GKRWM3BBG32Notebook Computer With Built In WLAN Module

CL32 User Manual Safety Instructions Use the following safety guidelines to help protect yourself and your computer. When Using Your Computer CAUTION: Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn. l Do not attempt to service the computer yourself. Always follow installation instructions closely. l Do not carry a battery in your pocket, purse, or other container where metal objects (such as car keys) could short-circuit the battery terminals. The resulting excessive current flow can cause extremely high temperatures and may result in damage from burns. l Be sure that nothing rests on your AC adapter’s power cable and that the cable is not located where it can be tripped over or stepped on. l Place the AC adapter in a ventilated area, such as a desktop or on the floor, when you use it to run the computer or to charge the battery. Do not cover the AC adapter with papers or other items that will reduce cooling; also, do not use the AC adapter while it is inside a carrying case. l Do not push objects into air vents or openings of your computer. Doing so can cause fire or electric shock by shorting out interior components. l Use only the AC adapter and batteries that are approved for use with this computer. Use of another type of battery or AC adapter may risk fire or explosion. l Danger of explosion if battery is incorrectly replaced. l Replace only with the same or equivalent type battery recommended by the manufacturer. l Dispose of used batteries according to the manufacturer’s instructions. l Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. - 115 V/60 Hz in most of North and South America and some Far Eastern countries such as South Korea and Taiwan. - 100 V/50 Hz in eastern Japan and 100 V/60Hz in western Japan. - 230 V/50 Hz in most of Europe, the Middle East, and the Far East. l If you use an extension cable with your AC adapter, ensure that the total ampere rating of the products plugged in to the extension cable does not exceed the ampere rating of the extension cable. l To remove power from the computer, turn it off, remove the battery, and disconnect the AC adapter from the electrical outlet. l To help avoid the potential hazard of electric shock, do not connect or disconnect any cables or perform maintenance or reconfiguration of this product during an electrical storm. l Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions. l When setting up the computer for work, place it on a level surface. l When traveling, do not check the computer as baggage. You can put your computer through an X-ray security machine, but never put your computer through a metal detector. If you have the computer checked by hand, be sure to have a charged battery available in case you are asked to turn on the computer. l When traveling with the hard drive removed from the computer, wrap the drive in a non-conducting material, such as cloth or paper. If you have the drive checked by hand, be ready to install the drive in the computer. Your can put the hard drive through an X-ray security machine, but never put the drive through a metal detector. l When traveling, do not place the computer in overhead storage compartments where it could slide around. Do not drop your computer or subject it to other mechanical shocks. l Protect your computer, battery, and hard drive from environmental hazards such as dirt, dust, food, liquids, temperature extremes, and overexposure to sunlight. l When you move your computer between environments with very different temperature and/or humidity ranges, condensation may form on or within the computer. To avoid damaging the computer, allow sufficient time for the moisture to evaporate before using the computer. Ë NOTICE: When taking the computer from low-temperature conditions into a warmer environment or from high-temperature conditions into a cooler environment, allow the computer to acclimate to room temperature before turning on power. l When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable itself. As you pull out the connector, keep it evenly aligned to avoid bending any connector pins. Also, before you connect a cable make sure both connectors are correctly oriented and aligned. l Before you clean your computer, turn it off, unplug it from its power source, and remove the battery. l Handle components with care. Hold a component such as a memory module by its edges, not its pins. CAUTION: When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: l Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. l Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. l Do not use the telephone to report a gas leak in the vicinity of the leak. l Use only the power cord indicated in this manual. Regulatory Notices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user's authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there i…

Text truncated - open the document above for the full version.

Power of Attorney Date: January 28, 2004 We, the undersigned, hereby authorize Compliance Certification Services Inc. to act on our behalf in all matters relating to all processes related to FCC & IC applications and communications issue. Any and all acts carried out by Compliance Certification Services Inc. on our behalf shall have the same effects as acts of our own. If you have any questions regarding this authorization, please don’t hesitate to contact us. Thank you. Sincerely yours, _____________________________ George Chou / Manager Compal Electronics, Inc.

September 10, 2003 Federal Communications Commission Authorization and Evaluation Division FCC ID: GKRWM3BBG32 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1. Schematics 2. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, _____________________________ George Chou / Manager Compal Electronics, Inc.

Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 64 EXTERNAL PHOTOGRPHS OF EUT Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 65 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 66 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 67

FCC ID / IC LABEL FORMAT AND LOCATION Applicant: Compal Electronics Inc. FCC ID: GKRWM3BBG32 IC: 2533B-WM3B0B32 FCC ID: GKRWM3BBG32 IC: 2533B-WM3B0B32 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. “Complies with Canada RSS-210” LABEL AREA TESTED TO COMPLY WITH FCC STANDARDS FOR HOME OR OFFICE USE

Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 68 INTERNAL PHOTOGRPHS OF EUT Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 69 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 70 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 71 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 72 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 73 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 74

OEM Name or other identification Document Number: XXXX Rev: XX Drongo Antenna Information Wistron NeWeb Corporation Intel Regulatory Antenna Information Example Rev. 4 1/28 OEM Name or other identification Document Number: XXXX Rev: XX Drongo Antenna Information I. Antenna Assembly Specifications Antenna assembly overview: Peak Gain including cable loss. DesignatorManufactureAntenna type Cable Assembly Info.Peak Gain W/ Cable loss (dBi) 2400-2500MHz -0.2 dBi (peak) 5150-5350MHz 2.81 dBi (peak) 5470-5825MHz 1.93 dBi (peak) Main antenna (P/N:81.EBF15.001) WNCMetal PIFA 1.(1)Cable P/N:J12B1394-2,50ohm cable,length:323mm,diameter 1.13mm. (2)connector P/N:20278-101R-13, I-PEX or WNC connector . 2400-2500MHz 2.48 dBi (peak) 5150-5350MHz 2.25 dBi (peak) 5470-5825MHz 2.88 dBi (peak) Auxiliary antenna (P/N:81.EBF15.002)WNCMetal PIFA 1.(1)Cable P/N:J12B1394-1,50ohm cable,length:460mm,diameter 1.13mm. (2)connector P/N:20278-101R-13 ,I-PEX or WNC connector. Antenna overview: Peak Gain not including cable loss. Antenna DesignatorManufactureAntenna typePeak Gain w/o Cable Loss (dBi) 2400-2500MHz 0.8 dBi (peak) 5150-5350MHz 4.31 dBi (peak) 5470-5825MHz 3.53 dBi (peak) Main antenna (P/N:81.EBF15.001) WNCMetal PIFA ) 2400-2500MHz 3.88 dBi (peak) 5150-5350MHz 4.45 dBi (peak) 5470-5825MHz 5.18 dBi (peak) Auxiliary antenna (P/N:81.EBF15.002)WNC Metal PIFA Intel Regulatory Antenna Information Example Rev. 4 2/28 OEM Name or other identification Document Number: XXXX Rev: XX Cable assembly overview: Cable loss (including connector). DesignatorManufactureCable type and length VSWRCable Loss (dBi) 2400-2500MHz 1.59 max 2400-2500MHz 1dBi (peak) 5150-5350MHz 1.53 max 5150-5350MHz 1.5dBi (peak) 5470-5825MHz 1.84 max 5470-5825MHz 1.6dBi (peak) 1. P/N: 50.CAB02.011 2. P/N:50.EBF03.001 For use with the Main antenna WNC 1.(1)Cable P/N:J12B1394-2 coaxil cable,length:323mm,di a 1.13mm. (2)connector P/N:20278-1 0 I-PEX. 2.(1)Cable P/N: 2400-2500MHz 1.46 max 2400-2500MHz 1.4 dBi (peak) 5150-5350MHz 1.95 max 5150-5350MHz 2.2 dBi (peak) 5470-5825MHz 2.05 max 5470-5825MHz 2.3 dBi (peak) 1. P/N: 50.EBF01.001 2. P/N:50.EBF02.001 For use with the Auxiliary antenna WNC 1.(1)Cable P/N:J12B1394-1 coaxil cable,length:460mm,di a 1.13mm. (2)connector P/N:20278-1 0 ,I-PEX. 2. NOTE: For Japan, Korea, and China the antenna data is the same as what this document requests: Intel Regulatory Antenna Information Example Rev. 4 3/28 OEM Name or other identification Document Number: XXXX Rev: XX x Main antenna dimensioned drawing 48mm 17mm AUX antenna dimensioned drawing 10 ~20 mm 54mm 7m Intel Regulatory Antenna Information Example Rev. 4 4/28 OEM Name or other identification Document Number: XXXX Rev: XX Radiation characteristic of antennaeLoaded (In Host System)Radiation characteristic of antennaeLoaded (In Host System) 2400-2500MHz radiation characteristic Center Frquency 2400MHz Horizontal (dBi) Peak -0.35 Vertical (dBi) Peak -1.05 Horz + Vert (dBi) Peak -0.34 Intel Regulatory Antenna Information Example Rev. 4 5/28 OEM Name or other identification Document Number: XXXX Rev: XX Center Frquency 2450MHz Horizontal (dBi) Peak -0.561 Vertical (dBi) Peak -0.21 Horz + Vert (dBi) Peak -0.31 Intel Regulatory Antenna Information Example Rev. 4 6/28 OEM Name or other identification Document Number: XXXX Rev: XX Center Frquency 2500MHz Horizontal (dBi) Peak 0.86 Vertical (dBi) Peak -1.67 Horz + Vert (dBi) Peak -0.2 Intel Regulatory Antenna Information Example Rev. 4 7/28 OEM Name or other identification Document Number: XXXX Rev: XX Center Frquency 2400MHz Horizontal (dBi) Peak -0.23 Vertical (dBi) Peak0.12 Horz + Vert (dBi) Peak 2.01 Intel Regulatory Antenna Information Example Rev. 4 8/28 OEM Name or other identification Document Number: XXXX Rev: XX Center Frquency 2450MHz Horizontal (dBi) Peak -0.83 Vertical (dBi) Peak1.31 Horz + Vert (dBi) Peak 1.52 Intel Regulatory Antenna Information Example Rev. 4 9/28 OEM Name or other identification Document Number: XXXX Rev: XX Center Frquency 2500MHz Horizontal (dBi) Peak 0.01 Vertical (dBi) Peak2.43 Horz + Vert (dBi) Peak 2.48 Intel Regulatory Antenna Information Example Rev. 4 10/28

Compliance Certification Services Inc. Report No: B31209204-SAR-FCC Date of Issue: January 19, 2004 in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for Wireless LAN module built in Notebook PC Model: CL32(Intel b/g) FCC ID: GKRWM3BBG32 Prepared for COMPAL ELECTRONICS, INC. No. 581, Juikuang Rd., Neihu, Taipei, 114 Taiwan, R.O.C. Prepared by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Compliance Certification Services Inc. Report No: B31209204-SAR-FCC Date of Issue: January 19, 2004 CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: January 14, 2004 Applicant: COMPAL ELECTRONICS, INC. No. 581, Juikuang Rd., Neihu, Taipei, 114 Taiwan, R.O.C. Model Number: CL32(Intel b/g) FCC ID: GKRWM3BBG32 Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: 802.11b Direct Sequence Spread Spectrum 802.11g Orthogonal Frequency Division Multiplexing (OFDM) Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: (Conducted/Peak) 18.80dBm Max. SAR (1g): 0.212 W/kg Application Type: Certification FCC Rule Part(s): 15C Note: This Report is only applicable for 802.11b/g. This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1- 1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Approved by: Reviewed by: Jonson Lee / Director James Lee / Senior engineer Compliance Certification Services Inc. Compliance Certification Services Inc. Page 2 Compliance Certification Services Inc. Report No: B31209204-SAR-FCC Date of Issue: January 19, 2004 TABLE OF CONTENTS 1. EUT DESCRIPTION.....................................................................................................4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC ....5 3. DOSIMETRIC ASSESSMENT SYSTEM...................................................................5 3.1 MEASUREMENT SYSTEM DIAGRAM.........................................................................6 3.2 SYSTEM COMPONENTS.................................................................................................7 DASY4 Measurement Server.............................................................................................7 Data Acquisition Electronics (DAE)..................................................................................7 ET3DV6 Isotropic E-Field Probe for Dosimetric Measurements......................................7 SAM Phantom (V4.0) ........................................................................................................8 Device Holder for SAM Twin Phantom............................................................................8 System Validation Kits......................................................................................................8 4. EVALUATION PROCEDURES...................................................................................9 5. MEASUREMENT UNCERTAINTY.........................................................................12 6. EXPOSURE LIMIT.....................................................................................................13 7. MEASUREMENT RESULTS.....................................................................................14 7.1 SYSTEM PERFORMANCE CHECK..............................................................................14 7.2 TEST LIQUID CONFIRMATION...................................................................................15 7.3 EUT TUNE-UP PROCEDURES......................................................................................16 7.4 SAR MEASUREMENTS RESULTS...............................................................................17 8. EUT PHOTOS..............................................................................................................21 9. EQUIPMENT LIST & CALIBRATION STATUS...................................................23 10. REFERENCES.............................................................................................................24 11. ATTACHMENTS.........................................................................................................25 Page 3 Compliance Certification Services Inc. Report No: B31209204-SAR-FCC Date of Issue: January 19, 2004 1. EUT DESCRIPTION Applicant: COMPAL ELECTRONICS, INC. No. 581, Juikuang Rd., Neihu, Taipei, 114 Taiwan, R.O.C. Model Number: CL32(Intel b/g) FCC ID: GKRWM3BBG32 Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: 802.11b Direct Sequence Spread Spectrum 802.11g Orthogonal Frequency Division Multiplexing (OFDM) Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: (Conducted/Peak) 18.80dBm Max. SAR (1g): 0.212 W/kg Application Type: Certification FCC Rule Part(s): 15C Antennas: Metal PIFA Ant. Page 4 Compliance Certification Services Inc. Report No: B31209204-SAR-FCC Date of Issue: January 19, 2004 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE F…

Text truncated - open the document above for the full version.

Date/Time: 01/14/04 14:51:37 Test Laboratory: Compliance Certification Services Inc. D2450V2 SN 728 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL2450 (σ = 1.85 mho/m, ε r = 39.07, ρ = 1000 kg/m 3 ) Air Temperature:24.6 deg C;Liquid Temperature:23.1 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(5.1, 5.1, 5.1); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 12; Type: SAM V4.0; Serial: TP-1271 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.8 Build 62 Pin=250mW,d=10mm/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 94.1 V/m Power Drift = -0.008 dB Maximum value of SAR = 11.6 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 94.1 V/m Power Drift = -0.0 dB Maximum value of SAR = 20.7 mW/g Pin=250mW,d=10mm/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 30.7 W/kg SAR(1 g) = 13.9 mW/g; SAR(10 g) = 6.36 mW/g Reference Value = 94.1 V/m Power Drift = -0.008 dB Maximum value of SAR = 15.6 mW/g Page1 Page2 Date/Time: 01/14/04 16:19:28 Test Laboratory: Compliance Certification Services Inc. Test Configuration-1 Page1 Date/Time: 01/14/04 16:19:28 Test Laboratory: Compliance Certification Services Inc. Touch mode-Main DUT: Wireless LAN module built in Notebook PC; Type: CL32; Serial: N/A Communication System: IEEE 802.11b/g WLAN; Frequency: 2412 MHz;Duty Cycle: 1:4 Medium: BSL2450 (σ = 2 mho/m, ε r = 51.1, ρ = 1000 kg/m 3 ) Air Temperature:24.6 deg C;Liquid Temperature:23.1 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.8 Build 62 Low Rate=11M bit/Area Scan (11x15x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.86 V/m Power Drift = 0.1 dB Maximum value of SAR = 0.043 mW/g Low Rate=11M bit/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 2.86 V/m Power Drift = -0.1 dB Maximum value of SAR = 0.023 mW/g Low Rate=11M bit/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 0.083 W/kg SAR(1 g) = 0.041 mW/g; SAR(10 g) = 0.023 mW/g Reference Value = 2.86 V/m Power Drift = 0.1 dB Maximum value of SAR = 0.044 mW/g Page1 Page2 Date/Time: 01/14/04 16:19:28 Test Laboratory: Compliance Certification Services Inc. Touch mode-Main DUT: Wireless LAN module built in Notebook PC; Type: CL32; Serial: N/A Communication System: IEEE 802.11b/g WLAN; Frequency: 2437 MHz;Duty Cycle: 1:4 Medium: BSL2450 (σ = 2 mho/m, ε r = 51.1, ρ = 1000 kg/m 3 ) Air Temperature:24.6 deg C;Liquid Temperature:23.1 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.8 Build 62 mid Rate=11M bit/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3.2 V/m Power Drift = 0.2 dB Maximum value of SAR = 0.031 mW/g mid Rate=11M bit/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 3.2 V/m Power Drift = 0.2 dB Maximum value of SAR = 0.017 mW/g mid Rate=11M bit/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 0.057 W/kg SAR(1 g) = 0.030 mW/g; SAR(10 g) = 0.017 mW/g Reference Value = 3.2 V/m Power Drift = 0.2 dB Maximum value of SAR = 0.033 mW/g Page1 Page2 Date/Time: 01/14/04 16:19:28 Test Laboratory: Compliance Certification Services Inc. Touch mode-Main DUT: Wireless LAN module built in Notebook PC; Type: CL32; Serial: N/A Communication System: IEEE 802.11b/g WLAN; Frequency: 2462 MHz;Duty Cycle: 1:4 Medium: BSL2450 (σ = 2 mho/m, ε r = 51.1, ρ = 1000 kg/m 3 ) Air Temperature:24.6 deg C;Liquid Temperature:23.1 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechanical And Optical Surface Detection) Sensor-Surface: 0mm (Fix Surface) z Electronics: DAE3 Sn558; Calibrated: 3/7/2003 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.1 Build 47; Postprocessing SW: SEMCAD, V1.8 Build 62 High Rate=11M bit/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3 V/m Power Drift = -0.1 dB Maximum value of SAR = 0.025 mW/g High Rate=11M bit/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Reference Value = 3 V/m Power Drift = -0.1 dB Maximum value of SAR = 0.013 mW/g High Rate=11M bit/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Peak SAR (extrapolated) = 0.051 W/kg SAR(1 g) = 0.025 mW/g; SAR(10 g) = 0.013 mW/g Reference Value = 3 V/m Power Drift = -0.1 dB Maximum value of SAR = 0.026 mW/g Page1 Page2 Date/Time: 01/14/04 22:53:51 Test Laboratory: Compliance Certification Services Inc. Touch mode-Main-G mode DUT: Wireless LAN module built in Notebook PC; Type: CL32; Serial: N/A Communication System: IEEE 802.11b/g WLAN; Frequency: 2412 MHz;Duty Cycle: 1:20 Medium: BSL2450 (σ = 2 mho/m, ε r = 51.1, ρ = 1000 kg/m 3 ) Air Temperature:24.6 deg C;Liquid Temperature:23.1 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ET3DV6 - SN1762; ConvF(4.6, 4.6, 4.6); Calibrated: 3/31/2003 z Sensor-Surface: 4mm (Mechani…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 of 74 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Compal Electronics Inc. Wireless LAN module built in Notebook PC Model: CL32 Trade Name: Compal / acer Prepared for Compal Electronics Inc. No. 581, Juikuang Rd., Neihu, Taipei, (114) Taiwan, R.O.C. Prepared by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 2 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION................................................................................................... 3 2. EUT DESCRIPTION .......................................................................................................................... 4 3. TEST METHODOLOGY ................................................................................................................... 5 3.1 EUT CONFIGURATION....................................................................................................................... 5 3.2 EUT EXERCISE................................................................................................................................... 5 3.3 GENERAL TEST PROCEDURES............................................................................................................ 5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS....................................................... 6 3.5 DESCRIPTION OF TEST MODES.......................................................................................................... 6 4. INSTRUMENT CALIBRATION....................................................................................................... 7 5. FACILITIES AND ACCREDITATIONS ......................................................................................... 8 5.1 FACILITIES .......................................................................................................8 5.2 EQUIPMENT....................................................................................................................................... 8 5.3 LABORATORY ACCREDITATIONS AND LISTING................................................................................. 8 5.4 TABLE OF ACCREDITATIONS AND LISTINGS...................................................................................... 9 6. SETUP OF EQUIPMENT UNDER TEST ...................................................................................... 10 6.1 SUPPORT EQUIPMENT..................................................................................................................... 10 7. FCC PART 15.247 REQUIREMENTS............................................................................................ 11 7.1 6DB BANDWIDTH............................................................................................................................ 11 7.2 PEAK POWER................................................................................................................................... 16 7.3 BAND EDGES MEASUREMENT ............................................................................................... 21 7.4 PEAK POWER SPECTRAL DENSITY................................................................................................... 30 7.5 RADIO FREQUENCY EXPOSURE....................................................................................................... 35 7.6 SPURIOUS EMISSIONS ............................................................................................................... 36 7.7 POWERLINE CONDUCTED EMISSIONS.............................................................................................. 58 Compliance Certification Services Inc. Report No: B31209204-RP FCC ID: GKRWM3BBG32 Date of Issue: Jan. 15, 2004 Page 3 1. TEST RESULT CERTIFICATION Applicant: Compal Electronics Inc. No. 581, Jui Kuang Rd., Neihu, Taipei, (114) Taiwan, R.O.C. Equipment Under Test: Wireless LAN module built in Notebook PC Tr a d e N a m e : C…

Text truncated - open the document above for the full version.