FFMGT-8320CCordless Telephone

900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. OPERATION DESCRIPTION ( MODEL : GT- 8320C ) SK : TCTU0001801-MG DESCRIPTION : OPERATION DESCRIPTION OF GT-8320C DATE Iss.SHEETSNOTICE NO.DESIGNER CHECKER ’00. 07. 24 1 28 K961/26/8903 Y. H. JiJ. H. Lee 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. GT-8320C (900MHz DSST WITH CALLER ID , CALLWAITING ID, SPEAKER PHONE and ANSWERING SYSTEM) MANUAL This equipment has tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measurements: ❏ Reorient or relocate the receiving antenna. ❏ Increase the separation between the equipment and receiver. ❏ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ❏ Consult the dealer or an experienced radio/TV technician for help. ! C AUTION Changes or modification to device not expressly approved by LGE could void the user’s authority to operate this equipment. Copyright  2000 by LGE. All rights reserved. ! Warning This equipment will be inoperable when mains power fails. ! Important Notice Since this equipment has very low output power ( EIRP <10 mW), it complies with the FCC RF Exposure Limit. MODEL GT-8320C 1999 LGIC. No part of this publication may reproduced, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without the written permission of LGIC. 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. G ETTING TO K NOW Y OUR N EW P HONE Your new GT-8320C telephone gives you the ultimate in cordless telephone sound quality with the luxury of Caller ID and Call Waiting ID If this is your first cordless telephone, you'11 soon discover that your cordless is similar to regular telephone, except without the cord. If you've owned a cordless in the past, you'll discover that the GT8320C telephone is the most powerful and full-functioned Call Waiting ID cordless telephone on the market. Some key features are: ❍ 60 name and number Caller ID/Call Waiting ID me mo r y ❍ 20 name and number programmable memory ❍ Hearing-aid compatibility ❍ High quality digital security communication ❍ Dual mode voice mail serviceable (FSK , STUTTER) Unlike regular telephones, your cordless does not work during power failures. Because of this restriction, we do not recommend you have only cordless telephone in your residence. U NPACKING Y OUR P HONE In addition to this handbook, check that you have: 7 Foot Line Cord for Wall Mounting D-AA600 x 3 3.6V 600mA Battery (This might not be pre-installed in your handset) AC Adapter 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. L OCATING K EYS, L IGHT, AND S WITCHES O N THE B ASE  The PAGE key - is a ho mi ng s yste m for fi ndi ng the ha ndset. If you press the PAGE key once, the handset beeps for 15seconds.  IN USE light - becomes lit when the GT-8320C is being used.  CHARGE light - comes on solid when the handset is in the base.  VOICE MAIL lig ht – flas hes slow ly to alert yo u w he n yo u receive new messages in your Voice mail messages mail box. MESSAGE WAITING appears on the display . NEWCALL light – flashes more slowly when you receive new calls. This light continues to flash until you review the newcalls OO uu S S P P K K 123 456 789 * P P r r o o g g r r a a R R e e c c o o r r d d M M e e m m o o r r • / • P P a a g g M M e e m m Ne w • • Vol um e • Flas h Redial / P .Tim.Alar . RinConfir •• •• Eras 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. Ke y s TALK key - Turns the phone on or off so you can dial or talk. Voice mail key - . Directly access your V.Mail service Dialing keys - Control manual dialing. Scroll keys " # Scrolls through your Callers log Redial key - Redials your last out- bound call or inserts a pause in a number when entering numbers into memory. O N THE H ANDSET DELETE Key- Removes records from the Callers log or from memory dialing. MEM key-Allows you to store frequently dialed numbers and to dial directly from the speed dialing list. FLASH key- Allows you to switch between a call and a Call Waiting call. PGM key-Allows you to program your setting up your function or to edit a name and number in memory. VOLUM E UP/DOWN KEY- Allows you to adjust the loudness of the handset earpiece, or the ringer or allows you to edit the character at Memory mode. VOLUME    12 : 22 PM 12 / 01 CALL 01 ✉ ✉✉ ✉ 1- 555 – 123 - 4567 SMITH JOHN DEL VM TALK 2 ABC3 DEF 4 GHI5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ * 7 0 OPER 10 # +1 MUTE FLASH MEM !" PGM 1 RE/PA 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. HEADSET Jack Allows you to add a headset to the handset (not included, but available by order.) HEADSET JACK 900MHz DSST PHONE with CALLER ID, SPK PHONE and ANSWERING SYSTEM. SETTING UP YOUR PHONE Now that you've checked the contents of the carton, it only takes a few steps to set up your phone. STEP 1. CHOOSE A CENTRAL LOCATION FOR THE BASE UNIT The base should be away from all other electronic equipment such as a personal computer, microwave, stereo ,or television. It is also a good idea to place th…

Text truncated - open the document above for the full version.

Exhibit 13 Exhibit 13: Cover Letters December 7, 2000 FEDERAL COMMUNICATIONS COMMISSION Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Enclosed is the documentation for a spread spectrum transmitter operating under FCC Part 15, Subpart C, Section 15.247. This application was certified by Communication Certification Laboratory (CCL) under the TCB (Scope A4) program. The applicant, model number and FCC ID are listed below: Applicant: LG Electronics, Inc. Model: GT-8320C FCC ID: FFMGT-8320C Please let me know if I can be of further assistance. Sincerely yours, COMMUNICATION CERTIFICATION LABORATORY Joseph W. Jackson V.P. Marketing

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT External Photos FOR LG ELECTRONICS, INC. LG Kangseo B/D, 36, Munlae-Dong, 6-Ga, Youngdungpo-Gu, Seoul, 150-096, Korea FCC ID: FFMGT-8320C October 30, 2000 This Report Concerns: Original Report Equipment Type: Digital Spread Spectrum Cordless Phone – Household Appliances Test Engineer: Hien Pham Test Date: October 12, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 Tel: (408) 732-9162 Fax: (408) 732-9164 LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT External photo Page 2 of 2 FCC Part 15 Subpart C Test Report TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)........................................................................................3 1.2 OBJECTIVE................................................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................................3 1.4 TEST METHODOLOGY..............................................................................................................................................................3 1.5 TEST FACILITY.........................................................................................................................................................................4 1.6 TEST EQUIPMENT LIST............................................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................................5 1.8 EUT CONFIGURATION DETAILS AND LIST...........................................................................................................................5 1.9 EXTERNAL I/O CABLING........................................................................................................................................................5 2 – EUT PHOTOGRAPHS...........................................................................................................................................................6 2.1 EUT – BASE TOP VIEW..........................................................................................................................................................6 2.2 EUT – HANDSET TOP VIEW...................................................................................................................................................7 2.3 EUT OVERALL VIEW WITH POWER ADAPTER....................................................................................................................8 APPENDIX A – AGENT AUTHORIZATION LETTER....................................................................................................9 LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT External photo Page 3 of 3 FCC Part 15 Subpart C Test Report 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The LG Electronic, Inc., FCC ID FFMGT-8320C or the "EUT" as referred to in this report is a Digital Spread Spectrum Cordless Phone which has 20 channel possible in the 904-926 MHz Bandwidth, and the transmission range up to 1 Km in open sight (longer range than analog 900MHz cordless phone). The EUT was composed of two parts: one is the handset which measures 9” L x 2.125” W x 1.675” H, the other is the base which measures 7” L x 5.5” W x 2.25” H. 1.2 Objective This type approval report is prepared on behalf of LG Electronics, Inc., in accordance with Part 2, Subpart J, Part 15, Subparts A and B of the Federal Communication Commissions rules. The objective of the manufacturer is to demonstrate compliance with FCC rules for Output Power, 6 dB Bandwidth, Power Density, Band Edge, Spurious Emission, Processing Gain, Antenna Gain, and Conducted and Radiated Emission. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT External photo Page 4 of 4 FCC Part 15 Subpart C Test Report 1.5 Test Facility The Open Area Test Site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test site at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-1992. The Federal Communications Commi…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT FCC ID Label Location FOR LG INFORMATION & COMMUNICATIONS, LTD. LG Kangseo B/D, 36, Munlae-Dong, 6-Ga, Youngdungpo-Gu, Seoul, 150-096, Korea FCC ID: FFMGT-8320C October 30, 2000 This Report Concerns: Original Report Equipment Type: Digital Spread Spectrum Cordless Phone – Household Appliances Test Engineer: Hien Pham Test Date: October 12, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 Tel: (408) 732-9162 Fax: (408) 732-9164 LG Electronics Inc. FCC ID: FFMGT-8320C Report # FCC ID Label Page 2 of 2 FCC Part 15 Subpart C Test Report TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)........................................................................................3 1.2 OBJECTIVE................................................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................................3 1.4 TEST METHODOLOGY..............................................................................................................................................................3 1.5 TEST FACILITY.........................................................................................................................................................................4 1.6 TEST EQUIPMENT LIST............................................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................................5 1.8 EUT CONFIGURATION DETAILS AND LIST...........................................................................................................................5 1.9 EXTERNAL I/O CABLING........................................................................................................................................................5 2 – FCC PRODUCT LABELING AND WARNING STATEMENT................................................................................6 2.1 FCC ID LABEL.........................................................................................................................................................................6 2.2 PROPOSED LABEL LOCATION ON EUT.................................................................................................................................6 2.3 FCC WARNING STATEMENT..................................................................................................................................................6 APPENDIX A – AGENT AUTHORIZATION LETTER....................................................................................................7 LG Electronics Inc. FCC ID: FFMGT-8320C Report # FCC ID Label Page 3 of 3 FCC Part 15 Subpart C Test Report 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The LG Electronic, Inc., FCC ID FFMGT-8320C or the "EUT" as referred to in this report is a Digital Spread Spectrum Cordless Phone which has 20 channel possible in the 904-926 MHz Bandwidth, and the transmission range up to 1 Km in open sight (longer range than analog 900MHz cordless phone). The EUT was composed of two parts: one is the handset which measures 9” L x 2.125” W x 1.675” H, the other is the base which measures 7” L x 5.5” W x 2.25” H. 1.2 Objective This type approval report is prepared on behalf of LG Electronics, Inc., in accordance with Part 2, Subpart J, Part 15, Subparts A and B of the Federal Communication Commissions rules. The objective of the manufacturer is to demonstrate compliance with FCC rules for Output Power, 6 dB Bandwidth, Power Density, Band Edge, Spurious Emission, Processing Gain, Antenna Gain, and Conducted and Radiated Emission. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. LG Electronics Inc. FCC ID: FFMGT-8320C Report # FCC ID Label Page 4 of 4 FCC Part 15 Subpart C Test Report 1.5 Test Facility The Open Area Test Site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test site at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-1992. The Federal Communications Commission and Voluntary Control Coun…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT Internal Photos FOR LG ELECTRONICS, INC. LG Kangseo B/D, 36, Munlae-Dong, 6-Ga, Youngdungpo-Gu, Seoul, 150-096, Korea FCC ID: FFMGT-8320C October 30, 2000 This Report Concerns: Original Report Equipment Type: Digital Spread Spectrum Cordless Phone – Household Appliances Test Engineer: Hien Pham Test Date: October 12, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 Tel: (408) 732-9162 Fax: (408) 732-9164 LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT Internal photo Page 2 of 2 FCC Part 15 Subpart C Test Report TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)........................................................................................3 1.2 OBJECTIVE................................................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................................3 1.4 TEST METHODOLOGY..............................................................................................................................................................3 1.5 TEST FACILITY.........................................................................................................................................................................4 1.6 TEST EQUIPMENT LIST............................................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................................5 1.8 EUT CONFIGURATION DETAILS AND LIST...........................................................................................................................5 1.9 EXTERNAL I/O CABLING........................................................................................................................................................5 2 – EUT PHOTOGRAPHS...........................................................................................................................................................6 2.1 EUT BASE – ENCLOSURE OFF VIEW....................................................................................................................................6 2.2 EUT BASE ENCLOSURE OFF BOARD VIEW.......................................................................................................................7 2.3 EUT HANDSET ENCLOSURE VIEW........................................................................................................................................8 2.4 EUT HANDSET ENCLOSURE OFF BOARD VIEW..................................................................................................................9 APPENDIX A – AGENT AUTHORIZATION LETTER..................................................................................................10 LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT Internal photo Page 3 of 3 FCC Part 15 Subpart C Test Report 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The LG Electronic, Inc., FCC ID FFMGT-8320C or the "EUT" as referred to in this report is a Digital Spread Spectrum Cordless Phone which has 20 channel possible in the 904-926 MHz Bandwidth, and the transmission range up to 1 Km in open sight (longer range than analog 900MHz cordless phone). The EUT was composed of two parts: one is the handset which measures 9” L x 2.125” W x 1.675” H, the other is the base which measures 7” L x 5.5” W x 2.25” H. 1.2 Objective This type approval report is prepared on behalf of LG Electronics, Inc., in accordance with Part 2, Subpart J, Part 15, Subparts A and B of the Federal Communication Commissions rules. The objective of the manufacturer is to demonstrate compliance with FCC rules for Output Power, 6 dB Bandwidth, Power Density, Band Edge, Spurious Emission, Processing Gain, Antenna Gain, and Conducted and Radiated Emission. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. LG Electronics, Inc. FCC ID: FFMGT-8320C Report # EUT Internal photo Page 4 of 4 FCC Part 15 Subpart C Test Report 1.5 Test Facility The Open Area Test Site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test site at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facilit…

Text truncated - open the document above for the full version.

CIRCUIT DESCRIPTION ( MODEL : GT-8320C) SK : TCTU0001801-DS DESCRIPTION : CIRCUIT DESCRITION OF GT-8320C DATE Iss. SHEETS NOTICE NO. DESIGNER CHECKER ’00. 07. 24 1 3 K961/26/8903 Y. H. Ji J. H. Lee BASE. The signal, which inputted in TEL-LINE, is DC coupled at TR and transformed Analog into Digital at U100. DATA that is transformed into Digital signal is mixed with PN code at U100 (by spread spectrum) and transmitted to RF part. Spreading signal, which inputted to RF part, is mixed with Carrier supplied to VCO at U1 and create TX frequency of using channel and then is transmitted to ANTENNA through U3 by TX control of D1,D2. The signal received to antenna is transmitted to U1 by RX/TX control time. The signal inputted at U1 is mixed Carrier of VCO and got to direct conversion and create Base band signal. And then, create I and Q signal by demodulation (QPSK: Quadrature Phase Shift Keying method is phase- shifted by 90° ) I and Q signal (Two signal phase is 90°) is transmitted to U100 and remixed with PN code and generated Digital signal. Digital signal is transformed into Analog at U100. This audio signal is passed through U100 and transmitted to TEL-LINE through the Transformer (TR). Caller ID signal which inputted to the Tel-Line (in case of TYPEI) passes through C333,C334,R350U,R351,110 and then, is transformed into digital data at U111 and is transmitted to U100. (When RX mute is LOW, The FSK DATA is received) (in case of TYPEII) passes through Transformer(TR),C324,R337,U110 and then, transformed into digital data at U111 (When RX mute is high The CAS signal is received and then RX mute is LOW to receive the FSK signal) and is transmitted to U100. The transformed signal into digital data is transmitted to the Handset ,and then The Handset is displayed CID data. Line in use state : When the Unit is offhook or the line is off hook state, The Line detect port is high though R300, R301,Bridge diode and U113. When the Unit is on hook or the line is on hook state, The Line detect port is low. When the ring is incoming into the Tel-line, The signal passes through C146,D107,D108,U105 and then detected at U100. The ring data is transformed into Analog to Digital at U100 and transmitted to the Handset. DSP Part DSP (U117, D16551) can record voice, control the Flash memory, constrict, record, play and erase voice signal. This IC include CODEC that convert the Analog signal to Digital signal and vice versa. Flash menory(Audio RAM) can record the constricted digital signal from DSP IC and output the stored signal to DSP IC to play the voice signal. CPU (U119) is a master CPU to control the DSP Part, This CPU control the Tx, Rx, signal path, receive the key Input signal, turn on and off the function LEDs. ID setting When the handset is placed on the baseunit , The charge data is transmitted to handset Through R130,R150,Q105, R147,Q101,L103,L102 and CT(contact) of the baseunit. The handset is received ID through charger contact, Bridge diode, R151 and transmitted ACK signal to RF PART. Y100 is X-tal generating RF - reference signals and should be adjusted by C2 accurately. Q101, Q102, Q105, Q104 is charge circuitry. They are used to prevent OVER CURRENT and The Q104 is used to CHARGE DETECTOR. HAND SET. The signal which is inputted to MIC is transformed Analog into Digital at U100. DATA, which is transformed into Digital signal, is mixed with PN code at U100 (by spread spectrum) and transmitted to RF part. Spreading signal, which inputted to RF part, is mixed with Carrier supplied to VCO at U1 and create TX frequency of using channel and then is transmitted to ANTENNA through U3 by TX control of D1,D2 The signal received to antenna is transmitted to U100 by RX/TX control time. The signal inputted at U1 is mixed Carrier of VCO and got to direct conversion and create Base band signal. And then, create I and Q signal by demodulation (QPSK : Quadrature Phase Shift Keying method is phase- shifted by 90° ) I and Q signal (Two signal phase is 90°) is transmitted to U100 and remixed with PN code and generated Digital signal. This signal is transformed into Analog at U100. This audio signal is passed through R101,R102 and transmitted the RECEIVER unit. The Caller ID data which is received from Base is transformed to data which is able to display at U100. U100 activates LCD driver, and then, display caller ID messages. When the handset is low voltage R105, R106, C161 make the 77 pin of U100 change HIGH to LOW and indicate low voltage. Y101 is X-tal generating RF - reference signals and should be adjusted by C204 accurately. U102 is parts for voltage stabilization of CODEC part. Date : October 06, 2000 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 U.S.A. DIGITAL SECURITY CODE: The model(s) GT-8320Chas the circuitry for digital security code to provide protection against unintentional access. For each model, one of 16777216kinds of digital security code is randomly selected and fixed in each telephone as it is manufactured. D.S.KIM / Quality Engineering Dept. LG Electronics Inc. LG KangseoB/D 36, Munlae-Dong, 6-Ga, Youngdungpo-Gu, Seoul, 150-096, Korea Youngdungpo P.O Box101, Seoul, Korea Telephone : 82-2-2630-3651~2 Fax : 82-2-2630-361…

Text truncated - open the document above for the full version.