FIHE4FPT90V1Location and Monitoring Service Interrogator

Encompass® 4 Flex Reader System Guide 16-XXXX-XXX Rev X1 6/21/2023 TransCore’s Encompass 4 Flex Reader System is a multi-protocol reader that reads TransCore Super eGo® (SeGo), eGo, American Trucking Associations/International Organization for Standardization (ATA/ISO), or Inter- Agency Group (IAG) tag protocols, and ISO 18000-6C (ePc). This guide provides site planning, installing, testing, and general operating instructions. This information is intended for use by authorized TransCore dealers, installers, and service personnel. Trusted Transportation Solutions Encompass 4 Flex Reader System Guide ii TransCore Proprietary © 2009-2021 TransCore, LP. All rights reserved. TRANSCORE, AMTECH, EGO, and ENCOMPASS are registered trademarks and are used under license. All other trademarks are the property of their respective owners. Contents are subject to change. Printed in the U.S.A. Information in this document is subject to change and does not represent a commitment on the part of TransCore, LP. For further information, contact: TransCore 8600 Jefferson Street NE Albuquerque, New Mexico 87113 USA TransCore Technical Support Web:www.transcore.com Phone: (505) 856-8007 iii TransCore Proprietary WARNING TO USERS IN THE UNITED STATES FEDERAL COMMUNICATIONS COMMISSION (FCC) LOCATION AND MONITORING SERVICE STATEMENT 47 CFR §90.351 NOTE: The user is required to obtain a Part 90 site license from the Federal Communications Commission (FCC) to operate this radio frequency identification (RFID) device in the United States. The FCC ID number is FIHE4FLEXV1. Access the FCC website at www.fcc.gov to obtain additional information concerning licensing requirements. NOTE: Users in all countries should check with the appropriate local authorities for licensing requirements. FCC RADIO FREQUENCY INTERFERENCE STATEMENT 47 CFR §15.105(A) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate RF energy and may cause harmful interference to radio communications if not installed and used in accordance with the instruction manual. Operating this equipment in a residential area is likely to cause harmful interference, in which case, depending on the laws in effect, the user may be required to correct the interference at their own expense. NO UNAUTHORIZED MODIFICATIONS 47 CFR §15.21 CAUTION: This equipment may not be modified, altered, or changed in any way without permission. Unauthorized modification may void the equipment authorization from the FCC and will void the warranty. USE OF SHIELDED CABLES AND GROUNDING 47 CFR §15.27(A) NOTE: Shielded cables for communications lines and earth grounding the unit is recommended for this equipment to comply with FCC regulations. TRANSCORE, LP USA Encompass 4 Flex Reader System Guide iv TransCore Proprietary AVERTISSEMENT À L’ATTENTION DES UTILISATEURS AUX ÉTATS-UNIS DÉCLARATION 47 CFR §90.351 (CODE DES RÈGLEMENTS FÉDÉRAUX) DE LA FEDERAL COMMUNICATIONS COMMISSION (FCC) SUR LES SERVICES DE LOCALISATION ET DE CONTRÔLE REMARQUE : L’utilisateur est tenu d’obtenir une licence d’utilisation sur site Partie 90 auprès de la Federal Communications Commission (FCC) afin de pouvoir utiliser ce dispositif RFID (radio- identification) aux États-Unis ou au Canada. Le numéro d’identification de la FCC est FIHE4FLEXV1. Pour obtenir de plus amples informations concernant les exigences relatives aux licences, prière de consulter le site web de la FCC à www.fcc.gov. REMARQUE : Il est recommandé à tous les utilisateurs, quel que soit leur pays, de consulter les autorités locales compétentes sur les exigences de licence. DÉCLARATION 47 CFR §15.105(A) DE LA FCC SUR LES INTERFÉRENCES DES FRÉQUENCES RADIO REMARQUE : Cet appareil a été testé et déclaré conforme à la catégorie d’un appareil numérique de classe A en accord avec la partie 15 des directives de la FCC. Ces normes visent à assurer une protection raisonnable contre les interférences nuisibles lorsque l’appareil est utilisé dans un environnement commercial. Cet appareil génère, utilise et peut émettre de l’énergie RF et peut être à l’origine d’interférences nuisibles aux communications radio s’il n’est pas installé et utilisé en suivant les directives du manuel d’instructions. Si cet appareil est utilisé dans une zone résidentielle, il est probable qu’il cause des interférences nuisibles. Dans ce cas, l’utilisateur pourrait être amené à remédier aux interférences à ses propres frais, selon les lois du pays en vigueur. AUCUNE MODIFICATION NON AUTORISÉE 47 CFR §15.21 MISE EN GARDE : Il est interdit de modifier, d’altérer ou d’apporter des changements à cet appareil de quelque manière que ce soit sans autorisation. Toute modification non autorisée peut annuler l’autorisation d’utilisation accordée par la FCC et annulera la garantie. UTILISATION DE CÂBLES BLINDÉS ET MISE À LA TERRE 47 CFR §15.27(A) REMARQUE : Il est recommandé d’utiliser des câbles blindés et une mise à la terre avec cet appareil afin de répondre aux réglementations de la FCC TRANSCORE, LP ÉTATS-UNIS v TransCore Proprietary WARNING TO USERS IN CANADA INDUSTRY CANADA (IC) INDUSTRY CANADA’S RADIO STANDARD SPECIFICATIONS (RSS-137) LOCATION AND MONITORING SERVICE IN THE BAND 902-928 MHZ SECTION 2.1 NOTE: The user is required to obtain a license from Industry Canada (IC), to operate this radio frequency identification (RFID) device in Canada. The IC ID number is 1584A-E4FRSS137V1 access the IC website at www.ic.gc.ca to obtain additional information concerning licensing requirements. Industry Canada (IC) Industry Canada’s Radio Standard Specifications General Requirements (RSS- GEN) for Compliance of Radio Apparatus Statement Section 8.4 This device complies with Industry Canada’s license-exempt RSSs. Operati…

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 30, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: FIHE4FPT90V1 TransCore (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of it subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Dale Scott VP Engineering TransCore | 8600 Jefferson St. NE | Albuquerque, NM 87113 Office: 505 856 8066

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 30, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: FIHE4FPT90V1 TransCore (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Dale Scott VP Engineering TransCore | 8600 Jefferson St. NE | Albuquerque, NM 87113 Office: 505 856 8066

August 8, 2023 Timco Engineering Inc. Federal Communications Commission 849 NW State Road 45 Equipment Approval Services Newberry, FL 32669 Pittsburgh, PA 15251-3315 Applicant: Transcore - Amtech Technology Center 8600 Jefferson Street NE Albuquerque, New Mexico 87113 Equipment: FCC ID: FIHE4FPT90V1 FCC Rules: Part 2, 90M Sirs The 731 Form and application have been electronically submitted and attachments uploaded to your site for use in processing for grant of certification. Confidentiality is requested as outlined below. Permanent Transcore Amtech Technology Center requests that the material in the Block Diagram, Operational Description, Parts List, Schematics, and Tune Procedure be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. A statement of confidentiality will be attached with the application at the time of submittal. CONFIDENTIAL FILES Block Diagram E4FLEXV1 Conf BlkDia.pdf Operational Description E4FLEXV1 Conf OpDes.pdf Parts List E4FLEXV1 Conf PartsList.pdf Schematics E4FLEXV1 Conf Schem.pdf Tune Procedure E4FLEXV1 Conf TunPro.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers Rogers Labs, Inc. Enclosures ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Telephone / Facsimile (913) 837-3214

August 8, 2023 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Transcore - Amtech Technology Center 8600 Jefferson Street NE Albuquerque, New Mexico 87113 Re: Confidentiality request for FCC ID: FIHE4FPT90V1 Dear Sirs: Transcore Amtech Technology Center requests that the material in the Block Diagram, Operational Description, Parts Lists, Schematics, and Tune Procedure be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. In support of this request, Transcore Amtech Technology Center submits the following information. CONFIDENTIAL FILES Block Diagram E4FLEXV1 Conf BlkDia.pdf Operational Description E4FLEXV1 Conf OpDes.pdf Parts List E4FLEXV1 Conf PartsList.pdf Schematics E4FLEXV1 Conf Schem.pdf Tune Procedure E4FLEXV1 Conf TunPro.pdf 1. Identification of the specific information for which confidential treatment is sought: The materials set forth in the Block Diagram, Operational Description, Parts List, Schematics, and Tune Procedure which are segregated, from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID: FIHE4FPT90V1 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes Block Diagram, Operational Description, Parts List, Schematics, and Tune Procedure. As such, this material is treated as highly confidential business information. 4. Explanation of the degree to which the information concerns a service that is subject to competition: ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of Transcore Amtech Technology Center engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Transcore Amtech Technology Center. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by Transcore Amtech Technology Center and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry and standards groups as well as in rule making proceedings of the FCC, the protection sought is narrowly drawn and pertains to certain specific implementations of this radio technology. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure: This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. This equipment is designed for commercial, industrial, and governmental applications. As such, unlike most consumer equipment, this equipment could be used for more than a decade in some cases. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers

Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 9, 2023 Revision 1 File: E4FLEXV1 ExtPho Page 1 of 3 Equipment photographs Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 9, 2023 Revision 1 File: E4FLEXV1 ExtPho Page 2 of 3 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 9, 2023 Revision 1 File: E4FLEXV1 ExtPho Page 3 of 3

A A 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 AA BB CC DD VIEW A-A SCALE 1 : 1 DETAIL B SCALE 3 : 1 B 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 AA BB CC DD

Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 1 of 6 Internal photographs Transmitter PCB Primary Side shielding removed Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 2 of 6 Transmitter PCB Secondary Side Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 3 of 6 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 4 of 6 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 5 of 6 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 IntPho Page 6 of 6

Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 30, 2023 Revision 1 File: E4FLEXV1 RFExp Page 1 of 1 HVIN:E4FLEXV1Test Number:230613 MPE CalculatorRF Exposure uses EIRP for calculation. EIRP is based on TX power added to the antenna gain in dBi. dBi = dB gain compared to an isotropic radiator. S = p o we r d e ns ity in mW /c m^ 2 Transmitter Output power (mW)2133.0 Transmitter Output power (W)2.13 Output Power for % duty Cycle operation (Watts)1002.13Antenna Gain (dBi)10.3 Output Power for 100% duty Cycle operation (Watts)2.13Antenna Gain (N umeric)10.72 Tx Frequency (MHz)902 Calculation power (Watts)2.13dBd + 2.17 = dBidBi to dBd2.17 Antenna Gain (dBd)8.13 Cable Loss (dB)0.0Adjusted Power (dBm)33.29Antenna minus cable (dBi)10.30 Antenna Gain (N umeric)10.72 Calculated ERP (mw)13867.558EIRP = Po(dBm) + Gain (dB) Calculated EIRP (mw)22855.988Radiated (EIRP) dBm43.590 ERP = EIRP - 2.17 dB Radiated (ERP) dBm41.420 Occupational Limit 3.006666667 mW/cm 2 Frequency (MHz) O c c up a tio na l Limit (mW /c m 2 )P ub lic Limit (mW /c m 2 ) 30.1 W/m 2 30-30010.2 Ge ne ral Public Limit300-1,500f/300f/1500 0.601333333 mW/cm 2 1,500-10,00051 6.0 W/m 2 Occupational Limit 0.6455ƒ 0.5 W/m 2 19.4 W/m 2 Frequency (MHz) O c c up a tio na l Limit (W /m 2 )P ub lic Limit (W /m 2 ) Ge ne ral Public Limit100-6,000 0.6455ƒ 0.5 0.02619ƒ 0.6834 W/m 2 6,000-15,00050 2.74 W/m 2 48-3001.291 300-6,000 0.02619ƒ 0.6834 6,000-15,0005010 Ge ne ra l P ub licOccupational f = Trans mit Frequency (MHz) f (MHz) =902902MHz P T = Power Input to Antenna (mW) P T (mW) = 2,133.04492,133.0449 mW Duty cycle (percentage of operation) % =100100% P A = Adjusted Power due to Duty cycle or Cable Loss (mW) P A (mW) = 2,133.042,133.04 mW G N = Numeric Gain of the Antenna GN (numeric) =10.7210.72nume ric S 20 = Power Density of device at 20cm (mW/m 2 ) S 20 =(P A G N )/(4πR 20 ) 2 S 20 (mW /m 2 ) = 4.554.55 mW /m 2 S 20 = Power Density of device at 20cm (W/m 2 ) S 20 =(P A G N )/(4πR 20 ) 2 S 20 (W/m 2 ) = 45.4745.47 W/m 2 S L = Po wer Den s it y Limit (W / m 2 ) FCC S L (W/m 2 )= 6.01330.067 W/m 2 S L = Po wer Den s it y Limit (W / m 2 ) Canada S L (W/m 2 )= 2.74019.387 W/m 2 R C = Minimum distance to the Radiating Element for Compliance (cm) FCC R C =√(P A G N /4πS L )R C (cm) =55.024.6cm R C = Minimum distance to the Radiating Element for Compliance (cm) Canada R C =√(P A G N /4π S L )R C (cm) =81.530.6cm S C = Power Density of the device at the Compliance Distance R C (W /m 2 ) FCC S C =(P A G N )/(4πR C ) 2 S C (W/m 2 ) = 6.0130.07 W/m 2 S C = Power Density of the device at the Compliance Distance R C (W /m 2 ) Canada S C =(P A G N )/(4πR C ) 2 S C (W/m 2 ) = 2.7419.39 W/m 2 R 20 = 20cm R20=2020cm For Compliance with Canada General Population Limits, User Manual must indicate a minimum separation distance of 81.5cm Or in Meters for Compliance with Canada General Population Limits, a minimum separation distance of 0.81Meters S umma ry: S ta nd a lo ne M P E C a lc ula tio ns a nd S umma ryP ub lic LimitP ub lic Tx Duty C ycle (%)Tx Frequency (MHz)Power Total (mW)Antenna Gain (numeric) S L (W/m 2 )S 20 (W/m 2 ) R C (c m) S C (W/m 2 ) FCC1009022,13310.726.01345.4755.06.01 Canada1009022,13310.722.74045.4781.52.74 O ve ra ll M inimum (c m)O ve ra ll M inimum (inc he s ) P ub licOccupational FCC (cm)55.024.6 FC C (inches)22.010.0 Canada (cm)81.530.6 Canada (inches)33.013.0 82cm31cm 33inches13inches FCC radio frequency radiation exposure limits per 1.1310 IC radio frequency radiation exposure limits per RSS-102 Limit O ve ra ll M inimum Limit P ub licO ve ra ll M inumu Limit O c c up p a tio na l EIRP Power density (S) mW/cm 2 =------- 4 pr^2 r (cm) EIRP (mW)

NVLAP Lab Code 200087-0 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 1, 2023 Revision 1 File: Transcore E4FLEXV1 TstRpt 230613 Page 1 of 58 Engineering Test Report for Grant of Certification of Application 47CFR Part 90 and Industry Canada RSS-137 Location and Monitoring Service Transmitter HVIN: E4FLEXV1 902.25-903.75 and 910.00-921.50 MHz FCC ID: FIHE4FPT90V1 IC: 1584A-E4FRSS137V1 Transcore Amtech Technology Center 8600 Jefferson Street, NE Albuquerque, NM 87113 FCC Designation: US5305 ISED Registration: 3041A-1 Test Report Number: 230613 Test Date: June13through July 20, 2023 Authorized Signatory: Scot D. Rogers This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 1, 2023 Revision 1 File: Transcore E4FLEXV1 TstRpt 230613 Page 2 of 58 Table of Cont ents Table of Contents TABLE OF CONTENTS .................................................................................................. 2 REVISION HISTORY ...................................................................................................... 4 EXECUTIVE SUMMARY ................................................................................................ 5 SUMMARY ...................................................................................................................... 5 ATTESTATIONS ............................................................................................................. 5 APPLICABLE STANDARDS AND TEST PROCEDURES ............................................. 6 OPINION / INTERPRETATION OF RESULTS ............................................................... 6 EQUIPMENT UNDER TEST ........................................................................................... 7 Equipment Function ............................................................................................................................................... 7 Equipment Configuration ...................................................................................................................................... 8 APPLICATION FOR CERTIFICATION ........................................................................... 9 UNITS OF MEASUREMENTS ...................................................................................... 12 TEST SITE LOCATIONS .............................................................................................. 12 ENVIRONMENTAL CONDITIONS................................................................................ 12 TEST #1 TRANSMITTER POWER OUTPUT ............................................................... 13 Measurements Required ...................................................................................................................................... 13 Test Arrangement Output Power ........................................................................................................................ 13 Table 1 Transmitter Power Results ..................................................................................................................... 14 Figure 1 Transmitter Output Across Frequency Band CW (ATA) High Power Level 902-904 MHz band ...... 15 Figure 2 Transmitter Output Across Frequency Band CW (ATA) High Power Level 910-921.75 MHz band . 16 Figure 3 Transmitter Output Across Frequency Band CW (ATA) Lowest Power Level 902-904 MHz band .. 17 Figure 4 Transmitter Output Across Frequency Band CW (ATA) Lowest Power Level 910-921.75 MHz band ............................................................................................................................................................................ 18 Figure 5 Transmitter Output Across Frequency Band eGo ................................................................................ 19 Figure 6 Transmitter Output Across Frequency Band SeGo .............................................................................. 20 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 1, 2023 Revision 1 File: Transcore E4FLEXV1 TstRpt 230613 Page 3 of 58 Figure 7 Transmitter Output Across Frequency Band IAG ............................................................................... 21 Figure 8 Transmitter Output Across Frequency Band EPC ............................................................................... 22 TEST #2 MODULATION CHARACTERISTICS ............................................................ 23 Measurements Required ...................................................................................................................................... 23 Test Arrangement ................................................................................................................................................. 23 TEST #3 OCCUPIED BANDWIDTH ............................................................................. 24 Measurements Required ...................................................................................................................................... 24 Test Arrangement ..........…

Text truncated - open the document above for the full version.

Page 1 of 3 8/28/2023 Antenna Report 1 General Information The E4H use an internal antenna with a peak gain of 10.3 dBi (reference Figure 1 for plot). The test for the antenna patterns were performed at Sierra Wireless using there anechoic OTA chamber test range. The data that plot was taken from the data in the attached excel spread sheet (attachment 1). Figure 1. Gain of Internal Antenna 915 E4 Antenna Pattern Data.xlsx Attachment 1. Antenna Pattern Data -30 -25 -20 -15 -10 -5 0 5 10 15 -180 -174 -168 -162 -156 -150 -144 -138 -132 -126 -120 -114 -108 -102 -96 -90 -84 -78 -72 -66 -60 -54 -48 -42 -36 -30 -24 -18 -12 -6 0 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 156 162 168 174 180 E-Plane H-Plane Peak gain=10.3 dBi BW E ~ 51 o BW H ~ 48 o Page 2 of 3 8/28/2023 2 Equipment List The following equipment was used: Equipment Used Description RF Signal Generator Used to excite the Antenna Under Test (AUT) RF Signal Analyzer Used to measure the power level from the AUT Measurement Antenna Used to with the RF Signal Analyzer to collect the RF signal from the excited AUT. Multi-Axis Positioner Used to position the AUT in the X, Y, and Z axis. 3 Test Chamber & Set up pictures Photo 1. AUT Mounting X Y Z Reference Page 3 of 3 8/28/2023 Photo 2. Antenna Mounting on Multi Axis Positioner Diagram 1. AUT Test Chamber Setup 4 Engineer Contact The following engineer is the contact person for the content of this report. ______________________________________ Michael P. Gonzales | Analog/RF/DSP Design Engineer TransCore | 8600 Jefferson St. NE | Albuquerque, NM 87113 Office: 505 856 8022 Email: [email protected].

Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 8, 2023 Revision 1 File: E4FLEXV1 TSup Page 1 of 5 Test setup photographs Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 8, 2023 Revision 1 File: E4FLEXV1 TSup Page 2 of 5 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 8, 2023 Revision 1 File: E4FLEXV1 TSup Page 3 of 5 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 8, 2023 Revision 1 File: E4FLEXV1 TSup Page 4 of 5 Rogers Labs, Inc. Transcore PMN: E4 FLEX SN: Sample 1 4405 West 259 th Terrace HVIN: E4FLEXV1 FCC ID: FIHE4FPT90V1 Louisburg, KS 66053 Test: 230613 IC: 1584A-E4FRSS137V1 Phone/Fax: (913) 837-3214 Test to: 47CFR Parts 2, 90 and RSS-137 Date: August 8, 2023 Revision 1 File: E4FLEXV1 TSup Page 5 of 5