1.2 NCR-330 Composition The NCR-330 consists of the following units and attachments: No.ComponentModel / Part Number Q’tyRemarks 1NAVTEX Receiver unitNCR-3301 2Mounting screwsMPTG020244 3Printer paperH-7ZPJD00441 4Instruction manualH-7ZPJD00671 5Operating cardH-7ZPJD00691 6Spare fuseH-6ZXAF000211 7Ship Registration FormH-7ZPJD00651 2. TYPE NUMBER TYPE: NAVTEX Receiver MODEL: NCR-330 FCC ID: CKE NCR-330 3. SPECIFICATION 3.1 Electrical specifications (1) NAVTEX Receiver unit a. Receiver Receiving frequency 518kHz Receiving scheme STRAIGHT Receiving mode F1B Gain Max. character error ratio: 1% at an antenna input of 1μV Antenna input Special antenna(NAW-330) BK 12VDC or 24VDC External alarm interface Open-collector type Max: 500mA at 35VDC Recommended product: CGC-300A Max. power consumption: 20mA Audio output level: 85dB/m Receiving format 7-bit error detection code based on the NAVTEX broadcasting format b. Printer Printing schemeThermosensitive 7×6 or 7×5 dot matrix Total characters/line35 or 40 Printer paperTF50KS-E3, 80mm×60mm across×40m Out-of-paper warningAlarm buzzer Operating panel lamp blinking Red end-of-paper line marks on printer paper (the red lines indicate there is one meter or less remaining ) c. Control switches Power on/off Receiving coast…

Text truncated - open the document above for the full version.