F6OINBODYBAND3Body Composition Analyzer

User Manual ※ This manual can be downloaded from hhtp://www.inbody.com. InBodyBAND3 User's Manual Contents 1. Introduction of products Precautions Product components Name of product part 2. Preparing for Use Powering and Charging Link Apps Turn on the screen Toggle Screen Replacing Strap 3. Introduction of Features Main Clock Screen Inbody Inspection Walking sleep Heart rate Message Notification weather exercise Stopwatch / Timer / Alarm Music Control Walk Notification Move Notification Wear Notification System EZ Training 4. Product specification 5. Product Warranty 1. Introduction of products Precautions Warning • Do not measure a person wearing a life-saving medical device such as a pacemaker or a patient monitoring device inside the body. • The current used for measurement is not harmful to the human body, but pregnant women should use it after consulting an expert. • Because this product is not a medical device, it is not possible to determine the presence of a disease, and a doctor's examination is required to determine the presence of a disease. CAUTION 'Caution' is intended to prevent accidents or dangers by using the product safely and properly, so be sure to follow it. • Inspection results may vary depending on the environment and measurement conditions. • Measure indoors as much as possible in cold weather (body components, heart rate). • This product has been tested in a controlled environment and is waterproof/dustproof under certain circumstances. (International Standard IEC 60529 - Degrees of Protection provisioned by Enclosures [IP Code] meets the requirements of IP68). However, in some situations, flooding damage may not be prevented. • Do not randomly decompose or shock the product. This may result in electrical shock or injury, product failure and inaccurate results, and subsequent warranty service from the manufacturer is not available. • Forced to open, decompose, break, bend, deform, drill, pressure, or crush the product. Don't. • Do not forcibly open, disassemble, break, bend, deform, puncture, pressure, or crush the product. • Do not immerse the product in seawater or chemical solutions (such as soap). • Do not leave the product in the bath or hot water. • Do not leave the product unattended in a place where high-pressure water can be sprayed (water from the faucet, waterfalls, waves, etc.) or use the product under water. • Be careful not to bend the product too much. Product damage may occur. • Dropping or impact on the product may cause major device damage or deformation, resulting in leakage. • Store out of reach of pets or children. If you put the product in your mouth or bite it, there may be a risk of suffocation, battery explosion, etc. • Do not leave it indoors, on electric pads, or in hot and humid environments such as steam rooms. The appearance may be deformed, broken, or exploded. • Do not expose the product to direct sunlight for a long time or use it in humid places such as bathrooms. • Do not alter or modify batteries, insert external objects, immerse or expose them to water or other liquids. • Recharge the battery before it discharges because the battery life will decrease if it lasts for a long time. • Battery life may vary slightly depending on inspection, synchronization, and usage options. • Do not cover or cover it with a blanket during use or while charging. There may be a risk of fire. • Do not use it if you are allergic to metal, rubber, or silicone materials. • Clean and dry the product regularly, especially on areas that come into contact with the skin. • Tight band wear or sensitive skin may cause skin reactions • prolonged exposure to stimuli such as soap, sweat, or skin reactions may be caused by allergies, environmental factors, and other factors. • Keep straps clean and dry. • Do not connect the product to other equipment in a way that is not indicated in the user manual. • Keep the electrode parts of the product away from electrical conductive materials. Electrical stimulation, such as static electricity, can cause product damage or failure. • Do not check phone notifications or other data displayed on the product's display while driving or in situations where inadvertent hazards may occur. • Straps may be contaminated by direct sunlight, water, oil, or cosmetics, and may be discolored or deformed. • Do not shock while the charging USB cable is plugged in. • Be careful not to bend the charging USB cable. If the USB cable is damaged, stop using it. • This device is home (class B) electromagnetic compatible and is available in all regions. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. • This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: - This device may not cause interference. - This device must accept any interference, including interference that may cause undesired operation …

Text truncated - open the document above for the full version.

Letter of Authorization Company : InBody Co., Ltd. Address : InBody Bldg., 625, Eonju-ro, Gangnam-gu, Seoul, 06106, South Korea Product Name : Body Composition Analyzer Model Number : InBodyBAND3 FCC Identifier : F6OINBODYBAND3 We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Kyung Keun, Kim Date: October 5, 2021 Title: Manager Signature of applicant:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: October 5, 2021 Subject; Request for Confidentiality FCC ID: F6OINBODYBAND3 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Kyung Keun, Kim Title: Manager

Page 1 of 6 Page 2 of 6 Page 3 of 6 Page 4 of 6 Page 5 of 6 Page 6 of 6

Page 1 of 1 IDENTIFICATION LABEL: PROPOSED LABEL The shall be permanently affixed in the rear side of the equipment

Page 1 of 9 Page 2 of 9 Page 3 of 9 Page 4 of 9 Page 5 of 9 Page 6 of 9 Page 7 of 9 Page 8 of 9 Page 9 of 9 Chip Antenna

Page 1 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : OT-218-RWD-094 Reception No. : 2104002116 Applicant : InBody Co., Ltd. Address : InBody Bldg., 625, Eonju-ro, Gangnam-gu, Seoul, 06106, South Korea Manufacturer : InBody Co., Ltd. Address : 15, Heugam-gil, Ipjang-myeon, Seobuk-gu, Cheonan-si, Chungcheongnam-do 31025 KOREA Type of Equipment : Body Composition Analyzer FCC ID. : F6OINBODYBAND3 Model Name : InBodyBAND3 Serial number : N/A Total page of Report : 6 pages (including this page) Date of Incoming : August 09, 2021 Date of issue : August 30, 2021 SUMMARY The equipment complies with the regulation; FCC 47 CFR Part 1, 1.1310 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Tested by Myeong-Hwa, Jang / Manager ONETECH Corp. Reviewed by Tae-Ho, Kim / Senior Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 5 3. EUT MODIFICATIONS .................................................................................................................................................... 5 4. RF EXPOSURE EVALUATION ...................................................................................................................................... 6 4.1 RF EXPOSURE CALCULATION ....................................................................................................................................... 6 4.2 EUT DESCRIPTION ......................................................................................................................................................... 6 4.3 TEST RESULT OF SAR EXCLUSION FOR DEVICES ........................................................................................................ 6 Page 3 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) Revision History Rev. No. Issue Report No. Issued Date Revisions Section Affected 0 OT-218-RWD-094 August 30, 2021 Initial Release All Page 4 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 1. VERIFICATION OF COMPLIANCE Applicant : InBody Co., Ltd. Address : InBody Bldg., 625, Eonju-ro, Gangnam-gu, Seoul, 06106, South Korea Contact Person : Dong-Hyun Woo / Strategic Certification Team / Assistant manager Telephone No. : +82-2-300-2244 FCC ID : F6OINBODYBAND3 Model Name : InBodyBAND3 Brand Name : Serial Number : N/A Date : August 30, 2021 EQUIPMENT CLASS DTS – DIGITAL TRNSMISSION SYSTEM E.U.T. DESCRIPTION Body Composition Analyzer THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES ANSI C63.10: 2020 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) FCC PART 15 SUBPART C Section 15.247 KDB 558074 D01 15.247 Meas Guidance v05r02 Modifications on the Equipment to Achieve Compliance None Final Test was Conducted On 3 m, Semi Anechoic Chamber -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 2. GENERAL INFORMATION 2.1 Product Description The InBody Co., Ltd., Model InBodyBAND3 (referred to as the EUT in this report) is a Body Composition Analyzer. The product specification described herein was obtained from product data sheet or user’s manual. DEVICE TYPE Body Composition Analyzer OPERATING FREQUENCY 2 402 MHz ~ 2 480 MHz MODULATION TYPE GFSK RF OUTPUT POWER -9.58 dBm NUMBER OF CHANNEL 40 Channel ANTENNA TYPE Chip Antenna ANTENNA GAIN 3.70 dBi List of each Osc. or crystal Freq.(Freq. >= 1 MHz) 32.768 MHz, 38.4 MHz 2.2 Alternative type(s)/model(s); also covered by this test report. -. None 3. EUT MODIFICATIONS -. None Page 6 of 6 Report No.: OT-218-RWD-094 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0)…

Text truncated - open the document above for the full version.

Page 1 of 36 Report No.: OT-218-RWD-093 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : OT-218-RWD-093 Reception No. : 2104002116 Applicant : InBody Co., Ltd. Address : InBody Bldg., 625, Eonju-ro, Gangnam-gu, Seoul, 06106, South Korea Manufacturer : InBody Co., Ltd. Address : 15, Heugam-gil, Ipjang-myeon, Seobuk-gu, Cheonan-si, Chungcheongnam-do 31025 KOREA Type of Equipment : Body Composition Analyzer FCC ID. : F6OINBODYBAND3 Model Name : InBodyBAND3 Serial number : N/A Total page of Report : 36 pages (including this page) Date of Incoming : August 09, 2021 Date of issue : August 30, 2021 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Tested by Myeong-Hwa, Jang / Manager ONETECH Corp. Reviewed by Tae-Ho, Kim / Senior Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 36 Report No.: OT-218-RWD-093 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 5 2. TEST SUMMARY .............................................................................................................................................................. 6 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 6 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 6 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 6 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 6 2.5 TEST METHODOLOGY .................................................................................................................................................... 6 2.6 TEST FACILITY ............................................................................................................................................................... 6 3. GENERAL INFORMATION ............................................................................................................................................ 7 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 7 4. EUT MODIFICATIONS .................................................................................................................................................... 7 5. SYSTEM TEST CONFIGURATION ............................................................................................................................... 8 5.1 JUSTIFICATION ............................................................................................................................................................... 8 5.2 PERIPHERAL EQUIPMENT .............................................................................................................................................. 8 5.3 MODE OF OPERATION DURING THE TEST ...................................................................................................................... 9 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................. 11 6. PRELIMINARY TEST .................................................................................................................................................... 11 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ....................................................................................................... 11 6.2 GENERAL RADIATED EMISSIONS TESTS ..................................................................................................................... 11 7. MINIMUM 6 DB BANDWIDTH .................................................................................................................................... 12 7.1 OPERATING ENVIRONMENT ......................................................................................................................................... 12 7.2 TEST SET-UP ................................................................................................................................................................. 12 7.3 TEST DATE ................................................................................................................................................................... 12 7.4 TEST DATA FOR 1 MBPS ............................................................................................................................................... 13 8. MAXIMUM PEAK OUTPUT POWER ......................................................................................................................... 15 8.1 OPERATING ENVIRONMENT .................…

Text truncated - open the document above for the full version.

Page 1 of 3 - Conducted Emission Test Page 2 of 3 - Radiated Emission Test Page 3 of 3