GKRT0022100802.11/b WLAN Module Build In Tablet PC

MOTION COMPUTING M1200 AND M1300 TABLET PC USER GUIDE Motion Computing M1200 and M1300 Tablet PC User Guide ii Copyright Information Acrobat is a registered trademark of Adobe Systems Incorporated. Microsoft Windows, Windows XP, Windows XP Tablet PC Edition, and Windows Journal are either registered trademarks or trademarks of Microsoft Corporation in the United States and/ or other countries. O 2 Micro is a trademark of O 2 Micro International Limited. Realtek is a trademark of Realtek Semiconductor Corporation. Intel and Pentium are registered trademarks and Centrino is a trademarks of Intel Corporation. PCTEL is a registered trademark of PCTEL, Inc. Phoenix is a trademark and FirstBIOS is a common law trademark of Phoenix Technologies, Ltd; Sigmatel is a registered trademark of Sigmatel Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Motion Computing, Inc. has made every effort to identify trademarked properties and owners on this page. All other trademarks are properties of their respective owners. NOTICE: The information in this publication is subject to change without notice. MOTION COMPUTING, INC. SHALL NOT BE HELD LIABLE FOR TECHNICAL, OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR ACCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. This publication contains information protected by copyright. No part of this publication may be photocopied or reproduced in any form without prior written consent from Motion Computing, Inc. © 2003 Motion Computing, Inc. Motion Computing, the Motion logo, Registered, U.S. Patent and Trademark Office (May 2003) P/N 024-02-0016 A06 Motion Computing M1200 and M1300 Tablet PC User Guide iii About This User Guide CAUTIONS, WARNINGS AND NOTICES The following notices are found in this User Guide: WARNING: Text set off in this way indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this way indicates that failure to follow directions in the Caution could result in damage to the equipment or loss of information. IMPORTANT: Text set off in this way presents information or instructions that should be followed or information of particular interest. NOTE: Text set off in this way presents information or instructions. MENU ITEMS, BUTTONS, ICONS Menu items, icons, and instructions found in the procedures in this User Guide are set apart by capitalizing them exactly as shown on screen. For example, the Start menu, Dashboard, Tablet and Pen Settings icon, Apply, Reset, etc. Buttons on the chassis are identified through diagrams. W RITING ON THE DISPLAY References to writing on the Tablet PC display in this User Guide mean any hand-written input using the specially-designed Motion M-Series Pen, provided. The display responds only to this Motion Pen and not to any other type of Pen or to a stylus or other device used with Personal Digital Assistants (PDAs). The display surface may be damaged by ink pens or other pointed objects. I NKReference to ink in the documentation means text entered in handwritten format and converted to an object that can be displayed exactly as you write it. R EFERENCES TO USING THE P EN AND P EN FUNCTION B UTTON Notations for using the Motion M-Series Pen, which are found throughout this User Guide, are described below: • Tap — Tap the Pen on the Tablet PC display, without pressing the function button on the Pen • Double-tap — Double-tap the Pen on the display, without pressing the function button on the Pen • Right-click — Press the function button on the Pen and tap the Pen on the display (equivalent to a mouse right-click) • Press and hold — Press and hold the tip of the Pen to the display, without pressing the function button on the Pen (equivalent to a mouse right-click) • Tap and drag — Tap and drag the Pen on the display • Select/Highlight — Tap on the item on the Tablet PC display with the Pen to activate the function Motion Computing M1200 and M1300 Tablet PC User Guide iv Chapter 1 Getting Started with Motion M1200 and M1300 Tablet PCs Motion Computing M1200 and M1300 Tablet PC User Guide 1 Chapter 1 Getting Started with Motion M1200 and M1300 Tablet PCs Thank you for deciding to purchase a Motion M1200 or M1300 Tablet PC from Motion Computing TM ! Motion Tablet PCs combine the best features of desktop computing and notebooks with more power than any touchscreen or personal digital assistant (PDA) can provide. MOTION M1200 AND M1300 F EATURES The Motion M1200 Tablet PC offers these unique features: •Intel® Pentium® M processor (833MHz ULV) •IEEE 802.11b wireless LAN mini-PCI card capability •USB 1.1 The Motion M1300 Tablet PC offers these unique features: •Intel® Centrino TM mobile technology, which includes: • Intel Pentium M processor (900MHz ULV) • Intel 855 chipset family • Intel PRO 2100 wireless network connection that supports IEEE 802.11b; Wi-Fi TM compliant •USB 2.0 Both Motion M1200 and M1300 Tablet PCs offer these standard features: •Microsoft® Windows® XP Tablet PC Edition operating system •12.1-inch XGA TFT LCD display Chapter 1 Getting Started with Motion M1200 and M1300 Tablet PCs Motion Computing M1200 and M1300 Tablet PC User Guide 2 •M-Series Digitizer Pen •256MB base RAM, upgradeable to 1GB; minimum 20GB hard drive •Front panel status LEDs •Front panel function Buttons •Motion Dashboard for easy access to Tablet PC functions •Screen rotation; handwriting and drawing recognition; voice recognition software; dual-head video controller •Power switch On/Off; with Stand By and Hibernate modes •AC Power Adapter and power cord •I/O: Microphone in; Headphone out; DC power in; two USB ports; IEEE 1394 port; external VGA monitor port; RJ-11 (modem); RJ-45 (Ethernet network) •Pen storage slot and Pen tether anchor on the Tablet PC chassis •PC card slot, for networking, memory expansion or accessory connec- tions •USB keyboard and mouse support •6-cell, prismatic Lith…

Text truncated - open the document above for the full version.

Figure 1: Detailed Block Diagram for the Intel® PRO/Wireless LAN 2100 miniPCI adapter (Red items are on back side of PCB) 82531ME BBP MAC miniPCI SA2400 2.45GHz Direct Conversion Radio 40 MHz 22 MHz CCK BBP Differential I and Q MAX2242 RF PA 2.4-2.5GHz LOW PASS FILTER DP2T RF SWITCH 2.45GHz BANDPASS FILTER LNA 6dB PAD 6dB PAD 2.45GHz BANDPASS FILTER BALUN BALUN EEPROM ISOLATOR Rx Tx LOW PASS FILTER 1.8VA 1.8VD 3.3V 3.3VA 1.8VD 3.3V 2.9VA 3.3VA 3.3VA 3.3V 2.9VA J5 J6 A A B B C C D D E E 11 22 33 44 Title SizeDocument NumberRev Date:Sheet of BMX01 LA-1751 0.2 BLOCK DIAGRAM Compal Electronics, Inc. 230Wednesday, February 12, 2003 PCI BUS LPC BUS Clock Generator USB2.0 conn X3 uFCBGA CPU CardBus CTRL Montara-GM GMCH-M HUB Link HD#(0..63) 4XHA#(3..31) 2X Model Name :BMX01 AMPIFIER page 3,4 page 14 page 16 page 10 page 5,6,7 File Name : LA-1751 Banias ULV Block Diagram Power Circuit DC/DC page 24,25,26,27,28,29,30 Slot 0 page 16 PIDE AC97 Codec PSB ICH4-M OZ6912T Memory BUS CPU Bypass & CPUVID page 4 1.05V 100MHz 1.5VS 66MHz 4X 3.3V 33MHz 2.5V 200/266MHz 3.3V 48MHz 3.3V 24.576MHz 3.3V ATA100 3.3V 33MHz MDC page 3 732 BGA 421 BGA page 11,12,13,15 SO-DIMM X2 BANK 0, 1, 2, 3 page 8,9 Thermal Sensor ADM1032AR Cy28346 page 3 ALC202 IDSEL:AD20 (PIRQB#,GNT#2,REQ#2) AC-LINK ITP Conn THIS SHEET OF ENGINEERING DRAWING IS THE PROPRIETARY PROPERTY OF COMPAL ELECTRONICS, INC. AND CONTAINS CONFIDENTIAL AND TRADE SECRET INFORMATION. THIS SHEET MAY NOT BE TRANSFERRED FROM THE CUSTODY OF THE COMPETENT DIVISION OF R&D DEPARTMENT EXCEPT AS AUTHORIZED BY COMPAL ELECTRONICS, INC. NEITHER THIS SHEET NOR THE INFORMATION IT CONTAINS MAY BE USED BY OR DISCLOSED TO ANY THIRD PARTY WITHOUT PRIOR WRITTEN CONSENT OF COMPAL ELECTRONICS, INC. PROPRIETARY NOTE Mini PCI page 18 IDSEL:AD18 (PIRQC/D#,GNT#1,REQ#1) I/O Conn. 140P page 17 (PIRQA/C#,GNT#&REQ#0/3) LPC Super I/O NS PC87391EC 87591S page 21 page 19 SST39VF080-70 CRT Conn RJ-11 MIC HP OUT IEEE 1394 IDSEL:AD16 (PIRQA#,GNT#0,REQ#0) page 23 page 22 Power On/Off & LED & RTC DC/DC Interface Suspend Compal confidential Note: Symbol" " stand for in the I/O Board, page 18 page 15 +CPU_CORE +VCCP +3VS->+3V_CLK +3VS->+3VS_CLKVDD +3VS->+3VS_VDD48K +5VS +5VS +3VS +3VALW +1.5VS +VCC_RTC->+RTCVCC +2.5V +1.2VS +1.5VS +VCCP +3VS +3VALW +3V->+3VS_MINIPCI +5VS->+5VS_MINIPCI +3VALW->+3.3AUX +5VS +5V->+5VMDC +3V->+3VMDC LCD Conn. LVDS I/F +3VS->LCDVDD +3VALW +3VS +3VALW->EC_AVCC +RTCVCC page 21 EC I/O Buffer DATAIN0 DATAIN1 " " for wire-set Slot 0 Slot 1 to dock RTL8100BL LAN Ctrl SN74HCT273PW BIOS IDSEL: AD23 (PIRQC#,GNT#3,REQ#3) Digitizer COM1 page 20 SN74HCT244PW

Compal Electronics, Inc. Mar. 20, 2002 Federal Communications Commission Authorization and Evaluation Division FCC ID: GKRT0022100 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1. 1. Schematics 2. 2. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, (Singer Name) / (Title) Compal Electronics, Inc.

C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 44 Rev. 00 Front View of EUT Back View of EUT C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 45 Rev. 00 Left View of Notebook Right View of Notebook C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 46 Rev. 00 Top View of Notebook Bottom View of Notebook C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 47 Rev. 00 Front View of Adaptor Back View of Adaptor

FCC ID LABEL FORMAT AND LOCATION Applicant: Compal Electronics, Inc. FCC ID: GKRT0022100 FCC ID: GKRT0022100 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 48 Rev. 00 Internal of Notebook –1 Internal of Notebook –2 C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 49 Rev. 00 Internal of Notebook –3 Internal of RF Module –4 RF Modul e Antenna Antenna Bottom Cover C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 50 Rev. 00 Internal of RF Module –5 Internal of RF Module –6 C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 51 Rev. 00 Internal of RF Module –7 Internal of RF Module –8

in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for Wireless LAN Module Build in Tablet PC Trade Name: Motion Tablet M1300 Model: T002 FCC ID: GKRT0022100 April 9, 2003 REPORT NO: 03T1915-1 Prepared for Compal Electronics, Inc. No. 581, Juikuang Road Neihu, Taipei (114), Taiwan, R. O. C. Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 REPORT NO: 03T1915-1 DATE: April 9, 2003 FCC ID: GKRT0022100 COMPLIANCE CERTIFICATION SERVICES Page 2 of 22 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: April 7 & 9, 2003 Report No: 03T1915-1 APPLICANT: Compal Electronics, Inc. No. 581, Juikuang Road Neihu, Taipei (114), Taiwan, R. O. C. MODEL: T002 FCC ID: GKRT0022100 DEVICE CATEGORY: PORTABLE DEVICES EXPOSURE CATEGORY: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: Direct Sequence Spread Spectrum (DSSS) Operating mode: Maximum continuous output Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: 16.82 dBm (Conducted) Max. SAR (1g): 0.355 mW/g Application type: Certification FCC Rule part(s): § 15.247 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Steve Cheng EMC Engineering Manager REPORT NO: 03T1915-1 DATE: April 9, 2003 FCC ID: GKRT0022100 COMPLIANCE CERTIFICATION SERVICES Page 3 of 22 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENT 1. EUT DESCRIPTION........................................................................................................4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC.................5 3. DOSIMETRIC ASSESSMENT SYSTEM........................................................................5 3.1. MEASUREMENT SYSTEM DIAGRAM.......................................................................................................6 3.2. SYSTEM COMPONENTS..............................................................................................................................7 4. EVALUATION PROCEDURE..........................................................................................9 5. MEASUREMENT UNCERTAINTY................................................................................12 6. EXPOSURE LIMIT.........................................................................................................13 7. MEASUREMENT RESULTS.........................................................................................14 7.1. SYSTEM VALIDATION.................................................................................................................................14 7.2. TEST LIQUID CONFIRMATION.................................................................................................................15 7.3. EUT TUNE-UP PROCEDURES..................................................................................................................15 7.4. EUT SETUP PHOTOS.................................................................................................................................16 7.5. SAR MEASUREMENT RESULTS..............................................................................................................17 8. EUT PHOTOS................................................................................................................18 9. EQUIPMENTS LIST & CALIBRATION STATUS.........................................................20 10. REFERENCES...............................................................................................................21 11. ATTACHMENTS............................................................................................................22 REPORT NO: 03T1915-1 DATE: April 9, 2003 FCC ID: GKRT0022100 COMPLIANCE CERTIFICATION SERVICES Page 4 of 22 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. EUT DESCRIPTION APPLICANT: Compal Electronics, Inc. No. 581, Juikuang Road Neihu, Taipei (114), Taiwan, R. O. C. MODEL: T002 FCC ID: GKRT0022100 DEVICE CATEGORY: PORTABLE DEVICES EXPOSURE CATEGORY: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: Direct Sequence Spread Spectrum (DSSS) Operating mode: Maximum continuous output Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: 16.82 dBm (Conducted) Max. SAR (1g): 0.355 mW/g Application type: Certification FCC Rule part(s): § 15.247 Wireless Module: LAN Mini-PCI Type 3B Adapter Manufactured by Intel, model WM3B 2100 Antenna (s): TX Antenna (Top side) – Type PIFA 1 Specific Absorption Rate (SAR) is a measure of the rate of energy absorption due to exposure to an RF transmitting source (wireless portable device). 2 IEEE/ANSI Std. C95.1-1992 limits are used to determine compliance …

Text truncated - open the document above for the full version.

Date/Time: 04/07/03 18:43:32 Test Laboratory: Compliance Certification Services File Name: D2450V2 SN 706_13.1 mW.da4 DUT: Dipole Type & Serial Number: D2450V2 SN 706 Program: System Validation (ET3DV6 SN 1577); I/P Power 250 mW, Air temp. 25 deg C, liquid temp. 23 deg C Communication System: CW - 2450 MHz; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium: Head 2450 MHz ( σ = 1.8809 mho/m, ε = 39.9, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(5.1, 5.1, 5.1); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 93.6 V/m Peak SAR = 28.3 mW/g SAR(1 g) = 13.1 mW/g; SAR(10 g) = 5.81 mW/g Power Drift = -0.05 dB Area Scan (9x9x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -22.9 -20.6 -18.3 -16 -13.7 -11.4 -9.15 -6.86 -4.57 -2.29 0 Date/Time: 04/09/03 19:05:50 Test Laboratory: Compliance Certification Services File Name: D2450V2 SN 706_12.9 mW.da4 DUT: Dipole Type & Serial Number: D2450V2 SN 706 Program: System Validation (ET3DV6 SN 1577); I/P Power 250 mW, Air temp. 24 deg C, liquid temp. 23 deg C Communication System: CW - 2450 MHz; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium: Head 2450 MHz ( σ = 1.87 mho/m, ε = 40.16, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(5.1, 5.1, 5.1); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 93.9 V/m Peak SAR = 27.5 mW/g SAR(1 g) = 12.9 mW/g; SAR(10 g) = 5.79 mW/g Power Drift = -0.02 dB Area Scan (9x9x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -22.5 -20.3 -18 -15.8 -13.5 -11.3 -9.01 -6.76 -4.5 -2.25 0

Date/Time: 04/07/03 21:30:30 Test Laboratory: Compliance Certification Services File Name: 1L-CH_0.212 mW.da4 EUT Setup Configuration 1 SAR in dB -14.1 -12.6 -11.2 -9.84 -8.43 -7.03 -5.62 -4.22 -2.81 -1.41 0 Date/Time: 04/07/03 21:30:30 Test Laboratory: Compliance Certification Services File Name: 1L-CH_0.212 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 1; Air temp 25 deg C & Liquid temp 22.7 deg C Communication System: DSSS; Frequency: 2412 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9368 mho/m, ε = 50.84, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 2.72 V/m Peak SAR = 0.621 mW/g SAR(1 g) = 0.212 mW/g; SAR(10 g) = 0.0886 mW/g Power Drift = -0.12 dB Area Scan (13x27x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -14.1 -12.6 -11.2 -9.84 -8.43 -7.03 -5.62 -4.22 -2.81 -1.41 0 Date/Time: 04/07/03 22:39:46 Test Laboratory: Compliance Certification Services File Name: 2M-CH_0.165 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 1; Air temp 25 deg C & Liquid temp 22.6 deg C Communication System: DSSS; Frequency: 2437 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9368 mho/m, ε = 50.84, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 2.42 V/m Peak SAR = 0.478 mW/g SAR(1 g) = 0.165 mW/g; SAR(10 g) = 0.0708 mW/g Power Drift = 0.03 dB Area Scan (13x27x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -12.3 -11.1 -9.85 -8.62 -7.39 -6.16 -4.92 -3.69 -2.46 -1.23 0 Date/Time: 04/07/03 23:25:06 Test Laboratory: Compliance Certification Services File Name: 3H-CH_0.141 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 1; Air temp 25 deg C & Liquid temp 22.6 deg C Communication System: DSSS; Frequency: 2462 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9368 mho/m, ε = 50.84, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 2.35 V/m Peak SAR = 0.424 mW/g SAR(1 g) = 0.141 mW/g; SAR(10 g) = 0.0607 mW/g Power Drift = -0.13 dB Area Scan (13x27x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -11.5 -10.3 -9.19 -8.04 -6.89 -5.74 -4.6 -3.45 -2.3 -1.15 0 Date/Time: 04/09/03 20:54:30 Test Laboratory: Compliance Certification Services File Name: 1L-CH_0.348 mW.da4 EUT Setup Configuration 2 SAR in dB -21 -18.9 -16.8 -14.7 -12.6 -10.5 -8.4 -6.3 -4.2 -2.1 0 Date/Time: 04/09/03 20:54:30 Test Laboratory: Compliance Certification Services File Name: 1L-CH_0.348 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 2; Air temp 25 deg C & Liquid temp 22.4deg C Communication System: DSSS; Frequency: 2412 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9341 mho/m, ε = 50.48, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 5.05 V/m Peak SAR = 1.09 mW/g SAR(1 g) = 0.348 mW/g; SAR(10 g) = 0.131 mW/g Power Drift = 0.03 dB Area Scan (12x30x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -21 -18.9 -16.8 -14.7 -12.6 -10.5 -8.4 -6.3 -4.2 -2.1 0 Date/Time: 04/09/03 21:38:32 Test Laboratory: Compliance Certification Services File Name: 2M-CH_0.355 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 2; Air temp 25 deg C & Liquid temp 22.3deg C Communication System: DSSS; Frequency: 2437 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9341 mho/m, ε = 50.48, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm Reference Value = 5.01 V/m Peak SAR = 1.11 mW/g SAR(1 g) = 0.355 mW/g; SAR(10 g) = 0.133 mW/g Power Drift = -0.03 dB Area Scan (12x30x1): Measurement grid: dx=10mm, dy=10mm SAR in dB -22.6 -20.3 -18.1 -15.8 -13.5 -11.3 -9.03 -6.77 -4.52 -2.26 0 Date/Time: 04/09/03 22:24:52 Test Laboratory: Compliance Certification Services File Name: 3H-CH_0.328 mW.da4 Applicant: Compal Trade Name: Motion Tablet M1300 Model: T002 Program: EUT Setup Configuration 2; Air temp 25 deg C & Liquid temp 22.3deg C Communication System: DSSS; Frequency: 2462 MHz; Duty Cycle: 1:1 Medium: Muscle 2450 MHz ( σ = 1.9341 mho/m, ε = 50.48, ρ = 1000 kg/m3) Phantom section: FlatSection DASY4 Configuration: - Probe: ET3DV6 - SN1577; ConvF(4.7, 4.7, 4.7); Calibrated: 2/7/2003 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn427; Calibrated: 2/4/2003 - Phantom: SAM 1 - TP:1185 - Software: DASY4, V4.0 Build 51 Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, d…

Text truncated - open the document above for the full version.

C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 1 of 39 Rev. 00 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Wireless LAN module build in Tablet PC MODEL No.: T002 FCC ID: GKRT0022100 REPORT NO: 030042-RF-ID ISSUE DATE: April 4, 2003 Prepared for Compal Electronics, Inc. No. 581, Juikuang Rd., Neihu, Taipei (114) Taiwan, R.O.C Prepared by C&C LABORATORY, CO., LTD. #B1, 1 st Fl., Universal Center, No. 183, Sec. 1, Tatung Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. TEL: (02)8642-2071~3 FAX: (02)8642-2256 C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 2 Rev. 00 VERIFICATION OF COMPLIANCE Applicant: Compal Electronics, Inc. No. 581, Juikuang Rd., Neihu, Taipei (114) Taiwan, R.O.C Product Description: Wireless LAN module build in Tablet PC Model No.: T002 Brand of RF Module: Intel RF Module No: WM3B2100 Model Difference N/A Serial Number: N/A File Number: 030042-RF-ID Date of test: March 27 ~ April 1, 2003 We hereby certify that: The above equipment was tested by C&C Laboratory Co., Ltd. The test data , data evaluation , test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (1992) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 The test results of this report relate only to the tested sample identified in this report. Approved By Vincent Su / Vice Manager C&C Laboratory Co., Ltd.. C&C Laboratory Co. Ltd. REPORT NO: 030042-RF-ID ID GKRT0022100 DATE: April 4, 2003 Page 3 Rev. 00 Table of Contents 1. GENERAL INFORMATION ........................................................................................... 5 1.1 P RODUCT D ESCRIPTION .....................................................................................................................5 1.2 R ELATED S UBMITTAL ( S ) / G RANT ( S ) ...............................................................................................5 1.3 T EST M ETHODOLOGY ........................................................................................................................5 1.4 T EST F ACILITY ...................................................................................................................................5 1.5 S PECIAL A CCESSORIES ......................................................................................................................5 1.6 E QUIPMENT M ODIFICATIONS .............................................................................................................5 2. SYSTEM TEST CONFIGURATION .............................................................................. 6 2.1 EUT C ONFIGURATION .......................................................................................................................6 2.2 EUT E XERCISE ..................................................................................................................................6 2.3 T EST P ROCEDURE ..............................................................................................................................6 2.4 C ONFIGURATION OF T ESTED S YSTEM ...............................................................................................7 3. SUMMARY OF TEST RESULTS ................................................................................... 8 4. DESCRIPTION OF TEST MODES ................................................................................ 8 5. SPURIOUS EMISSION TEST ......................................................................................... 9 5.1 S TANDARD A PPLICABLE ....................................................................................................................9 5.2 EUT S ETUP ........................................................................................................................................9 5.3 M EASUREMENT P ROCEDURE .............................................................................................................9 5.4 T EST SET-UP (B LOCK D IAGRAM OF C ONFIGURATION ) .................................................................10 5.5 M EASUREMENT E QUIPMENT U SED :.................................................................................................11 5.6 M EASUREMENT R ESULT ..................................................................................................................11 6. AC POWER LINE CONDUCTED EMISSION TEST ................................................ 24 6.1 S TANDARD A PPLICABLE ..................................................................................................................24 6.2 EUT S ETUP .......................................................................…

Text truncated - open the document above for the full version.