FIH05767LOCATION & MONITORING TRANSMITTER

General Installation Information Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an interior windshield-mounted tag from working correctly. If you have a vehicle with a metalized windshield, contact your local customer service center for more information. If your vehicle’s metalized windshield has a metal-free zone, it is typically located near the rearview mirror. Metal-Free Zone: Some vehicle metalized windshields have a metal-free zone. If your windshield has this zone, center the tag in that area and follow the installation instructions listed on this page. Tinted Windshields: Some vehicles have a metallic tint across the top of the windshield that might interfere with reading the tag. If your windshield has this metallic tint, install the tag at least 2 inches (5.1 cm) below the tinted area. Nonmetallic tint does not affect performance. Metal Sun Visors: Some vehicles have an exterior-mounted sun visor that might interfere with reading the tag. If your vehicle has this visor, mount the tag at least 2 inches (5.1 cm) below the visor. Required Supplies •GoAnywhere Pass •Optional suction-cup bracket (sold separately) •Commercial glass cleaner and paper towels GoAnywhere Pass Installation and Removal Procedures The GoAnywhere Pass may be mounted to the interior windshield with 3M™ Dual Lock™ strips, or with an optional bracket that attaches the tag to the windshield with suction cups. To install the Tag 1.Choose the location for your tag (Figure 1). The tag should be mounted approximately 1 inch (2.54 cm) below the rearview mirror post. Figure 1. Optimum Locations for Tag Performance 2.Clean and dry the interior windshield surface completely before affixing the fastener strips. The windshield temperature must be at least 68ºF (20ºC) for optimum bonding. Installation Instructions for the GoAnywhere Pass TM 16-8899-001 Rev X2 11/13 www.transcore.com ©2013 TransCore License, Ltd. All rights reserved. TRANSCORE is a registered trademark and EZGO ANYWHERE and GOANYWHERE PASS are trademarks and are used under license. All other trademarks are the property of their respective owners. Contents are subject to change. Printed in the U.S.A. SPECIFICATIONS 16-8899-001 Rev X2 11/13 3.Peel off the double-faced barrier on the Dual Lock strips (Figure 2). Apply the tag to the windshield using moderate pressure. Note: When installing the tag using Dual Lock strips for the first time, leave the tag in place for at least 24 hours to allow the adhesive to cure. Figure 2 Remove Backing to Expose Adhesive on Dual Lock Strips 4.If using the optional suction cup bracket, moisten the cups and press on the side tabs to stick the bracket to the windshield. 5.Holding the tag so that the arrow on the battery door points up, insert the tag into the bracket. You may also position the tag in the bracket as shown in Figure 3 and then mount it to the windshield. Figure 3 Correct Tag Orientation 6.To remove a tag mounted with Dual Lock strips from the windshield, grip the tag at the top and bottom sides. Gently lift the tag away from the windshield on one end until the tag is free from the windshield. Be careful not to hit the rearview mirror. NO UNAUTHORIZED MODIFICATIONS STATEMENT Caution: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment authorization from the FCC and will void the TransCore warranty. RADIO FREQUENCY INTERFERENCE STATEMENTS Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Note: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur del’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

December 17, 2013 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Transcore - Amtech Technology Center 8600 Jefferson Street NE Albuquerque, New Mexico 87113 Re: Confidentiality for submittal information regarding FCC ID number FIH05767 Product: Low Power Transmitter operating under parts 2 and 90M Dear Sirs: Transcore Amtech Technology Center requests that the material in the Parts List, Schematics, Block Diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. In support of this request, Transcore Amtech Technology Center submits the following information. CONFIDENTIAL FILES Block Diagram Conf BlkDia 05767.pdf Operational Description Conf OpDes 05767.pdf Schematics Conf Schem 05767.pdf Parts List Conf PartList 05767.pdf 1. Identification of the specific information for which confidential treatment is sought: The materials set forth in the Operational Description, block diagram, parts list, and Schematics, which are segregated, from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID No: FIH05767 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes a detailed theory of operation, circuit diagrams, and schematic. As such, this material is treated as highly confidential business information. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 4. Explanation of the degree to which the information concerns a service that is subject to competition: The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of Transcore Amtech Technology Center engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Transcore Amtech Technology Center. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by Transcore Amtech Technology Center and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry and standards groups as well as in rule making proceedings of the FCC, the protection sought is narrowly drawn and pertains to certain specific implementations of this radio technology. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure: This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. This equipment is designed for commercial, industrial, and governmental applications. As such, unlike most consumer equipment, this equipment could be used for more than a decade in some cases. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers

December 17, 2013 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Transcore - Amtech Technology Center Equipment: FCC ID: FIH05767 8600 Jefferson Street NE Albuquerque, New Mexico 87113 Re: Short-term Confidentiality request for submittal information regarding FCC ID: FIH05767 FCC Rules: Parts 2 and 90M Dear Sirs: Transcore - Amtech Technology Center requests that the following information be withheld from public disclosure pursuant to CFR47 paragraphs 0.457 and 0.459, and KDB 726920 until 45 days after the Grant of Equipment Authorization. Disclosure of information would offer competitors additional unwarranted insight into the state of the product development. Short-term confidential files Exhibit File External Photos Short Term Conf ExtPho 05767.pdf Internal Photos Short Term Conf IntPho 05767.pdf Test Setup Photos Short Term Conf TSup 05767.pdf User Manual Short Term Conf UserMan 05767.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053

December 17, 2013 Timco Engineering Inc. Federal Communications Commission 849 NW State Road 45 Equipment Approval Services Newberry, FL 32669 Pittsburgh, PA 15251-3315 Applicant: Transcore - Amtech Technology Center 8600 Jefferson Street NE Albuquerque, New Mexico 87113 Equipment: FCC ID: FIH05767 FCC Rules: Part 2 and 90M Sirs The form 731 and application have been electronically submitted and attachments up loaded to your site for use in processing for grant of certification. Confidentiality is requested as outlined below. Permanent Transcore Amtech Technology Center requests that the material in the Schematics, block diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. A statement of confidentiality will be attached with the application at the time of submittal. Block Diagram Conf BlkDia 05767.pdf Operational Description Conf OpDes 05767.pdf Schematics Conf Schem 05767.pdf Parts List Conf PartList 05767.pdf Short-term confidential files External Photos Short Term Conf ExtPho 05767.pdf Internal Photos Short Term Conf IntPho 05767.pdf Test Setup Photos Short Term Conf TSup 05767.pdf User Manual Short Term Conf UserMan 05767.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers Rogers Labs, Inc. Enclosures ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Telephone / Facsimile (913) 837-3214

Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: Short Term Conf ExtPho 05767 Page 1 of 2 Equipment photographs Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: Short Term Conf ExtPho 05767 Page 2 of 2

Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: LabelSmp 05767 Page 1 of 1 ID Label sample and Placement The full FCC statement is not printed due to the small size of the device. FCC and IC identification are consistent with other consumer products in this form factor.

Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: Short Term Conf IntPho 05767 Date: 12/17/2013 Internal photographs

1 Introduction The 05767 transmitter referred to herein is part of a multi-protocol Radio-Frequency Identification (RFID) transponder. The transmitter is battery-powered, microprocessor- controlled and communicates in the Inter-Agency Group (IAG) and ASTM V6 TDMA protocols. 2 Tune-Up Instructions The 05767 transmitter is manufactured with fixed components and no means for tuning are provided. Transmitters are 100% tested to ensure compliance.

Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: RFExp 05760 Page 1 of 1

NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Transcore Amtech Technology Center 4405 W. 259th Terrace Models: 05767 S/N: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 Parts 2, 90 and RSS-137 Date: December 18, 2013 Revision 1 File: Transcore 05767 90 TstRpt 131108 Page 1 of 27 Test Report CFR47 Part 90 and Industry Canada RSS-137 Application for Grant of Certification Model: 05767 Location and Monitoring Service Transmitter 902.25 - 903.75 and 911.75 – 919.75 MHz FCC ID: FIH05767 IC: 1584A-05767 FOR TRANSCORE AMTECH TECHNOLOGY CENTER 8600 Jefferson Street, NE Albuquerque, NM 87113 Report Number 131108 Authorized Signatory: Scot D. Rogers NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Transcore Amtech Technology Center 4405 W. 259th Terrace Models: 05767 S/N: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 Parts 2, 90 and RSS-137 Date: December 18, 2013 Revision 1 File: Transcore 05767 90 TstRpt 131108 Page 2 of 27 Test Report For Application of Certification For Transcore Amtech Technology Center 8600 Jefferson Street, NE Albuquerque, NM 87113 Phone: (505) 856-8101 Model: 05767 Location Monitoring Service Transmitter Frequency: 902.25 - 903.75 and 911.75 - 919.75 MHz FCC ID: FIH05767 IC: 1584A-05767 Test Date: February 10, 2013 Certifying Engineer: Scot D. Rogers Rogers Labs, Inc. 4405 W. 259th Terrace Louisburg, KS 66053 Telephone / Facsimile: (913) 837-3214 This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Transcore Amtech Technology Center 4405 W. 259th Terrace Models: 05767 S/N: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 Parts 2, 90 and RSS-137 Date: December 18, 2013 Revision 1 File: Transcore 05767 90 TstRpt 131108 Page 3 of 27 Table Of Contents TABLE OF CONTENTS .................................................................................................... 3 REVISION HISTORY ........................................................................................................ 4 EXECUTIVE SUMMARY .................................................................................................. 5 OPINION / INTERPRETATION OF RESULTS ................................................................. 5 APPLICATION FOR CERTIFICATION ............................................................................. 6 EQUIPMENT UNDER TEST ............................................................................................. 8 Equipment Configuration ........................................................................................................................................ 8 APPLICABLE STANDARDS AND TEST PROCEDURES ............................................... 9 UNITS OF MEASUREMENTS .......................................................................................... 9 TEST SITE LOCATIONS .................................................................................................. 9 ENVIRONMENTAL CONDITIONS.................................................................................... 9 LIST OF TEST EQUIPMENT ............................................................................................ 10 TRANSMITTER POWER OUTPUT .................................................................................. 11 Measurements Required .......................................................................................................................................... 11 Test Arrangement ..................................................................................................................................................... 11 Table 1 Transmitter Power Results ......................................................................................................................... 12 Figure 1 Power output ............................................................................................................................................ 12 MODULATION CHARACTERISTICS ............................................................................... 13 Measurements Required .......................................................................................................................................... 13 Test Arrangement ..................................................................................................................................................... 13 Results Modulation Characteristics ........................................................................................................................ 13 OCCUPIED BANDWIDTH ................................................................................................ 14 Measurements Required .......................................................................................................................................... 14 Test Arrangement ..................................................................................................................................................... 14 Table 2 Occupied Bandwidth Results ..................................................................................................................... 14 NVLAP Lab Code: 200087-0 Rogers Labs, Inc. Transcore Amtech Technology Center 4405 W. 259th Terrace Models: 05767 S/N: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 Parts 2, 90 and RSS-137 Date: December 18, 2013 Revision 1 File: Transcore 05767 90 TstRpt 131108 Page 4 of 27 Figure 2 Occupied Bandwidth ........…

Text truncated - open the document above for the full version.

Rogers Labs, Inc. Transcore - Amtech Technology Center 4405 W. 259th Terrace Model: 05767 SN: ENG1 FCC ID#: FIH05767 Louisburg, KS 66053 Test #: 131108 IC: 1584A-05767 Phone/Fax: (913) 837-3214 Test to: CFR47 90, RSS-137 Date: December 17, 2013 Revision 1 file: Short Term Conf TSup 05767 Page 1 of 1 Test setup photographs