FDIBSMBW02R-02.4GHz wireless receiver

무선 전파에 대한 주의사항 • 다음과 같은 곳에서는 본 제품을 사용하지 마십시오: 자기장, 정전기 또는 무선 간섭이 발생하는 전자레인지 부근. 약 2.4 GHz의 무선 전파를 사용하는 물체 부근 (환경에 따라서는 전자파가 도달하지 않을 수도 있습니다.) • 본 제품은 다음 기기 및 무선 기지국과 같은 무선 채널 주파수를 사용합니다: • 산업, 과학 및 의료 기기 • 공장 생산 라인에 사용되는 모바일 오브젝트 인식용 무선국 (1) 공장내 무선국(라이센스 필요) (2) 지정 저출력 무선국(라이센스 불필요) 사용상의 주의 • 마우스의 센서부분을 청결하게 유지하고 손상되지 않도록 하십시오. • 마우스 버튼을 장시간 누른 상태로 하거나, 마우스를 연속적으로 움직이면 배터리 소모가 빨라진다는 것에 주의하십시오. • 마우스를 가방 또는 파우치에 넣어서 운반할 때에는 전원을 OFF로 해주십시오. 2.4GHz 무선 마 우스를 사용하기 위한 안 전 주의사항 블루 LED 광학 센서는 매우 민감합니다. 그렇지만, 그 특성으로 인해서 반사가 잘 되는 빛나는 표면이나 색상이 진하거나 또는 패턴 표면에서는 잘 작동하지 않거나 작동할 수 없을 수도 있습니다. 사용환경에 따라서는 센서주위에 먼지가 쌓여서 센서의 감도가 떨어질 수 있습니다. 이런 경우에는 에어더스터 등을 사용해서 먼지를 제거해 주십시오. BSMBW02 / BSMBW02R 사용설명서 다국어 설명서 <주목> 본 마우스는 부속된 수신기로만 사용할 수 있습니다. 수신기를 분실한 경우에는 같은 모델이라도 다른 수신기와 기기를 사용할 수 없습니다. 수신기는 매우 작으므로 취급에 주의해 주십시오. 비자성체(목제 책상 등) 약 10 m 자성체(스틸 책상 등) 약 3 m 값은 내부 시험에 의해 얻어진 것이며, 값을 보증하지는 않습니다. 무선 전파 범위무선 전파 범위 배터리 표시등배터리 표시등 1. 기기의 배터리 용량이 충분한 상태로 ON 으로 하면 배터리 표시등이 약 3초간 켜진 후에 꺼집니다. 2. 배터리 용량이 적은 경우에는 배터리 표시등이 적색으로 점멸합니다. 배터리 표시등이 적색으로 점멸하면 배터리를 교체합니다. 기기운반의 편의를 위해 수신기는 마우스 후면에 보관할 수 있습니다. 장기간 기기를 사용하지 않는 경우나 기기를 운반하려고 하는 경우에는 전원스위치를 OFF로 해서 전력을 절약합니다. 보관하려면 마우스 뒷쪽의 오목 들어간 곳에 수신기를 슬라이드시킵니다. 수신기는 마우스 내부에 보관할 수 있습니다.수신기는 마우스 내부에 보관할 수 있습니다. 참고 위의 모든 절차는 OS의 일본어 버전을 토대로 한 것입니다. 절차는 사용하는 OS에 따라 달라질 수 있습니다. 주의 • • • • • • • Frequency band 2.4GHz Modulation GFSK Assumed interference range 10 m or less Advisability of frequency change Entire bandwidth is being used, and use of the same bandwidth as the "in-plant wireless station" or "specified low power wireless station" is unavoidable Precautions with Regards to Radio Waves • Do not use this product in the following places: Near a microwave oven where magnetic field, static electricity or radio disturbance occurs. In t h e v i c i n i t y o f o b j e c t s u s i n g r a d i o w a v e s o f approximately 2.4 GHz (the radio waves may not reach depending on the environment.) • This product uses the same radio channel frequency as the following equipment and wireless stations: • Industrial, scientific, and medical equipments • Wireless stations for mobile object identification used in factory production lines (1) In-plant wireless station (license required) (2) S p e c i f i e d l o w p o w e r w i r e l e s s s t a t i o n (license not required) 1. Make sure there are no in-plant wireless stations or specified low power wireless stations for mobile object identification operating in the vicinity before using this product. 2. Should this product causes radio wave interference with an in-plant wireless station for mobile object identification, immediately change the location where this product is used, or stop radio wave emission to avoid radio wave interference. 3. This product is equipped with a function that automatically avoids radio wave interference. If the product still causes radio wave interference, stop using it immediately. 4. Please contact our Technical Support Center for any other problems such as radio wave i n t e r f e r e n c e w i t h a s p e c i f i e d l o w p o w e r wireless station for mobile object identification caused by this product. Precautions for Use • Keep the sensor part of the mouse clean and prevent it from getting damaged. • Please note that batteries will drain faster if the mouse button is held down for long periods, or if the mouse is moved continually. • Turn the power OFF when carrying the mouse in bag or pouch. Safety Precautions for Using the 2.4GHz Wireless Mouse The BlueLED optical sensor is extremely sensitive. However, due to its nature, it may have difficulty operating or may not be able to operate at all on highly reflective shiny surfaces, or intensely colored or pattern surfaces. Depending on the usage environment, dust collect around the sensor and reduce the sensitivity of the sensor. In this case, use an air duster etc. to remove the dust. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. BSMBW02 / BSMBW02R Instruction Manual Multilanguage Manual <Attention> This mouse can only be used with the supplied receiver. Should the receiver be lost, the unit cannot be used with a different receiver even if it is from the same model. Be careful handling the receiver as it is very small. A s t h i s p r o d u c t i s s h i p p e d w i t h t h e mouse and receiver already connected, y o u d o n o t n e e d t o c o n n e c t t h e m . However, if the mouse response is poor due to the influence of a wireless LAN etc., perform the connection process. …

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

Label location

Page 2 Page 3

FCC ID: FDIBSMBW02R-0 Report No.: RF120322C25 Operational Description This device is a 2.4GHz wireless receiver. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is printed antenna. The other instruction, please have a look at the users manual.

Report No.: RF990811C15D 1 Report Format Version 4.2.0 Reference No.: 990811C15, 120322C25 FCC TEST REPORT REPORT NO. :RF990811C15D MODEL NO. :BSMBW02R FCC ID:FDIBSMBW02R-0 RECEIVED :Aug. 11, 2010 TESTED :Aug. 12 ~ Aug. 14, 2010 ISSUED :Mar. 27, 2012 APPLICANT: BUFFALO INC. ADDRESS: AKAMONDORI B1dg., 30-20, Ohsu 3-chome, Naka-Ku, Nagoya ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 31 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Report No.: RF990811C15D 2 Report Format Version 4.2.0 Reference No.: 990811C15, 120322C25 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION .......................................................................................................... 4 2. SUMMARY OF TEST RESULTS .................................................................................. 5 2.1 MEASUREMENT UNCERTAINTY ............................................................................... 5 3. GENERAL INFORMATION ........................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 6 3.2 DESCRIPTION OF TEST MODES ............................................................................... 7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................... 8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 10 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................................... 10 4. TEST TYPES AND RESULTS .................................................................................... 11 4.1 RADIATED EMISSION MEASUREMENT .................................................................. 11 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT ................................................ 11 4.1.2 TEST INSTRUMENTS ............................................................................................... 12 4.1.3 TEST PROCEDURES ................................................................................................ 13 4.1.4 DEVIATION FROM TEST STANDARD ...................................................................... 13 4.1.5 TEST SETUP ............................................................................................................. 14 4.1.6 EUT OPERATING CONDITIONS ............................................................................... 14 4.1.7 TEST RESULTS ......................................................................................................... 15 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 21 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 21 4.2.2 TEST INSTRUMENTS ............................................................................................... 21 4.2.3 TEST PROCEDURES ................................................................................................ 22 4.2.4 DEVIATION FROM TEST STANDARD ...................................................................... 22 4.2.5 TEST SETUP ............................................................................................................. 23 4.2.6 EUT OPERATING CONDITIONS ............................................................................... 23 4.2.7 TEST RESULTS ......................................................................................................... 24 4.3 BAND EDGES MEASUREMENT ............................................................................... 26 4.3.1 LIMITS OF BAND EDGES MEASUREMENT ............................................................ 26 4.3.2 TEST INSTRUMENTS ............................................................................................... 26 4.3.3 TEST PROCEDURE .................................................................................................. 26 4.3.4 DEVIATION FROM TEST STANDARD ...................................................................... 26 4.3.5 EUT OPERATING CONDITION ................................................................................. 26 4.3.6 TEST RESULTS ......................................................................................................... 27 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ................................................. 29 6. INFORMATION ON THE TESTING LABORATORIES ............................................... 30 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ......................................................................................... 31 Report No.: RF990811C15D 3 Report Format Version 4.2.0 Reference No.: 990811C15, 120322C25 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF990811C15D Original release Mar. 27, 2012 Report No.: RF990811C15D 4 Report Format Version 4.2.0 Reference No.: 990811C15, 120322C25 1. CERTIFICATION PRODUCT: 2.4GHz wireless receiver MODEL NO.: BSMBW02R BRAND: iBUFFALO APPLICANT: BUFFALO INC. TESTED: Aug. 12 ~ Aug. 14, 2010 TEST …

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4